Luminescent copoly(aryl ether)s with new electron‐transporting bis(3‐(trifluoromethyl)phenyl)‐1,3,4‐oxadiazole or bis(3‐(trifluoromethyl)phenyl)‐4‐(4‐hexyloxyphenyl)‐4H‐1,2,4‐triazole segments

To investigate the effect of trifluoromethyl groups in enhancing electron affinity of aromatic oxadiazole and triazole chromophores, we prepared four new copoly(aryl ether)s ( P1 – P4 ) consisting of bis(3‐(trifluoromethyl) phenyl)‐1,3,4‐oxadiazole (ETO) or bis(3‐(trifluoromethyl)phenyl)‐4‐(4‐hexyloxyphenyl)‐4H‐1,2,4‐triazole (ETT) segments and hole‐transporting segments [2,5‐distyrylbenzene (HTB) or bis(styryl)fluorine (HTF)]. Molecular spectra (absorption and photoluminescence) and cyclic voltammetry were used to investigate their optical and electrochemical properties. The emissions of P1 – P4 are dominated by the hole‐transporting fluorophores with longer emissive wavelengths around 442–453 nm via efficient excitation energy transfer. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of P1 – P4 , estimated from electrochemical data, are ?5.15, ?5.18, ?5.30, ?5.27, ?3.39, ?3.49, ?3.36, and ?3.48 eV, respectively. The LUMO levels of ETO and ETT segments are significantly reduced to ?3.39～?3.36 eV and ?3.48～?3.49 eV, respectively, as compared with ?2.45 eV of P5 containing a 2,5‐diphenyl‐1,3,4‐oxadiazole segment. Moreover, electron and hole affinity can be enhanced simultaneously by introducing isolated hole‐ and electron‐transporting segments in the backbone. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5900–5910, 2004     

Photoluminescent and electrochemical properties of novel copoly(aryl ether)s with isolated fluorophores

Two, novel copoly(aryl ether)s ( P1 and P2 ) consisting of alternate, isolated electron‐ and hole‐transporting fluorophores were synthesized and characterized. Furthermore, we investigated the optical, photoluminescent (PL), and electrochemical properties of copoly(aryl ether)s P1 – P5 . The PL spectra of these polymers in film states showed maximum peaks around 420–498 nm. However, compared with the PL spectra of corresponding model compounds M1 – M5 , the emissions of P1 and P2 were compositions of the two isolated fluorophores, and that of P3 was dominated by the fluorophores with a longer emissive wavelength via the energy transfer. The formation of an interchain interaction in P4 and P5 was also observed. The highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels of these copolymers were measured by cyclic voltammetry. Both the electron and hole affinities could be enhanced simultaneously because of the introduction of isolated hole‐transporting naphthalene (or fluorene) and electron‐transporting bis‐1,3,4‐oxadiazole segments. The single‐layer devices (Al/polymer/indium tin oxide) of P1 , P2 , and P4 revealed blue or blue‐green electroluminescence, but that of P3 emitted yellow light because of the excimer emission. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 883–893, 2004     

Luminescent copoly(aryl ether)s consisting of alternate oxadiazole and 1,4‐distyrylbenzene derivatives: Synthesis and characterization

