Synthesis of195mPt radiolabeled cisdiammine (glycolato) platinum (II) of high radionuclidic purity

An experimental method is described for the synthesis of^195mPt-radiolabeled cis-diammine (glycolato) platinum (II) (254-S). Ten mg of 95% enriched¹⁹⁴Pt was irradiated for 75 h in the hydraulic conveyer of KUR at a thermal neutron flux of ca. 8.15×10¹³ n·cm^–2·s^–1, and the^195mPt-radiolabeled 254-S was synthesized and purified using HPLC (column: Dichrosorb Diol, elution: 80% CH₃CN). The chemical yield was approximately 45%, with chemical purity greater than 98.4%. The radionuclidic purity was nearly 100% and the specific activity, 7.2 MBq·mg^–1 254-S.     

An approach to study ‘molecular rocket’ reaction using metallocene-cyclodextrin inclusion compounds

An experimental method is described for the synthesis of^195mPt-radiolabeled (–)-(R)-2-aminomethylpyrrolidine (1,1-cyclobutanedicarboxylato)-2-platinum (II) (DWA2114R). An amount of 10 mg of 95% enriched¹⁹⁴Pt was irradiated for 75 h in the hydraulic conveyer of the KUR at a thermal neutron flux of approximately 8.1×10¹³ n.cm^–2.sec^–1 and the^195mPt-radiolabeled DWA2114R was purified using HPLC. The chemical yield is higher than 65%, its chemical purity is greater than 99.2%, the radiochemical purity is nearly 100%, and the specific activity is 6.7 MBq. mg^–1 DWA2114R.     

Preparation and Application of a Novel Core-Shell Organic Nanoparticle as a Fluorescence Probe in the Determination of Nucleic Acids

A novel type of core-shell organic nanoparticles (pyrene/poly-acrylic acid; PAA) has been prepared by precipitation polymerization under ultrasonic irradiation. It was characterized by transmission electron microscopy (TEM) and fluorescence lifetime. The lifetime is about 5µs, which is much longer than conventional organic dyes fluorescence lifetime. As the surface of the core-shell organic nanoparticles is covered with abundant carboxylic groups, the nanoparticles are water-soluble, stable and biocompatible. At pH 6.4, maximum fluorescence is produced, with the maximum excitation and emission wavelengths of 338nm and 397nm, respectively. Under optimum conditions, the calibration graphs are linear over the range of 4.0×10^–51.0×10^–2mgmL^–1 for calf thymus DNA (ct-DNA) and 2.0×10^–41.0×10^–2mgmL^–1 for fish sperm DNA (fs-DNA). The detection limits were 3.6×10^–5mgmL^–1 and 1.4×10^–4mgmL^–1 for ct-DNA and fs-DNA, respectively. The method was applied to the determination of ct-DNA and fs-DNA in synthetic samples and the results were satisfactory. The method is sensitive, stable, rapid and tolerant towards most interfering substances.     

Technetium-99m generator based on 12-molybdocerate —99Mo precipitate as column matrix

The preparation of insoluble 12-molybdocerate(IV) from⁹⁹Mo of low specific activity, produced by thermal neutron irradiation of MoO₃, is described. Samples of the material are dried at 50, 100 and 200°C and used as column matrices from which the generated^99mTc activity is periodically eluted with saline solution or saline solution containing 5·10^–5M K₂CrO₄ as an oxidant. The elution yields of^99mTc are high and reproducible (95–81%) with radionuclidic purity 99.98%. Both chemical and radiochemical purity (as TcO ₄ ^– ) of the eluates decrease with increasing drying temperature of the column matrix. Using chromated saline solution as eluent improves the radiochemical purity of the^99mTc eluate.     

Determination of particle-bound trace metals in high purity hydrogen chloride

Summary Two analytical procedures for the determination of particle-bound trace metals in high purity hydrogen chloride are described. Polycarbonate membrane filters with a pore diameter of 0.05 m were used for sampling. Membrane filtration with subsequent instrumental neutron activation analysis (using irradiation with a thermal neutron flux of 10¹³ n cm^–2 s^–1 and irradiation and measurement times of either 20 min) has made it possible to determine the elements Br, Mg, Mn, Na, Sb, Sn, Te, Ti and Zn. For a gas sample volume of 500 l the detection limits determined are in the range of 0.86 ng l^–1 for Zn to 0.30 pg l^–1 for Mn.The elements Cr, Cu, Fe, Mn and Ni were determined by membrane filtration with subsequent graphite tube furnace atomic absorption spectrometry. In this case the detection limits achieved are (for a gas sample volume of 500 l and 4 ml digestion solution) between 8.4 pg l^–1 for Fe and 2.1 pg l^–1 for Cu. The analytical procedures were applied for the characterisation of high purity hydrogen chloride, which is used in the manufacture of highly integrated semiconductor components, by trace analysis, both directly on the gas cylinder and at the 'point of use after passing through the supply system. A review of the status of element determination in high purity process gases is given.

