Cation-exchange separation of uranium from thorium in nitric acid medium</p> </p>

Summary Sorption behavior of Th and U on cation-exchange resins was investigated from nitric acid medium by both batch and column methods. The cation-exchange studies involved the sorption of UO₂²⁺ and Th⁴⁺ and their cationic complexes onto Dowex 50Wx8 and Dowex 50Wx4 resins (50-100 mesh). The batch data yielded a separation factor (K_d,Th/K_d,U) value of >100 for the cation-exchanger, Dowex 50Wx4 at 1-2M HNO₃. Separation of uranium from thorium was also carried out by column method in nitric acid medium using cation-exchangers, Dowex 50Wx4 as well as Dowex 50Wx8. While uranium elution was possible at 1M HNO₃, Th could be eluted only at higher concentration of nitric acid (>6M). The stripped solution emanating from a mixer settler employing di-2-ethyl hexyl isobutyramide as extractant and feed solution similar to THOREX process comprising 350 mg/l U and 380 mg/l Th in 0.75M HNO₃ was loaded on the column and the decontamination factor value for U in the product was >1000.</p> </p>     

Preconcentration of 198Au in a green alga, Rhizoclonium</p> </p>

Summary The bioaccumulation of ¹⁹⁸Au radionuclide, by Rhizoclonium riparium a member of Chlorophyceae has been studied. It has been observed that accumulation of gold on Rhizoclonium is almost pH independent and slightly higher at basic pH. Accumulation of gold was studied with ¹⁹⁸Au radiotracer, 0.1, 1 and 5 ppm concentrations of gold. It has been concluded from the biochemical analysis that the gold accumulation is due to adsorption in the cellulose and not in protein, fat and carbohydrate. Accumulated gold was recovered when washed with conc. HNO₃.</p> </p>     

Radiation effects on gaseous iodine at very low concentrations</p> </p>

Summary Exploratory experiments have been carried out to investigate the effects of gamma-radiation on iodine aerosols under various chemical conditions. The results indicate that iodide ions (I^-) in aerosol can be readily oxidized to I₂ and HIO, and some iodide ions may be converted to organic iodine when organic additives are present in the KI solution from which the aerosol is generated. The results also suggest that the chemical transformation of irradiated iodine aerosol depends on the chemical environment both carrier gas and iodide solution.</p> </p>     

Thermodynamic modeling for the removal of Cs+, Sr2+, Ca2+and Mg2+ions from aqueous waste solutions using zeolite A</p> </p>

Summary The batch removal ofCs⁺, Sr²⁺, Ca²⁺and Mg²⁺ions from aqueous solutions using synthetic zeolite A was investigated. The influence of the initial ion concentration, pH and temperature was studied. The obtained isotherm data have been correlated with Langumir, Freundlich, and Dubinin-Radushkevich(D-R) isotherm models. The effect of the temperature on the equilibrium distribution values has been utilized to evaluate the standard thermodynamic parameters such as free energy (DG), enthalpy (DH) and entropy (DS). Based on the D-R isotherm expression, the maximum ion-exchange capacity and the mean free energy of each studied ion has been determined. The selectivity sequence, deduced from the equilibrium isotherm data is: Sr²⁺>Ca²⁺>Mg²⁺>Cs⁺>Na⁺.</p> </p>     

Sorption of Co, Cs, Sr and I onto argillaceous rock as studied by radiotracers</p> </p>

