Synthesis and characterization of arylenevinylenearylene–naphthalene diimide copolymers as acceptor in all–polymer solar cells

Two n‐type conjugated D‐A copolymers, P(TVT‐NDI) and P(FVF‐NDI) with thienylene‐vinylene‐thienylene (TVT) or furanylene‐vinylene‐furanylene (FVF) as donor (D) units and naphthalene diimide (NDI) as the acceptor (A) units, were synthesized by the Stille coupling copolymerization. The two polymers possess good solubility, high thermal stability, and broad absorption bands with absorption edges at 866 nm for P(TVT‐NDI) and 886 nm for P(FVF‐NDI) . The LUMO energy levels of P(TVT‐NDI) and P(FVF‐NDI) are ?3.80 eV and ?3.76 eV respectively, so the two polymers are suitable for the application as acceptor in blending with most polymer donor in PSCs based on the energy level matching point of view. All polymer solar cells (all‐PSCs) were fabricated with P(TVT‐NDI) or P(FVF‐NDI) as acceptor and medium bandgap polymer J51 as donor for investigating the photovoltaic performance of the two n‐type conjugated polymer acceptors. And higher power conversion efficiency of 6.43% for P(TVT‐NDI) and 5.21% for P(FVF‐NDI) was obtained. The results indicate that arylenevinylenearylene–naphthalene diimide copolymer are promising polymer acceptor for all–PSCs. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1757–1764     

Side chain engineering of naphthalene diimide–bithiophene‐based polymer acceptors in all‐polymer solar cells

Two novel polymeric acceptors based on naphthalene diimide (NDI) and 2.2′‐bithiophene, named as P(NDI2THD‐T2) and P(NDI2TOD‐T2), were designed and synthesized for all polymer solar cells application. The structural and electronic properties of the two acceptors were modulated through side‐chain engineering of the NDI units. The optoelectronic properties of the polymers and the morphologies of the blend films composed of the polymer acceptors and a donor polymer PTB7‐Th were systemically investigated. With thiophene groups introduced into the side chains of the NDI units, both polymers showed wider absorption from 350 nm to 900 nm, compared with the reference polymer acceptor of N2200. No redshift of absorption spectra from solutions to films indicated reduced aggregation of the polymers due to the steric hindrance effect of thiophene rings in the side chains. The photovoltaic performance were characterized for devices in a configuration of ITO/PEDOT:PSS/PTB7‐Th:acceptors/2,9‐bis(3‐(dimethylamino)propyl)anthra[2,1,9‐def:6,5,10‐def]diisoquinoline‐1,3,8,10(2H,9H)‐tetraone (PDIN)/Al. With the addition of diphenyl ether as an additive, the power conversion efficiencies (PCEs) of 2.73% and 4.75% for P(NDI2THD‐T2) and P(NDI2TOD‐T2) based devices were achieved, respectively. The latter showed improved J_sc, Fill Factor (FF), and PCE compared with N2200 based devices. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3679–3689     

Synthesis of bistriphenylamine‐ and benzodithiophene‐based random conjugated polymers for organic photovoltaic applications

In this study, donor–acceptor random polymers containing benzotriazole acceptor and bistriphenylamine and benzodithiophene donors, P1 and P2 , were successfully synthesized by Stille coupling polymerization. The effect of bistriphenylamine moiety and thiophene π‐conjugated linker on electrochemical, spectroelectrochemical, and optical behaviors of the polymers were investigated. Optoelectronic properties and photovoltaic performance of the polymers were examined under the illumination of AM 1.5G, 100 mW cm^?2. The polymers were characterized by cyclic voltammetry, UV‐Vis‐NIR absorption spectroscopy, gel permeation chromatography. HOMO/LUMO energy levels of P1 and P2 were calculated as ?5.47 eV/–3.41 eV and ?5.43 eV/–3.27 eV, respectively. Bulk heterojunction type solar cells were constructed using blends of the polymers (donor) and [6,6]‐phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) (acceptor). Photovoltaic studies showed that the highest power conversion efficiency of these photovoltaic devices were recorded as 3.50% with open circuit voltage; 0.79 V, short circuit current; 9.45 mA cm^?2, fill factor; 0.53 for P1 :PC₇₁BM (1:2, w/w) in 3% o‐dichlorobenzene (o‐DCB) solution and 3.15% with open circuit voltage; 0.75 V, short circuit current; 8.59 mA cm^?2, fill factor; 0.49 for P2 :PC₇₁BM (1:2, w/w) in 2% chlorobenzene (CB) solution. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3705–3715     

