Synthesis and supercapacitance of flower-like Co(OH)<Subscript>2</Subscript> hierarchical superstructures self-assembled by mesoporous nanobelts

A facile hydrothermal strategy was first proposed to synthesize flower-like Co(OH)₂ hierarchical microspheres. Further physical characterizations revealed that the flower-like Co(OH)₂ microspherical superstructures were self-assembled by one-dimension nanobelts with rich mesopores. Electrochemical performance of the flower-like Co(OH)₂ hierarchical superstructures were investigated by cyclic voltammgoram, galvanostatic charge–discharge and electrochemical impedance spectroscopy in 3 M KOH aqueous electrolyte. Electrochemical data indicated that the flower-like Co(OH)₂ superstructures delivered a specific capacitance of 434 F g⁻¹ at 10 mA cm⁻² (about 1.33 A g⁻¹), and even kept it as high as 365 F g⁻¹ at about 5.33 A g⁻¹. Furthermore, the SC degradation of about 8% after 1,500 continuous charge–discharge cycles at 5.33 A g⁻¹ demonstrates their good electrochemical stability at large current densities.     

Preparation and performance comparison of LiMn2O3.95Br0.05 and LiMn2O3.95Br0.05/SiO2 cathode materials for lithium-ion battery

LiMn₂O_3.95Br_0.05 and LiMn₂O_3.95Br_0.05/SiO₂ cathode composites for lithium-ion battery are prepared by solid-state reaction methods. The crystalline structures of the as-synthesized samples are investigated by X-ray diffraction and transmission electron microscope; at the same time, the electrochemical performances are tested by cyclic voltammetry and galvanostatic cycling. The results reveal that the sample of LiMn₂O_3.95Br_0.05/SiO₂ has more excellent electrochemical performance than the sample of LiMn₂O_3.95Br_0.05. It delivers an initial discharge capacity of 145.3 mA h g⁻¹ at ambient temperature, and 138.9 mA h g⁻¹ at the higher temperature of 55 °C with good capacity retention with the voltage range of 3.0–4.35 V (vs. Li) at a current density of 0.5 C; while the sample of LiMn₂O_3.95Br_0.05 only deliver initial discharge capacity 136.5 mA h g⁻¹ at ambient temperature, and 119.2 mA h g⁻¹ at 55 °C in the same conditions; in addition, the rate performance of LiMn₂O_3.95Br_0.05/SiO₂ is excellent too, so the SiO₂ layer has improved the electrochemical behaviors of LiMn₂O_3.95Br_0.05 availably.     

Fabrication of TiO2/Ti nanotube electrode and the photoelectrochemical behaviors in NaCl solutions

Titanium oxide nanotube electrodes were successfully prepared by anodic oxidation on pure Ti sheets in 0.5 wt.% NH₄F + 1 wt.% (NH₄)₂SO₄ + 90 wt.% glycerol mixed solutions. Nanotubes with diameter 40–60 nm and length 7.4 μm were observed by field emission scanning electron microscope. The electrochemical and photoelectrochemical characteristics of TiO₂ nanotube electrode were investigated using linear polarization and electrochemical impedance spectroscopy techniques. The open-circuit potential dropped markedly under irradiation and with the increase of Cl⁻ concentrations. A saturated photocurrent of approximately 1.3 mA cm⁻² was observed under 10-W low-mercury lamp irradiation in 0.1 M NaCl solution, which was much higher than film electrode. Meanwhile, the highest photocurrent in NaCl solution implied that the photogenerated holes preferred to combine with Cl⁻. Thus, a significant synergetic effect on active chlorine production was observed in photoelectrocatalytic processes. Furthermore, the generation efficiency for active chlorine was about two times that using TiO₂/Ti film electrode by sol–gel method. Finally, the effects of initial pH and Cl⁻ concentration were also discussed.     

