Diffusion technique for the generation of gaseous halogen standards

Halogens are known to play an important role in the tropospheric ozone-depletion chemistry and are of special interest because of their influence on the atmospheric oxidation capacity. In this paper, we investigate the application of a capillary diffusion technique for the generation of gaseous halogen standards like Br₂, IBr, ICl and I₂. The influence of capillary dimension (i.e. length and inner diameter), ambient pressure and headspace volume of the diffusion vessel on the test gas output has been evaluated. The experimental output rates are determined from the mass loss of the analyte vessel on a regular schedule and compared with their respective theoretical predictions. We also demonstrate that a 1,3,5-trimethoxybenzene-coated diffusion denuder is capable of collecting gaseous ICl quantitatively, which provides an attractive alternative for the rapid determination of the output of test gas devices. The output rates of ICl measured by the denuder method are in close agreements with the data obtained by the gravimetric method.     

Heterogeneous reactions of HOI, ICl and IBr on sea salt and sea salt proxies

The heterogeneous chemistry of HOI, ICl and IBr on sea salt and sea salt proxies has been studied at 274 K using two experimental approaches: a wetted wall flow tube coupled to an electron impact mass spectrometer (WWFT-MS) and an aerosol flow tube (AFT) coupled to a differential mobility analyser (DMA) and a chemical ionisation mass spectrometer (CIMS). Uptake of all three title molecules into bulk aqueous halide salt films was rapid and controlled by gas phase diffusion. Uptake of HOI gave rise to gas-phase ICl and IBr, with the latter being the predominant product whenever Br(-) was present. Only partial release of IBr was observed due to high solubility of dihalogens in the film. ICl uptake gave the same yield of IBr as HOI uptake. Uptake of ICl on NaBr aerosol was accommodation limited with alpha = 0.018 +/- 0.004 and gas phase IBr product has a yield of 0.6 +/- 0.3. The results show that HOI can act as a catalyst for activation of bromine from sea-salt aerosols in the marine boundary layer, via the reactions: HOI(aq) + Cl + H--> ICl(aq) + H(2)O(l) and ICl(aq) + Br--> IBr(aq) + Cl.     

Wet effluent parallel plate diffusion denuder coupled capillary ion chromatograph for the determination of atmospheric trace gases

We describe an inexpensive, compact parallel plate diffusion denuder coupled capillary IC system for the determination of soluble ionogenic atmospheric trace gases. The active sampling area (0.6x10 cm) of the denuder is formed in a novel manner by thermally bonding silica gel particles to the surface of Plexiglas plates. The effluent liquid from the parallel plate diffusion denuder is collected and preconcentrated on a capillary preconcentrator column before analysis using a capillary ion chromatograph. Using SO(2) as the test gas, collection efficiency is essentially quantitative at air sampling rates up to 500 ml min(-1). The system provides a limit of detection (LOD) of 1.6 parts per trillion for SO(2) for a 10 min sampling period.     

A study of the atmospherically important reactions of dimethylsulfide (DMS) with I2 and ICl using infrared matrix isolation spectroscopy and electronic structure calculations

The reactions of dimethylsulfide (DMS) with molecular iodine (I(2)) and iodine monochloride (ICl) have been studied by infrared matrix isolation spectroscopy by co-condensation of the reagents in an inert gas matrix. Molecular adducts of DMS + I(2) and DMS + ICl have also been prepared using standard synthetic methods. The vapour above each of these adducts trapped in an inert gas matrix gave the same infrared spectrum as that recorded for the corresponding co-condensation reaction. In each case, the infrared spectrum has been interpreted in terms of a van der Waals adduct, DMS?:?I(2) and DMS?:?ICl, with the aid of infrared spectra computed for their minimum energy structures at the MP2 level. Computed relative energies of minima and transition states on the potential energy surfaces of these reactions were used to understand why they do not proceed further than the reactant complexes DMS?:?I(2) and DMS?:?ICl. The main findings of this research are compared with results obtained earlier for the DMS + Cl(2) and DMS + Br(2) reactions, and the atmospheric implications of the conclusions are also considered.     