Direct arylation synthesis of thienoisoindigo‐based low‐band‐gap polymer from asymmetric donor–acceptor monomer

Thienoisoindigo (TIG) moiety has been paid numerous attentions as an excellent acceptor building block in low‐band‐gap polymers. Herein, a new TIG‐dithiophene alternating copolymer (PTIG2T) was successfully synthesized from an asymmetric TIG‐based donor–acceptor (D‐A) monomer via the self‐condensation‐type direct arylation polymerization. PTIG2T exhibited the light absorption over 1000 nm owing to the intramolecular charge transfer in the thin film state, which corresponded to an optical band gap of 1.24 eV. The HOMO and LUMO levels of PTIG2T were determined to be −5.08 and −3.60 eV, respectively. Furthermore, the organic photovoltaic (OPV) with a PTIG2T/PC₆₁BM active layer achieved a power conversion efficiency (PCE) of 3.19%, which is one of the highest PEC achieved by OPVs with TIG‐based materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 430–436     

Novel two‐dimensional donor–acceptor conjugated polymers containing quinoxaline units: Synthesis,characterization, and photovoltaic properties

Novel two‐dimensional donor–acceptor (D–A) structured conjugated polymers, P1–P4, were designed and synthesized by introducing electron‐deficient quinoxaline as core and electron‐rich alkoxyl‐phenylenevinylene in side chains and p‐phenylenevinylene, triphenylamine, or thiophene in main chain. Benefited from the D–A structures, the polymers possess low bandgaps of 1.75 eV, 1.86 eV, 1.59 eV, and 1.58 eV for P1, P2, P3, and P4, respectively, and show broad absorption band in the visible region: the shorter wavelength absorption peak at ～400 nm ascribed to the conjugated side chains and the longer wavelength absorption peak between 500 nm and 750 nm belonging to the absorption of the conjugated main chains. Especially, the absorption band of P4 film covers the whole visible range from 300 nm to 784 nm. The power conversion efficiencies of the polymer solar cells based on P1–P4 as donor and PCBM as acceptor are 0.029%, 0.14%, 0.46%, and 0.57%, respectively, under the illumination of AM 1.5, 100 mW/cm². The polymers with the low bandgap and broad absorption band are promising photovoltaic materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4038–4049, 2008     

Conjugated polymers based on 1,8‐naphthalene monoimide with high electron mobility

1,4,8,9‐Naphthalene diimides (NDIs) with strong electron accepting ability and high stability are excellent building blocks for semiconductor polymers. However, 1,8‐naphthalene monoimide (NMI) with similar structure and energy levels as that of NDI has never been used to construct conjugated polymers because of synthetic difficulty. Herein, 3,6‐dibromo‐NMI (DBNMI) with bulky alkyl groups was obtained effectively in a four‐step synthesis, and three donor‐acceptor (D‐A) type conjugated polymers based on NMI were firstly prepared. These polymers have strong absorption in the range of 300–600 nm, low LUMO level of 3.68 eV, and moderate bandgaps of 2.18 eV. Space charge limiting current measurements indicate these polymers are typical electron transporting materials, and the highest electron mobility is up to 5.8 × 10⁻³ cm² V⁻¹ s⁻¹, which is close to the star acceptor based on NDI (N2200, 5.0 × 10⁻³ cm² V⁻¹ s⁻¹). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 276–281     