---

Bestimmung von partikelgebundenen Metallspuren in hochreinem Chlorwasserstoff

     

Spectrophotometric determination of ciprofloxacin in pure form and in tablets through charge-transfer complexation reactions

Three simple, quick and sensitive spectrophotometric methods are described for the determination of ciprofloxacin. The methods are based on the reaction of this drug as ann-electron donor with 2,3-dichloro-5,6-dicyano-p-benzoquinone (DDQ), 7,7,8,8,-tetracyanoquinodimethane (TCNQ) andp-chloranil (CL) as -acceptors to give highly coloured complex species. The coloured products are quantitated spectrophotometrically at 460, 843 and 550 nm for DDQ, TCNQ and CL, respectively. Optimization of the different experimental conditions is described. Beer's law is obeyed in the concentration ranges 5–50, 1.5–15 and 20–200 g ml^–1 ciprofloxacin, but the concentration ranges for best accuracy are 10–48, 2.5–15 and 35– 195 g ml^–1 of drug for DDQ, TCNQ and CL, respectively. The relative standard deviations are less than 1.5%. Applications of the suggested methods to ciprofloxacin tablets are presented and compared with the USP method. The stability constants of the 11 DDQ and CL complexes were 1.086 × 10⁴ and 2.581 × 10⁴ lmol^–1, respectively, whereas for the 12 TCNQ complex it was 3.62 × 10⁸1. mol^–1.     

Electrostriction of polymethylmethacrylates

Electrostriction of tactic polymethylmethacrylates in response to step-on and step-offdc-fields was investigated in the field strength range from 1 to 5 MV m^–1 at room temperature; one example of electrostriction under sinusoidal field is given.Three principal retardation time regions were found: ₁=1.5 s, ₂=30 s, and ₃=140 s, each field strength independent. The retardation strengths belonging to these electrostrictive processes depend on tacticity.The low frequency limit of the electrostrictive volume compliance for the investigated PMMA is _a =–1.2×10^–15 m² V ^–2 for atactic, _S =–2.3×10^–14 m² V ^–2 for syndiotactic, and _i=–4.5 × 10^–14 m² V ^–2 for isotactic PMMA.Herrn Prof. Dr. F. H. Müller gewidmet.     

Mutual diffusion coefficients of aqueous ZnSO4 at 25°C

Diffusion coefficients of the system ZnSO₄–H₂O at 25°C have been measured using Rayleigh optics from 0.004 to 3.33m. The results appear to extrapolate with reasonable agreement to the data of Harned and Hudson at very low concentration. The diffusion coefficients decrease from 0.8486×10^–5 at 0m to 0.2813×10^–5 cm²-sec^–1 at 3.33m. Densities were measured over the concentration range 0.10 to 3.60m and combined with the data of Geffcken and of Gibson to obtain an analytical expression for density over the concentration range 0m3.6.     

Statistical analysis of the results of99mTc-MDP quality control

The methods used for control of radiochemical purity of^99mTc-MDP are presented. TLC method on silica gel, developed with methanol and acetone (11 v/v), was convenient for determination of^99mTcO ₄ ^– with the content of 2.6±1.2%. The reliable results on detection of^99mTc hydrolyzate (2.2±1.3%) and for another^99mTc-MDP complex (13.2±2.8%) were obtained by application of ITLC (SA), developed with Sn-MDP. By Sephadex G-25 column chromatography (1.5 cm×5 cm) the separation of^99mTcO ₄ ^– was not achieved. The range of normal^99mTc-MDP biodistribution values in the organs of experimental animals have been determined. The mean value of bone distribution was 8.4±1.13%/g, in muscles 0.071±0.033%/g, while uptake in liver and kidneys was below 5%. Chi-square test and P show that the results on biodistribution of^99mTc-MDP in liver, bones and muscles are arranged around their mean values, which is statistically allowed.     

Gas Chromatographic Determination of Sulfur Mustard and Lewisite in Community Air

A gas chromatographic procedure is developed for the determination of ,-dichlorodiethylsulfide (yperite, sulfur mustard) and -chlorovinyldichloroarsine (lewisite) in the working area and community air at a level defined by the hygienic regulations for community air (2 × 10^–6 and 4 × 10^–6 mg/m³ for sulfur mustard and lewisite, respectively) and at the maximum permissible level for a working area (2 × 10^–4 mg/m³). The procedure for the determination of sulfur mustard is based on the trapping of the analyte from air with Silochrom S-120 impregnated with Apiezon L with further extraction by a 1 : 1 acetone–hexane mixture, the evaporation of the extract to a small residual volume, and chromatography with an electron capture detector. The procedure for the determination of -chlorovinyldichloroarsine (lewisite) involves the absorption of the analyte with a 2.2% solution of triethanolamine in 0.1 M hydrochloric acid, the conversion of lewisite to acetylene by treating the trap contents with 30% alkali solution, and the chromatography of the vapor phase using a flame ionization detector. The error of the determination is no more than ±23 rel %. The analysis takes 1.5 h.     

