Voltammetric studies of the activity of an electrode made of a graphite-epoxy composite in redox reactions of ascorbic acid and hydroquinone

The potentials of the anodic peak of ascorbic acid oxidation and the potential differences of anodic and cathodic peaks (ΔE _p) of the hydroquinone/benzoquinone redox system at an electrode made of a graphite-epoxy composite are determined in weakly acidic and neutral supporting electrolytes by direct and cyclic voltammetry. The results obtained are compared with thermodynamic values and with the available values of these parameters at different solid electrodes for the above-mentioned redox systems. The effect of aging of the surface of electrodes made of graphite-epoxy composites on the potentials and peak currents of the anodic oxidation of ascorbic acid are studied. It is demonstrated that the regeneration of the electrode surface by mechanically cutting thin layers is important for reducing the δE _p value of the hydroquinone/benzoquinone redox system down to 28–30 mV in supporting electrolytes with pH 2.0 and 7.0. This value is typical of thermodynamically reversible electrode reactions involving two-electron transfer at 20–25°C.     

Electrochemical sensor for detection of p-nitrophenol based on nanoporous gold

Nanoporous gold (NPG) with uniform pore sizes and ligaments was prepared by a simple dealloying method. The as-prepared NPG samples were used as the working electrodes to investigate the redox behavior of p-nitrophenol (p-NP) by cyclic voltammetry (CV). Quite different from the voltammetric behavior of polycrystalline gold electrode, the CV profiles of NPG display a pair of nearly symmetric redox waves which are ascribed to the reaction of 4-(hydroxyamino)phenol/4-nitrosophenol couple. It is interesting that this pair of redox waves are hardly affected by the isomers of p-NP; and moreover, their peak areas are linear with the concentration of p-NP in the range from 0.25 to 10 mg dm^?3. Because of high sensitivity and good selectivity, NPG is expected to act as a promising electrochemical sensor material for detecting trace p-NP in wastewaters.     

Study of photoelectrocatalytic degradation behavior of p-nitrophenol with nano-TiO2 modified film at a rotating ring–disk electrode

The photoelectrocatalytic degradation behavior of p-nitrophenol (pNP) was investigated by using hydrodynamic differential pulse voltammetry (HDPV) technique. The method was applied on a nano-TiO₂ modified platinum rotating ring–disk electrode (RRDE) as versatile working electrode. The voltammetric response of the intermediate product was recorded instantly at the rotating platinum-ring electrode under hydrodynamic conditions via compulsive transport during the photoelectrocatalytic degradation process of pNP. A distinct anodic peak at about 0.55 V is mainly attributed to the result of the formation of electroactive intermediate product, namely hydroquinone (HQ), through the direct reaction between photo-generated powerful oxidant (hydroxyl radicals, OH) and pNP. The present work has demonstrated that HDPV can be effectively used to in situ monitor the formation of intermediate product at nano-TiO₂ modified RRDE, providing a promising approach to investigate the photoelectrocatalytic degradation mechanism of organic pollutants like toxic nitrophenols.     

Direct electrochemistry of myoglobin in a layer-by-layer film on an ionic liquid modified electrode containing CeO2 nanoparticles and hyaluronic acid

We describe an ionic liquid modified electrode (CPE-IL) for sensing hydrogen peroxide (HP) that was modified by the layer-by-layer technique with myoglobin (Mb). In addition, the surface of the electrode was modified with CeO₂ nanoparticles (nano-CeO₂) and hyaluronic acid. UV-vis and FTIR spectroscopy confirmed that Mb retains its native structure in the composite film. Scanning electron microscopy showed that the nano-CeO₂ closely interact with Mb to form an inhomogeneously distributed film. Cyclic voltammetry reveals a pair of quasi-reversible redox peaks of Mb, with the cathodic peak at ?0.357?V and the anodic peak at ?0.269?V. The peak separation (??E _p) and the formal potential (E ^0??) are 88?mV and ?0.313?V (vs. Ag/AgCl), respectively. The Mb immobilized in the modified electrode displays an excellent electrocatalytic activity towards HP in the 0.6 to 78.0???M concentration range. The limit of detection is 50?nM (S/N?=?3), and then the Michaelis-Menten constant is 71.8???M. We believe that such a composite film has potential to further investigate other redox proteins and in the fabrication of third-generation biosensors.