Diketopyrrolopyrrole‐based acceptor–acceptor conjugated polymers: The importance of comonomer on their charge transportation nature

Besides the donor–acceptor (D–A) type, acceptor–acceptor (A–A) polymers are another class of important alternative conjugated copolymers, but have been less studied in the past. In this study, two kinds of A–A polymers, P1 and P2 , have been designed and synthesized based on diketopyrrolopyrrole in combination with the second electron‐deficient unit, perylenediimide or thieno[3,4‐c]pyrrole‐4,6‐dione. UV–vis absorption spectroscopy revealed that these two kinds of polymers have a band gap of 1.28–1.33 eV. Their highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels are around ?5.6 and ?4.0 eV for P1 polymers, whereas ?5.4 and ?3.7 eV for P2 polymers, respectively. Density functional theory study disclosed that P1 backbone is in a vastly twisting state, whereas that of P2 is completely planar. Furthermore, organic field‐effect transistor devices were fabricated using these two kinds of polymers as the active material. Of interest, the devices based on P1 polymers displayed n‐channel behaviors with an electron mobility in the order of 10^?4 cm² V^?1 s^?1. In contrast, the P2 ‐based devices exhibited only p‐channel charge transportation characteristics with a hole mobility in the order of 10^?3 cm² V^?1 s^?1. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2356–2366     

Synthesis and properties of nitrogen‐linked poly(2,7‐carbazole)s as hole‐transport material for organic light emitting diodes

A novel class of carbazole polymers, nitrogen‐linked poly(2,7‐carbazole)s, was synthesized by polycondensation between two bifunctional monomers using the palladium‐catalyzed amination reaction. The polymers were characterized by ¹H NMR, Infrared, Gel permeation chromatography, and MALDI‐TOF MS and it was revealed that the combination of the monomer structures is important for producing high molecular weight polymers. Thermal analysis indicated a good thermal stability with high glass transition temperatures, e.g., 138 °C for the higher molecular weight polymer P2 . To pursue the application possibilities of these polymers, their optical properties and energy levels were investigated by UV‐Vis absorption and fluorescence spectra as well as their electrochemical characteristics. Although the blue light emission was indeed observed for all polymers in solution, the quantum yields were very low and the solid films were not fluorescent. On the other hand, the HOMO levels of the polymers estimated from the onset potentials for the first oxidation in the solid thin films were relatively high in the range of ?5.12 to ?5.20 eV. Therefore, light emitting diodes employing these polymers as a hole‐transport layer and iridium(III) complex as a triplet emitter were fabricated. The device of the nitrogen‐linked poly(2,7‐carbazole) P3 with p,p′‐biphenyl spacer, which has a higher HOMO level and a higher molecular weight, showed a much better performance than the device of P2 with m‐phenylene spacer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3880–3891, 2009     

Toward low‐band gap dithienophosphole copolymers for an application in organic solar cells

Two functionalized dithieno[3,2‐b:2′,3′‐d]phospholes with solubilizing groups have been synthesized that allow for the generation of a series of π‐conjugated AB‐ and ABC‐copolymers. The polymers obtained show notable optoelectronic properties with red‐shifted absorption and emission in the orange to red section of the optical solar spectrum. Although combination of dithienophosphole units with fluorene building blocks gives access to processable polymers with band gaps between 2.2 and 2.3 eV in solution and 2.0 eV in the solid state, an ABC copolymer based on dithienophosphole, fluorene, and bis(thienyl)benzothiadiazole units was found to not only exhibit a suitable band gap for solar cell applications (solution: 2.0 eV; solid state: 1.7 eV) but also showed good solubility as well as good electron transfer properties in the presence of fullerene (C₆₀). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8179–8190, 2008     

Synthesis,characterization, and photovoltaic properties of dithienylbenzobisazole‐dithienylsilole copolymers

