Direct and indirect electroosmotic flow velocity measurements in microchannels

As microfluidic technologies mature, increasingly complex solutions are employed, and accurate methods for the measurement of electroosmotic flow rates are becoming increasingly important. The methodologies of both a direct method and an indirect method of flow rate measurement are presented here. The direct method involves flow visualization using trace amounts of a caged fluorescent dye. The indirect method is based on the change in current that occurs when one solution in the microchannel is replaced by another. The results of concurrent and independent measurements of electroosmotic velocities of Tris-acetate with EDTA (TAE) and Tris-borate with EDTA (TBE) at 1x concentration in fused silica capillaries are presented. Although these buffers are commonly used in biological chemistry, these mobilities have not previously been reported. Strong agreement among data collected with both methods establishes confidence in the electroosmotic mobility values obtained and indicates that the current-based method, which requires less infrastructure than the direct method, can provide accurate flow rate measurements under these conditions. Constant electroosmotic mobilities of 4.90 x 10(-8) m(2) V(-1) s(-1) for TAE and 3.10 x 10(-8) m(2) V(-1) s(-1) for TBE were determined by tests in a range of electrical field strengths from 5 to 20 kV/m. A linear flow rate increase with applied field strength indicated that constant mobility and negligible Joule heating effects were present. Applicability and limitations of both the measurement methods and these buffers are discussed in the context of microfluidic applications.     

Power-free poly(dimethylsiloxane) microfluidic devices for gold nanoparticle-based DNA analysis

An extremely simple, power-free pumping method for poly(dimethylsiloxane)(PDMS) microfluidic devices is presented. By exploiting the high gas solubility of PDMS, the energy for the pumping is pre-stored in the degassed bulk PDMS, therefore no additional structures other than channels and reservoirs are required. In a Y-shaped microchannel with cross section of 100 microm width x 25 microm height, this method has provided flow rate of 0.5-2 nL s(-1), corresponding to linear velocity of 0.2-0.8 mm s(-1), with good reproducibility. As an application of the power-free pumping, gold nanoparticle-based DNA analysis, which does not rely on the cross-linking mechanism between nanoparticles, has been implemented in a microchannel with three inlets. Target 15mer DNA has been easily and unambiguously discriminated from its single-base substituted mutant. Instead of colorimetric detection in a conventional microtube, an alternative detection technique suitable for microdevices has been discovered-observation of deposition on the PDMS surfaces. The channel layout enabled two simultaneous DNA analyses at the two interfaces between the three laminar streams.     

Fuel cell-powered microfluidic platform for lab-on-a-chip applications

The achievement of a higher degree of integration of components--especially micropumps and power sources--is a challenge currently being pursued to obtain portable and totally autonomous microfluidic devices. This paper presents the integration of a micro direct methanol fuel cell (μDMFC) in a microfluidic platform as a smart solution to provide both electrical and pumping power to a Lab-on-a-Chip system. In this system the electric power produced by the fuel cell is available to enable most of the functionalites required by the microfluidic chip, while the generated CO(2) from the electrochemical reaction produces a pressure capable of pumping a liquid volume through a microchannel. The control of the fuel cell operating conditions allows regulation of the flow rate of a liquid sample through a microfluidic network. The relation between sample flow rate and the current generated by the fuel cell is practically linear, achieving values in the range of 4-18 μL min(-1) while having an available power between 1-4 mW. This permits adjusting the desired flow rate for a given application by controlling the fuel cell output conditions and foresees a fully autonomous analytical Lab-on-a-Chip in which the same device would provide the electrical power to a detection module and at the same time use the CO(2) pumping action to flow the required analytes through a particular microfluidic design.     