In an effort to decrease the electron‐injection barrier from the anode electrode, four copoly(aryl ether)s ( P1 – P4 ), consisting of alternating isolated electron‐transporting [2,5‐diphenyl‐1,3,4‐oxadiazole for P1 and P3 and 5,5′‐diphenyl‐2,2′‐p‐(2,5‐bishexyloxyphenylene)‐bis‐1,3,4‐oxadiazole for P2 and P4 ] and emitting chromophores (1,4‐distyryl‐2,5‐dihexyloxybenzene for P1 and P2 and 1,4‐distyryl‐2,5‐dihexylbenzene for P3 and P4 ), have been synthesized by the nucleophilic displacement reaction between bisfluoride and bisphenol monomers. They are basically amorphous materials with 5% weight‐loss temperature above 400 °C. The photoluminescence spectra and quantum yields of these copolymers are dependent on the compositions of the two isolated fluorophores. The highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels of these copolymers have been estimated from their cyclic voltammograms. All the observations directly prove that the oxidation starts at the hole‐transporting segments. The electron affinity can be enhanced by the introduction of isolated electron‐transporting segments that lead to a charge‐injection balance. Single‐layer light‐emitting diodes (Al/ P1 – P4 /ITO glass) have been fabricated. P1 and P2 reveal blue electroluminescence, and P3 and P4 reveal purple‐blue electroluminescence. Moreover, the incorporation of bisoxadiazole units increases the electron affinity and reduces the turn‐on electric field better than one oxadiazole unit. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2765–2777, 2003     

Poly(p‐phenylene vinylene) derivatives containing triazole or oxadiazole segments: Connector effect in optical,electrochemical, and electroluminescent properties

To study the effect of connector structure between hole‐ and electron‐transporting segments, we synthesized and characterized new electroluminescent polymers P 1 – P 7 consisting of hole‐transporting 1,4‐bis(hexyloxy)‐2,5‐distyrylbenzene (DSB: P 1 and P 2 ) and electron‐transporting 4‐(4‐(hexyloxy)phenyl)‐3,5‐diphenyl‐4H‐1,2,4‐triazole (TAZ: P 3 and P 4 ) or 2‐(2,5‐bis(hexyloxy)‐4‐(5‐phenyl‐1,3,4‐oxadiazol)phenyl)‐5‐phenyl‐1,3,4‐oxadiazole (DIOXD: P 5 – P 7 ) segments linked by different connectors. The connectors between hole‐ and electron‐transporting segments are (1) 1,4‐phenylene in P 3 and P 5 , (2) 1,4‐divinylbenzene in P 4 and P 6 , and (3) 4,4′‐biphenyl in P 7 . Three corresponding end‐capped model polymers P 1‐M , P 2‐M , and P 3‐M were also synthesized to evaluate the effect of end groups. From optimized semiempirical MNDO calculations, the adjacent benzene rings between DSB and TAZ or DIOXD chromophores in P 3 , P 5 , and P 7 twist about 81°–89°. The effect of twisted architectures and connectors in optical and electrochemical properties for P 1 – P 7 have been discussed by comparing with copolymers P 1 and P 2 , which possess single bond or ether spacer as connectors. From cyclic voltammograms, the torsion in P 3 , P 5 , and P 7 confines electron delocalization and leads to simultaneously enhanced hole and electron affinity as compared to those of P 1 and P 2 . Furthermore, double‐layer light‐emitting diodes with a configuration of ITO/PEDOT:PSS/ P 1 – P 7 /Al all reveal green–yellow electroluminescence with maximum luminance at 8–320 cd/m² and their performances are greatly influenced by the connector's structure. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4514–4531, 2006     

Synthesis of electroluminescent copoly(aryl ether)s containing alternate 1,4‐distyrylbenzene derivatives and aromatic 1,3,4‐oxadiazole or 3,3″‐terphenyldicarbonitrile segments

