Poly(anthraquinonyl sulfide) cathode for potassium-ion batteries

Potassium-ion batteries (KIBs) are a promising sustainable energy storage technology due to the high abundance and low cost of potassium. Carbon anode materials for KIBs have seen great successes, but the development of cathode materials is yet to catch up. In this study, poly(anthraquinonyl sulfide) (PAQS) is evaluated as a cathode material for KIBs. It exhibits a high reversible capacity of 200 mAh/g, which is the highest value for a potassium storage cathode material. The cell shows two slopes averaged at 2.1 and 1.6 V vs. K⁺/K. It shows a good cycling performance with the capacity retention of 75% after 50 cycles at a rate of C/10. These preliminary results indicate that PAQS is a promising cathode material for KIBs.     

A hierarchical micro/nanostructured 0.5Li2MnO3·0.5LiMn0.4Ni0.3Co0.3O2 material synthesized by solvothermal route as high rate cathode of lithium ion battery

A hierarchical micro/nanostructured Li-rich layered 0.5Li₂MnO₃·0.5LiMn_0.4Ni_0.3Co_0.3O₂ (H-LMNCO) material is prepared for the first time through the development of a solvothermal method, and served as cathode of lithium ion batteries. Electrochemical tests indicate that the H-LMNCO exhibits both a high reversible capacity and an excellent rate capability. The reversible discharge capacity of the H-LMNCO has been measured as high as 300.1 mAh·g^− 1 at 0.2 C rate. When the rate is increased to 10 C, the discharge capacity could still maintain a high value of 163.3 mAh·g^− 1. The results demonstrate that the developed solvothermal route is a novel synthesis strategy of preparing high rate performance Li-rich layered cathode material for lithium ion batteries.     

A disordered rock-salt Li-excess cathode material with high capacity and substantial oxygen redox activity: Li1.25Nb0.25Mn0.5O2

A disordered rocksalt Li-excess cathode material, Li_1.25Nb_0.25Mn_0.5O₂, was synthesized and investigated. It shows a large initial discharge capacity of 287 mAh g^− 1 in the first cycle, which is much higher than the theoretical capacity of 146 mAh g^− 1 based on the Mn³⁺/Mn⁴⁺ redox reaction. In situ X-ray diffraction (XRD) demonstrates that the compound remains cation-disordered during the first cycle. Electron energy loss spectroscopy (EELS) suggests that Mn and O are likely to both be redox active, resulting in the large reversible capacity. Our results show that Li_1.25Nb_0.25Mn_0.5O₂ is a promising cathode material for high capacity Li-ion batteries and that reversible oxygen redox in the bulk may be a viable way forward to increase the energy density of lithium-ion batteries.     

Designing high-capacity cathode materials for sodium-ion batteries

Na-rich layered oxides as cathode materials for sodium-ion batteries were designed using an electrochemical method based on Li-rich layered oxides. The materials show high specific capacity that can reach 234 mAh/g at a current of 5 mA/g. The energy density of this material (644 Wh/kg) is even higher than those of commercial cathodes for lithium-ion batteries, such as LiFePO₄ and LiMn₂O₄. Kinetic analysis of Na⁺ insertion/extraction into/from the Na-rich layered oxide reveals that the Na⁺ diffusion coefficient is about 10^− 14 cm²/s.     

High-performance Na1.25V3O8 nanosheets for aqueous zinc-ion battery by electrochemical induced de-sodium at high voltage

Aqueous rechargeable zinc-ion batteries (ARZIBs) are expected to replace organic electrolyte batteries owing to its low price, safe and environmentally friendly characteristics. Herein, we fabricated vanadium-based Na_1.25V₃O₈ nanosheets as a cathode material for ARZIBs, which present a high performance by electrochemical de-sodium at high voltage to form Na₂V₆O₁₆ phase in the first cycle: high capacity of 390 mAh/g at 0.1 A/g, high rate performance (162 mAh/g at 10 A/g) and superior cycle stability (179 mAh/g with a high capacity retention of 88.2% of the maximum capacity after 2000 cycles). In addition, the cell exhibits a high energy density of 416.9 Wh/kg at 143.6 W/kg, suggesting great potential of the as-prepared Na_1.25V₃O₈ nanosheets for ARZIBs     

