Improvement in crystallinity and optical properties of ZnO epitaxial layers by thermal annealed ZnO buffer layers with oxygen plasma

ZnO epitaxial layers with treated low-temperature (LT) ZnO buffer layers were grown by plasma-assisted molecular beam epitaxy (PA-MBE) on p-type Si (1 0 0) substrates. The LT-ZnO buffer layers were treated by thermal annealing in O₂ plasma with various radio frequency (RF) power ranging from 100 to 300 W before the ZnO epilayers growth. Atomic force microscopy (AFM), high-resolution X-ray diffraction (HR-XRD), and room-temperature (RT) photoluminescence (PL) were carried out to investigate their structural and optical properties. The surface roughness measured by AFM was improved from 2.71 to 0.59 nm. The full-width at half-maximum (FWHM) of the rocking curve observed for ZnO (0 0 2) XRD and photoluminescence of the ZnO epilayers was decreased from 0.24° to 0.18° and from 232 to 133 meV, respectively. The intensity of the XRD rocking curve and the PL emission peak were increased. The XRD intensity ratio of the ZnO (0 0 2) to Si substrates and PL intensity ratio of the near-band edge emissions (NBEE) to the deep-level emissions (DLE) as a function of the RF power was increased from 0.166 to 0.467 and from 2.54 to 4.01, respectively. These results imply that the structural and optical properties of ZnO epilayers were improved by the treatment process.     

Effect of Asi on the optical properties of Ga1−xInxAs/InP grown by molecular beam epitaxy

This report focuses on the effect of the As species and the V/III ratio on the optical properties of Ga_1−xIn_xAs/InP grown by molecular beam epitaxy (MBE). The band gap energies of the layers were measured by low temperature photoluminescence (PL) while the indium contents x were determined by X-ray for samples in the investigated range of 0.50<x<0.56. For the analysis of these data we considered the model of Kuo et al. which we confined with a correction for the different measurement temperatures in PL (4.2 K) and X-ray (300 K). Using As₄ with an effective V/III ratio higher than 1.3, we find the best agreement of the band gap energies and predictions of the theory. A lower V/III ratio always implies a reduction of the band gap energy to values 5-15 meV lower than expected. In contrast, using As₂ the PL data fit quite well independent of the effective V/III ratio above unity.     

Transmission electron microscopy observation of GaAs/Al0.3Ga0.7As T-shaped quantum well structure fabricated by glancing angle molecular beam epitaxy on GaAs(100) reverse-mesa etched substrates

GaAs/Al_0.3Ga_0.7As multi-layer structures were grown on GaAs (100) reverse-mesa etched substrates by glancing angle molecular beam epitaxy (GA-MBE). A(111)B facet was formed as a side-facet. Surface migration of Ga and Al atoms from the (100) flat region to the (111)B side-facet region has been investigated to fabricate T-shaped GaAs/AlGaAs quantum wells (QWs) under the condition that Ga and Al atoms impinge only an the (100) flat region and do not impinge on the (111)B side-facet. Observation of T-shaped GaAs/AlGaAs quantum wires (QWRs) by cross-sectional transmission electron microscopy (TEM) revealed that there is no migration of Al atoms from the (100) to the (111)B facet region at a substrate temperature (T_s) as high as 630°C, under a V/III ratio of 28 (in pressure ratio). On the other hand, very thin GaAs epitaxial layers grown on the (111)B side-facet region owing to the Ga migration were observed for substrate temperatures of 600 and 630°C. It was found that the mass flow of Ga atoms from the (100) region to the (111)B side-facet region increases, with the thermal activation energy of 2.0 eV, as the substrate temperature increases from 570 to 630°C. The GA-MBE growth on a reverse-mesa etched GaAs substrate at a low temperature 570°C or lower is desirable to fabricate a nm-scale GaAs/AlGaAs QWR structure with nm-scale precision.     

Formation of Ge-diffusion-suppressed GaAs layers and InAs quantum dots on Ge/Si substrates

Crystal growth of GaAs layers and InAs quantum dots (QDs) on the GaAs layers was investigated on Ge/Si substrates using ultrahigh vacuum chemical vapor deposition. Ga-rich GaAs with anti-site Ga atoms grown at a low V/III ratio was found to suppress the diffusion of Ge into GaAs. S-K mode QD formation was observed on GaAs layers grown on Ge/Si substrates with Ga-rich GaAs initial layers, and improved photoluminescence from 1.3 μm-emitting InAs QDs was demonstrated.     