Electro-catalysis by immobilised human flavin-containing monooxygenase isoform 3 (hFMO3)

Human flavin-containing monooxygenases are the second most important class of drug-metabolizing enzymes after cytochromes P450. Here we report a simple but functional and stable enzyme-electrode system based on a glassy carbon (GC) electrode with human flavin-containing monooxygenase isoform 3 (hFMO3) entrapped in a gel cross-linked with bovine serum albumin (BSA) by glutaraldehyde. The enzymatic electrochemical responsiveness is characterised by using well-known substrates: trimethylamine (TMA), ammonia (NH₃), triethylamine (TEA), and benzydamine (BZD). The apparent Michaelis–Menten constant (K′_M) and apparent maximum current (I′_max) are calculated by fitting the current signal to the Michaelis–Menten equation for each substrate. The enzyme-electrode has good characteristics: the calculated sensitivity was 40.9 ± 0.5 mA mol⁻¹ L cm⁻² for TMA, 43.3 ± 0.1 mA mol⁻¹ L cm⁻² for NH₃, 45.2 ± 2.2 mA mol⁻¹ L cm⁻² for TEA, and 39.3 ± 0.6 mA mol⁻¹ L cm⁻² for BZD. The stability was constant for 3 days and the inter-electrode reproducibility was 12.5%. This is a novel electrochemical tool that can be used to investigate new potential drugs against the catalytic activity of hFMO3.     

Magnesium ion-conducting gel polymer electrolytes dispersed with fumed silica for rechargeable magnesium battery application

Effect of fumed silica dispersion on poly(vinylidene fluoride-co-hexafluoropropylene)-based magnesium ion-conducting gel polymer electrolyte has been studied using various physical and electrochemical techniques. The composite gel electrolytes are free-standing and flexible films with enough mechanical strength. The optimized composition with 3 wt.% filler offers a maximum ionic conductivity of ∼1.1 × 10⁻² S cm⁻¹ at ∼25 °C with good thermal and electrochemical stabilities. The Mg²⁺ ion conduction in the gel nanocomposite film is confirmed from the cyclic voltammetry, impedance spectroscopy, and transport number measurements. The space-charge layers formed between filler particles and gel electrolyte are responsible for the enhancement in ionic conductivity. The applicability of the gel nanocomposite to a rechargeable battery is examined by fabricating a prototype cell consisting of Mg [or Mg-multiwalled carbon nanotube (MWCNT) composite] and MoO₃ as negative and positive electrodes, respectively. The discharge capacity and the rechargeability of the cell have been improved when Mg metal is substituted by Mg-MWCNT composite. The discharge capacity of the optimized cell has found to be ∼175 mAh g⁻¹ of MoO₃ for an initial ten charge–discharge cycles.     

Effect of ionic conductivity of a PAN–PC–LiClO<Subscript>4</Subscript> solid polymeric electrolyte on the performance of a TiO<Subscript>2</Subscript> photoelectrochemical cell

A nanoparticle TiO₂ solid-state photoelectrochemical cell has been fabricated. The effect of ionic conductivity of a solid electrolyte of polyacrylonitrile (PAN)–propylene carbonate (PC)–lithium perchlorate (LiClO₄) on the performance of a photoelectrochemical cell of indium tin oxide (ITO)/TiO₂/PAN–PC–LiClO₄/graphite has been investigated. A nanoparticle TiO₂ film was deposited onto ITO-covered glass substrate by controlled hydrolysis technique. A solid electrolyte of PAN–LiClO₄ with PC plasticizer prepared by solution casting technique was used as a redox couple medium. The room temperature conductivity of the electrolyte was determined by AC impedance spectroscopy technique. A graphite electrode was prepared onto a glass slide by electron beam evaporation technique. The device shows a photovoltaic effect under illumination. The short-circuit current density, J _sc, and open-circuit voltage, V _oc, vary with the conductivity of the electrolyte. The highest J _sc of 2.82 μA cm⁻² and V _oc of 0.56 V were obtained at the conductivity of 4.2 × 10⁻⁴ Scm⁻¹ and at the intensity of 100 mW cm⁻².     