Cathodic voltammetric determination of gold

Cathodic voltammetry at a carbon paste electrode has been evaluated as a technique for the analysis of gold. In the absence of interfering elements the technique is suitable for determinations at concentrations down to 10^?6M. Differentiation of the reduction peak current increases the sensitivity, permitting the determination of gold at concentrations of 10^?7M.     

The electrochemical reduction and determination of reduced nicotinamide adenine dinucleotide in acidic media

The apparent reduction of reduced nicotinamide adenine dinucleotide (NADH) in acidic media at a static mercury drop electrode was investigated. A simple, quick pretreatment procedure was developed to convert the NADH to its acid-hydrated form. This adsorbs on the mercury surface during a film deposition time and the film is then reduced. The adsorption is diffusion-controlled and hence the peak currents for square-wave and linear-scan voltammetry are proportional to Ct^1/2_pAf and Ct^1/2_pAv, respectively, where t_p is the effective film deposition time, C the concentration of NADH, A the electrode area, f the square-wave frequency, and ν the linear scan rate. Several electrochemical techniques were compared for the determination of NADH; the method of choice is square-wave voltammetry, although staircase or linear scan voltammetry can also be used. The detection limit is less than 7 nM, and the range of linear response covers 2–3 orders of magnitude of NADH concentration.     

Preparation of electrochemically reduced graphene oxide-modified electrode and its application for determination of p-aminophenol

A simple and eco-friendly electrochemical method to reduce graphene oxide precursor was employed for fabrication of graphene sheets modified glassy carbon electrode, and then, the resulting electrode [electrochemically reduced graphene oxide (ERGO)/glassy carbon electrode (GCE)] was used to determine p-aminophenol. The experimental results demonstrated that the modified electrode exhibited excellent electrocatalytic activity toward the redox of p-aminophenol as evidenced by the significant enhancement of redox peak currents and the decreased peak-to-peak separation in comparison with a bare GCE. A highly sensitive and selective voltammetry determination of p-aminophenol is developed using the ERGO/GCE. This method has been applied for the direct determination of p-aminophenol in artificial wastewater.     

The effects of abrasive particles on the electrochemical behavior of adrenaline at different electrodes

Cyclic voltammetry (CV), double-potential step chronocoulometry (DPSCC), and electrochemical impedance spectroscopy (EIS) techniques have been performed to study the effects of abrasive particles on the electrochemical reaction of adrenaline at glassy carbon electrode (GCE) and platinum electrode in 0.5 mol/L H₂SO₄ solution. For the electrochemical reaction of adrenaline, it was shown that abrasive particles have a more marked electrocatalytic effect at GCE compared to that at platinum electrode. The electrocatalytic effect of SiC coated GCE is more obvious comparing to that of Al₂O₃ coated GCE. With the coarse degree of the abrasive paper increasing, the peak current (i _p) increases significantly and the peak-to-peak potential separation (ΔE _p) changes a little at the pretreated GCE. The electron transfer process of adrenaline at the different pretreated GCE is controlled by the diffusion in this system.     

Voltammetric Behavior and Determination of Tocopherol in Vegetable Oils at a Polypyrrole Modified Electrode

The voltammetric behavior of α‐tocopherol in the presence of vegetable oil is studied at a polypyrrole modified Pt electrode in a 1,2‐dichloroethane‐ethanol medium with cyclic voltammetry. Cyclic voltammogram of α‐tocopherol showed a well‐defined oxidation peak; the peak potential shifting toward less positive and a much higher peak current obtained at a polypyrrole modified electrode than that obtained at the unmodified Pt electrode. An electroanalytical method for the determination of α‐tocopherol based on its electrochemical oxidation at the polypyrrole modified Pt electrode is developed. Using differential pulse voltammetry, the peak currents were found to increase linearly with the α‐tocopherol concentration over the range of 5.0 to 300 μM, with a sensitivity of 5.38×10^?2 A L mol^?1 and the limit of detection of 1.5 μM (S/N=3), the detection time being about 90 s for each assay. The interference of other synthetic antioxidants such as TBHQ, BHA and BHT to the analysis of α‐tocopherol was investigated. The developed method is applied to the quantification of tocopherols in six vegetable oils, showing that the results are in good agreement with those by HPLC method.     