Confocal microscopic evaluation of mixing performance for three-dimensional microfluidic mixer

We developed a confocal microscopic method for a quantitative evaluation of the mixing performance of a three-dimensional microfluidic mixer. We fabricated a microfluidic baker's transformation (MBT) mixer as a three-dimensional passive-type mixer for the efficient mixing of solutions. Although the MBT mixer is one type of ideal mixers, it is hard to evaluate its mixing performance, since the MBT mixer is based on several cycles of complicated three-dimensional microchannel structures. We applied the method developed here to evaluate the mixing of water and a fluorescein isothiocyanate (FITC; diffusion coefficient, 4.9 × 10(-10) m(2) s(-1)) solution by the MBT mixer. This method enables us to capture vertical section images for the fluid distributions of FITC and water at different three-dimensional microchannel structures of the MBT device. These images are in good agreement with those of mixing images based on numerical simulations. The mixing ratio could be calculated by the fluorescence intensity at each pixel of the vertical section image; complete mixing is recognized by a mixing ratio of more than 90%. The mixing ratios are measured at different cycles of the MBT mixer by changing the flow rate; the mixing performance is evaluated by comparisons with the mixing ratio of the straight microchannel without the MBT mixer.     

Field-effect flow control in a polydimethylsiloxane-based microfluidic system.

The application of the field-effect for direct control of electroosmosis in a polydimethylsiloxane (PDMS)-based microfluidic system, constructed on a silicon wafer with a 2.0 microm electrically insulating layer of silicon dioxide, is demonstrated. This microfluidic system consists of a 2.0 cm open microchannel fabricated on a PDMS slab, which can reversibly adhere to the silicon wafer to form a hybrid microfluidic device. Aside from mechanically serving as a robust bottom substrate to seal the channel and support the microfluidic system, the silicon wafer is exploited to achieve field-effect flow control by grounding the semiconductive silicon medium. When an electric field is applied through the channel, a radial electric potential gradient is created across the silicon dioxide layer that allows for direct control of the zeta potential and the resulting electroosmotic flow (EOF). By configuring this microfluidic system with two power supplies at both ends of the microchannel, the applied electric potentials can be varied for manipulating the polarity and the magnitude of the radial electric potential gradient across the silicon dioxide layer. At the same time, the longitudinal potential gradient through the microchannel, which is used to induce EOF, is held constant. The results of EOF control in this hybrid microfluidic system are presented for phosphate buffer at pH 3 and pH 5. It is also demonstrated that EOF control can be performed at higher solution pH of 6 and 7.4 by modifying the silicon wafer surface with cetyltrimethylammonium bromide (CTAB) prior to assembly of the hybrid microfluidic system. Results of EOF control from this study are compared with those reported in the literature involving the use of other microfluidic devices under comparable solution conditions.     

Microfluidic flow transducer based on the measurement of electrical admittance

A new flow transducer for measuring the flow rate of a conducting fluid in a microchannel is reported. In this paper, the measure of flow of such fluid under laminar flow conditions based on the change of electrical admittance is established with the aid of a pair of electrodes parallel to the line of flow in a glass-PDMS microfluidic device. This flow sensor is simple in design and can be integrated to most of the microfluidic platforms. The effect of flow rate of the electrolyte, the frequency of the applied ac voltage, the voltage applied across the detector electrodes, and the conductivity of the electrolyte are varied to optimize for high sensitivity. The optimized values are then used to demonstrate the measurements of very low flow rates (<1 nL s(-1)). This flow sensor can be extended towards the measurement of chemical and biochemical buffers and reagents.     

Continuous and precise particle separation by electroosmotic flow control in microfluidic devices

A new scheme has been described for continuous particle separation using EOF in microfluidic devices. We have previously reported a method for particle separation, called "pinched flow fractionation (PFF)", in which size-dependent and continuous particle separation can be achieved by introducing pressure-driven flows with and without particles into a pinched microchannel. In this study, EOF was employed to transport fluid flows inside a microchannel. By controlling the applied voltage to electrodes inserted in each inlet/outlet port, the flow rates from both inlets, and flow rates distributed to each outlet could be accurately tuned, thus enabling more effective separation compared to the pressure-driven scheme. In the experiment, the particle behaviors were compared between EOF and pressure-driven flow schemes. In addition, micrometer- and submicrometer-sized particles were accurately separated and individually collected using a microchannel with multiple outlet branch channels, demonstrating the high efficiency of the presented scheme.     