Evaluation of denuder sampling for a mixture of three common gaseous diisocyanates

A denuder sampler has been evaluated for a mixture of three gaseous diisocyanates, i.e. toluene diisocyanate (TDI), hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI). Sampling was performed at a total concentration of diisocyanates close to the Swedish occupational exposure limit (OEL), which is 10 ppbv (69-92 microg m(-3)), for a 5-min period. The denuder tube was coated with a chemosorptive stationary phase consisting of SE-30 (polydimethylsiloxane) and the derivatising reagent dibutylamine (DBA). It was shown that the denuder has a collection efficiency for HDI and IPDI comparable to that of an impinger method, while sampling of TDI resulted in an 8% lower concentration. Both short-term (15 min) and long-term (8 h) sampling periods were shown to yield reproducible results. For 8-h measurements, a sampling flow rate of 5 mL min(-1) was shown to be suitable for the investigated concentration range, i.e. 10-100 ppbv (69-921 microg m(-3)). A flow rate of 25 mL min(-1) or higher resulted in breakthrough after 8 h due to chromatography of the compounds in the adsorbent. The limit of detection (LOD) for the air sampling method is nearly 500 times lower than the OEL. The denuder tubes can be prepared at least 10 days prior to sampling without degradation of performance. Furthermore, they can be stored up to 6 days in a freezer after sampling without significant loss of analytes.     

Reaction of Trimethylbenzene over Alumina-Pillared Montmorillonite

The reaction of trimethylbenzene (TMB) over alumina-pillared montmorillonite (Al-PM) had been investigated in a fixed-bed flow reactor at 300 °C and atmospheric pressure. Al-PM calcined in the range 300-500 °C exhibited decreased layer distance, surface area and acid amount. The strong acid sites of Al-PM calcined at 500 °C were greatly diminished according to measurements of ammonia temperature-programmed desorption. Under our conditions the reaction proceeded mainly via isomerization and disproportionation with little dealkylation. The conversion of reactant decreased in the order 1,2,3-TMB ≥ 1,2,4-TMB > 1,3,5-TMB and the selectivity of isomerization in the order 1,2,3-TMB > 1,3,5-TMB > 1,2,4-TMB, corresponding to the order of diminishing thermal instability. Both the catalytic activity and the selectivity ratio of disproportionation to isomerization decreased with increased calcined temperature and time-on-stream. o-Xylene content in the total xylene produced from 1,2,4-TMB or 1,2,3-TMB greatly exceeded the composition at thermodynamic equilibrium. These results arc consistent with the decrease of both the strong acid sites and the pore size of Al-PM which exhibits the restricted transition state selectivity.     

31P CP-MAS NMR,Vibrational, and X-Ray Characterization of the Adducts of Triphenylphosphine Sulfide with ICl and IBr

The reactions between triphenylphosphine sulfide (Ph₃PS) and ICl in CCl₄ and IBr in CH₂Cl₂ in 1 : 1 molar ratio give the solid adducts Ph₃PS · ICl ( I ) and Ph₃PS · IBr ( II ) whose structures have been solved by X-ray diffraction. Compounds I and II consist of discrete molecule units and feature the S–I–Cl or S–I–Br linear group. The S–I bond distances in I , II (2.641(1), 2.665(1) Å respectively) and in compound 2 Ph₃PS · 3 I₂ ( III ) (2.729(2) Å) are correlable to the net increase in the I–X (X = Cl, Br, I) bond distance. The structural features of I , II and III are in accordance with ³¹P CP–MAS NMR, FT-Raman and FT-IR spectral data, and elucidate the nature of the donor (Ph₃PS)-acceptor (ICl, IBr, I₂) interaction.     

Studies of microwave-enhanced Suzuki-Miyaura vinylation of electron-rich sterically hindered substrates utilizing potassium vinyltrifluoroborate

The Suzuki-Miyaura cross-coupling of sterically hindered and electron-rich ortho,ortho′-substituted aryl halides with potassium vinyltrifluoroborate utilizing microwave irradiation has been conducted while adjusting solvent ratio, irradiation time, and catalyst loading to find optimal conditions. Coupling of benzyl 3,5-bis(benzyloxy)-4-bromobenzoate leads to a mixture of the desired styrene derivative and the reduced product. 4-Bromo-1,3,5-trimethoxybenzene, methyl 4-bromo-3,5-dimethoxybenzoate, and mesitylene bromide were also coupled to test the breadth and scope of this methodology. Of these substrates tested only 4-bromo-1,3,5-trimethoxybenzene was not vinylated successfully, which is believed to be due to the electron-rich nature of this system.     