New copoly(aryl ether)s ( P1 – P3 ) containing alternate 2,5‐dihexyloxy‐1,4‐di(m‐ethoxystyryl)benzene ( P1 , P2 ) or 2,5‐dihexyloxy‐1,4‐distyrylbenzene ( P3 ) chromophores and aromatic 1,3,4‐oxadiazole ( P1 ) or 3,3″‐terphenyldicarbonitrile ( P2 , P3 ) segments were prepared by Horner reaction ( P1 and P2 ) or nucleophilic displacement reaction ( P3 ). They are basically amorphous materials with 5% weight‐loss temperature above 410 °C. Their absorption, photoluminescence spectra, and quantum yields are dependent on the composition of the isolated fluorophores. The emissions are exclusively dominated by 1,4‐distyrylbenzene segments via excitation energy transfer from electron‐transporting 1,3,4‐oxadiazole ( P1 ) or 3,3″‐terphenyldicarbonitrile ( P2 , P3 ) chromophores. The HOMO and LUMO energy levels have been estimated from their cyclic voltammograms, and the observations confirm that oxidation and reduction start from the emitting 1,4‐distyrylbenzene and electron‐transporting segments, respectively, indicating that both carriers affinity can be enhanced simultaneously. Among the two‐layer PLED devices (ITO/PEDOT/ P1 – P3 /Al), P1 exhibits the best performance with a turn‐on field of 4 × 10⁵ V/cm and a maximum luminance of 225 cd/m². However, P2 emits green–yellow light (555 nm), owing to the excimer emission. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5009–5022, 2005     

Bipolar copoly(aryl ether) containing distyrylbenzene,triphenylamine, and 1,2,4‐triazole moieties: Synthesis and optoelectronic properties

A novel copoly(aryl ether) ( P1 ) consisting of alternate emitting segments (distyrylbenzene) and a bipolar moiety composed of directly linked electron‐transporting aromatic 1,2,4‐triazole and hole‐transporting triphenylamine was synthesized. The copoly(aryl ether) is readily soluble in common organic solvents and exhibit good thermal stability with thermal decomposition temperature above 450 °C. The emission and the photoluminescence quantum yield of the copolymer are dominated by the emitting segments (distyrylbenzene) with longer emissive wavelength. Electron affinity of P1 is evidently enhanced after introducing the isolated bipolar unit, as confirmed by the lowered lowest unoccupied molecular orbital level (–2.77 eV) relative to P0 without bipolar unit (–2.34 eV). This results in improved emission efficiency of its polymer light‐emitting diode (indium tin oxide/poly(3,4‐ethylene dioxythiophene):poly(styrene sulfonate)/ P1 /LiF/Ca/Al) due to more balanced charges injection and transport. Blending P1 with poly(9,9‐dihexylfluorene) ( PF ) further improves the efficiency of the device; the best performance was obtained for PF / P1 = 20/0.8 (w/w) with maximum luminance and maximum luminance efficiency being significantly enhanced to 3260 cd/m² and 1.08 cd/A, respectively, from 380 cd/m² and 0.009 cd/A of P1 ‐based device. These results demonstrate that the bipolar moiety can be used to enhance charges injection and transport of electroluminescent polymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Luminescent copolyethers containing isolated 1,4‐distyrylbenzene derivatives backbone and 7‐oxy‐4‐methylcoumarin side group: Synthesis and characterization

Four new copolyethers ( P1 – P4 ) consisting of two isolated emitting chromophores [2,5‐dihexyloxy‐1,4‐distyrylbenzene (HODSB) and 2,5‐dihexyloxy‐1,4‐di(4‐methylenestyryl)benzene (HOMDSB) for P1 and P2 , 2,5‐dihexyl‐1,4‐distyrylbenzene (HDSB) and HOMDSB for P3 and P4 ] in the backbone, in which P2 and P4 further contain electron‐transporting chromophores [7‐oxy‐4‐methylcoumarin (OMC)] in the side chain, were successfully prepared by the Heck coupling reaction. The photoluminescence spectra and quantum yields of the copolymers depended mainly on compositions of the isolated fluorophores. Their highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels were estimated from their cyclic voltammograms. Electrochemical investigations proved that the oxidation started at hole‐transporting DSB segments, whereas reduction began at electron‐transporting OMC groups in P2 and P4 . The electron affinity of P2 and P4 was enhanced by introducing electron‐transporting OMC chromophores. Double‐layer light‐emitting diodes (ITO/PEDOT:PSS / polymer/Al) of P1 and P2 revealed green electroluminescence, and those of P3 and P4 emitted blue light. Moreover, incorporation of OMC side groups effectively reduced turn‐on electric field and enhanced luminance efficiency of the EL devices due to increased electron affinity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 211–221, 2007     

