Determination of inorganic arsenic(III) in ground water using hydride generation coupled to ICP-AES (HG-ICP-AES) under variable sodium boron hydride (NaBH4) concentrations

The determination of inorganic arsenic species in ground water matrices using hydride generation coupled online to ICP-AES (HG-ICP-AES) is suggested on the fact that the As(III)-species shows significantly higher signal intensities at low sodium boron hydride (NaBH₄) concentrations than the As(V)-species. The sodium boron hydride concentration used for the determination of As(III) without any considerable interferences of As(V) was at 13.2 mmol/L NaBH₄ (0.05 wt/v%), whereas the concentration for the total As determination was at 158.4 mmol/L NaBH₄ (0.6 wt/v%). The interferences of As(V) during the As(III) measurements were very small: at concentrations below 100 μg/L of total arsenic, the interferences of As(V) were smaller than 2%. An amount of As(III) higher than 10% of the total As amount could be determined exactly and reliably. The total amount of arsenic is measured after reducing the sample with 20 mmol/L L-cysteine (C₃H₇NO₂S). Finally, the amount of the As(V)-species is calculated by the difference between the As(III)-species and the total arsenic. Therefore, this analytical method requires the absence of organic arsenic species, but if they still appear, they could be frozen out with liquid nitrogen after the hydride generation system. The linearity of calibration reaches from 2 μg/L up to 1000 μg/L with a detection limit routinely of about 1 μg/L for each species. The advantages of this method in comparison to AAS measurements are the higher extent of the linear calibration range (3 orders of magnitude) and a higher sensitivity. Additional merits of the method developed are easy handling and high sampling rates.     

Determination of selenium by atomic absorption spectrometry with miniaturized suction-flow hydride generation and on-line removal of interferences

On-line removal of transition metal interferences in microscale suction-flow hydride generation atomic absorption spectrometry is described for the determination of selenium at μg l^?1 levels. A mini-column of a chelating resin with iminodiacetate groups is used. Selenium in solutions containing ? 2.5 mg of copper or nickel was determined at a rate of 30 samples per hour; the detection limit was 0.1 ng of selenium. The relative standard deviation for ten replicate measurements of 5 ng of selenium was 3.8%. The method was applied successfully to the determination of selenium in standard copper alloys and nickel sponge.     

开叉毛细管HG-FAAS测定地质样品中的锑、铋

氢化物发生原子吸收法(HG-FAAS)广泛应用于冶金、地质、环境、医药和食品分析等领域中。研究表明,氢化物发生法的检出限、测定精度以及干扰等情况与原子化器和氢化物发生器的结构以及传输过程有关[1]。郭小伟等[2-4]研制了用于火焰原子吸收光谱分析的双毛细管喷雾器,并利用其测     

Preconcentration and in-situ photoreduction of trace selenium using TiO2 nanoparticles, followed by its determination by slurry photochemical vapor generation atomic fluorescence spectrometry

We have developed a method for the determination of trace levels of total selenium in water samples. It integrates preconcentration, in-situ photoreduction and slurry photochemical vapor generation using TiO₂ nanoparticles, and the determination of total selenium by AFS. The Se(IV) and Se(VI) species were adsorbed on a slurry of TiO₂ nanoparticles which then were exposed to UV irradiation in the presence of formic acid to form volatile selenium species. The detection limits were improved 17-fold compared to hydride generation and 56-fold compared to photochemical vapor generation, both without any preconcentration. No significant difference was found in the limits of detection (LODs) for Se(IV) and Se(VI). The LOD is as low as 0.8 ng L^?1, the precision is better than 4.5 % (at a level of 0.1 μg L^?1 of selenium). The method gave good recoveries when applied to the determination of total selenium in a certified tissue reference material (DORM-3) and in spiked drinking water and wastewater samples containing high concentrations of transition and noble metal ions. It also excels by very low LODs, a significant enhancement of sample throughput, reduced reagent consumption and sample loss, and minimal interference by transition and noble metal ions.