Summary Sorption of⁶⁰Co,⁸⁵Sr, 137Cs and¹²⁵I have been studied on samples originated from Boda (siltstone-) claystone formation (BCF) (Hungary). The distribution of K_dvalues have been determined in static batch experiments using natural groundwater. The order of sorption of isotopes was Co>Cs>Sr>I, where iodine exhibits sorption properties in a modest extent. The sorption isotherm was determined for Cs from measurements carried out in 10^-5-10^-1M initial concentration range. The isotherm can be described with non-linear Freundlich approximation in the range of</o:p></p> 10^-7-10^-4M equilibrium concentration. At concentrations >10^-2M the isotherm achieves saturation. Hence, it is suggested that sorption of Cs on BCF is dominated by cation-exchange reactions on the illite mineral component. In the case of Co and Sr, precipitation reactions occurred during the experiments performed with carrier-containing solutions. This can be attributed to the low values of solubility product constants of SrCO₃, SrSO₄and Co(OH)₂, formed from anions present in the natural groundwater.</p> </p>     

Removal of uranyl ions from wastewaters using cellulose and modified cellulose materials</p> </p>

Summary Three silylcellulosic derivatives with different substitution degree were examined as sorbents for uranyl ions. The adsorption rate and capacity of cellulose and modified cellulose were investigated in aqueous media, at various pH and temperature values. The polymer - metal complexes of UO₂²⁺ were characterized by infrared and electronic spectra, and thermogravimetry. The thermal behavior of cellulose (C), trimethylsilyl - cellulose (tmsc, SD= 2.85) and triphenylsilyl - cellulose (TPSC1, SD=2.89 and TPSC2, SD =2.70) and their complexes with uranyl ions in atmospheric air has been studied between room temperature and 600 °C. The Coats-Redfern method was applied to estimate the kinetic parameters. The results revealed that the complexation of C and TMSC with UO₂²⁺ increases the thermal stability.</p> </p>     

Investigation of 85Sr adsorption in the presence of Na+, K+ and Cs+ on selected soils from different horizons</p> </p>

Summary Results of studies of Na⁺, K⁺ and Cs⁺ influence on the adsorption of ⁸⁵Sr on soil samples of the different types of successive horizons are presented. It was proved that the adsorption isotherms in log-log coordinates are of straight-line type and may be described by the Freundlich equation. Monovalent cations influence the coverage degree of the soil surface by ⁸⁵Sr (most often lowering it) in the following order K⁺3Na⁺3Cs⁺. The investigation of pH influence proved its essential meaning in the process. The plateau of surface coverage degree versus pH lies above pH 5.5 or 6.5 depending on the soil type. Generally, in the studied system, the size of ⁸⁵Sr adsorption depends on the concentration of the isotope, pH of the solution, type of monovalent cation, and on the soil properties.</p> </p>     

Mathematical modeling of separation of microamounts of strontium from yttrium in water - HCl -nitrobenzene - 15-crown-5 - hydrogen a dicarbollylcobaltate extraction system</p> </p>

Summary A rapid separation of microamounts of Sr²⁺ from Y³⁺ using HCl, 15-crown-5 (15C5) and hydrogen dicarbollylcobaltate (H⁺B^-) in the two-phase water - nitrobenzene extraction system was developed. The reached separation factor a(Sr/Y) was approximately 10. ^5.4</p> __</p>     

Selective separation of uranium using trimethylammonium acetosalycoylhydrazone modified Duolite C20 resin</p> </p>

Summary Duolite C20 resin modified with trimethylammonium acetosalycoylhydrazone has been developed, for the selective separation and/or preconcentration of uranium. The modified resin was characterized by elemental analysis and infrared spectra. Batch and column modes were applied. The newly designed resin quantitatively sorbs uranium ion at pH 3 when the flow rate equals to 2 ml ^. min ^-1 . The sorption capacity was 0.750 mmol ^. g^-1 for uranium ion, whereas its preconcentration factor was 200. The lower limit of detection was 5 ng ^. ml^-1 and its desorption was effective with 5 ml of 3 mol ^. l^-1 HCl or HNO₃ prior to detection spectrophotometry. The modified resin was highly ion-selective in nature even in the presence of large concentrations of electrolyte or organic media, with a preconcentrating ability for uranium ion. The modified resin was tested on its utility with synthetic, real and certified ore samples, showed RSD values of <2% reflecting the accuracy and reproducibility of the newly modified resin.</p> </p>     