Combustion synthesized LiMnSnO4 cathode for lithium batteries

Novel category LiMnSnO₄ compound was synthesized via. Urea assisted combustion (UAC) method at 800 °C and examined for possible use as cathode material in lithium-ion batteries. The XRD (X-ray diffraction) results of LiMnSnO₄ sample authenticate the orthorhombic crystal structure with high degree of crystallinity. Presence of uniformly distributed nanometric grains (scanning electron microscopy) with preferred local cation environment is evident from FT IR (Fourier transform infra red spectroscopic) and ⁷Li NMR (nuclear magnetic resonance spectroscopy) studies. The charge–discharge behavior of Li/LiMnSnO₄ cells demonstrated a specific capacity of 113 mA h/g, with an excellent capacity retention (95%) and Ah efficiency (>99%). Besides, the internal resistance of the Li/LiMnSnO₄ cell after 30 cycles is negligibly small, thus demonstrating good electronic conductivity and cycling stability, required for any lithium intercalating cathode material.     

Tremella-like molybdenum dioxide consisting of nanosheets as an anode material for lithium ion battery

Tremella-like structured MoO₂ consisting of nanosheets was obtained via a Fe₂O₃-assisted hydrothermal reduction of MoO₃ in ethylenediamine aqueous solution. The as-prepared product was characterized and tested with scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV) and capacity measurement as anode material for lithium ion batteries. This structured MoO₂ shows very high reversible capacity (>600 mA h g⁻¹), good rate capability and cycling performance, presenting potential application as anode material for lithium ion batteries with high rate capability and high capacity.     

Nanocomposite of manganese ferrocyanide and graphene: A promising cathode material for rechargeable lithium ion batteries

A nanocomposite of potassium manganese ferrocyanide and graphene (12% C, 88% K_1.8Mn_1.1Fe(CN)₆∙ 0.27H₂O) was prepared by ball milling of graphene oxide powder and nanoparticles of manganese–iron Prussian Blue. It exhibits enhanced electrochemical performance compared to pure Prussian Blue with a specific capacity of 150 mAhg^− 1 at average 3.8 V vs. Li⁺/Li and a good cyclability. The nanocomposite can be considered as competitive to standard cathode materials of present rechargeable lithium ion batteries like cobalt oxide, iron phosphate or NMC.     

Facile synthesis and long cycle life of SnSb as negative electrode material for Na-ion batteries

We report significant electrochemical performances promoting SnSb as one of the most promising negative electrode material for rechargeable batteries. Appropriately formulated with the carboxymethyl cellulose binder and cycled in fluoroethylene carbonate containing electrolyte, it could sustain a reversible capacity largely exceeding 525 mAh g^− 1 over more than 125 cycles at a rate of C/2 (55 mA/g), with a satisfactory coulombic efficiency of more than 97%. To our knowledge, this is actually the longest cycle life ever reported for an electrode material vs. sodium.     

Partially reduced SnO2 nanoparticles anchored on carbon nanofibers for high performance sodium-ion batteries

One-dimensional (1-D) carbon nanofibers anchored with partially reduced SnO₂ nanoparticles (SnO₂/Sn@C) were successfully synthesized through a simple electrospinning method followed by carbon coating and thermal reduction processes. The partially reduced Sn frameworks, combined with the carbon fibers, provide a more favorable mechanism for sodiation/desodiation than SnO₂. As a result, SnO₂/Sn@C exhibits a high reversible capacity (536 mAh g^− 1 after 50 cycles) and an excellent rate capability (396 mAh g^− 1 even at 2 C rate) when evaluated as an anode material for sodium-ion batteries (SIBs).     