Electrochemical studies of LiMnPO4 as aqueous rechargeable lithium–ion battery electrode

A study of the electrochemical behavior of LiMnPO₄ prepared by RAPET method in different aqueous electrolytes using cyclic voltammetry (CV), galvanostatic charge–discharge experiments, and electrochemical impedance spectroscopy is reported. CV peak current is proportional to the square root of scan rate under 0.2 mV s⁻¹. The system satisfied the required conditions for a reversible system with a resistive behavior. LiMnPO₄ was found to undergo proton insertion at lower concentrations of electrolyte. At higher concentrations or saturated solutions of electrolytes, lithium insertion/de-insertion becomes the main reaction though the effect of proton insertion/de-insertion reaction cannot be ignored. Electrochemical insertion/de-insertion of lithium in LiMnPO₄ was studied using EIS technique. The kinetic parameter, charge transfer resistance (R _ct), obtained by simulating the experimental impedance data with an equivalent circuit showed a minimum at the potential close to the CV peak potential. The cell LiTi₂(PO₄)₃/5 M LiNO₃/LiMnPO₄ delivers a discharge capacity of 84 mAh g⁻¹ in the first cycle at an applied current of 0.2 mA cm⁻² and it retains its initial capacity over 50 cycles with good rate capability.     

Synthesis and electrochemical performances of Li4Ti4.95Zr0.05O12/C as anode material for lithium-ion batteries

Spinel Li₄Ti_5 − x Zr _x O₁₂/C (x = 0, 0.05) were prepared by a solution method. The structure and morphology of the as-prepared samples were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The electrochemical performances including charge–discharge (0–2.5 V and 1–2.5 V), cyclic voltammetry, and ac impedance were also investigated. The results revealed that the Li₄Ti_4.95Zr_0.05O₁₂/C had a relatively smaller particle size and more regular morphology than that of Li₄Ti₅O₁₂/C. Zr⁴⁺ doping enhanced the ability of lithium-ion diffusion in the electrode. It delivered a discharge capacity 289.03 mAh g⁻¹ after 50 cycles for the Zr⁴⁺-doped Li₄Ti₅O₁₂/C while it decreased to 264.03 mAh g⁻¹ for the Li₄Ti₅O₁₂/C at the 0.2C discharge to 0 V. Zr⁴⁺ doping did not change the electrochemical process, instead enhanced the electronic conductivity and ionic conductivity. The reversible capacity and cycling performance were effectively improved especially when it was discharged to 0 V.     

Nano-composites SnO(VO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>) as anodes for lithium ion batteries

Nano-composites of SnO(V₂O₃) _x (x = 0, 0.25, and 0.5) and SnO(VO)_0.5 are prepared from SnO and V₂O₃/VO by high-energy ball milling (HEB) and are characterized by X-ray diffraction (XRD), scanning electron microscopy, and high-resolution transmission electron microscopy techniques. Interestingly, SnO and SnO(VO)_0.5 are unstable to HEB and disproportionate to Sn and SnO₂, whereas HEB of SnO(V₂O₃) _x gives rise to SnO₂.VO _x . Galvanostatic cycling of the phases is carried out at 60 mA g⁻¹ (0.12 C) in the voltage range 0.005–0.8 V vs. Li. The nano-SnO(V₂O₃)_0.5 showed a first-charge capacity of 435 (±5) mAh g⁻¹ which stabilized to 380 (±5) mAh g⁻¹ with no noticeable fading in the range of 10–60 cycles. Under similar cycling conditions, nano-SnO (x = 0), nano-SnO(V₂O₃)_0.25, and nano-SnO(VO)_0.5 showed initial reversible capacities between 630 and 390 (±5) mAh g⁻¹. Between 10 and 50 cycles, nano-SnO showed a capacity fade as high as 59%, whereas the above two VO _x -containing composites showed capacity fade ranging from 10% to 28%. In all the nano-composites, the average discharge potential is 0.2–0.3 V and average charge potential is 0.5–0.6 V vs. Li, and the coulombic efficiency is 96–98% after 10 cycles. The observed galvanostatic cycling, cyclic voltammetry, and ex situ XRD data are interpreted in terms of the alloying–de-alloying reaction of Sn in the nano-composite “Sn-VO _x -Li₂O” with VO _x acting as an electronically conducting matrix.     