Analysis of nitrite and nitrate as 1-nitro-2,4,6-trimethoxybenzene derivatives by reversed-phase HPLC with UV-detection

Summary A reversed-phase HPLC method for the determination of nitrite and nitrate in aqueous solutions, biological buffers and human urine is described. The method is based on the conversion of nitrite and nitrate into their 1-nitro-2,4,6-trimethoxybenzene (NTBM) derivatives by using 1,3,5-trimethoxybenzene and concentrated sulphuric acid. NTMB is extracted by benzene, the solvent evaporated, the residue reconstructed in methanol/water (3/4, v/v) and subsequently analyzed by reversed-phase HPLC and UV detection (360 nm). The specificity of the nitration reaction, good reproducibility (C.V. 6.2%) and high sensitivity (8.4 ng nitrite) show the applicability of this method to the quantitative analysis of nitrite and nitrate in several matrices including human urine.     

Annular diffusion denuder for simultaneous removal of gaseous organic compounds and air oxidants during sampling of carbonaceous aerosols

A specially designed annular diffusion denuder for simultaneous removal of organic gaseous compounds and atmospheric oxidants in carbonaceous aerosol sampling is presented. Various kinds of denuder coatings were compared with respect to the collection efficiency of both organic gaseous compounds and NO₂ and ozone. The optimum sorbent is a mixture of activated charcoal and sulfite on molecular sieve. To ensure high collection efficiency over long-term field operation, two annular diffusion denuders are combined in series. The first half of the first denuder is filled with Na₂SO₃ on molecular sieve (23 cm long layer) while the second half of the first denuder and the whole second denuder are filled with activated charcoal (the total length of the charcoal section is 67 cm).     

“Badge-type” passive sampler for monitoring ambient ammonia concentrations

A passive “badge-type” sampling device for the determination of gaseous ammonia was developed. The collection substrate is phosphoric acid. The sampler can be used for outdoor and indoor sampling of ammonia in the concentration range from 0.05 μg/m³ to 10 mg/m³. The performance was tested in the laboratory and in the field against an annualar denuder, a filter pack and an impinger technique. The intercalibration showed that the passive sampler compares very well with active samplers (r²=0.99; k=1.05). The average reproducibility of the sampler was 8%. Hence the badge sampler is well suited for the determination of ammonia in a wide range of concentrations and particularly for application under rural background conditions. The sampling rate of the device was calculated according to a simple multi-layer model.     

制备2,4,6-三甲基苯甲醛的新方法

1,3,5-三甲苯与溴素在水溶液中反应生成2,4,6-三甲基溴苯(1,收率90%);1制备成格氏试剂再与甲醛反应得到2,4,6-三甲基苄醇(2,收率79%)。2经铬酸氧化得2,4,6-三甲基苯甲醛(3,收率90.3%)。3的总收率达64.2%,纯度97%。2和3的结构经1H NMR和MS确证。     

Sodium dithionite initiated fluoroalkylation of trimethoxybenzenes, mesitylene and pyrroles with BrCF2CF2Br

Sodium dithionite initiated reaction of 1,2-dibromotetrafluoroethane with 1,3,5-trimethoxybenzene (1a) in an acetonitrile-water mixture proceeded efficiently at ambient temperature to give 1-(2-bromotetrafluoroethyl)-2,4,6-trimethoxybenzene (2) almost quantitatively. Similar reaction with 1,2,3-trimethoxybenzene (1b) gave only reasonable yield of regioisomers of (2-bromotetrafluoroethyl)-trimethoxybenzenes 3 and 4 and small amount of a substitution product of the central trimethoxy group, 1-(2-bromotetrafluoroethyl)-2,6-dimethoxybenzene (5). The reaction with mesitylene (6) gave complex mixtures from which, depending on the temperature and a mesitylene/BrCF₂CF₂Br ratio, the expected (2-bromotetrafluoroethyl)mesitylene (8) or a dimeric product, 4,4′-bis(2-bromo-1,1,2,2-tetrafluoroethyl)-1,3,5,1′,3′,5′-hexamethylbicyclohexyl-2,5,2′,5′-tetraene (7), were isolated in a yield of 18 and 13%, respectively. The reactions of BrCF₂CF₂Br with pyrrole (9) and 1-methylpyrrole (11) gave the respective alkylated compounds, 2-(2-bromotetrafluoroethyl)pyrrole (10) and 2-(2-bromotetrafluoroethyl)-1-methylpyrrole (12) in over 70% yields; the former was found to be fairly unstable. The reactivity of the terminal bromine atom in 1-(2-bromotetrafluoroethyl)-2,4,6-trimethoxybenzene (2) was also investigated.     