Negative thermal ionization mass spectrometry of selenium part 3.* Selenium trace determination in food samples

Summary Selenium traces are analysed in different animal tissue samples with isotope dilution mass spectrometry using the formation of negative Se^– thermal ions (NTI-IDMS) for isotope ratio measurements. An enriched⁸²Se spike is applied for the isotope dilution technique. After decomposition of the food samples with a HNO₃/HCIO₄ mixture selenium is separated by the formation of SeH₂ using a hydride generation system which is normally applied for atomic absorption spectrometry. Selenium hydride is absorbed in a cone. HNO₃ solution, from which sample mass spectrometric determinations are carried out. The recovery of selenium for the total sample treatment has been determined with a⁷⁵Se tracer to be about 62%. The precision of the IDMS method in the concentration range of 0.1–10 g/g lies between 1.8% and 4.1 %. The IDMS results agree well with the certified values of the analysed standard reference materials. A comparison of these results with those achieved by an isotope dilution method, using the formation of piazselenol and gas-chromatographic separation (GC-IDMS), and by hydride generation atomic absorption spectrometry (HGAAS) is given. Whereas the NTI-IDMS and GC-IDMS results are in very good agreement, HGAAS can be affected by interferences.

---

Negative Thermionen-Massenspektrometrie von Selen Teil 3. Selenspurenbestimmung in Lebensmittelproben

---

Part 2: see [131

---

Dedicated to Prof. Dr. G. Tölg on the occasion of his 60th birthday     

Simultaneous determination of trace arsenic, antimony, bismuth and selenium in biological samples by hydride generation-four-channel atomic fluorescence spectrometry

A new and sample technique for the simultaneous determination of trace arsenic, antimony, bismuth and selenium in biologic samples by hydride generation-four-channel nondispersive atomic fluorescence spectrometry was development. The conditions of instrumentation and hydride generation of arsenic, antimony, bismuth and selenium were optimized. For reducing hexavalent Se to the tetravalent state was to heat the sample with 6 mol l⁻¹ HCl, and then pre-reducing pentavalent As and Sb to the trivalent state was achieved by the addition of 0.05 mol l⁻¹ thiourea. The interferences of coexisting ions were evaluated. Under optimal conditions, the detection limits for As, Sb, Bi and Se were determined to be 0.03, 0.04, 0.04 and 0.03 ng ml⁻¹, respectively. The precision for seven replicate determinations at the 5 ng ml⁻¹ of As, Sb, Bi and Se were 0.9, 1.2, 1.3 and 1.5% (R.S.D.), respectively. The proposed method was successfully applied to the simultaneous determination of As, Sb, Bi and Se in a series of Chinese certified biological reference materials using simple aqueous standard calibration technique, the results obtained are in good agreement with the certified values.     

Study of the effects of elements that form volatile hydrides on the determination of selenium by hydride generation atomic absorption spectrometry

Summary A study has been made of possible interferences upon the determination of selenium by hydride generation atomic absorption spectrometry (HGAAS), due to the presence of other hydride forming elements such as As, Ge, Bi, Te, Sn and Sb, and to a volatile element such as Hg. The interfering effects of these cations were determined at several concentration levels using sodium borohydride as the reductant and a commercially available semi-automatic system for the generation and the flameless combustion of the hydrides. It has been demonstrated that the determination of selenium by HGAAS is relatively free from interferences with regard to other elements that form volatile hydrides, except for tin and bismuth that strongly interfere.

---

Einfluß von flüchtige Hydride bildenden Elementen auf die Selenbestimmung als Hydrid durch AAS

Zusammenfassung Bei der AAS-Bestimmung von Selen als Hydrid wurde der Einfluß der hydridbildenden Elemente As, Ge, Bi, Te, Sn, Sb sowie auch des flüchtigen Elements Hg untersucht. Die Untersuchungen wurden bei verschiedenen Konzentrationen mit Natriumborhydrid als Reduktionsmittel durchgeführt. Dabei wurde ein handelsübliches halbautomatisches System zur Erzeugung und flammenlosen Verbrennung der Hydride benutzt. Es zeigte sich, daß die Selenbestimmung bis auf die stark störenden Elemente Sn und Bi relativ frei von Beeinflussungen ist.

     

Evaluation of continuous hydride generation combined with helium and argon microwave induced plasmas using a surfatron for atomic emission spectrometric determination of arsenic,antimony and selenium

The direct coupling of continuous hydride generation with both Ar and He microwave induced plasmas (MIP) sustained in a surfatron has been optimized for the simultaneous determination of arsenic, antimony and selenium with atomic emission spectrometry. While a discharge tube of quartz was found suitable for the Ar plasma, the use of an Al₂O₃ tube led to improved performance of the He plasma. The He MIP was found to be less tolerant to the introduction of hydrogen than the Ar MIP, and correspondingly the hydride generation should be operated at a lower flow rate of 0.5% NaBH₄ solution. The introduction of the H₂O vapour produced during hydride generation into both discharges was found to greatly decrease the sensitivities and to degrade the measurement precision. It could be effectively removed with trapping by concentrated H₂SO₄. The detection limits (3σ) for As, Sb and Se are 1, 0.4 and 1 ng ml⁻¹ with the Ar MIP, and 2, 0.3 and 6 ng ml⁻¹ with the He MIP, respectively. The calibration curves are linear over three decades of concentration. The mutual interferences from As(III), Sb(III), Se(IV), Bi(III) and Sn(IV) were found to be negligible at interferent concentrations below 1 μg ml⁻¹ and in most cases the tolerable interferent concentrations are up to 20 μg ml⁻¹. The proposed method has been applied to the determination of As, Sb and Se in tea samples at μg g⁻¹ levels.     