Growth of (1 0 1¯ 3¯ ) semipolar GaN on m-plane sapphire by hydride vapor phase epitaxy

The crystalline, surface, and optical properties of the (1 0 1¯ 3¯) semipolar GaN directly grown on m-plane sapphire substrates by hydride vapor phase epitaxy (HVPE) were investigated. It was found that the increase of V/III ratio led to high quality (1 0 1¯ 3¯) oriented GaN epilayers with a morphology that may have been produced by step-flow growth and with minor evidence of anisotropic crystalline structure. After etching in the mixed acids, the inclined pyramids dominated the GaN surface with a density of 2×10⁵ cm⁻², revealing the N-polarity characteristic. In the low-temperature PL spectra, weak BSF-related emission at 3.44 eV could be observed as a shoulder of donor-bound exciton lines for the epilayer at high V/III ratio, which was indicative of obvious reduction of BSFs density. In comparison with other defect related emissions, a different quenching behavior was found for the 3.29 eV emission, characterized by the temperature-dependent PL measurement.     

In-situ photoluminescence and capacitance-voltage characterization of InAlAs/InGaAs regrown heterointerfaces by molecular beam epitaxy

This paper characterizes the electronic properties of InAlAs/InGaAs molecular beam epitaxy (MBE) regrown interfaces by combined use of in-situ photoluminescence surface state spectroscopy (PLS³) and capacitance-voltage (C-V) techniques. It is shown that the interface state density at the continuously grown InAlAs/InGaAs interface is low and comparable with that of the uninterrupted AlGaAs/GaAs interface, and that the effect of the growth interruption was surprisingly small, whereas the same interruption resulted in almost 10² times reduction of the PL efficiency for the AlGaAs/GaAs system. It is also shown that a high density of surface states exists at the MBE InGaAs surface. Interruption after the growth of the bottom InAlAs layer in the InAlAs/InGaAs/InAlAs system also leads to appreciable generation of interface states, but it is much smaller as compared with the case of the AlGaAs/GaAs/AlGaAs system.     

The influence of the growth rate and V/III ratio on the crystal quality of InGaAs/GaAs QW structures grown by MBE and MOCVD methods

The influence of the growth rate and V/III ratio on the crystal quality of In_0.2GaAs/GaAs quantum well structures was examined. The investigated heterostructures were grown by molecular beam epitaxy (MBE) and metalorganic chemical vapour deposition (MOCVD). Reflection high energy electron diffraction (RHEED), photoluminescence measurements (PL), high-resolution X-ray diffraction (HRXRD) and atomic force microscopy (AFM) were applied for evaluation of the interfaces smoothness and the overall layer quality. Comprehensive characterisation of InGaAs/GaAs structures allowed us to establish optimal values of analysed technological parameters. Moreover, the comparison between the results obtained for samples grown by two different epitaxial techniques allowed us to find, which of the analysed growth parameters has the strongest influence on the quality of MBE and MOCVD grown structures. In contrast with the growth temperature and the interruption time, which in different manner impact on the crystal quality of QWs obtained by different method, the growth rate and the V/III ratio play similar role in both epitaxial techniques.     

固态源MBE系统生长高质量的调制掺杂GaAs结构材料和InP/InP外延材料的兼容性研究

通过固态源的分子束外延系统生长了调制掺杂AlGaAs/GaAs结构材料和InP/InP外延材料.在生长含磷材料之后,生长条件(真空状态)变差;我们通过采取合理的工艺方法和生长工艺条件的优化,获得了电子迁移率为1.86×105cm2/Vs(77K)调制掺杂AlGaAs/GaAs结构材料和电子迁移率为2.09×105cm2/Vs(77K)δ-Si掺杂AlGaAs/GaAs结构材料.InP/InP材料的电子迁移率为4.57×104 cm2/Vs(77K),该数值是目前国际报道最高迁移率值和最低的电子浓度的InP外延材料.成功地实现了在一个固态源分子束外延设备交替生长高质量的调制掺杂AlGaAs/GaAs结构材料和含磷材料.     