Enrichment of sea-salt aerosols in short-lived222Rn daughter products-role of marine Fe/III/ hydroxide colloid

The interaction of short-lived Rn-daughter products /SLDP/, viz.²¹⁴Pb and²¹⁴Bi dissolved in sea-water with Fe/III/ hydroxide colloids followed by flotation of combined Fe-SLDP particles at the sea-air interface subsequently generating marine aerosols enriched in²¹⁴Bi and²¹⁴Pb have been studied under laboratory conditions. Rate constants for attachment of²¹⁴Bi and²¹⁴Pb to dispersed Fe/III/ colloids in the sea water are found to be 3.7×10^–4 min^–1 litre [g/Fe/]^–1 and 2.4×10^–4 min^–1 litre [g/Fe/]^–1, resp., /20°C/ over the concentration range of iron /III/ from 8 to 120 g liter^–1. The suggested mechanism of colloid flotation and aerosol generation might be responsible for some peculiarities of SLDP distribution in the lower marine atmosphere.     

The New Fluorescence Enhancement System Eu<Superscript>3+</Superscript>-ARADE-HMTM-Al<Superscript>3+</Superscript> and its Analytical Application

A new bis-Schiff base ligand, N,N-bis-(4-N-aminothiourea-2-amylidene)-4,4-diaminodiphenyl ether (ARADE), was synthesized. Its complex with Eu³⁺ in DMF emits the intrinsic fluorescence of Eu³⁺. The fluorescence intensity of the Eu³⁺-ARADE system was enhanced about 60-fold by the addition of hexamethylene tetramine (HMTM) and potash alum. This is a new fluorescence enhancement phenomenon. The excitation and emission wavelengths are 375nm and 615nm, respectively. Under optimal conditions, the fluorescence intensities vary linearly with the concentration of Eu³⁺ in the range of 7.8×10^–9–1.75×10^–5mol·L^–1 with a detection limit of 5.2×10^–9mol·L^–1, or with the concentration of Al³⁺ in the range of 3.1×10^–7–9.7×10^–5mol·L^–1 with a detection limit of 2.7×10^–7mol·L^–1. The interferences of some rare earth metals and other inorganic ions were described. This method was applied to the determination of Eu³⁺ in high purity yttrium oxide and the analysis of Al³⁺ in alloy steel standard samples. The mechanism of fluorescence enhancement was also studied.     

Solvent effect and temperature dependence in the interaction of singlet oxygen with α-phenyl-N-tert-butyl nitrone

The solvent effect on the quenching of singlet oxygen by -phenyl-N-tert-butyl-nitrone /PBN/ has been investigated by laser flash photolysis technique registrating luminescence kinetics of¹O₂. The values of the rate constant /k_q/ of the quenching were at 293 K: /9.0±0.4/×10⁶, /4.4±0.3/×10⁶ and /18.3±0.5/×10^{6 –}M^–1 s^–1 in toluene, chloroform and acetonitrile, respectively. The rate constant for the chemical interaction between¹O₂ and PBN, was k_r<1×10⁵ M^–1 s^–1k_q independently of the solvent. At temperatures between 223 and 293 K in toluene E_q=0.4±0.4 kJ mol^–1.     

Preparation of Sn-β-alanine: A new freeze-dried kit to be labelled with99mTc for liver scintigraphy

Sn-alanine kits were prepared in lyophilized form containing 7.02·10^–2 M -alanine and 5.5·10^–4M stannous chloride dihydrate. The optimal pH value of the preparation was found to be equal to 4.3–5.1. The radiochemical purity and the stability of^99mTc-alanine were assessed by gel filtration column scanning techniques (GCS) and thin layer chromatography, and the labelling yield of the complex was higher than 95%. The organ distribution data in mice showed that more than 90% of the injected dose had been accumulated in the liver. However, a negligible amount of radioactivity was detected in the non-target organs. The stability of^99mTc-alanine was followed for 5 hours and the Sn-alanine kit was stable for at least 3 months.     