The use of a new pulsed solid electrode in the study of redox processes by alternating current voltammetry

The behaviour of a pulsed platinum electrode in an a.c. voltammetric study of ferrocene in aprotic medium and p-aminophenol in acetate buffer is reported. The experimental results obtained suggest that the new solid electrode may be also employed to characterize the nature of electrode processes using a.c. To this purpose the oxidation of 2-phenyl-3-(p-methoxyphenyl)-amine indole in aprotic media is re-examined by phase sensitive a.c. voltammetry.     

Electrochemical Characteristics of Poly(<Emphasis Type="Italic">o</Emphasis>-Aminobenzoic Acid) Modified Glassy-Carbon Electrode and Its Electrocatalytic Activity towards Oxidation of Epinephrine

Poly(o-aminobenzoic acid) (o-ABA) film is deposited on glassy-carbon electrode (GCE) by electropolymerization in pH 7.0 phosphate buffer solution (PBS). Electrochemical behavior of modified electrode is investigated by electrochemical impedance spectroscopy (EIS), different pulse voltammetry (DPV), and cyclic voltammetry (CV). The results indicate that there is a greater resistance during the electron transfer process in poly(o-ABA) film than in bare GCE for the redox of [Fe(CN)₆]³⁻/[Fe(CN)₆]⁴⁻. Further research indicates that epinephrine (EP) can be strongly absorbed on the surface of the poly(o-ABA) film-modified electrode. The modified electrode shows an excellent electrocatalytical activity on EP oxidation. The EP cathodic peak potential shifts negatively with a slope of −53.5 mV/pH, indicating that equal amounts of proton and electron are involved in the electrode reaction process. In pH 7.0 PBS, the peak current of EP and the concentration has a linear relationship from 0 to 65 μM by amperometric current-time curve. __________ From Elektrokhimiya, Vol. 41, No. 9, 2005, pp. 1059–1065. Original English Text Copyright ? 2005 by Cheng, Jin, Zhang. The text was submitted by the authors in English.     

Electroanalysis of Carbendazim using MWCNT/Ca‐ZnO Modified Electrode

The present research involves the report on electrochemical deportment of Carbendazim (MBC) at multiwalled carbon nanotubes and calcium‐doped zinc oxide nanoparticles altered nanocomposite based carbon paste electrode (MWCNTs/Ca‐ZnO‐CPE). The modified carbon paste evidenced manifest electrocatalytic behavior for MBC in 0.2 M phosphate buffer (PB) solutions. Cyclic voltammetry (CV), linear sweep voltammetry (LSV), and square wave voltammetry (SWV) techniques were used for the analysis. The working electrode assembly exhibits faster electron transfer of MBC with increase in the peak current. At bare CPE, MBC showed maximum peak current of 1.098 μA at potential 0.7568 V whereas at MWCNT/Ca‐ZnO/CPE peak current of 5.203 μA was observed at potential 0.7541 V in 0.2 M PBS of pH 7.0 at the sweep rate of 50 mV s^?1. The synthesized 5 % Ca‐ZnO nanoparticles (NPs) were characterized by X‐ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive X‐ray analysis (EDX), and Transmission electron microscopy (TEM) analysis. Various factors influencing the voltammetry of MBC such as pre‐concentration time, pH, sweep rate, and amount of MBC were studied and from the studies we observed that the response was found to be diffusion‐controlled. The concentration variation studies for MBC was watched in the linear working range of 0.01 μM to 0.45 μM and the detection limit was found by SWV technique.     