Studies on silyl furans. II. Halodesilylation of 2-trimethylsilyl-3,4-bis(methoxycarbonyl)furans

Reactions of 2-trimethylsilyl-3,4-bis(methoxycarbonyl)furans 1a,b with sulfuryl chloride, bromine, and iodine monochloride in acetonitrile afforded the corresponding 2-halo-3,4-bis(methoxycarbonyl)furans 2a-f via chloro-, bromo-, and iododesilylation in good yields, respectively. However, the reaction of 1a with bromine in carbon tetrachloride mainly gave 2-bromo- 2b and 2-bromo-5-trimethylsilyl-3,4-bis(methoxycarbonyl)furan ( 3 ) in 37% and 45% yields. Similarly, the reaction of 1a with iodine monochloride afforded 1a , 2-chloro- 2a and 2-iodo-3,4-bis(methoxycarbonyl)furan ( 2c ) in 50%, 27%, and 23% yield.     

Freezing halide ion solutions and the release of interhalogens to the atmosphere

The effect of freezing on a variety of acidified and neutral, nitrite ion and halide-containing mixtures has been investigated using UV/vis spectroscopy. Several trihalide ions were formed and monitored, including I(2)Cl(-), I(2)Br(-), ICl(2)(-) and IBr(2)(-). A mechanism to explain the observations is given in terms of steps involving INO and the nitroacidium ion, [H(2)ONO](+). The transformation of sea salt components to specific trihalide ions by freezing represents a potentially important process in a polar atmospheric context. This is because the dichloro- and dibromo-trihalide ions can release chlorine- and bromine-containing gases, which are key intermediates in ozone destruction.     

Photodissociation dynamics of IBr(-)(CO(2))(n), n<15

We report the ionic photoproducts produced following photoexcitation of mass selected IBr(-)(CO(2))(n), n=0-14, cluster ions at 790 and 355 nm. These wavelengths provide single state excitation to two dissociative states, corresponding to the A(') (2)Pi(1/2) and B 2 (2)Sigma(1/2) (+) states of the IBr(-) chromophore. Excitation of these states in IBr(-) leads to production of I(-)+Br and Br(-)+I( *), respectively. Potential energy curves for the six lowest electronic states of IBr(-) are calculated, together with structures for IBr(-)(CO(2))(n), n=1-14. Translational energy release measurements on photodissociated IBr(-) determine the I-Br(-) bond strength to be 1.10+/-0.04 eV; related measurements characterize the A(') (2)Pi(1/2)<--X (2)Sigma(1/2) (+) absorption band. Photodissociation product distributions are measured as a function of cluster size following excitation to the A(') (2)Pi(1/2) and B 2 (2)Sigma(1/2) (+) states. The solvent is shown to drive processes such as spin-orbit relaxation, charge transfer, recombination, and vibrational relaxation on the ground electronic state. Following excitation to the A(') (2)Pi(1/2) electronic state, IBr(-)(CO(2))(n) exhibits size-dependent cage fractions remarkably similar to those observed for I(2) (-)(CO(2))(n). In contrast, excitation to the B 2 (2)Sigma(1/2) (+) state shows extensive trapping in excited states that dominates the recombination behavior for all cluster sizes we investigated. Finally, a pump-probe experiment on IBr(-)(CO(2))(8) determines the time required for recombination on the ground state following excitation to the A(') state. While the photofragmentation experiments establish 100% recombination in the ground electronic state for this and larger IBr(-) cluster ions, the time required for recombination is found to be approximately 5 ns, some three orders of magnitude longer than observed for the analogous I(2) (-) cluster ion. Comparisons are made with similar experiments carried out on I(2) (-)(CO(2))(n) and ICl(-)(CO(2))(n) cluster ions.     