Three conjugated polymers comprised of dioctyl‐dithieno‐[2,3‐b:2',3'‐d]silole and a donor‐acceptor‐donor triad of either cis‐benzbisoxazole, trans‐benzobisoxazole or trans‐benzobisthiazole were synthesized via the Stille cross‐coupling reaction. The impact of varying the heteroatoms and/or the location within the benzobisazole moiety on the optical and electronic properties of the resulting polymers was evaluated via cyclic voltammetry and UV‐Visible spectroscopy. All of the polymers have similar optical band‐gaps of ～1.9 eV and highest occupied molecular orbital levels of ? 5.2 eV. However, the lowest unoccupied molecular orbitals (LUMO) ranged from ? 3.0 to ? 3.2 eV. Interestingly, when the polymers were used as donor materials in bulk‐heterojunction photovoltaic cells with PC₇₁BM as the electron‐acceptor, the benzobisoxazole‐based polymers gave slightly better results than the benzobisthiazole‐containing polymers with power conversion efficiencies up to 3.5%. These results indicate that benzobisoxazoles are promising materials for use in OPVs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1533–1540     

Dithienylmethanone‐Based Cross‐Conjugated Polymer Semiconductors: Synthesis,Characterization, and Application in Field‐Effect Transistors

Herein, we report the synthesis, characterization, and field‐effect properties of two cross‐conjugated dithienylmethanone (DMO)‐based alternating polymers, namely, PDMO‐S and PDMO‐Se . Both polymers possess high thermal stability, good solubility, and broad absorption spectra. Their electrochemical properties were investigated using cyclic voltammetry, indicating that PDMO‐Se has higher HOMO/LUMO energy levels of −5.49/−3.49 eV than −5.57/−3.58 eV of PDMO‐S . The two polymers exhibited promising charge transport properties with the highest hole mobility of 0.12 cm² V⁻¹ s⁻¹ for PDMO‐S and 0.025 cm² V⁻¹ s⁻¹ for PDMO‐Se . AFM and 2D‐GIXRD analyses demonstrated that the PDMO‐S formed lamellar, edge‐on packing thin film with close π‐π stacking. These findings suggest that cross‐conjugated polymers might be potential semiconducting materials for low‐cost and flexible organic electronics. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1012–1019     

Tuning the frontier molecular orbital energy levels of n‐type conjugated copolymers by using angular‐shaped naphthalene tetracarboxylic diimides,and their use in all‐polymer solar cells with high open‐circuit voltages

An angular‐shaped naphthalene tetracarboxylic diimide (NDI) was designed and synthesized as a new building block for n‐type conjugated polymers to tune their energy levels. Three n‐type copolymers incorporating this angular‐shaped NDI as the acceptor moiety were obtained by Stille coupling reactions and had number average molecular weights of 18.7–73.0 kDa. All‐polymer bulk‐heterojunction solar cells made from blends of these polymers with poly(3‐hexylthiophene) gave a power conversion efficiency up to 0.32% and exhibited an open‐circuit voltage (V_oc) up to 0.94 V due to their relative high‐lying lowest unoccupied molecular orbital energy levels. The high V_oc of 0.94 V is higher than that of solar cells based on linear‐shaped NDI‐containing polymers (<0.6 V). The results indicate that the angular‐shaped NDI is a promising building block for constructing nonfullerene polymer acceptors for solar cells with high open‐circuit voltages. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Homoconjugation in poly(phenylene methylene)s: A case study of non‐π‐conjugated polymers with unexpected fluorescent properties