High-capacity LiV3O8 thin-film cathode with a mixed amorphous–nanocrystalline microstructure prepared by RF magnetron sputtering

LiV₃O₈ thin films with a mixed amorphous–nanocrystalline microstructure were deposited on stainless steel substrates using radio-frequency (RF) magnetron sputtering for the first time. The films exhibited good performance as a cathode material for lithium ion batteries. Results indicate that the film electrodes had a smooth surface and consisted mainly of an amorphous structure containing nanocrystalline zones dispersed within it. Depending on its microstructure, the films delivered an initial discharge capacity as high as 382 mAh/g and exhibited good capacity retention, with discharge capacity of 301 mAh/g after 100 cycles representing a loss rate of 0.21% per cycle.     

A Li3V2(PO4)3/C thin film with high rate capability as a cathode material for lithium-ion batteries

A monoclinic lithium vanadium phosphate (Li₃V₂(PO₄)₃) and carbon composite thin film (LVP/C) is prepared via electrostatic spray deposition. The film is studied with X-ray diffraction, scanning and transmission electron microscopy and galvanostatic cell cycling. The LVP/C film is composed of carbon-coated Li₃V₂(PO₄)₃ nanoparticles (50 nm) that are well distributed in a carbon matrix. In the voltage range of 3.0–4.3 V, it exhibits a reversible capacity of 118 mA h g^?1 and good capacity retention at the current rate of 1 C, while delivers 80 mA h g^?1 at 24 C. These results suggest a practical strategy to develop new cathode materials for high power lithium-ion batteries.     

Preparation and electrochemical lithium storage of flower-like spinel Li4Ti5O12 consisting of nanosheets

In this paper, flower-like spinel Li₄Ti₅O₁₂ consisting of nanosheets was synthesized by a hydrothermal process in glycol solution and following calcination. The as-prepared product was characterized by scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction and cyclic voltammetry. The capacity of the sample used as anode material for lithium ion battery was measured. This structured Li₄Ti₅O₁₂ exhibited a high reversible capacity and an excellent rate capability of 165.8 m Ahg⁻¹ at 8 C, indicating potential application for lithium ion batteries with high rate performance and high capacity.     

Phosphatization: A promising approach to enhance the performance of mesoporous TiO2 anode for lithium ion batteries

We report phosphatization is a promising method to enhance the performance of mesoporous TiO₂ anode for lithium ion batteries. The resulting phosphated mesoporous TiO₂ possessed higher reversible capacity and better cycling stability than the pure mesoporous TiO₂. When cycled at 30 mA/g between 3.0 and 1.0 V, the initial capacity of phosphate mesoporous TiO₂ was 249 mA h/g, significantly higher than that of pure mesoporous TiO₂ (204 mA h/g). After 40 cycles, the capacity retention ratio of phosphate mesoporous TiO₂ reached 83.7%, while pure mesoporous TiO₂ had merely a capacity retention ratio of 62.3%. We believe that this phosphatization process could be used to enhance the electrochemical performance of other metal oxides for lithium ion batteries.     

LiMn2O4 hollow nanosphere electrode material with excellent cycling reversibility and rate capability

Lithium-rich Li_1.05Mn₂O₄ hollow nanospheres have been successfully prepared by air-calcining lithiated MnO₂ precursor at a low temperature of 550 °C, which was synthesized by chemical lithiation of hollow MnO₂ nanospheres with LiI at 70 °C for 12 h. The lithium-rich Li_1.05Mn₂O₄ hollow nanospheres exhibit an excellent cycling stability and rate capability as a cathode material for rechargeable lithium batteries: it maintains 90% of its initial capacity after 500 cycles, and keeps 70% of the reversible capacity at 0.1 C rat, even at 15 C rate.     