Optical and electroluminescent properties of novel poly(aryl ether)s with isolated carbazole and p‐quaterphenyl fluorophores

We report the optical and electroluminescent properties of four novel poly(aryl ether)s ( P1 – P4 ) consisting of alternate isolated hole‐transporting [carbazole or 3,6‐bis(styryl)carbazole] and electron‐transporting [dicyano‐p‐quaterphenyl or bis(trifluoromethyl)‐p‐quaterphenyl] fluorophores. The photoluminescence (PL) spectra of the four polymeric films show maximum peaks around 407–413 nm for P1 , P2 and 442–447 nm for P3 , P4 . The PL spectra of P1 ～ P4 are dependent on the composition of the two isolated fluorophores. According to the observation of relative quantum yield in poor solvent (cyclohexane), P2 containing more bulky trifluoromethyl groups in p‐quaterphenyl segments prevented aggregate quenching processes more than P1 . Compared with P1 and P2 with carbazole segments, P3 and P4 with 3,6‐bis(styryl)carbazole segments exhibited less interchain interaction and a low threshold electric field in a single‐layer device. The p‐quaterphenyl and carbazole [or 3,6‐bis(styryl)carbazole] segments were regarded as electron‐transporting and hole‐transporting units, respectively, in the single‐layer light‐emitting diodes (Al/ P1 – P4 /ITO). In the double‐layer device (ITO/MEH‐PPV/ P2 /Al), the maximum luminance was doubled, and the threshold electric fields diminished because P2 functioned as an electron‐transporting and hole‐blocking layer. Furthermore, the voltage‐tunable multicolor emission from orange to green was observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 333–340, 2004     

Synthesis and characterization of new poly(aryl ether)s with isolated fluorophores

Four novel poly(aryl ether)s ( P1 – P4 ) consisting of alternate isolated electron‐transporting (3,3″′‐bis‐trifluoromethyl‐p‐quaterphenyl for P1 , P3 or 3,3″′‐dicyano‐p‐quaterphenyl for P2 , P4 ) and hole‐transporting fluorophores [N‐(2‐ethylhexyl)‐3,6‐bis(styryl)carbazole for P1 , P2 or 9,9‐dihexyl‐2,7‐bis(styryl)fluorene for P3 , P4 ] were synthesized and characterized. These poly(aryl ether)s can be dissolved in organic solvents and exhibited good thermal stability with 5% weight‐loss temperature above 500 °C in nitrogen atmosphere. The photoluminescent (PL) spectra of the films of these polymers showed maximum peaks at around 442–452 nm. The PL spectral results revealed that the emission of polymers was dominated by the fluorophores with longer emissive wavelength via the energy transfer from p‐quaterphenyl to 3,6‐bis(styryl)carbazole or 2,7‐bis(styryl)fluorene segments. Therefore, the p‐quaterphenyl segments function only as the electron‐transporting/hole‐blocking units in these polymers, and the other segments are the emissive centers and hole‐transporting units. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital energy levels of these polymers were measured by cyclic voltammetry. The electron‐donating nitrogen atom on carbazole resulted in the higher HOMO energy levels of P1 and P2 than those of P3 and P4 . The single‐layer light‐emitting diodes (LED) of Al/poly(aryl ether)s ( P1 – P4 )/ITO glass were fabricated. P1 , P2 , and P4 revealed blue electroluminescence, but P3 emitted yellow light as a result of the excimer emission. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2215–2224, 2002     

Synthesis and optoelectronic properties of luminescent poly(p‐phenylenevinylene) derivatives containing electron‐transporting 1,3,4‐oxadiazole groups