Poly(phenylene methylene) (PPM) exhibits pronounced blue fluorescence in solutions as well as in the solid state despite its non‐π‐conjugated nature. Optical spectroscopy was used to explore the characteristics and the physical origin of its unexpected optical properties, namely absorption in the 350–450 nm and photoluminescence in the 400–600 nm spectral regions. It is shown that PPM possesses two discrete optically active species, and a relatively long photoluminescence lifetime (>8 ns) in the solid‐state. Given the evidence reported herein, π‐stacking and aggregation/crystallization, as well as the formation of anthracene‐related impurities, are excluded as the probable origins of the optical properties. Instead there is sufficient evidence that PPM supports homoconjugation, that is: π‐orbital overlap across adjacent repeat units enabled by particular chain conformation(s), which is confirmed by DFT calculations. Furthermore, poly(2‐methylphenylene methylene) and poly(2,4,6‐trimethylphenylene methylene) – two derivatives of PPM – were synthesized and found to exhibit comparable spectroscopic properties, confirming the generality of the findings reported for PPM. Cyclic voltammetry measurements revealed the HOMO–LUMO gap to be 3.2–3.3 eV for all three polymers. This study illustrates a new approach to the design of light‐emitting polymers possessing hitherto unknown optical properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 707–720     

Pyrrolo[3,4‐c]pyrrole‐1,3‐dione‐based large band gap polymers containing benzodithiophene derivatives for highly efficient simple structured polymer solar cells

Pyrrolo[3,4‐c]pyrrole‐1,3(2H,5H)‐dione (DPPD)‐based large band gap polymers, P(BDT‐TDPPDT) and P(BDTT‐TDPPDT), are prepared by copolymerizing electron‐rich 4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene (BDT) or 4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene (BDTT) unit with novel electron deficient 2,5‐dioctyl‐4,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,3(2H,5H)‐dione (TDPPDT) unit. The absorption bands of polymers P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) cover the region from 300 to 600 nm with an optical band gap of 2.11 eV and 2.04 eV, respectively. The electrochemical study illustrates that the highest occupied/lowest unoccupied molecular orbital energy levels of P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) are ?5.39 eV/?3.28 eV and ?5.44 eV/?3.40 eV, respectively. The single layer polymer solar cell (PSC) fabricated with a device structure of ITO/PEDOT:PSS/P(BDT‐TDPPDT) or P(BDTT‐TDPPDT):PC70BM+DIO/Al offers a maximum power conversion efficiency (PCE) of 6.74% and 6.57%, respectively. The high photovoltaic parameters such as fill factor (～72%), open circuit voltage (V_oc, ～0.90 V), incident photon to collected electron efficiency (～76%), and PCE obtained for the PSCs made from polymers P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) make them as promising large band gap polymeric candidates for PSC application. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3564–3574     

Synthesis and properties of mono‐ and di‐fluoro‐substituted 2,3‐didodecylquinoxaline‐based polymers for polymer solar cells

We synthesized two new alternating polymers, namely P(Tt‐FQx) and P(Tt‐DFQx) , incorporating electron rich tri‐thiophene and electron deficient 6‐fluoroquinoxaline or 6,7‐difluoroquinoxaline derivatives. Both polymers P(Tt‐FQx) and P(Tt‐DFQx) exhibited high thermal stabilities and the estimated 5% weight loss temperatures are 425 and 460 °C, respectively. Polymers P(Tt‐FQx) and P(Tt‐DFQx) displayed intense absorption band between 450 and 700 nm with an optical band gap (E_g) of 1.78 and 1.80 eV, respectively. The determined highest occupied/lowest unoccupied molecular orbital's (HOMO/LUMO) of P(Tt‐DFQx) (?5.48 eV/?3.68 eV) are slightly deeper than those of P(Tt‐FQx) ( ?5.32 eV/?3.54 eV). The polymer solar cells fabricated with a device structure of ITO/PEDOT:PSS/ P(Tt‐FQx) or P(Tt‐DFQx) :PC₇₀BM (1:1.5 wt %) + 3 vol % DIO/Al offered a maximum power conversion efficiency (PCE) of 3.65% with an open‐circuit voltage (V_oc) of 0.59 V, a short‐circuit current (J_sc) of 10.65 mA/cm² and fill factor (FF) of 59% for P(Tt‐FQx) ‐based device and a PCE of 4.36% with an V_oc of 0.69 V, a J_sc of 9.92 mA/cm², and FF of 63% for P(Tt‐DFQx) ‐based device. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 545–552     