Development and characterization of an all-solid-state potentiometric biosensor array microfluidic device for multiple ion analysis

A microfluidic device with an all-solid-state potentiometric biosensor array was developed using microfabrication technology. The sensor array included a pH indicator, and potassium and calcium ion-selective microelectrodes. The pH indicator was an iridium oxide thin film modified platinum microelectrode and the iridium oxide was deposited by an electrochemical method. The potassium and calcium ion-selective microelectrodes were platinum coated with silicon rubber based ion-selective membranes with respectively potassium (valinomycin) and calcium (ETH 1001) ionophores. The detection system was integrated with a micro-pneumatic pump which can continuously drive fluids into the microchannel through sensors at flow rates ranging from 52.4 microl min(-1) to 7.67 microl min(-1). The sensor array microfluidic device showed near-Nernstian responses with slopes of 62.62 mV +/- 2.5 mV pH(-1), 53.76 mV +/- 3 mV -log[K+](-1) and 25.77 mV +/- 2 mV -log[Ca2+](-1) at 25 degrees C +/- 5 degrees C, and a linear response within the pH range of 2-10, with potassium and calcium concentrations between 0.1 M and 10(-6) M. In this study the device provided a convenient way to measure the concentration of hydrogen, potassium and calcium ions, which are important physiological parameters.     

Electro-osmotic flows in a microchannel with patterned hydrodynamic slip walls

We present an analysis of the electro-osmotic flow of electrolytic solutions in a microchannel with patterned hydrodynamic slippage on channel walls. A set of governing equations is formulated to account for the effects of small variations in hydrodynamic slippage over the microchannel walls on the electro-osmotic flow. These equations are then solved analytically by using the perturbation method. Two frequently encountered surface patterns, (i) cosine wave variation and (ii) square wave variation in slip length, are considered in our analyses. The results show that patterned slippage over microchannel walls can induce complex flow patterns (such as vortical flows) in otherwise plug-like electro-osmotic flows, which suggests potential applications of such flows in microfluidic mixers.     

Continuous flow in open microfluidics using controlled evaporation

This paper presents a method for programming the flow rate of liquids inside open microfluidic networks (MFNs). A MFN comprises a number of independent flow paths, each of which starts with an open filling port, has a sealed microchannel in which assays can be performed, and an open capillary pump (CP). The MFN is placed over Peltier elements and its flow paths initially fill owing to capillary forces when liquids are added to the filling ports. A cooling Peltier element underneath the filling ports dynamically prevents evaporation in all filling ports using the ambient temperature and relative humidity as inputs. Another Peltier element underneath the CPs heats the pumps thereby inducing evaporation in the CPs and setting the flow rate in the microchannels. This method achieves flow rates in the microchannels ranging from approximately 1.2 nL s(-1) to approximately 30 pL s(-1), and is able to keep 90% of a 0.6 microL solution placed in an open filling port for 60 min. This simple and efficient method should be applicable to numerous assays or chemical reactions that require small and precise flow of liquids and reagents inside microfluidics.     

A high-throughput dielectrophoresis-based cell electrofusion microfluidic device

A high-throughput cell electrofusion microfluidic chip has been designed, fabricated on a silicon-on-insulator wafer and tested for in vitro cell fusion under a low applied voltage. The developed chip consists of six individual straight microchannels with a 40-μm thickness conductive highly doped Si layer as the microchannel wall. In each microchannel, there are 75 pairs of counter protruding microelectrodes, between which the cell electrofusion is performed. The entire highly doped Si layer is covered by a 2-μm thickness aluminum film to maintain a consistent electric field between different protruding microelectrode pairs. A 150-nm thickness SiO? film is subsequently deposited on the top face of each protruding microelectrode for better biocompatibility. Owing to the short distance between two counter protruding microelectrodes, a high electric field can be generated for cell electrofusion with a low voltage imposed across the electrodes. Both mammalian cells and plant protoplasts were used to test the cell electrofusion. About 42-68% cells were aligned to form cell-cell pairs by the dielectrophoretic force. After cell alignment, cell pairs were fused to form hybrid cells under the control of cell electroporation and electrofusion signals. The averaged fusion efficiency in the paired cells is above 40% (the highest was about 60%), which is much higher than the traditional polyethylene glycol method (<5%) and traditional electrofusion methods (～12%). An individual cell electrofusion process could be completed within 10 min, indicating a capability of high throughput.     