Three random copolymers ( P1–P3 ) comprising phenylenevinylene and electron‐transporting aromatic 1,3,4‐oxadiazole segments (11, 18, 28 mol %, respectively) were prepared by Gilch polymerization to investigate the influence of oxadiazole content on their photophysical, electrochemical, and electroluminescent properties. For comparative study, homopolymer poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐p‐phenylenevinylene] ( P0 ) was also prepared by the same process. The polymers ( P0–P3 ) are soluble in common organic solvents and thermally stable up to 410 °C under a nitrogen atmosphere. Their optical properties were investigated by absorption and photoluminescence spectroscopy. The optical results reveal that the aromatic 1,3,4‐oxadiazole chromophores in P1–P3 suppress the intermolecular interactions. The HOMO and LUMO levels of these polymers were estimated from their cyclic voltammograms. The HOMO levels of P0–P3 are very similar (?5.02 to ?5.03 eV), whereas their LUMO levels decrease readily with increasing oxadiazole content (?2.7, ?3.08, ?3.11, and ?3.19 eV, respectively). Therefore, the electron affinity of the poly(p‐phenylenevinylene) chain can be gradually enhanced by incorporating 1,3,4‐oxadiazole segments. Among the polymers, P1 (11 mol % 1,3,4‐oxadiazole) shows the best EL performance (maximal luminance: 3490 cd/m², maximal current efficiency: 0.1 cd/A). Further increase in oxadiazole content results in micro‐phase separation that leads to performance deterioration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4377–4388, 2007     

Copoly(p‐phenylene)s containing bipolar triphenylamine and 1,2,4‐triazole groups: Synthesis,optoelectronic properties,and applications

Two novel copoly(p‐phenylene)s ( P1 – P2 ) containing bipolar groups (12.8 and 6.8 mol %, respectively), directly linked hole transporting triphenylamine and electron transporting aromatic 1,2,4‐triazole, were synthesized to enhance electroluminescence (EL) of poly(p‐phenylene vinylene) (PPV) derivatives. The bipolar groups not only enhance thermal stability but also promote electron affinity and hole affinity of the resulting copoly(p‐phenylene)s. Blending the bipolar copoly‐(p‐phenylene)s ( P1 – P2 ) with PPV derivatives ( d6‐PPV ) as an emitting layer effectively improve the emission efficiency of its electroluminescent devices [indium tin oxide (ITO)/poly(3,4‐ethylenedioxythiophene) (PEDOT):poly(styrenesulfonate) (PSS)/polymer blend/Ca (50 nm)/Al (100 nm)]. The maximum luminance and maximum luminance efficiency were significantly enhanced from 310 cd m^?2 and 0.03 cd A^?1 ( d6‐PPV ‐based device) to 1450 cd m^?2 and 0.20 cd A^?1 (blend device with d6‐PPV / P1 = 96/4 containing ～0.5 wt % of bipolar groups), respectively. Our results demonstrate the efficacy of the copoly(p‐phenylene)s with bipolar groups in enhancing EL of PPV derivatives. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characterization of luminescent polyethers with 2,5‐distyrylthiophene and aromatic oxadiazole chromophores

Two new luminescent copolyethers ( P1 and P2 ) with isolated 2,5‐distyrylthiophene‐emitting segments and electron‐transporting 2,5‐diphenyl‐1,3,4‐oxadiazole chromophores were successfully synthesized by the Horner–Wadworth–Emmons reaction. The solubility, optical, and electrochemical properties of the polymers were investigated and correlated with nonlinear thiophene and 1,3,4‐oxadiazole groups. P2 with pendant 1,3,4‐oxadiazole was soluble in common organic solvents such as chloroform, tetrahydrofuran, and C₂H₂Cl₄. Thermogravimetric analysis and differential scanning calorimetry showed that the copolyethers were thermally stable below 345 °C, with glass‐transition temperatures higher than 110 °C. They were yellow‐greenish emitting materials with a band gap of 2.57–2.58 eV estimated from the onset absorption. Incorporating the thiophene moiety narrowed the band gaps of the copolyethers. The photophysical and electronic properties of the polymer and the preliminary electroluminescent device made from the polymer demonstrate that the polymer may be a potential candidate material for the fabrication of polymeric light‐emitting devices. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2927–2936, 2002     