Perylene diimide copolymers with dithienothiophene and dithienopyrrole: Use in n‐channel and ambipolar field‐effect transistors

Solution‐processable polymers consisting of perylene diimide (PDI) acceptor moieties alternating with dithienothiophene (DTT), N‐dodecyl‐dithienopyrrole (DTP), or oligomers of these donor groups have been synthesized. We have, in addition to varying the donor, varied the N,N′ substituents of the PDIs. The thermal, optical, electrochemical, and charge‐transport properties of the polymers have been investigated. The polymers show broad absorption extending from 300 to 1000 nm with optical band gaps as low as 1.2 eV; the band gap decreases with increasing the conjugation length of donor block, or by replacement of DTT by DTP. The electron affinities of the polymers, estimated from electrochemical data, range from ?3.87 to ?4.01 eV and are slightly affected by the specific choice of donor moiety, while the estimated ionization potentials (?5.31 to ?5.92 eV) are more sensitive to the choice of donor. Bottom‐gate top‐contact organic field‐effect transistors based on the polymers generally exhibit n‐channel behavior with electron mobilities as high as 1.7 × 10^–2 cm²/V/s and on/off ratios as high as 10⁶; one PDI‐DTP polymer is an ambipolar transport material with electron mobility of 4 × 10^–4 cm²/V/s and hole mobility of 4 × 10^–5 cm²/V/s in air. There is considerable variation in the charge transport properties of the polymers with the chemical structures. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Design,synthesis, photophysical,and electrochemical properties of DCM‐based conjugated polymers for light‐emitting devices

A series of conjugated hyperbranched polymers, hyperbranched copolymers, and linear polymers containing 2‐pyran‐4‐ylidenemalononitrile (acceptor) and triphenylamine/fluorene (donor) units were synthesized and characterized by FTIR, ¹H NMR, thermogravimetric analyses, differential scanning calorimetry, gel permeation chromatography, UV–visible, photoluminescence, and cyclic voltammetry measurements. All the polymers show red‐light emission in the range of 566–656 nm both in solution and in solid state. The quantum efficiency of the polymers was in the range of 56–82%. Among the six polymers synthesized, only polymers containing fluorene units show T_g and polymers based on triphenylamine not exhibit T_g. The band gap of these polymers were found to be reasonably low; hyperbranched copolymer containing fluorene unit shows lowest band gap of 2.18 eV due to the stabilization of LUMO energy level by the electron withdrawing ? CN groups. The thermal and solubility behavior of the polymers were found to be good. All the EL spectra of the devices (indium‐tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/polymer/2,9‐dimethyl‐4,7‐diphenyl‐1,10‐phenanthroline/tris(8‐hydroxyquinoline)aluminum)/LiF/Al) show red‐light emission, and the device fabricated with P3 and P4 shows maximum luminance and luminous efficiency of 4104 cd m^?2 and 0.55 cd Å^?1 and 3696 cd m^?2 and 0.47 cd Å^?1, respectively, indicates that they had the best carrier balance. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and optoelectronic properties of luminescent poly(p‐phenylenevinylene) derivatives containing electron‐transporting 1,3,4‐oxadiazole groups