NiCo2O4 nanosheets supported on Ni foam for rechargeable nonaqueous sodium–air batteries

NiCo₂O₄ nanosheets supported on Ni foam were synthesized by a solvothermal method. A composite of NiCo₂O₄ nanosheets/Ni as a carbon-free and binder-free air cathode exhibited an initial discharge capacity of 1762 mAh g^− 1 with a low polarization of 0.96 V at 20 mA g^− 1 for sodium–air batteries. Na₂O₂ nanosheets were firstly observed as the discharged product in sodium–air battery. High electrocatalytic activity of NiCo₂O₄ nanosheets/Ni made it a promising air electrode for rechargeable sodium–air batteries.     

Room temperature Na/S batteries with sulfur composite cathode materials

Sodium/sulfur (Na/S) batteries were assembled with a sodium metal anode, liquid electrolyte and a sulfur composite cathode. Their electrochemical characteristics have been investigated at room temperature. Their charge/discharge curves indicate that sodium can reversibly react with sulfur at room temperature. The specific capacity of the sulfur composite cathode material in the first cycle was initially about 655 mA h g⁻¹ and stayed at about 500 mA h g⁻¹ up to the 18th cycle with about 100% charge/discharge efficiency.     

High capacity and excellent cyclability of vanadium (IV) oxide in lithium battery applications

A VO₂ · 0.43H₂O powder with a flaky particle morphology was synthesized via a hydrothermal reduction method. It was characterized by scanning electron microscopy, electron energy loss spectroscopy, and thermogravimetric analysis. As an electrode material for rechargeable lithium batteries, it was used both as a cathode versus lithium anode and as an anode versus LiCoO₂, LiFePO₄ or LiNi_0.5Mn_1.5O₄ cathode. The VO₂ · 0.43H₂O electrode exhibits an extraordinary superiority with high capacity (160 mAh g^?1), high energy efficiency (95%), excellent cyclability (142.5 mAh g^?1 after 500 cycles) and rate capability (100 mAh g^?1 at 10 C-rate).     

Si–AB5 composites as anode materials for lithium ion batteries

The Si–AB₅ (MmNi_3.6Co_0.7Al_0.3Mn_0.4 alloy) composites with a high tap density as anode materials for lithium-ion batteries were synthesized by ball-milling. Si nanoparticles are distributed homogeneously on the surface of the AB₅ matrix. The electrochemical performance of the Si–AB₅ composites as a function of Si content was investigated. It is demonstrated that the Si–AB₅ composite delivers a larger reversible capacity and better cycle ability because the inactive AB₅ alloy can accommodate the large volume changes of Si nanoparticles distributed on the surface of the Si–AB₅ composite during cycling. In particular, the Si–AB₅ composite containing 20 wt% Si with the high tap density of 2.8 g/cm³ obtained after ball-milling for 11 h exhibits an initial and maximum reversible (charge) capacity of 370 and 385 mAh/g. The high capacity retention can be achieved after 50 cycles in the potential range from 0.02 to 1.5 V.     

Enhanced electrochemical performance of carbon-coated TiO2 nanobarbed fibers as anode material for lithium-ion batteries

We report the electrochemical performance of carbon-coated TiO₂ nanobarbed fibers (TiO₂@C NBFs) as anode material for lithium-ion batteries. The TiO₂@C NBFs are composed of TiO₂ nanorods grown on TiO₂ nanofibers as a core, coated with a carbon shell. These nanostructures form a conductive network showing high capacity and C-rate performance due to fast lithium-ion diffusion and effective electron transfer. The TiO₂@C NBFs show a specific reversible capacity of approximately 170 mAh g^− 1 after 200 cycles at a 0.5 A g^− 1 current density, and exhibit a discharge rate capability of 4 A g^− 1 while retaining a capacity of about 70 mAh g^− 1. The uniformly coated amorphous carbon layer plays an important role to improve the electrical conductivity during the lithiation–delithiation process.