Liquid-liquid extraction of 233Pa(V) with Aliquat 336</p> </p>

Summary The extraction of protactinium with Aliquat 336 (methyl-tri-caprylyl ammonium chloride) in toluene, cyclohexane and chloroform from HCl, HNO₃, H₂SO₄, HClO₄, HF and mixed HCl-HF media was investigated by radioactive tracer technique. Distribution ratios of protactinium between the aqueous solution and the organic phase were determined as a function of shaking time, concentrations of acid in aqueous solution phase, extractant concentration and type of diluents in the organic phase. Aliquat 336 can almost quantitatively extract protactinium from strong HCl solution. At the same time, small amounts of HF in HCl solutions have a strong effect on Pa distribution.</p> </p>     

Sorption and desorption of UO2 2+, Th4+ and Ru3+ on the synthetic analogue of muscovite</p> </p>

Summary Sorption and desorption of UO₂²⁺, Th⁴⁺ and Ru³⁺ on the synthetic analogue of the mica mineral muscovite has been studied by a batch technique. The synthesized gel was characterized by XRD, EDXRFS, FTIR, TGA and SEM and was found to have a composition K_1.4Al_4.2(Si₆Al₂O₂₀)(OH)₄ ^. 2H₂O. Different parameters like acid concentration, contact time, amount of gel, composition of gel: OPC admixture, effect of temperature, desorption of metal ions from loaded muscovite and effect on crystal morphology due to loading of metal ions were studied. The results has been expressed in terms of distribution coefficient (K_d).</p> </p>     

Removal of radium from sand filters by inorganic acids</p> </p>

Summary Sand filters are used in water treatment stations to remove particulate matter from underground water, where iron and manganese are collected forming thin oxide films. These oxides of iron and manganese adsorb radium from underground water. Radium concentration increases in time on the filters, and consequently the level of radioactivity increases in the station. The removal of adsorbed radium on sand using inorganic acids was studied. Good efficiency of radium removal was obtained by controlling different parameters like temperature, time, pH, addition of competitive cations and anions. It was found that hydrochloric acid is the best for radium removal from sand filters. Maximum removal obtained was about 60% at 5M BaCl₂ and 2M HCl at 50 °C for 180-minute contact time. Kinetic parameters of the removal process were studied and compared with literature data.</p> </p>     

Inorganic ion-exchangers in radioactive waste management</p> </p>

Summary The uptake of indigenously synthesized amorphous stannic and zirconium phosphate was assessed for, one of the important fission fragment, cesium from aqueous solutions using a radiotracer technique. A virtual increase in sorptive concentration (from 1.0 ^. 10^-8 to 1.0 ^. 10^-2 mol ^. dm^-3) and pH (from 2.4 to 10.2) and temperature (from 303 to 333 K) enhanced the uptake of cesium on stannic phosphate. However, the extremely high degree of uptake of cesium on zirconium phosphate was almost unaffected with the dilution beyond 10^-5 mol ^. dm^-3 and pH (i.e., from 2.4 to 10.2) and temperature (from 303 to 323 K). Irreversible uptake occurring for these solids follow the Freundlich adsorption isotherm and the presence of several complexing agents viz., sulphate, phosphate, glycine and EDTA did not affect appreciably the uptake of cesium on zirconium phosphate but it did affect for stannic phosphate system. Both these solids showed good radiation stability towards a 11.1 GBq Ra-Be neutron source having neutron flux ca. 3.2 ^. 10⁶ n ^. cm^{-2 .} s^-1 and associated with a nominalg-dose of ca. 1.72 Gy/h, at least for the uptake of cesium.</p> </p>     