Simultaneous determination of lead-210, gross beta and gross alpha activities of air filters by pulse shape discrimination liquid scintillation counting

A chemical procedure for transferring deposited solid matter from a cellulose filter into the liquid scintillation cocktail has been described. The influence of chemical and color quenching on alpha and beta detection efficiency, as well as on misclassification of beta and alpha pulses was corrected by an external standard method. Under the chosen pulse shape discrimination level (PSD), the alpha and beta detection efficiencies were above 85% and spillovers of alpha and beta pulses were below 10% and 2% respectively. Determination limits for samples containing up to 200 mg of mineral matter were 0.015 mBq m^–3 for alpha, 0.055 mBq.m^–3 for²¹⁰Pb and 0.055 mBq.m^–3 for beta activity (counting time 12000 s and volume of filtered air 1000 m³). The method has been applied for routine monitoring of²¹⁰Pb as well as for gross alpha and beta activities of longer-living radionuclides (T_1/2.>11 hrs) in suspended air matter.     

Simultaneous determination of zinc,iron and chlorides in radiopharmaceutical gallium /67Ga/ citrate injections by FSDP or DP polarography

A method for simultaneous determination of traces of zinc, iron, and chloride ions by fast scan or ordinary differential pulse polarography has been proposed. The method is especially suited to check the purity of radiopharmaceutical gallium /⁶⁷Ga/ citrate injections. The interference of citrate ions was eliminated by using a complex-forming base electrolyte containing triethanolamine and ammonia. The relative standard deviation of the determination of iron, zinc, and Cl^– ions in the range of 0.05–1.00 g of Fe or Zn and 3–25 g of Cl^– per ml solution was found to be 5–10%.     

Sorption kinetics of tributyltin on Elbe river biofilms

For the first time detailed sorption kinetics of tributyltin on native Elbe river biofilms are presented. For this purpose a modified annular rotating continuous flow reactor has been used to develop a reproducible biofilm. Important parameters, such as flow rates, sheer forces, and nutrient concentrations could be varied independently and adjusted to natural conditions. Time-resolved sorption kinetics have been carried out with tributyltin, the most toxic compound in many antifouling paints. The highest sorption rates of tributyltin were observed during the first 0–10 min (0.60±0.05 g Sn m^–2min^–1) than they decreased to a value of 0.10±0.10 g Sn m^–2min^–1 (10–90 min) and increased to a value of 0.20±0.05 g Sn m^–2min^–1 (90–120 min).     

Electrical properties of poly(bis(β-phenoxyethoxy)phosphazene) and its complexes

Electrical and dielectrical properties of poly(bis(-phenoxyethoxy)phosphazene) (I) and its complexes with various content ratios of AgSO₃CF₃ to monomeric unit (0.25/1 (II) and 0.5/1 (III) in molar ratio) were investigated.Dc conductivity of respective samples at 18 °C were 6.1×10^–12, 4.4×10^–9, and 7.1×10^–8 S/m.Dc conduction was considered to be due to ion hopping. Charge mobility ranged from 3×10^–12 to 6× 10^–11 m²/Vs depending on the applied field in sample II. In sample I, a tan peak was found which can be ascribed to molecular relaxation of main chains. The peak vanished upon introducing AgSO₃ CF₃. Temperature dependence of total conductivity ( _T ) measured byac method in the temperature range between –150 °C and 50 °C showed several peaks at the temperatures corresponding to the peak temperatures of tan. Total conductivities of respective samples at 100 kHz were 4.9×10^–7 (69 °C), 1.7×10^–4 (45 °C), and 1.5×10^–4(40°C)S/m.     

FIA Amperometric Determination of Molybdenum(VI) Based on the Catalysis of the Hydrogen Peroxide-Iodide Reaction

An analytical approach to FIA amperometric determination of molybdenum based on the well-known catalytic reaction involving the oxidation of iodide by hydrogen peroxide is proposed. The indirect method involves measurements of triiodide at a glassy carbon electrode polarised at +0.2V in a flow-through configuration. The limit of detection was found to be 6×10^–9molL^–1, and the dynamic concentration range was established as 1×10^–7molL^–1 to 5×10^–5molL^–1. The repeatability of measurements was determined as 2.1% (n = 20). The amount of Mo in a steel sample was determined after removing the additive interference from iron by using fluoride ions, and the results were in good agreement with the certified value. Interference of other metallic ions is addressed.     

A Highly Sensitive and Selective Assay for Cysteine Using the Chemiluminescence Reaction of Luminol and Hydrogen Peroxide

A very simple, highly sensitive and selective chemiluminescence (CL) method was established for the determination of cysteine. This method is based on the fact that the CL reaction of luminol and hydrogen peroxide can be greatly enhanced by cysteine. The CL intensities at maximum light emission were linearly correlated with the concentration of cysteine over the range of 2.0×10^–8–6.0×10^–6molL^–1 with a detection limit of 7.5×10^–9molL^–1. The relative standard deviation was 1.7% for the determination of 1.0×10^–7molL^–1 cysteine (n=9). The feasibility of utilizing the proposed method for the determination of total concentration of cysteine in human serum was examined.