Theoretical studies of the modulation of polymer electronic and optical properties through the introduction of the electron-donating 3,4-ethylenedioxythiophene or electron-accepting pyridine and 1,3,4-oxadiazole moieties

One serious problem associated with polyfluorene and derivatives (PFs) as blue luminescent polymers is the significant energy barrier for hole or electron injections; thus they usually face charge injection and transport difficulties with the currently available cathode and anode materials. The incorporation of an electron-donating or -accepting unit is expected to improve the recombination of the charge carriers. In this paper, we apply quantum-chemical techniques to investigate three fluorene-based copolymers, copoly(2,5-ethylenedioxythiophene-alt-9,9'-dimethylfluorene) (PEF), copoly(2,5-pyridine-alt-9,9'-dimethylfluorene) (PPyF), and poly[(fluorene-2,7-diyl)-alt-(1,3,4-oxadiazole-2,5-diyl)] (PFO), in which Delta(H)(-)(L) [the energy difference between the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO), when n = infinity], the lowest excitation energies (E(g)), ionization potentials (IP), electron affinities (EA), and lambda(abs) and lambda(em) are fine-tuned by the regular insertion of electron-donating unit 3,4-ethylenedioxythiophene (EDOT) or electron-withdrawing units pyridine and 1,3,4-oxadiazole. The results show that the alternate incorporation of electron-donating moiety EDOT increases the HOMO energy and thus reduces the IPs, and consequently the hole injection was greatly improved. On the other hand, even though both kinds of charge carriers will improve the electron-accepting ability, the results show that electron-withdrawing moieties greatly facilitate the electron-transporting. Especially in PFO, the highly planar structural character resulted from the strong push-pull effect between the fluorene ring and the 1,3,4-oxadiazole ring and a weak interaction between the nitrogen and oxygen atoms in 1,3,4-oxadiazole ring and the hydrogen atom of the fluorene ring, significantly lowering the LUMO energy levels and thus improve the electron-accepting and transporting properties by the low LUMO energy levels.     

Synthesis and optical and electrochemical properties of novel copolymers containing alternating 2,3‐divinylquinoxaline and hole‐transporting units

For the enhancement of charge affinity, electron‐affinitive 2,3‐divinylquinoxaline and a series of hole‐transporting chromophores (iminodibenzyl, phenothiazine, dihexyloxybenzene, and didodecyloxydistyrylbenzene) were incorporated alternately into the polymeric main chain. The resulting copolymers ( P1 – P4 ) were basically amorphous materials and were thermally stable below 300 °C. The electronic structures, photoluminescence, and electrochemical properties of these copolymers were mainly determined by the electron‐donating chromophores in the backbone. They showed significant positive solvatochromism in formic acid. An electrochemical study revealed that they exhibited lower band gaps (<2.3 eV) due to alternating donor and acceptor conjugated units (push–pull structure). Single‐layer light‐emitting diodes of aluminum, P1 – P4 , and indium tin oxide glass were fabricated, and preliminary electroluminescence spectra showed that P1 , P3 , and P4 were orange‐emitting materials. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4570–4580, 2002     

Synthesis and optical and electrochemical properties of copolymers consisting of 9,9‐dihexylfluorene and aromatic triazole chromophores