Impedance studies on the 5-V cathode material,LiCoPO<Subscript>4</Subscript>

Olivine-structured LiCoPO₄ is synthesized by a Pechini-type polymer precursor method. The structure and the morphology of the compounds are studied by the Rietveld-refined X-ray diffraction, scanning electron microscopy, Brunauer, Emmett, and Teller surface area technique, infrared spectroscopy, and Raman spectroscopy techniques, respectively. The ionic conductivity (σ ionic), dielectric, and electric modulus properties of LiCoPO₄ are investigated on sintered pellets by impedance spectroscopy in the temperature range, 27–50 °C. The σ (ionic) values at 27 and 50 °C are 8.8 × 10⁻⁸ and 49 × 10⁻⁸ S cm⁻¹, respectively with an energy of activation (E _a) = 0.43 eV. The electric modulus studies suggest the presence of non-Debye type of relaxation. Preliminary charge–discharge cycling data are presented.     

Preparation and electrocatalytic performance of Fe–N–C for electroreduction of H2O2

Fe–N–C catalysts were prepared through metal-assisted polymerization method. Effects of carbon treatment, Fe loading, nitrogen source, and calcination temperature on the catalytic performance of the Fe–N–C for H₂O₂ electroreduction were measured by voltammetry and chronoamperometry. The Fe–N–C catalyst shows optimal performance when prepared with pretreated active carbon, 0.2 wt.% Fe, paranitroaniline (4-NA) and one-time calcination. The Fe–N–C catalyst displayed good performance and stability for electroreduction of H₂O₂ in alkaline solution. An Al–H₂O₂ semi-fuel cell was set up with Fe–N–C catalyst as cathode and Al as anode. The cell exhibits an open-circuit voltage of 1.3 V and its power density reached 51.4 mW cm⁻² at 65 mA cm⁻².     

Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

Electrochemical characterization of 2, 2′-[1, 2-ethanediylbis (nitriloethylidyne)]-bis-hydroquinone-carbon nanotube paste electrode and its application to simultaneous voltammetric determination of ascorbic acid and uric acid

The preparation and electrochemical characterization of a carbon nanotube paste electrode modified with 2,2′-[1,2-ethanediylbis (nitriloethylidyne)]-bis-hydroquinone, referred to as EBNBH, was investigated. The EBNBH carbon nanotube paste electrode (EBNBHCNPE) displayed one pair of reversible peaks at E _pa = 0.18 V and E _pc = 0.115 V vs Ag/AgCl. Half wave potential (E _1/2) and ΔE _p were 0.148 and 0.065 V vs Ag/AgCl, respectively. The electrocatalytic oxidation of ascorbic acid (AA) has been studied on EBNBHCNPE, using cyclic voltammetry, differential pulse voltammetry and chronoamperometry techniques. It has been shown that the oxidation of AA occurs at a potential where oxidation is not observed at the unmodified carbon paste electrode. The heterogeneous rate constant for oxidation of AA at the EBNBHCNPE was also determined and found to be about 1.07 × 10⁻³ cm s⁻¹. The diffusion coefficient of AA was also estimated as 5.66 × 10⁻⁶ cm² s⁻¹ for the experimental conditions, using chronoamperometry. Also, this modified electrode presented the property of electrocatalysing the oxidation of AA and uric acid (UA) at 0.18 and 0.35 V vs Ag/AgCl, respectively. The separations of anodic peak potentials of AA and UA reached 0.17 V. Using differential pulse voltammetry, the calibration curves for AA and UA were obtained over the range of 0.1–800 μM and 20–700 μM, respectively. With good selectivity and sensitivity, the present method provides a simple method for selective detection of AA and UA in biological samples.     

LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2−x</Subscript>Ti<Subscript>x</Subscript>O<Subscript>2</Subscript> nanoparticles: synthesis,structure, and evaluation of electrochemical properties for lithium ion cell application

Layered Ti-doped lithiated nickel cobaltate, LiNi_0.8Co_{0.2 − x}Ti_xO₂ (where x = 0.01, 0.03, and 0.05) nanopowders were prepared by wet-chemistry technique. The structural properties of synthesized materials were characterized by X-ray diffraction (XRD) and thermo-gravimetric/differential thermal analysis (TG/DTA). The morphological changes brought about by the changes in composition of LiNi_0.8Co_{0.2 − x}Ti_xO₂ particles were examined through surface examination techniques such as scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses. Electrochemical studies were carried out using 2016-type coin cell in the voltage range of 3.0–4.5 V (vs carbon) using 1 M LiClO₄ in ethylene carbonate and diethyl carbonate as the electrolyte. Among the various concentrations of Ti-doped lithiated nickel cobaltate materials, C/LiNi_0.8Co_0.17Ti_0.03O₂ cell gives stable charge–discharge features.     

Glycine-assisted hydrothermal synthesis of nanostructured Co x Ni1−x –Al layered triple hydroxides as electrode materials for high-performance supercapacitors

Nanostructured Co _x Ni_1−x –Al layered triple hydroxides (Co _x Ni_1−x –Al LTHs) have been successfully synthesized by a facile hydrothermal method using glycine as chelating agent. The samples were characterized by X-ray diffraction, thermogravimetry, Fourier transform infrared spectroscopy and scanning electron microscopy. The morphologies of Co _x Ni_1−x –Al LTHs varied with the Co content and its effect on the electrochemical behavior was studied by cyclic voltammetry and galvanostatic charge–discharge techniques. Electrochemical data demonstrated that the Co _x Ni_1−x –Al LTHs with Co/Ni molar ratio of 3:2 owned the best performance and delivered a maximum specific capacitance of 1,375 F g⁻¹ at a current density of 0.5 A g⁻¹ and a good high-rate capability. The capacitance retained 93.3% of the initial value after 1,000 continuous charge–discharge cycles at a current density of 2 A g⁻¹.     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Preparation and characterization of AuPt alloy nanoparticle–multi-walled carbon nanotube–ionic liquid composite film for electrocatalytic oxidation of cysteine

Gold–platinum (AuPt) alloy particles were fabricated directly on multi-walled carbon nanotubes (MWNT)–ionic liquid (i.e., trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl)imide, [P_6,6,6,14][NTf₂]) composite coated glassy carbon electrode (GCE) by electrodeposition method. Scanning electron microscope image showed that they were well-dispersed nanocluster consisting of smaller nanoparticles, and their size was about 70 nm. X-ray diffraction experiment showed that they were single-phase alloy nanomaterial, and the calculated composition was consisting with that obtained by energy dispersive X-ray spectroscopy. The resulting modified electrode (i.e., AuPt–MWNT–[P_6,6,6,14][NTf₂]/GCE) presented high catalytic activity for the electrochemical oxidation of cysteine. The peak potential of cysteine shifted to 0.42 V (versus saturated calomel electrode) in 0.1 M H₂SO₄ and the peak current increased greatly in comparison with that on the corresponding Pt (or Au)–MWNT–[P_6,6,6,14][NTf₂]/GCE. Under the optimized conditions, the oxidation current of cysteine at 0.45 V was linear to its concentration in the range of 5.0 × 10⁻⁷ ∼ 4.0 × 10⁻⁵ M with a sensitivity of 43.8 mA M⁻¹.     