Inductively Coupled Plasma Etching in ICl- and IBr-Based Chemistries. Part II: InP, InSb, InGaP, and InGaAs

A parametric study of Inductively Coupled Plasma (ICP) etching of InP, InSb, InGaP, and InGaAs has been carried out in ICl/Ar and IBr/Ar chemistries. Etch rates in excess of 3.1 for InP, 3.6 for InSb, 2.3 for InGaP, and 2.2 m/min for InGaAs were obtained in IBr/Ar plasmas. The ICP etching of In-based materials showed a general tendency: The etch rates increased substantially with increasing ICP source power and rf chuck power in both chemistries, while they decreased with increasing chamber pressure. The IBr/Ar chemistry typically showed higher etch rates than ICl/Ar, but the etched surface morphologies were fairly poor for both chemistries.     

Ab initio thermochemistry involving heavy atoms: an investigation of the reactions Hg + IX (X = I, Br, Cl, O)

Accurate 0 K enthalpies have been calculated for reactions of mercury with a series of small iodine-containing molecules (I2, IBr, ICl, and IO). The calculations have been carried out with the coupled cluster singles and doubles method with a perturbative correction for connected triple excitations [CCSD(T)] using sequences of correlation consistent basis sets and accurate relativistic pseudopotentials. Corrections have been included to account for core-valence correlation, spin-orbit coupling, scalar relativity, and the Lamb shift. In a few cases coupled cluster calculations with iterative triple (CCSDT) and quadruple (CCSDTQ) excitations have been carried out to estimate the effects of higher order electron correlation. The pseudopotential calculations have also been compared to all electron calculations using second- and third-order Douglas-Kroll-Hess Hamiltonians. In addition to the reaction enthalpies, heats of formation, bond lengths, and harmonic vibrational frequencies have been calculated for the stable triatomic products HgI2, HgIBr, HgICl, and HgIO. Accurate dissociation energies, equilibrium bond lengths, and harmonic vibrational frequencies have also been calculated for each of the diatomic molecules involved in this study (HgI, HgBr, HgCl, HgO, I2, IBr, ICl, and IO). The reported enthalpies are expected to have accuracies of 1 kcal/mol or better.     

Kinetics study of the aromatic bicyclic peroxy radical + NO reaction: overall rate constant and nitrate product yield measurements

The measurements of the overall bicyclic peroxy radical + NO rate constant for the 1,3,5-trimethylbenzene (1,3,5-TMB) system and of the nitrate product yields for the benzene, toluene, p-xylene, and 1,3,5-TMB systems were performed via the turbulent flow chemical ionization mass spectrometry technique. While the overall rate constant was found to be consistent with the value used in the most detailed aromatic oxidation kinetic model (Master Chemical Mechanism, MCM), the nitrate product yields were found to be generally lower than predicted by the MCM and to have a different aromatic species-specific dependence than the MCM predicts.     

A new ozone denuder for aerosol sampling based on an ionic liquid coating

A new ionic liquid 1-octyl-3,5-dimethylpyridinium iodide ([O35LUT]⁺[I]⁻) was synthesized and utilized as coating for an ozone denuder device based on a high-volume aerosol sampler (30 m³ h⁻¹). Particle transmission of the denuder was studied, and over 99% of particles ranging from 10 to 2,500 nm were transmitted. The device, containing 4.66 g of ionic liquid, was used outdoors, under dry and damp atmospheric conditions. In order to expose the device to an average concentration of 120 ppbv (240 μg m⁻³) of ozone in air, an additional production of ozone was directly injected into the denuder. Under these conditions, over 97% of ozone was removed for approximately 120 h (5 days). Therefore, iodide-based ionic liquids can be used as a new alternative to conventional denuder coatings in order to reduce artifacts occurring during sampling of particulate matter. Future applications are not limited to ozone removal for specific aerosol sampling methods.