New aluminium precursors for MOMBE (CBE): a comparative study

Recently different new Al precursors have been developed to improve the electrical and optical quality of AlGaAs layers grown by MOMBE (CBE), since AlGaAs layers still suffer from the high incorporation of oxygen and carbon. Three approaches are introduced and results obtained from Al_xGa_1−xAs layers (0 < x ≤ 1) are discussed. APAH, a double ring structure molecule, was found to yield AlGaAs layers with high contents of carbon and nitrogen. The use of an Alane-adduct decreases impurity concentrations and improves optical properties. However, TIBAl is superior and provides highest PL response together with carrier concentrations below p = 10¹⁶ cm^-3. Even though the concept of coordinative saturation is promising, results achieved by TIBAl showed that trialkyls could also be well suited for AlGaAs, assuming that they are properly synthesized.     

HigHighly strained InGaAs/GaAs quantum wells emitting beyond 1.2 µm

Highly strained In_xGa_1–xAs quantum wells (QWs) with GaAs barriers emitting around 1.2 µm are grown on GaAs substrates by metal organic vapour phase epitaxy (MOVPE) at low growth temperatures using conventional precursors. The effects of growth temperature, V/III ratio and growth rate on QW composition and luminescence properties are studied. The variation of indium incorporation with V/III ratio at a growth temperature of 510 °C is found to be opposite to the results reported for 700 °C. By an appropriate choice of the growth parameters, we could extend the room temperature photoluminescence (PL) wavelength of InGaAs/GaAs QWs up to about 1.24 µm which corresponds to an average indium content of 41% in the QW. The results of the growth study were applied to broad area laser diodes emitting at 1193 nm with low threshold current densities. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth and characterization of GaAs layers on polished Ge/Si by selective aspect ratio trapping

Epitaxial GaAs layers have been deposited on polished Ge film grown on exactly (0 0 1) oriented Si substrate by metal-organic chemical vapor deposition (MOCVD) via aspect ratio trapping (ART) method. Double-crystal X-ray diffraction shows that the full-width at half-maximum (FWHM) of the (4 0 0) reflection obtained from 1 μm GaAs is 140 arcsec. Scanning electron microscopy (SEM) of the GaAs layer surface shows that the amount of antiphase domain defects (APD) raised from GaAs/Ge interface using Ge ART on Si is dramatically reduced compared to GaAs layers grown on exact (0 0 1) Ge substrate. Defect reduction and Ge diffusion at vicinal GaAs/Ge interface were investigated via cross-section transmission electron microscopy (X-TEM) and secondary ion mass spectrometry (SIMS). Film morphology and optical properties were evaluated via SEM and room temperature photoluminescence (PL).     

Raman Scattering Studies on the Thin Graded Band Gap AlGaAs Hetero-Epitaxial Layer

Thin graded hetero-epitaxial AlGaAs layer has been grown from the undersaturated Liquid Phase Epitaxial (LPE) technique. The grown layers have been characterized using Laser Raman scattering studies. The peak position and intensity ratio of GaAs and AlAs like LO phonon frequencies have been measured and compared with conventional LPE grown AlGaAs epitaxial layer. The behaviour of GaAs and AlAs like LO phonons has been found to vary with the aluminum composition in the grown layer. Raman peak positions have been observed to shift to lower wavenumber in GaAs like LO phonon and higher wavenumber side of AlAs like LO phonon. Aluminum free features have been noticed in IEE grown AlGaAs (x > 0.8) hetero epitaxial layers.     

Se-doped AlGaAs grown on GaAs(111)A by molecular beam epitaxy

The electrical properties of Se-doped Al_0.3Ga_0.7As layers grown by molecular beam epitaxy (MBE) on GaAs(111)A substrates have been investigated by Hall-effect and deep level transient spectroscopy (DLTS) measurements. In Se-doped GaAs layers, the carrier concentration depends on the misorientation angle of the substrates; it decreases drastically on the exact (111)A surface due to the re-evaporation of Se atoms. By contrast, in Se-doped AlGaAs layers, the decrease is not observed even on exact oriented (111)A. This is caused by the suppression of the re-evaporation of Se atoms, by Se---Al bonds formed during the Se-doped AlGaAs growth. An AlGaAs/GaAs high electron mobility transistor (HEMT) structure has been grown. The Hall mobility of the sample on a (111)A 5° off substrate is 5.9×10⁴ cm²/V·s at 77 K. This result shows that using Se as the n-type dopant is effective in fabricating devices on GaAs(111)A.     