Comparison of four microwave digestion methods for the determination of selenium in fish tissue by using hydride generation atomic absorption spectrometry

Four microwave digestion methods of fish tissue for selenium determination by hydride generation atomic absorption spectrometry were compared, in which potassium hexacyanoferrate(III) was chosen as a masking agent for eliminating matrix interferences. The results showed that the methods employing HNO(3)/H(2)O(2), HNO(3)/K(2)S(2)O(8)/H(2)O(2) and HNO(3)/H(3)PO(4)/H(2)O(2) digestion media were unreliable. However, the decomposition using the digestion media of HNO(3)/H(2)SO(4)/H(2)O(2) enabled adequate digestion of fish tissue and retention of selenium in a state amenable for determination. Therefore, the digestion procedures with HNO(3)/H(2)SO(4)/H(2)O(2) media are proposed for the determination of selenium in fish tissue by hydride generation atomic absorption spectrometry. The recoveries of the spiked samples investigated ranged from 90 to 102%. The result obtained from analyzing the NIES CRM No. 6 mussel was in good agreement with the reference value (reference value: 1.5 mug/g; found: 1.45 +/- 0.05 mug/g). The limit of detection for selenium was 0.03 mug/g dry mass for a 100 mg sample. The contents of selenium in local fish species investigated ranged from 0.49 to 2.90 mug/g, and the relative standard deviation for the determination of selenium was less than 8%.     

Determination of different oxidation states of arsenic and selenium by inductively coupled plasma-atomic emission spectrometry with ion chromatography

Recent regulation in Japan requires more sensitive trace analysis methods for the determination of arsenic and selenium and their oxidation states As(III) and (V), Se(IV) and (VI). The hydride generation (HG) technique is usually used in combination with AAS and ICP-AES to increase sensitivity. However, hydrochloric acid is mostly used to acidify the sample solution in HG. Isobaric interferences due to chlorine-related species cause mass spectral problems when the same solution is used for the determination of these elements by ICP-MS. In this study, different oxidation states of As and Se were determined by coupling ion chromatography (IC) to an ICP-AES instrument. An HG technique was used to introduce test samples into the ICP. Nitric acid was employed to acidify the samples for HG. The concentrations of acid and base were kept as low as possible to reduce contamination. The formation of As and Se hydrides could be achieved without HCl, if the concentrations of acid and alkaline solutions were optimized. However, HCl was necessary for additional reduction of Se(VI) to Se(IV).     

Determination of different oxidation states of arsenic and selenium by inductively coupled plasma-atomic emission spectrometry with ion chromatography

Recent regulation in Japan requires more sensitive trace analysis methods for the determination of arsenic and selenium and their oxidation states As(III) and (V), Se(IV) and (VI). The hydride generation (HG) technique is usually used in combination with AAS and ICP-AES to increase sensitivity. However, hydrochloric acid is mostly used to acidify the sample solution in HG. Isobaric interferences due to chlorine-related species cause mass spectral problems when the same solution is used for the determination of these elements by ICP-MS. In this study, different oxidation states of As and Se were determined by coupling ion chromatography (IC) to an ICP-AES instrument. An HG technique was used to introduce test samples into the ICP. Nitric acid was employed to acidify the samples for HG. The concentrations of acid and base were kept as low as possible to reduce contamination. The formation of As and Se hydrides could be achieved without HCl, if the concentrations of acid and alkaline solutions were optimized. However, HCl was necessary for additional reduction of Se(VI) to Se(IV).     