Three random copolymers ( P1–P3 ) comprising phenylenevinylene and electron‐transporting aromatic 1,3,4‐oxadiazole segments (11, 18, 28 mol %, respectively) were prepared by Gilch polymerization to investigate the influence of oxadiazole content on their photophysical, electrochemical, and electroluminescent properties. For comparative study, homopolymer poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐p‐phenylenevinylene] ( P0 ) was also prepared by the same process. The polymers ( P0–P3 ) are soluble in common organic solvents and thermally stable up to 410 °C under a nitrogen atmosphere. Their optical properties were investigated by absorption and photoluminescence spectroscopy. The optical results reveal that the aromatic 1,3,4‐oxadiazole chromophores in P1–P3 suppress the intermolecular interactions. The HOMO and LUMO levels of these polymers were estimated from their cyclic voltammograms. The HOMO levels of P0–P3 are very similar (?5.02 to ?5.03 eV), whereas their LUMO levels decrease readily with increasing oxadiazole content (?2.7, ?3.08, ?3.11, and ?3.19 eV, respectively). Therefore, the electron affinity of the poly(p‐phenylenevinylene) chain can be gradually enhanced by incorporating 1,3,4‐oxadiazole segments. Among the polymers, P1 (11 mol % 1,3,4‐oxadiazole) shows the best EL performance (maximal luminance: 3490 cd/m², maximal current efficiency: 0.1 cd/A). Further increase in oxadiazole content results in micro‐phase separation that leads to performance deterioration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4377–4388, 2007     

Synthesis of medium‐bandgap π‐Conjugated polymers based on isomers of 5‐Alkylphenanthridin‐6(5H)‐one and 6‐Alkoxylphenanthridine

Two novel dibromo monomers consisting of the isomers of 5‐alkylphenanthridin‐6(5H)‐one (PN) and 6‐alkoxylphenanthridine (PO) were synthesized through alkylation of the precursor 3,8‐dibromophenanthrindi‐6(5H)‐one, where the molecular structures were confirmed by NMR spectroscopy. The medium bandgap conjugated polymers PDBTPN and PDBTPO were constructed by utilizing such two isomers PN and PO as the electron‐donating units and dithiophenebenzo[2,1,3]diathiazole as the electron‐accepting unit. The resulting polymers exhibited analogous absorption profiles with optical bandgap of 1.90 eV, while PDBTPO showed slightly higher absorption coefficiency. Cyclic voltammetry measurements revealed that these polymers had relatively deep highest occupied molecular orbital levels of about ?5.70 eV. Polymer solar cells based on such two polymers showed relatively high open‐circuit voltage of about 0.90 V. All devices exhibited moderate performances with the best power conversion efficiency of 3.77% achieved based on PDBTPO. Devices based on PDBTPO showed slightly higher power conversion efficiency than those based on PDBTPN, which can be ascribed to higher hole mobility and more favorable film morphology of the former. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2119–2127     

Low bandgap π‐conjugated copolymers based on fused thiophenes and benzothiadiazole: Synthesis and structure‐property relationship study

A series of low bandgap conjugated polymers consisting of benzothiadiazole alternating with dithienothiophene (DTT) or dithienopyrrole (DTP) unit with or without 3‐alkylthiophene bridge have been synthesized. Effect of the fused rings and 3‐alkylthiophene bridge on the thermal, optical, electrochemical, charge transport, and photovoltaic properties of these polymers have been investigated. These polymers show broad absorption extending from 300 to 1000 nm with optical bandgaps as low as 1.2 eV; the details of which can be varied either by incorporating 3‐alkylthiophene bridge or by replacing DTT with DTP. The LUMO levels (?2.9 to ?3.3 eV) are essentially unaffected by the specific choice of donor moiety, whereas the HOMO levels (?4.6 to ?5.6 eV) are more sensitive to the choice of donor. The DTT and DTP polymers with 3‐alkylthiophene bridge were found to exhibit hole mobilities of 8 × 10^?5 and 3 × 10^?2 cm² V^?1 s^?1, respectively, in top‐contact organic field‐effect transistors. Power conversion efficiencies in the range 0.17–0.43% were obtained under simulated AM 1.5, 100 mW cm^?2 irradiation for polymer solar cells using the DTT and DTP‐based polymers with 3‐alkylthiophene bridge as donor and fullerene derivatives as acceptor. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5498–5508, 2009