The electrical, optical and crystalline properties of GaAs: C grown by GSMBE using TMG and AsH3 for application to HBTs

We report the results of a comprehensive study on the electrical, optical and crystalline properties of heavily carbon doped p-type (100) GaAs epilayers (p = 6.3 × 10¹⁸−1.3 × 10²⁰ cm^-3; THICKNESS = 250−420 nm) grown by gas source molecular beam epitaxy using trimethylgallium and arsine. X-ray analysis showed epilayer lattice contraction with a mismatch of δa/a = -1.8 × 10^-3 at p = 1.3 × 10²⁰ cm^-3. Room temperature photoluminescence peak energy shifted from 1.40 eV (p = 6.3 × 10¹⁸ cm^-3) to 1.37 eV (p = 1.3 × 10²⁰ cm^-3). Stokes Raman spectra showed two modes assigned as the unscreened LO phonon (292 cm^-1) and the low frequency branch of the coupled hole-plasmon-LO-phonon (266 cm^-1). Conservation of Raman scattering rules under all incident light configurations showed that the (100) GaAs:C epilayers were of high crystalline quality without the presence of faceting or other such crystalline defects. Annealing at 900°C for between 30 s to 45 min, resulted in a significant reduction in the hole concentration, lattice contraction and photoluminescence intensity for all epilayers. The implications of these results for the development of GaAs/AlGaAs HBTs are discussed.     

Structural and optical properties of quaternary AlInGaN epilayers grown by MOCVD with various TMGa flows

AlInGaN quaternary epilayers have been grown with various TMGa flows by metalorganic chemical vapor deposition to investigate the influence of growth rate on the structural and optical properties. Triple-axis X-ray diffraction measurements show AlInGaN epilayers have good crystalline quality. Photoluminescence (PL) measurements show that the emission intensity of AlInGaN epilayers is twenty times stronger than that of AlGaN epilayer with comparable Al content. V-shaped pits are observed at the surface of AlInGaN epilayers by atomic force microscopy (AFM) and transmission electron microscopy (TEM). High growth rate leads to increased density and size of V-shaped pits, but crystalline quality is not degraded.     

Liquid phase epitaxy (LPE) of GaN on c- and r-faces of AlN substrates

We present the optical properties of MBE-grown GaAs–AlGaAs core–shell nanowires (NWs) grown on anodized-aluminum-oxide (AAO) patterned-Si (1 1 1) substrate using photoluminescence and Raman scattering spectroscopy. The GaAs NWs were grown via the vapor–liquid–solid method with Au-nanoparticles as catalysts. Enhancement in emission of at least an order of magnitude was observed from the GaAs–AlGaAs core–shell NWs as compared to the bare GaAs NWs grown under similar conditions, which is an indication of improved radiative efficiency. The improvement in radiative efficiency is due to the passivating effect of the AlGaAs shell. Variation in bandgap emission energy as a function of temperature was analyzed using the semi-empirical Bose–Einstein model. Results show that the free exciton energy of the GaAs core–shell agrees well with the known emission energy of zinc blende (ZB) bulk GaAs. Further analysis on the linear slope of the temperature dependence curve of photoluminescence emission energy at low temperatures shows that there is no difference between core–shell nanowires and bulk GaAs, strongly indicating that the grown NWs are indeed predominantly ZB in structure. The Raman modes show downshift and asymmetrical broadening, which are characteristic features of NWs. The downshift is attributed to lattice defects rather than the confinement or shape effect.     

