气相色谱法测定溶剂型木器涂料中异佛尔酮含量

建立一种快速测定溶剂型木器涂料中异佛尔酮含量的气相色谱法。样品经乙酸乙酯提取,采用Rtx–1701毛细管色谱柱分离后,以十四烷作内标物,内标法定量。该方法中异佛尔酮质量浓度在10~200 mg/L范围内呈良好的线性关系,相关系数r=0.999 98,方法检出限为10 mg/kg。样品平均加标回收率为92.2%~97.1%,测定结果的相对标准偏差为0.13%~1.25%(n=6)。该方法能有效地对溶剂型木器涂料中异佛尔酮进行定性、定量分析,而且具有简单、快速、准确、检出限低等特点,能满足实验要求。     

液液萃取气相色谱法测定水体中环己酮的含量

建立液液萃取–气相色谱法测定水体中环己酮含量的分析方法。水样用二硫化碳萃取,萃取液经无水硫酸钠脱水后,用气相色谱法测定环己酮的含量。环己酮的质量浓度在0~18.16 mg/L范围内与色谱峰面积线性良好,线性相关系数r=0.999 8。方法检出限为0.010 mg/L,加标回收率为93.3%~95.8%,测定结果的相对标准偏差为2.32%~3.48%(n=6)。该方法预处理简单,检测灵敏度高,可用于水体中环己酮含量的测定。     

非完全汽化气相色谱法测定溶剂型涂料中的微量苯、甲苯、二甲苯

用乙酸乙酯稀释溶剂型涂料样品，在较低的汽化温度下直接进样，溶剂型涂料中未汽化的组分留在汽化室里，而苯、甲苯和二甲苯汽化后进入毛细管，用气相色谱法氢火焰离子化检测器进行检测，与国家标准分析方法进行比较，该法具有操作简单、精密度高等优点。     

气相色谱法同时测定溶剂型胶黏剂中的9种有害物质

建立了利用毛细管柱气相色谱同时测定溶剂型胶黏剂中苯、 甲苯、 对（间）二甲苯、 邻二甲苯、 二氯甲烷、1,2-二氯乙烷、1,1,2-三氯乙烷、三氯乙烯、甲苯二异氰酸酯（TDI）的方法,并对样品中有害物质的分离提取和色谱条件进行了研究.实验结果表明,方法化合物浓度在10~300 μg/mL时,线性相关系数不低于0.999 1,样品加标回收率在91.2%~104.1%之间,相对标准偏差均小于5%,检出限为0.1~3.0 μg/mL.方法不仅回收率高、重现性好,而且简便、快速.     

气相色谱法同时测定溶剂型胶粘剂中苯系物及卤代烃

应用气相色谱法同时测定溶剂型胶粘剂中苯系物及卤代烃的含量。用PEG-20M色谱柱(30m×0.32mm,0.25μm)分离,火焰离子化检测器检测。12种苯系物及卤代烃在一定的质量浓度范围内均与其峰面积呈线性关系,方法的检出限(3S/N)在0.01~0.27g·kg-1之间。加标回收率在81.0%~106%之间,测定值的相对标准偏差(n=6)在1.3%~4.7%之间。     

气相色谱法测定涂料中三种醇类抗冻剂含量

建立了内外墙涂料样品中三种抗冻剂醇类物质气相色谱测定方法。涂料样品经乙醇萃取、离心,上清液进气相色谱氢火焰检测器检测,外标法定量。结果表明,乙二醇、1,2-丙二醇和丙三醇在20~500 mg/L浓度范围内线性关系良好,相关系数均大于0.999,方法检出限在10~20 mg/kg之间,三个添加水平平均回收率(n=6)在87.3%~93.4%之间,相对标准偏差(RSD)为5.0%~6.7%。该方法简单快速、回收率和精密度良好,适用于内外墙涂料中乙二醇、1,2-丙二醇和丙三醇的同时测定。利用气相色谱测定涂料中醇类组分含量,从而可快速鉴定涂料低温稳定性能,达到快速检测筛选的目的。     

顶空-气相色谱/质谱法测定溶剂型木器涂料中7种卤代烃

建立了顶空-气相色谱/质谱(HS-GC/MS)法测定溶剂型木器涂料中卤代烃含量的方法。采用HS-GC/MS测定了二氯甲烷、1,1-二氯乙烷、三氯甲烷、1,1,1-三氯乙烷、四氯化碳、1,2-二氯乙烷、1,1,2-三氯乙烷7种化合物,样品经丙酮稀释,外标法定量。结果表明:7种卤代烃含量在0.05~500 mg/L范围内线性关系良好,相关系数(r2)大于0.994,定量限为0.05~0.2 mg/kg。加标回收率64.4%~107.7%,相对标准偏差为4.1%~11%(n=6)。方法已用于溶剂型木器涂料中卤代烃的定性、定量分析。     