Determination of selenium(IV) and other forms of selenium dissolved in sea water by anion-exchange resin loaded with sulfonic acid derivative of bismuthiol-II and hydride generation atomic-absorption spectrometry

Summary A sulfonic acid derivative of bismuthiol-II (bisIIS) was synthesized from 4-hydrazinobenzene sulfonic acid and carbon disulfide. Selenium(IV) was adsorbed selectively and quantitatively on the anion-exchange resin loaded with bis-IIS. Selenium adsorbed on the resin was eluted by the use of penicillamine and determined by hydride generation atomic absorption spectrometry (hydride generation/AAS). Selenium(VI) and other forms of selenium, which were not adsorbed onto the resin, were collected on the resin after digestion with nitric acid followed by reduction with hydrochloric acid. Separative preconcentration of selenium(IV), selenium(VI) and other forms of selenium in 0.5 mol/l sodium chloride could be carried out successfully by the proposed procedures. However, in the case of estuarial sea water containing a large quantity of organic substances, selenium(IV) could not be separated, because organic substances interfered with the reduction of selenium(VI) to selenium(IV) by the use of hydrochloric acid. Selenium(IV) and total amount of selenium(VI) and other forms of selenium dissolved in polluted sea water samples were determined by the proposed procedures.

---

Bestimmung von Selen (IV) und anderen in Meereswasser gelösten Selenformen mit Hilfe eines mit dem Sulfonsäurederivat von Bismuthiol-II beladenen Anionenaustauschers und der Hydrid-AAS

     

Studies in hydride generation atomic fluorescence determination of selenium and tellurium. Part 2 — effect of thiourea and thiols

In determination of selenium and tellurium by continuous flow hydride generation atomic fluorescence spectrometry, the effect of thiourea and thiols was investigated in view of their potential to achieve mild reaction conditions and as masking agents of interference from foreign elements. The effect of thiourea and thiols was first tested in the absence of interfering species and using different addition modes to reaction system. In the absence of interfering species, thiols negatively influenced the hydride evolution of both selenium and tellurium and, in general, they did not produce the desired effects. Thiourea was well tolerated in the determination of both elements by appropriate choice of experimental conditions. Possible mechanisms producing the depressive effect of thiourea and thiols were also investigated and are discussed later. Compromise reaction conditions were identified by using on-line addition of a neutral thiourea solution to acidified sample, combined with KI addition to NaBH₄. Mild reaction conditions can be achieved by decreasing the NaBH₄ concentration but at the expense of a reduced linear dynamic range. In the presence of foreign elements, thiourea allowed good control of interferences generated by Cu(II), Co(II), Ni(II), Au(III), Ag(I) and Bi(III). Tolerance limits could be improved by factors in the range of 7–2000, for both selenium and tellurium determination. The method has been successfully applied in the determination of traces of tellurium and selenium in copper, lead and molybdenum ores, stainless steel and pure copper metal without any additional steps other than sample dissolution.     

Determination of Antimony in Brass by On-line Hydride Generation Atomic Fluorescence Spectrometry Alkaline Solution

The hydride generation(HG) technique combined with atomic spectrometry as a detection system has become one of the most powerful analytical tools for the determination of elements, such as As, Sb, Bi, Se, Te,Ge, Sn and Pb. Normally, the hydride is generated by the reaction between an acidic sample solution with tetrahydroborate. However, when some inorganic ions such as the transition metal ions are present in the reaction matrix, interference arise. Some approaches for minimizing the interference have been suggested, including the addition of various reagents such as thiourea and iron(III) solution. Interfering metals can also be removed by precipitation. The procedure involved filtration before the solution was acidified. In order to reduce the steps of the process, hydride generation from alkaline solution was described for the determination of selenium in copper and nickel materials.     

电感耦合等离子体质谱法测定西红柿中微量元素

采用带六极杆碰撞反应池（CCT）的电感耦合等离子体质谱法（ICP-MS）直接测定了蔬菜样品中微量和痕量金属元素。在碰撞反应池中引入He／H2（93／7）混合气，有效地消除了分子离子（ArCl^-、ArAr^＋等）对痕量砷、硒测定的干扰。比较了原子吸收光谱法和原子荧光法测定结果，两种方法获得的结果基本一致。     

Atomic-absorption spectrochemical analysis for ultratrace elements in geological materials by hydride-forming techniques: Selenium

A method based on hydride generation for the AAS determination of selenium at nanogram levels in geological materials is described. The sample is decomposed by aqua regia attack in a sealed Teflon bomb. After treatment with hydrochloric acid, selenium is converted into hydrogen selenide by reaction with sodium borohydride and determined by AAS. Matrix interference effects have been investigated, but though they are rarely significant, the standard-additions method is recommended. The absolute sensitivity of the method is about 2.0 ng of Se (in 10 ml of solution). Detection limits of about 5-10 ng in a 1.0-g sample have been achieved with the use of "Suprapure" reagents. The selenium content of some USGS, CRPG and ANRT reference samples is reported.     