Efficient electrospray ionization from polymer microchannels using integrated hydrophobic membranes

A simple process for realizing stable and reliable electrospray ionization (ESI) tips in polymer microfluidic systems is described. The process is based on the addition of a thin hydrophobic membrane at the microchannel exit to constrain lateral dispersion of the Taylor cone formed during ESI. Using this approach, ESI chips are shown to exhibit well-defined Taylor cones at flow rates as low as 80 nL min(-1) through optical imaging. Furthermore, stable electrospray current has been measured for flow rates as low as 10 nL min(-1) over several hours of continuous operation. Characterization of the electrospray process by optical and electrical monitoring of fabricated ESI chips is reported, together with mass spectrometry validation using myoglobin as a model protein. The novel process offers the potential for low-cost, direct interfacing of disposable polymer microfluidic separation platforms to mass spectrometry.     

CO2 laser microfabrication of an integrated polymer microfluidic manifold for the determination of phosphorus

A simple colorimetric technique is implemented in a polymer microfluidic manifold. The simple chemistry aids an uncomplicated microchannel design, which is fabricated by CO(2) laser ablation. Issues such as bonding of multiple layers, alignment of micro-fabricated structures and integration of optical components are addressed. A demonstration of a stopped flow regime in the microfluidic manifold is also presented.     

Counting bacteria on a microfluidic chip

This paper reports a lab-on-a-chip device that counts the number of bacteria flowing through a microchannel. The bacteria number counting is realized by a microfluidic differential Resistive Pulse Sensor (RPS). By using a single microfluidic channel with two detecting arm channels placed at the two ends of the sensing section, the microfluidic differential RPS can achieve a high signal-to-noise ratio. This method is applied to detect and count bacteria in aqueous solution. The detected RPS signals amplitude for Pseudomonas aeruginosa ranges from 0.05 V to 0.17 V and the signal-to-noise ratio is 5-17. The number rate of the bacteria flowing through the sensing gate per minute is a linear function of the sample concentration. Using this experimentally obtained correlation curve, the concentration of bacteria in the sample solution can be evaluated within several minutes by measuring the number rate of the bacteria flowing through the sensing gate of this microfluidic differential RPS chip. The method described in this paper is simple and automatic, and have wide applications in determining the bacteria and cell concentrations for microbiological and other biological applications.     

Generation of concentration gradient by controlled flow distribution and diffusive mixing in a microfluidic chip

We have developed a simple method to generate a concentration gradient in a microfluidic device. This method is based on the combination of controlled fluid distribution at each intersection of a microfluidic network by liquid pressure and subsequent diffusion between laminas in the downstream microchannel. A fluid dynamic model taking into account the diffusion coefficient was established to simulate the on-chip flow distribution and diffusion. Concentration gradients along a distance of a few hundred micrometers were generated in a series of microchannels. The gradients could be varied by carefully regulating the liquid pressure applied to the sample injection vials. The observed concentration gradients of fluorescent dyes generated on the microfluidic channel are consistent with the theoretically predicted results. The microfluidic design described in this study may provide a new tool for applications based on concentration gradients, including many biological and chemical analyses such as cellular reaction monitoring and drug screening.     

Hydrodynamic filtration for on-chip particle concentration and classification utilizing microfluidics

We propose here a new method for continuous concentration and classification of particles in microfluidic devices, named hydrodynamic filtration. When a particle is flowing in a microchannel, the center position of the particle cannot be present in a certain distance from sidewalls, which is equal to the particle radius. The proposed method utilizes this fact, and is performed using a microchannel having multiple side branch channels. By withdrawing a small amount of liquid repeatedly from the main stream through the side channels, particles are concentrated and aligned onto the sidewalls. Then the concentrated and aligned particles can be collected according to size through other side channels (selection channels) in the downstream of the microchannel. Therefore, continuous introduction of a particle suspension into the microchannel enables both particle concentration and classification at the same time. In this method, the flow profile inside a precisely fabricated microchannel determines the size limit of the filtered substances. So the filtration can be performed even when the channel widths are much larger than the particle size, without the problem of channel clogging. In this study, concentrations of polymer microspheres with diameters of 1-3 microm were increased 20-50-fold, and they were collected independently according to size. In addition, selective enrichment of leukocytes from blood was successfully performed.     