Application of chitosan/iota-carrageenan polymer electrolytes in electrical double layer capacitor (EDLC)

In this work, a chitosan/iota (ι)-carrageenan blended film doped with orthophosphoric acid (H₃PO₄) as ionic dopant and poly(ethylene glycol) (PEG) as plasticizer has been used as a separator and electrolyte in an electrical double layer capacitor (EDLC). A set of samples were prepared by the solution cast technique to see the effect of the different weight ratios of the proton donor and plasticizer on the conductivity. The highest conducting sample has composition 37.50 wt.% chitosan–37.50 wt.% ι-carrageenan–18.75 wt.% H₃PO₄–6.25 wt.% PEG. The conductivity value is 6.29 × 10⁻⁴ S cm⁻¹. The conductivity–temperature relationship is Arrhenian, and the activation energy for the highest conducting sample is 0.09 eV. The specific discharge capacitance of the EDLC is 35 F g⁻¹ at 0.11 mA cm⁻² current drain and was constant for 30 cycles.     

Electrochemical intercalation of O2− in CuAlO2 single crystal and photoelectrochemical properties

The delafossite CuAlO₂ single crystal, prepared by the flux method, is a low mobility p-type semiconductor with a hole mobility of 1.2 × 10⁻⁵ cm⁻² V⁻¹ s⁻¹. The chronoamperometry showed an electrochemical O²⁻ insertion with a diffusion coefficient D _303K of 3.3 × 10⁻¹⁸ cm² s⁻¹. The thermal variation of D in the range 293–353 K gave an enthalpy of diffusion (ΔH) of 44.7 kJ mol⁻¹. CuAlO₂ is photoactive, and the Mott–Schottky plot indicates a flat band potential of +0.42 V vs saturated calomel electrode and a holes density (N _A) of 10¹⁶ cm⁻³. The photocurrent spectra have been analyzed by using the Gartner model from which the absorption coefficients and diffusion lengths were determined. An optical transition at 1.66 eV, indirectly allowed, has been obtained. The spectral photoresponse provides a high absorption at 480 nm. The low quantum yield (η) is attributed to a small depletion length (440 nm) and a hole diffusion width (271 nm) compared to a very large penetration depth (12 μm).     

Improvement of high-voltage cycling behavior of Li(Ni1/3Co1/3Mn1/3)O2 cathodes by Mg, Cr, and Al substitution

To improve the electrochemical properties of Li[Ni_1/3Co_1/3Mn_1/3]O₂ at high charge end voltage (4.6 V), a series of the mixed transition metal compounds, Li(Ni_1/3Co_{1/3 − x} Mn_1/3M _x )O₂ (M = Mg, Cr, Al; x = 0.05), were synthesized via hydroxide coprecipitation method. The effects of doping Mg, Cr, and Al on the structure and the electrochemical performances of Li[Ni_1/3Co_1/3Mn_1/3]O₂ were compared by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), galvanostatic charge–discharge tests, and electrochemical impedance spectroscopy. The XRD results show that all the samples keep layered structures with R3m space group as the Li[Ni_1/3Co_1/3Mn_1/3]O₂. SEM images show that all the compounds have spherical shapes and the Cr-doped sample has the largest particle size. Furthermore, galvanostatic charge–discharge tests confirm that the Cr-doped electrode shows improved cycling performance than the undoped material. The capacity retention of Li(Ni_1/3Co_{1/3 − 0.05}Mn_1/3Cr_0.05)O₂ is 97% during 50 cycles at 2.8∼4.6 V. The improved cycling performance at high voltage can be attributed to the larger particle size and the prevention of charge transfer resistance (R _ct) increase during cycling.