Determination of Bismuth in Geological Materials by Flow Injection Hydride Generation Atomic Absorption Spectrometry

Abstract

Flow injection analysis (FIA) has been applied to sample introduction in conjunction with automated hydride generation and AAS techniques for the determination of Bi in rock samples. The powdered rock sample is digested with a mixture of hydrofluoric, perchloric, and nitric acids. The evolved hydride is carried through to a heated quartz tube by a stream of argon, and the atomic absorption of Bi is measured at 223.2 nm.

Thiosemicarbazide and 1,10 - phenanthroline are used as masking agents to control interferences from Cu and Ni. The method permits the accurate determination of Bi in geological materials at levels as low as 10 ppb with an analysis rate of more than 50 digested samples per hour. Bi values on 13 international geological reference samples are reported.     

Non-chromatographic hydride generation atomic spectrometric techniques for the speciation analysis of arsenic,antimony, selenium,and tellurium in water samples—a review

Hydride generation (HG) coupled with AAS, ICP–AES, and AFS techniques for the speciation analysis of As, Sb, Se, and Te in environmental water samples is reviewed. Careful control of experimental conditions, offline/online sample pretreatment methods employing batch, continuous and flow-injection techniques, and cryogenic trapping of hydrides enable the determination of various species of hydride-forming elements without the use of chromatographic separation. Other non-chromatographic approaches include solvent extraction, ion exchange, and selective retention by microorganisms. Sample pretreatment, pH dependency of HG, and control of NaBH₄/HCl concentration facilitate the determination of As(III), As(V), monomethylarsonate (MMA), and dimethylarsinate (DMA) species. Inorganic species of arsenic are dominant in terrestrial waters, whereas inorganic and methylated species are reported in seawater. Selenium and tellurium speciation analysis is based on the hydrides generation only from the tetravalent state. Se(IV) and Se(VI) are the inorganic selenium species mostly reported in environmental samples, whereas speciation of tellurium is rarely reported. Antimony speciation analysis is based on the slow kinetics of hydride formation from the pentavalent state and is mainly reported in seawater samples.     

Interferences by transition metals and their elimination by cyanide as a complexing agent in the determination of arsenic using continuous flow HG-ICP-AES

The interfering effects of various foreign ions on the determination of arsenic were studied by hydride generation inductively coupled plasma atomic emission spectrometry (HG-ICP-AES). There were serious inhibiting interferences by Cu, Pb, Co, Au, Pd and Ni. However, by using cyanide as a complexing agent these interferences could be completely eliminated over a wide range of interferent concentration. The optimum chemical parameters for continuous arsine generation were studied. A major advantage of this technique is that it only needs low acid concentrations and produces less hazardous waste. Sensivity, selectivity and accuracy of the determination of arsenic by HG-ICP-AES were investigated. The detection limit (in 1 mol/l HCl medium) for arsenic(III) was 0.82 ng/ml. The relative standard deviation for ten determinations of a solution containing 50 ng/ml arsenic was 1.3%.     

Brauchbarkeit von Mehrelementstandards zur Kalibrierung bei der atomabsorptionsspektroskopischen Wasseranalyse

Zusammenfassung Die Untersuchungen zeigen, daß bei der Bestimmung von Ionen der Elemente Cd, Cr, Cu, Fe, Mn, Pb und Zn mit Hilfe der flammenlosen AAS gegenseitige Störungen auftreten, die durch Zusatz von Salpetersäure verringert, bzw. in einigen Fällen beseitigt werden können. Unter der Bedingung der geringsten gegenseitigen Beeinflussung wurden diese Ionen zu einem Mehrelementstandard kombiniert. Am Beispiel von Wasseranalysen wurde nachgewiesen, daß ein derartiger Mehrelementstandard zur Kalibrierung des Gerätes geeignet ist. Damit können die Bestimmungen mit Hilfe einer Eichkurve bzw. eines Umrechnungsfaktors vorgenommen werden. Die Anwendung des aufwendigen Verfahrens der Standard-Additions-Methode entfällt.

---

Use of multielement standards for calibration in water analysis by AAS

Summary Studies have shown that the determination of metal ions like Cd, Cr, Cu, Fe, Mn, Pb, and Zn by means of flameless AAS is a major problem, because of interference of these metal ions with each other. We found that addition of nitric acid helps in eliminating such interferences partially or in some cases completely. By maintaining proper conditions where such influences are minimum, one can combine these metal ions to a multielement standard. By the example of water analysis by flameless AAS, it is shown that such a multielement standard is suitable for the calibration of the instrument. The determination of metal ions can thus be carried out using either calibration curves or conversion factors and avoiding the tedious standard addition method.