气相色谱法分离和测定溶剂型木器涂料中正丁醇与苯系物

在气相色谱法测定溶剂型木器涂料中正丁醇及苯系物(包括苯、甲苯及二甲苯)时采用了VF-200MS型号的毛细管色谱柱。由于此型号的毛细管柱具有较强极性,不仅能达到正丁醇与苯系物之间的有效而满意的分离,而且还能使苯系物(包括苯、甲苯、乙苯、二甲苯)之间和二甲苯的同分异构体之间的有效分离。测定中采用正戊烷作内标和用火焰离子检测器检测。此方法的检出限(2S/N)在1.7~3.5 ng之间。用一含有正丁醇的硝基漆样品按所提出的方法进行多次重复测定,并在此样品的基础上加入各被测化合物的标准后进行测定,从而对方法的回收率和精密度作了测试,测得其回收率在87.8%~100.0%之间,测定值的相对标准偏差(n=6)均小于2.5%。     

气相色谱法测定柴胡注射液中环己醇

建立了气相色谱法测定柴胡注射液中环己醇的定量分析方法，以正己烷为萃取剂，水蒸汽蒸馏浓缩富集提取液，用PEG－20M柱，氢火焰检测器（FID）检测。结果表明，柴胡注射液中环己醇质量浓度在10.0μg/mL-120.0μg/mL范围内呈良好的线性关系（r=0.998），回收率为92 .3%-95.1%，RSD为1.1%－1.2%。     

Determination of aliphatic amines in water by gas chromatography using headspace solvent microextraction

The possibility of applying headspace microextraction into a single drop for the determination of amines in aqueous solutions is demonstrated. A 1 μl drop of benzyl alcohol containing 2-butanone as an internal standard was suspended from the tip of a micro syringe needle over the headspace of stirred sample solutions for extraction. The drop was then injected directly into a GC. The total chromatographic determination was less than 10 min. Optimization of experimental conditions (sampling time, sampling temperature, stirring rate, ionic strength of the solution, concentration of reagents, time of extraction and organic drop volume) with respect to the extraction efficiency were investigated and the linear range and the precision were also examined. Calibration curves yielded good linearity and concentrations down to 2.5 ng ml⁻¹ were detectable with R.S.D. values ranging from 6.0 to 12.0%. Finally, the method was successfully applied to the extraction and determination of amines in tap and river water samples. This system represents an inexpensive, fast, simple and precise sample cleanup and preconcentration method for the determination of volatile organic compounds at trace levels.     

Determination of thermodynamic properties of macroporous glycidyl methacrylate‐based copolymers by inverse gas chromatography

Macroporous crosslinked poly(glycidyl methacrylate‐co‐ethylene glycol dimethacrylate) (PGME) was synthesized by suspension copolymerization and modified by ring‐opening reaction of the pendant epoxy groups with ethylene diamine (EDA). Inverse gas chromatography (IGC) at infinite dilution was applied to determine the thermodynamic interactions of PGME and modified copolymer, PGME‐en. The specific surface areas of the initial and modified copolymer samples were determined by the BET method, from low‐temperature nitrogen adsorption isotherms. The specific retention volumes, V, of 10 organic compounds of different chemical nature and polarity (nonpolar, donor, or acceptor) were determined in the temperature range 333–413 K. The weight fraction activity coefficients of test sorbates, , and Flory–Huggins interaction parameters, , were calculated and discussed in terms of interactions of sorbates with PGME and PGME‐en. Also, the partial molar free energy, , partial molar heat of mixing, , sorption molar free energy, ΔG, sorption enthalpy ΔH, and sorption entropy, ΔS, were calculated. Glass transitions in PGME and PGME‐en, determined from IGC data, were observed in the temperature range 373–393 K and 363–373 K, respectively. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2524–2533, 2005     

Determination of cholesterol in fat and muscle of pig by HPLC and capillary gas chromatography with solvent venting injection

Two methods for determination of cholesterol in fat and muscle of pig were evaluated: extraction with chloroform:methanol (2:1, v/v) followed by saponification (method 1) and direct saponification (method 2). HPLC and GC were used to determine cholesterol concentrations. GC analysis was performed with a capillary column of 100 μm using a PTV injector in the modes of cold split and solvent venting. Cholesterol was analyzed without derivatization. Both methods of extraction did not present significant differences (p > 0.01). Sample analysis by GC with solvent venting injection and HPLC showed the lowest % r.s.d. but GC in the cold split mode allowed to obtain a shorter analysis time. Cholesterol concentrations obtained by HPLC were not statistically different from the results obtained by GC with solvent venting injection and were slightly lower than those previously reported. Cholesterol concentrations in fat and muscle tissues respectively ranged from 52 to 77 mg/100 g and from 55 to 65 mg/100 g.     