Factors affecting the sorption of Eu(III) on modified silica gel</p> </p>

Summary 8-Hydroxyquinoline in benzene, xylene, chloroform and toluene diluents was used to modify silica gel as a solid phase extractant (SPE) for the sorption of Eu(III) in batch extraction techniques. Influences of solid/liquid ratio, pH, metal ion concentration, particle size and temperature were studied. The optimum initial pH is 4.2, while the maximum sorption capacities for the prepared impregnated resins in benzene, xylene, chloroform and toluene diluents are 18.52, 14.98, 14.79 and 5.94 mg ^. g^-1, respectively. The sorption process is found to be affected by both metal ion concentration and particle size of the impregnated resin. Thermodynamic parameters for the sorption of Eu(III) were determined and the reaction is found to be exothermic and spontaneous with enthalpy-14.23 and-23.71 kJ ^. mol^-1 for benzene and xylene as diluents. Release of the element from the loaded solid particles into 0.01M HNO₃ is@85% and@53% from 8-HQ/benzene/silica gel and 8-HQ/xylene/silica gel.</p> </p>     

Mössbauer study of Fe/S and Fe/O films produced by laser ablation of pyrite and hematite</p> </p>

Summary Pyrite FeS₂ was laser-deposited onto Al substrates at various temperatures, and the M?ssbauer spectra of the films were measured. The yields and the M?ssbauer parameters of FeS₂ and FeS changed depending on the formation temperature, because of the sulfur deficiency in the lattice structures. In addition, hematite Fe₂O₃ was employed as a laser-ablation target, and FeO and Fe₂O₃ were deposited on SiO₂/Si substrates. It was shown that laser-deposition of compounds can produce films that have different chemical species than the laser-evaporated materials.</p> </p>     

Recovery of technetium adsorbed on charcoal</p> </p>

Two methods capable of near complete recovery of technetium adsorbed on charcoal are presented. The first involves liquid extraction of the technetium from the charcoal by hot 4M nitric acid. An average recovery of 98% (n=3) is obtained after three rounds of extraction. The second method involves dry ashing with air in a quartz combustion tube at 400-450 °C. This method yields an average recovery of 96% (n=5). Other thermal methods were attempted, but resulted in reduced recovery and incomplete material balance.</p> </p>     

Electrolytic production of metallic uranium from U3O8 in a 20-kg batch scale reactor</p> </p>

Summary The electrolytic reduction of U₃O₈ powder was carried out using LiCl-Li₂O molten salt in a 20-kg U₃O₈ batch cell to verify the feasibility of the process. As the current passes the cell, the decomposition of Li₂O and the reduction of U₃O₈ occur simultaneously in a cathode assembly and oxygen gas evolvs at the anode. The results from a 20-kg U₃O₈ scale cell were compared with data obtained from a bench scale cell. The results suggest a successful demonstration of this process, exhibiting a reduction conversion of U₃O₈ of more than 99% in a batch.</p> </p>     

Transfer of 226Ra, 85Sr and 137Cs from milk to milk products</p> </p>

Summary Transfer of ²²⁶Ra, ⁸⁵Sr and ¹³⁷Cs from cow and sheep milk to various Syrian dairy products has been evaluated. Dairy products include Kashkivan cheese, braided cheese, Haloom cheese, Sircassian cheese, liquid cheese, native cheese, cottage, thick yogurt, butter and milk cream. The results showed that the percentage of ²²⁶Ra, ⁸⁵Sr and ¹³⁷Cs transferred from cow milk to milk cream (P_t=food processing retention factor′processing efficiency′100%) has reached 32%, 16% and 7%, respectively. Butter and liquid cheese were found to have the lowest percentage of transferred 226Ra, ⁸⁵Sr and ¹³⁷Cs. Most of the obtained P_t values of the studied radionuclides in thick yogurt were relatively low in spite of the high processing efficiencies of thick yogurt. Moreover, the transfer, P_t, of the studied radionuclides from cow milk to the prepared cheese was higher than those values determined for sheep milk. This is due to differences in chemical compositions of each type of milk. On the other hand, the treatment of Native cheese, most commonly consumed cheese in Syria, with different concentrations of NaCl solutions showed that ¹³⁷Cs was completely removed from cheese soaking in 5% NaCl solution (soaking time of 48 hours), while 40% of ²²⁶Ra and 80% of ⁸⁵Sr were also decontaminated using 0-2.5% NaCl solutions and soaking time of 48 hours. Based on the obtained results, industrialization processes of the dairy products that resulted the removal of radionuclides have been identified.</p> </p>     