Aromatic triazole chromophores were incorporated into polyfluorene in an attempt to increase electron affinity, to promote emission efficiency, and to diminish excimer formation. Poly(9,9‐dihexylfluorene) ( P1 ) and new copolymers with aromatic triazoles ( P2 – P4 ) were prepared by Suzuki coupling polymerization. In P2 , the aromatic triazole (3.8 mol %) was attached exclusively as terminal groups, whereas P3 and P4 were main‐chain copolymers containing 3.9 and 10.3 mol % aromatic triazole chromophores, respectively. The copolymers were soluble in common organic solvents and showed high decomposition temperatures (437–458 °C). The twisted structure between the triazole and fluorene increased the emission efficiency and effectively prevented excimer formation in P2 – P4 . After the introduction of the triazole units, the absorption spectra showed a blueshift (from 388 to 381 nm in chloroform) due to confined conjugation, but the photoluminescence spectra remained almost the same (417–418 nm); this was attributed to oligofluorene segments. No emission of triazole fluorophores was observed because of efficient energy transfer from the triazole to oligofluorene segments. However, incomplete energy transfer was observed in CH₃COOH. The optical stability upon thermal annealing was also improved by the incorporation of aromatic triazole segments. From cyclic voltammetry results, P2 – P4 , containing triazole groups, showed greater electron affinity (lowest unoccupied molecular orbital level = ?2.67 to ?2.71 eV) than P1 (?2.52 eV). Electroluminescence devices of P1 – P4 all exhibited excimer emissions (483–521 nm), which could also be diminished by the introduction of aromatic triazole chromophores. © 2006Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 136–146, 2007     

Highly efficient and stable blue‐light‐emitting copolyfluorene consisting of carbazole,oxadiazole, and charge‐trapping anthracene groups

This article presents the synthesis and electroluminescent (EL) properties of a stable blue‐light‐emitting copolyfluorene ( P1 ) consisting of carbazole, oxadiazole and charge‐trapping anthracene groups by Suzuki coupling reaction. The hole‐transporting carbazole and electron‐transporting oxadiazole improve charges injection and transporting properties, whereas the anthracene is the ultimate emitting chromophore. The thermal, photophysical, electrochemical, and EL properties of P1 were investigated by thermogravimetric analysis, differential scanning calorimeter, optical spectroscopy, cyclic voltammetry, and EL devices fabrication and characterization. P1 demonstrated high‐thermal stability with thermal decomposition and glass tranistion temperatures above 400 and 145°C, respectively. In film state, P1 showed blue emission at 451 nm attributed to anthracene chromophore. Photophysical and electrochemical investigations demonstrate that effective energy transfer from fluorene to anthracene segments and charges trapping on anthracene segments leads to efficient and stable blue emission originating from anthracence. Polymer light‐emitting diodes using P1 as the emitting layer (ITO/PEDOT:PSS/ P1 /Ca/Al) exhibited excellent current efficiency (5.1 cd/A) with the CIE coordinate being (0.16, 0.11). The results indicate that copolyfluorene is a promising candidate for the blue‐emitting layer in the fabrication of efficient PLEDs. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and properties of fluorine‐containing poly(aryl ether oxadiazole)s

Fluorine‐containing poly(aryl ether 1,3,4‐ozadiazole)s were synthesized by the nucleophilic aromatic substitution reaction of 2,5‐bis(2,3,4,5,6‐pentafluorophenyl)‐1,3,4‐oxadiazole and various bisphenols in the presence of potassium carbonate. The polymerizations were carried out at 30 °C in 1‐methyl‐2‐pyrrolidinone to avoid the gelation caused by a crosslinking reaction at para and ortho carbons to the 1,3,4‐oxidiazole ring. The obtained polymers were all para‐connected linear structures. The obtained fluorine‐containing poly(aryl ether 1,3,4‐ozadiazole)s showed excellent solubility and afforded tough, transparent films by the solution‐casting method. They also exhibited a high glass transition temperature depending on the molecular structure, and the glass transition temperature could be controlled by the bisphenols in the range of 157–257 °C. They showed good thermal stability and excellent hydrophobicity due to the incorporation of the 2,3,5,6‐tetrafluoro‐1,4‐phenylene moiety. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2855–2866, 2007     

Improved EL efficiency of fluorene‐thieno[3,2‐b]thiophene‐based conjugated copolymers with hole‐transporting or electron‐transporting units in the main chain