Electrocatalytic Oxidation and Voltammetric Determination of Hydrazine on the Tetrabromo‐p‐Benzoquinone Modified Carbon Paste Electrode

The electrochemical properties of hydrazine studied at the surface of a carbon paste electrode spiked with p‐bromanil (tetrabromo‐p‐benzoquinone) using cyclic voltammetry (CV), double potential‐step chronoamperometry and differential pulse voltammetry (DPV) in aqueous media. The results show this quinone derivative modified carbon paste electrode, can catalyze the hydrazine oxidation in an aqueous buffered solution. It has been found that under the optimum conditions (pH 10.00), the oxidation of hydrazine at the surface of this carbon paste modified electrode occurs at a potential of about 550 mV less positive than that of a bar carbon paste electrode. The electrocatalytic oxidation peak current of hydrazine showed a linear dependent on the hydrazine concentrations and linear analytical curves were obtained in the ranges of 6.00×10^?5 M–8.00×10^?3 M and 7.00×10^?6 M–8.00×10^?4 M of hydrazine concentration with CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 3.6×10^?5 M and 5.2×10^?6 M by CV and DPV methods. This method was also used for the determination of hydrazine in the real sample (waste water of the Mazandaran wood and paper factory) by standard addition method.     

Voltammetric study on interaction of cysteine with type I-collagen in the aqueous medium

Interaction of cysteine with type I-collagen from bovine achilles tendon in the aqueous solutions has been examined using square wave voltammetry (SWV) and cyclic voltammetry (CV) techniques. In the absence of cysteine, type I-collagen gives a reversible peak at ?0.114 V in Britton-Robinson (B-R) buffer (pH 4.0). The electrochemical parameters (I _p/f, E _p/f, E _p/pH, I _p/pH, I _p/v, I _p/v^1/2) of type I-collagen have been also studied. In addition, it has been determined that there is a linear relationship between current and concentration of type I-collagen. On the other hand, cysteine exhibits a reversible peak at ?0.383 V due to the reduction of mercurous cysteine thiolate. By using a hanging mercury drop electrode in aqueous solutions, SWV and CV voltammograms obtained for type I-collagen in the presence of cysteine indicate that there is an interaction between type I-collagen and cysteine. In the presence of cysteine, peak current of type I-collagen decreases and a new peak is observed at ?0.121 V for cysteine which is bonded to type I-collagen.     

Cyclic Square Wave Voltammetry: Theory and Experimental

Abstract

The voltage wave form of cyclic square wave voltammetry (CSWV) and its theory are presented, and experimental verification of theoretical work for CSWV is given. Indications are that the peak potential difference, E_p, of the differential current between the forward sweep and the reverse sweep is zero. Their peak heights have the same value for a reversible electrode reaction, zero, a different value for a reversible electrode reaction with stripping process, not zero, and the same value for a quasi-reversible electrode reaction. According to this property, the reversibility of an electrode reaction can be easily determined.     

The use of a rotating lead-disk electrode for electroanalytical purposes

The behavior of lead as an electrode material for electroanalytical purposes was studied in 1.0 M sulfuric acid. The useful negative range of potential was approximately ?0.57 to ?1.20 V vs. SCE for conventional voltammetry at a rotating disk electrode. For the sinusoidal hydrodynamic modulation technique, the negative limit was about ?1.25 V. Studies of the reduction of cadmium ion, thallium(I) ion, and p-nitroaniline showed that the behavior of a rotating lead-disk electrode was comparable to that expected on the basis of theory. Limits of detection are in the micromolar range.     

Electrochemical investigation of a glassy carbon electrode modified with carbon nanotubes decorated with (poly)crystalline gold

Multiwalled carbon nanotubes with nanosized sputtered gold were used to modify a glassy carbon electrode (GCE). The substrate was characterized by scanning electron microscopy (SEM), X-ray diffraction, cyclic voltammetry and amperometry. SEM micrographs indicated an uniform coverage of the carbon nanotubes with nanosized (poly)crystalline gold. Cyclic voltammetry reveals that peak separation of the unmodified GCE in the presence of 1?mM ferricyanide is 131?mV, but 60?mV only for the modified GCE. In addition, the oxidation of NADH (1?mmol?L^?1 solution) begins at negative potentials (around ?100?mV vs. Ag/AgCl), and the anodic peak potential (corresponding to the irreversible oxidation of NADH) is found at +94?mV. The effect of pH on the electrocatalytic activity was studied in the range from 5.4 to 8.0. The relationship between the anodic peak potential and the pH indicated a variation of ?33.5?mV/pH which is in agreement with a two-electron and one-proton reaction mechanism. Amperometry, performed at either ?50 or +50?mV vs. an Ag/AgCl reference electrode, indicates that the modified electrode is a viable amperometric sensor for NADH. At a working potential of +50?mV, the response to NADH is linear in the concentration range from 1 to 100???mol?L^?1, with an RSD of 6% (n?=?4).