Cascade ultrafiltering of 210Pb and 210Po in freshwater using a tangential flow filtering system</p> </p>

Summary A rapid method was developed using ultrafilters with a tangential flow filtering system for molecular size separation of naturally occurring ²¹⁰Pb and ²¹⁰Po in a freshwater sample. Generally, ultrafiltering of a large volume water sample for measuring the nuclides was too time consuming and not practical. The tangential flow filtering system made the filtering time short enough to adapt for in-situ ultrafiltering the large volume sample. In this method, a 20 liter water sample was at first passed through the 0.45mm pore size membrane filter immediately after sample collection to obtain suspended particle matter [>0.45mm particulate fraction (PRT)]. Two ultrafilters (Millipore Pellicon 2^ò) were used sequentially. The nuclides in the filtrate were separated into three fractions: high molecular mass (100 kDa-0.45mm; HMM), low molecular mass (10 k-100 kDa; LMM) and ionic (<10 kDa; INC) fractions. It took 80 minutes to process the sample after collection. The cut-off molecular size of each ultrafilter was confirmed by size exclusion chromatographs (SEC) of the LMN and the HMM fractions. Adsorption of the nuclides and organic compounds in the sample onto the ultrafilters was negligibly small. Good reproducibility of the nuclide concentrations in each fraction was confirmed by repeated experiments. The method was successfully applied to obtaine the molecular size distributions of ²¹⁰Pb and ²¹⁰Po in an oligotrophic lake, Lake Towada located in the northern area of Japan.</p> </p>     

Radioiodination of insulin using N-succinimidyl 5-(tributylstannyl)-3-pyridine-carboxylate (SPC) as a bi-functional linker: Synthesis and biodistribution in mice</p> </p>

Summary Insulin receptors are overexpressed on a number of human tumors, leading to significant affinity of insulin to these tumors. It is appealing to receptor-targeted radiotherapy for malignant tumors if insulin is labeled with suitable radionuclide. In this paper, N-succinimidyl 5-(tributylstannyl)-3-pyridinecarboxylate (SPC), a potential bi-functional linker for radioiodination of proteins or peptides, was synthesizedby using 5-bromonicotinic acid as the starting material. Then, with this bi-functional linker, insulin was conjugated with ¹³¹I, and the tissue distribution of the labeled insulin (¹³¹I-SIPC-insulin) in normal mice was investigated. The results showed that insulin ^</span> could be conjugated with¹³¹I using SPC as the linker ^</span> in a labeling yield of40-58%, and with radiochemical purity of more than 98% after purification bySephadex?G-10. Even kept at room temperature for 72 hours, the radiochemical purity of ¹³¹I-SIPC-insulin was still more than 97%, implying that the conjugated insulin was constantly stable in vitro.Meanwhile, in order to evaluate the in vivo stability of the conjugated compounds, insulin was also labeled with ¹³¹I by a direct method using chloramine-T (Ch-T) as the electrophilic agents.Biodistribution of¹³¹I-SIPC-insulinin micesuggested that ¹³¹I could clear rapidly from the blood,mainly excreted by kidney. However, ¹³¹I uptake of mice with¹³¹I-SIPC-insulin in some key organs, especially in thyroid and stomach, were much less (150 or 30 times) than that with the direct labeled insulin (¹³¹I-insulin). Additionally, it was noted that ¹³¹I-SIPC-insulin hasmuch betterinvivo stability than¹³¹I-insulin.</p> </p>