Electrothermal stirring for heterogeneous immunoassays

A technique is proposed to enhance microfluidic immuno-sensors, for example, immunoassays, in which a ligand immobilized on a microchannel wall specifically binds analyte flowing through the channel. These sensors can be limited in both response time and sensitivity by the diffusion of analyte to the sensing surface. In certain applications, the sensitivity and response of these heterogeneous immunoassays may be improved by using AC electrokinetically-driven microscale fluid motion to enhance antigen motion towards immobilized ligands. Specifically, the electrothermal effect is used to micro-stir analyte near the binding surface. Numerical simulations of antigen in a microchannel flow subjected to the electrothermal effect show that 6 V(rms) applied to electrodes near a binding region can increase binding in the first few minutes by a factor of seven. The effectiveness of electrothermal stirring is a strong function of the Damk?hler number. The greatest binding enhancement is possible for high Damk?hler numbers, where the reaction is limited by diffusion. Based on these results, the utility of this technique for diffusion-limited microfluidic sensor applications is demonstrated.     

Microfluidic thermodynamics of the shift in thermal stability of DNA duplex in a microchannel laminar flow

This paper reports the shift in thermal stability of DNA duplex and its thermodynamics spectroscopically, caused by stretching and orientation of DNA strands in a microchannel laminar flow. For direct spectroscopic measurement of the microchannel, we prepared an in-house temperature-controllable microchannel-type flow cell. The melting curves of DNA oligomers in a microchannel laminar flow were measured. For DNA oligomers with more than 10 base pairs, the melting curve shifted to the high-temperature side with higher flow speed. However, for 8-base-pair DNA oligomers, a change in the melting profile was not observed in batchwise and microchannel flows. We undertook microfluidic thermodynamic analysis to elucidate details of the shift in thermal stability of the DNA duplex in a microchannel laminar flow. Enthalpy-entropy compensation is applicable to the microfluidic thermal stability shift. We studied the relationships between the enthalpy-entropy compensation and DNA strand length or flow speed. Results showed that the enthalpy-entropy compensation was influenced by both DNA strand length and flow speed, and the penalties of enthalpy were 2-12% greater than the benefits of entropy.     

DC-biased AC-electrokinetics: a conductivity gradient driven fluid flow

This paper studies the principles of fluid flow manipulation based on DC-biased AC-electrokinetics. This method makes use of planar parallel electrodes in a microfluidic channel in contact with an electrolyte solution, with a DC biased AC electrical signal applied to the electrode pair. Due to the application of DC bias, incipient Faradaic electrolytic reactions take place resulting in an increase of the ionic content of the bulk solution. The ionic content was found to be dissimilar at the cathodic and anodic sides of the channel and a conductivity difference of approximately 10% was measured for 2 V(DC). Fluid flow is generated by the action of the DC biased AC electric signal acting on the transverse conductivity gradient generated across the microchannel. The induced flow in the form of vortex was characterized experimentally and the results substantiated theoretically. The velocity of the induced flow vortex under the employed experimental conditions was ~600 to 700 μm s(-1) which is faster than those obtained in conventional AC-electroosmosis and AC-electrothermal types of flows.     

Control of flow rate and concentration in microchannel branches by induced-charge electrokinetic flow

This paper presents a numerical study of controlling the flow rate and the concentration in a microchannel network by utilizing induced-charge electrokinetic flow (ICEKF). ICEKF over an electrically conducting surface in a microchannel will generate vortices, which can be used to adjust the flow rates and the concentrations in different microchannel branches. The flow field and concentration field were studied under different applied electric fields and with different sizes of the conducting surfaces. The results show that, by using appropriate size of the conducting surfaces in appropriate locations, the microfluidic system can generate not only streams of the same flow rate or linearly decreased flow rates in different channels, but also different, uniform concentrations within a short mixing length quickly.