Poly(2,2′-(1,4-phenylenedivinylene) Bis-8-hydroxyquinaldine) Modified Glassy Carbon Electrode for the Simultaneous Determination of Paracetamol and p-Aminophenol

A novel assay is reported for the simultaneous determination of paracetamol and p-aminophenol using a poly(2,2′-(1,4-phenylenedivinylene)bis-8-hydroxyquinaldine) modified glassy carbon electrode. Poly(2,2′-(1,4-phenylenedivinylene)bis-8-hydroxyquinoline) modified electrodes were prepared by electrochemical polymerization. The electrode surface was characterized by scanning electron microscopy. The electrochemical behavior of the modified electrode was investigated by cyclic voltammetry, square wave voltammetry, and electrochemical impedance spectroscopy. The anodic peak potentials for paracetamol and p-aminophenol were at 580 and 337 millivolts, respectively, with a separation of 243 millivolts, adequate for their simultaneous determination. The results showed that the linear dynamic ranges for paracetamol and p-aminophenol were 0.5–200 micromolar and 3–150 micromolars, whereas the limits of detection were 0.075 and 0.45 micromolar, respectively. The novel poly(2,2′-(1,4-phenylenedivinylene)bis-8-hydroxyquinaldine) modified electrode provided excellent selectivity, sensitivity, and stability and was employed for the determination of paracetamol and p-aminophenol in pharmaceutical products and urine.     

The renovated silver ring electrode

In this preliminary note, a new type of working electrode – the renovated silver ring electrode (RSRE) – is presented. The main constituents of the RSRE: a specially constructed silver ring electrode, a silver sheet used as silver counter/quasi-reference electrode and a silicon O-ring are fastened together in a polypropylene body. The renovation of this electrode is carried out through mechanical removal of solid contaminants and electrochemical activation in the electrolyte which fills the RSRE body. The effectiveness of the renovation procedure was tested by designating the RF and E_pzc and by recording C_d–t curves. As shown on selected examples, RSRE exhibits good performance in underpotential deposition stripping voltammetry (UPD-SV) applied for the determination of Pb(II) traces in certified reference materials.     

Detection of Uric Acid in the Presence of Dopamine and High Concentration of Ascorbic Acid Using PDDA Modified Graphite Electrode

The properties of graphite electrode (Gr) modified with poly(diallyl dimethyl ammonium chloride) (PDDA) for the detection of uric acid (UA) in the presence of dopamine (DA) and high concentration of ascorbic acid (AA) have been investigated by cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The polymer modified graphite electrode was prepared by a very simple method just by immersing the graphite electrode in PDDA solution for 20 minutes. The PDDA/Gr modified electrode displayed excellent electrocatalytic activity towards the oxidation of UA, DA and AA compared to that at the bare graphite electrode. The electrochemical oxidation signals of UA, DA and AA are well resolved into three distinct peaks with peak potential separations of 220 mV, 168 mV and 387 mV between AA‐DA, DA‐UA and AA‐UA respectively in cyclic voltammetry studies and the corresponding peak potential separations are 230 mV, 130 mV and 354 mV respectively in differential pulse voltammetry. The lowest detection limits obtained for UA, DA and AA were 1×10^?7 M, 2×10^?7 M and 800×10^?9 M respectively. The PDDA/Gr electrode efficiently eliminated the interference of DA and a high concentration of AA in the determination of UA with good selectivity, sensitivity and reproducibility. The modified electrode was also successfully applied for simultaneous determination of UA, DA and AA in their ternary mixture.