Principal component analysis of polymer–solvent and filler–solvent interactions by inverse gas chromatography

Polymers (polyethylene, polyurethane), silica and modified silicas (modified with: N-2-aminoethyl-3-aminopropyltrimethoxysilane, 3-aminopropyltriethoxysilane, 3-merkaptopropyltrimethoxysilane, triethoxyoctylsilane) were examined by inverse gas chromatography at four different temperatures: 363, 383, 393 and 403 K. The modifiers of silica were applied at five different concentrations. Small amounts of the following test solutes were injected to achieve the infinite dilution conditions: pentane, hexane, heptane, octane, nonane, dichloromethane, chloroform, carbon tetrachloride, and 1,2-dichloroethane.

The retention times for these test solutes were determined and Flory–Huggins parameters were calculated. Values of these physico-chemical parameters characterizing the examined materials were arranged in a matrix form: in the rows the supports and modifiers were enumerated at different temperatures whereas the columns contained the test solutes. The input matrix was subject to principal component analysis after standardization. Three principal components explain more than 93% of the total variance in the data. Four test solutes (hexane, heptane, chloroform and carbon tetrachloride) carry very similar information. Therefore, it is justified to eliminate any three of them from the series of test solutes. Modifiers, supports and various temperatures were classified and different groups were observed according to the dominant interactions. Type of modifier, its content, and temperature can change and shift the properties from the dominant clusters to the neighboring clusters. Unambiguous separation was observed in cases of silica modified with 5 and 10 parts of triethoxyoctylsilane at all examined temperatures.     

顶空进样-气相色谱法检测乳制品中硫氰酸盐的含量

建立了顶空进样气相色谱法测定乳制品中硫氰酸盐含量的方法。乳制品中硫氰酸盐用水提取,然后用乙酸锌溶液沉淀蛋白质,将提取液离心,取上清液加入氯胺T将硫氰酸离子衍生为氯化氰,顶空进样,经BP10(14%氰丙基苯基聚硅氧烷)气相色谱柱分离,电子捕获检测器(ECD)检测,外标法定量,同时对衍生剂用量、顶空加热时间和保温温度进行了优化。结果表明: 硫氰酸盐在0.005～0.1 mg/L内线性关系良好,相关系数(r)为0.997,定量限(以信噪比(S/N)≥10计)为0.1 mg/kg。在1.0、2.0、10.0 mg/kg 3个添加水平下进行了回收率和精密度试验,加标回收率为90.0%～110.0%,相对标准偏差(RSD, n=10)为4.98%～7.89%。该方法操作简便、快速、稳定性好,可用于乳制品中硫氰酸盐的测定,能满足日常检测要求。应用该法对市售的18种乳制品进行了检测,发现所测乳制品皆含有硫氰酸盐,含量大约在0.5～10 mg/kg。     

A multiresidue method for the analysis of pesticide residues in polished rice (Oryza sativa L.) using accelerated solvent extraction and gas chromatography and confirmation by mass spectrometry

An analytical procedure using accelerated solvent extraction and gas chromatography with an electron capture detector has been optimized to simultaneously determine the residue of two insecticides (diazinon and EPN) and one fungicide (isoprothiolane) in polished rice and was confirmed by GC-mass spectrometry. Several parameters, including temperature, pressure, solvent ratio, cell size and cell cycle, were thoroughly investigated to find the optimal extraction conditions. The average recoveries of the three pesticides were between 82.7 and 126.4% at spiking levels of 0.1 and 0.5 ppm. The relative standard deviations were less than 7% for all of the recovery tests. The optimum accelerated solvent extraction operating conditions were 100 degrees C, 1500 atm, acetone-n-hexane (20:80 v/v) as the extraction solvent, two cycles, and a cell size of 33 ml. The total extraction time was approximately 20 min. The optimized procedure has also been applied to the determination of diazinon, isoprothiolane and EPN in real rice samples. In conclusion, accelerated solvent extraction was used for the first time for the analysis of diazinon, isoprothiolane and EPN in polished rice and offers the possibility of a fast and simple process for obtaining a quantitative extraction of the studied pesticides.     

快速溶剂萃取-气相色谱/质谱联用测定塑料桌布中的邻苯二甲酸酯

采用快速溶剂萃取-气相色谱/质谱联用法(ASE-GC/MS)和超声波萃取-气相色谱/质谱联用法(USE-GC/MS)测定了塑料桌布中的邻苯二甲酸酯.结果表明:ASE-GC/MS的测量精度优于USE-GC/MS,后者测量值大约为前者的五分之四;ASE-GC/MS的回收率为89.0%～95.5%,相对标准偏差为4.3%～1...