GaAs---InP heteroepitaxy and GaAs---InP MESFET fabrication by MOVPE

Lattice-mismatched heteroepitaxy has attracted considerable attention in recent years. A great interest of these systems is the possibility of integrating devices from different materials on a single substrate. 1.3 and 1.5 μm InGaAs(P)/InP laser diodes are essential for optical communication, whereas InP field effect transistor technology is less developed than that of GaAs MESFET. The performances of laser diodes are much more sensitive to a high density of disclocations, so it would be interesting to grow GaAs MESFET on InP for integration with 1.3 and 1.5 μm lasers. Due to the large difference of the thermal expansion coefficient and lattice parameter between GaAs and InP, it is very difficult to grow GaAs epilayers of high quality on it is very difficult to grow of GaAs epilayer high quality on InP substrates due to the large difference of the thermal expansion coefficient and lattice parameter between GaAs and InP. A new method, metalorganic source modulation epitaxy (MOSME), which improves the crystal quality of GaAs epilayers on InP substrates by MOVPE, has been adopted in our laboratory. The lowest full width at half maximum (FWHM) of the double crystal X-ray (DCX) diffraction spectra reaches as low as 120 arcsec for a 5 μm thick layer. Structural properties (misorientation, lattice parameters and crystal quality) of 1.0–5.0 μm thick GaAs layers grown on InP have been measured by DCX diffraction. On GaAs MESFETs grown on InP, we have measured g_m = 100 ms/mm. For these transitions, the current gain cut-off frequency (F_t) is around 12 GHz and the maximum frequency of oscillation (F_max) is higher than 30 GHz.     

The effect of inserting strain-compensated GaNAs layers on the luminescence properties of GaInNAs/GaAs quantum well

Photoluminescence (PL) properties of GaInNAs/GaAs quantum wells (QWs) with strain-compensated GaNAs layers grown by molecular beam epitaxy are investigated. The temperature-dependent PL spectra of GaInNAs/GaAs QW with and without GaNAs layers are compared and carefully studied. It is shown that the introduction of GaNAs layers between well and barrier can effectively extend the emission wavelength, mainly due to the reduction of the barrier potential. The PL peak position up to 1.41 μm is observed at the room temperature. After adding the GaNAs layers into QW structures, there is no essential deterioration of luminescence efficiency. N-induced localization states are also not remarkably influenced. It implies that with optimized growth condition, high-quality GaInNAs/GaAs QWs with strain-compensated GaNAs layers can be achieved.     

MOVPE growth of GaAs on Ge substrates by inserting a thin low temperature buffer layer

High quality GaAs layers have been grown by low pressure MOVPE on Ge(001) and Ge(001) 9° off oriented in [110] direction by using a thin low temperature (LT) GaAs layer. Investigations of the initial growth step were performed at different V/III ratios and temperatures. To show the good buffer layer quality solar cell structures were grown on off oriented n‐Ge(001) and n‐GaAs(001) substrates. The surface morphology was studied by atomic force microscopy which showed the step‐flow growth mode on 1.2 µm thick GaAs/Ge structures. The crystalline qualities of this structures and the smooth surface morphology were investigated by double crystal X‐ray diffraction (XRD) and atomic force microscopy (AFM). (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth of heavily C-doped GaAs/AlGaAs MQW structures by MOVPE for 2–3 μm normal incidence photodetectors

The growth and intersubband optical properties of high quality heavily doped p-type GaAs/AlGaAs multiple quantum well (MQW) structures are reported. The MQWs were fabricated by the atmospheric pressure metalorganic vapor phase epitaxy process using liquid CCl₄ to dope the wells with C acceptors (N_a ≈ 2 × 10¹⁹ cm⁻³). A constant growth temperature was maintained for the entire structure while different V/III ratios were used for the well and barrier regions. By this process it is possible to achieve both high C doping densities in the wells and to simultaneously obtain good quality AlGaAs barriers. Fourier transform infrared spectroscopy measurements on heavily doped 10-period MQW structures reveal a new absorption peak at 2 μm with an effective normal incidence absorption coefficient of 4000 cm⁻¹. Photocurrent measurements on mesa-shaped diodes show a corresponding peak at 2.1 μm. The photodiodes exhibit a symmetrical current-voltage characteristic and a low dark current, which are indicative of a high quality MQW structure and a well-controlled C doping profile. The 2 μm absorption represents the shortest wavelength ever reported for any GaAs/AlGaAs or InGaAs/AlGaAs MQW structure and should be very useful for implementing multicolor infrared photodetectors.