New electroluminescent polymers (poly(9,9′‐dioctylfluorene‐co‐thieno[3,2‐b]thiophene‐co‐benzo[2,3,5]thiadiazole) ( P1) and poly(9,9′‐dioctylfluorene‐co‐thieno[3,2‐b]thiophene‐co‐benzo[2,3,5]thiadiazole‐co‐[4‐(2‐ethylhexyloxyl)phenyl]diphenylamine ( P2) ) possess hole‐transporting or electron‐transporting units or both in the main chains. Electron‐deficient benzothiadiazole and electron‐rich triphenylamine moieties were incorporated into the polymer backbone to improve the electron‐transporting and hole‐transporting characteristics, respectively. P1 and P2 show greater solubility than poly(9,9′‐dioctylfluorene‐co‐thieno[3,2‐b]thiophene ( PFTT ), without sacrificing their good thermal stability. Moreover, owing to the incorporation of the electron‐deficient benzothiadiazole unit, P1 and P2 exhibit remarkably lower LUMO levels than PFTT , and thus, it should facilitate the electron injection into the polymer layer from the cathode electrode. Consequently, because of the balance of charge mobility, LED devices based on P1 and P2 exhibit greater brightness and efficiency (up to 3000 cd/m² and 1.35 cd/A) than devices that use the pristine PFTT . © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 243–253, 2006     

Synthesis and characterization of novel poly(p‐phenylenevinylene) derivatives containing phenothiazine‐5‐oxide and phenothiazine‐5, 5‐dioxide moieties

PPV‐based copolymers containing phenothiazine‐5‐oxide and phenothiazine‐5, 5‐dioxide moieties have been successfully synthesized by Wittig‐Horner reaction and characterized by means of UV‐vis, photoluminescence, electroluminescence spectra, and cyclic voltammetry. All of these copolymers can be dissolved in common organic solvents such as chloroform, tetrahydrofuran, and toluene. The PL maxima in the film state are located at 582, 556, and 552 nm for P1, P2, and P3, respectively. The HOMO and LUMO levels of P2 are found to be ?5.21 and ?2.68 eV, respectively; whereas those of P3 are found to be ?5.26 and ?2.71 eV, respectively. The cyclic voltammetry result indicates that the conversion of electron‐donating sulfide to electron‐withdrawing sulfoxide or sulfone group in polymers plays a dominating role in increasing its oxidation potential. Yellowish‐green light ranging from 568 to 540 nm was observed for the single layer device with the configuration of ITO/Polymer/Ca/Al. Double layer devices with Zn (BTZ)₂ as a hole blocking layer exhibited enhanced EL performance compared to the single layer devices. The maximum brightness of the double layer devices of P1, P2, and P3 is 278, 400, and 796 cd/m², respectively. The results of EL and electrochemical analyses revealed that they are promising candidate materials for organic, light‐emitting diodes with hole‐transporting ability. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4291–4299, 2007     

Carbazole end‐capped pyrene starburst with enhanced electrochemical stability and device performance

Carbazole end‐capped starburst molecule based on pyrene core “4CzFP” was synthesized and characterized. The starburst material shows good film‐forming ability and bright blue fluorescence. In cyclic voltammetry test, 4CzFP shows a high highest occupied molecular orbital energy level of ?5.26 eV, indicating it has good hole‐injection ability. The material is quite stable under series of cyclic voltammetry scans, implying its good electrochemical stability. Single‐layered electroluminescent device takes on stable blue emission with a peak current efficiency of 0.84 cd/A. Double‐layered device by adding Poly(N‐vinylcarbazole) (PVK) as a hole‐injection layer does not show any improvement, indicating that 4CzFP could be efficiently used as the hole‐injection/light‐emitting layer. The device performance is largely improved by adding a thin TPBI electron‐injection/transporting layer. The peak efficiency reaches 3.28 cd/A and the maximum brightness is over 2200 cd/m². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010