Electropolymerization of polypyrrole, modified with germanium, on a passivated titanium electrode in aqueous nitrate solution: new results on catalytic reduction of protons and dissolved oxygen

Conductive polypyrrole (PPy) films and PPy films containing Ge microparticles were synthesized by anodic oxidation of pyrrole in acidic nitrate solutions using a bare passivated titanium electrode. Well-adhering black PPy films were obtained both under galvanostatic and potentiodynamic polarization. After the formation of the PPy film, during the first anodic cycle, an increase of the anodic deposition current with the number of cycles was observed, revealing the increase of conductivity of the growing film. The variations of the electrode surface area were estimated by impedance spectroscopy measurements. The kinetics of the PPy film formation is controlled by diffusion of the Py monomer in the solution. The diffusion coefficient, estimated by two different methods, was ca. 2×10^–6 cm² s^–1. The reduction rate of oxygen and protons at the Ti/PPy/Ge electrodes depends on how the Ge microparticles are incorporated in the PPy film. Optimum conditions for this incorporation are realized with thin PPy films and high Ge loading. Thermogravimetric analysis shows that the PPy film containing Ge microparticles is more thermally stable than the blank PPy film. Electronic Publication     

The development of conductive composite surfaces by a diffusion-limited in situ polymerization of pyrrole in sulfonated polystyrene ionomers

Electrically conductive composite surfaces were prepared by a diffusion-controlled in situ polymerization of pyrrole in the surface layer of sulfonated polystyrene ionomer films. Premolded films of the ionomer sulfonic acid derivatives were sequentially immersed in aqueous solutions of pyrrole and FeCl₃, and polymerization occurred only where both the monomer and the oxidant were present. The penetration of the polypyrrole (PPy) into the film was controlled by varying the immersion time in the monomer solution. The amount of PPy produced depended on the immersion time of the film in the monomer and the degree of sulfonation of the ionomer. Surface conductivities of 10⁻⁴-10⁻¹ S/cm were achieved with PPy concentrations from 2 to 22 wt % and composite layers as thin as 15 μm. Intermolecular interactions occurred between PPy and the ionomer by proton transfer. Incorporation of PPy also increased the tensile strength of the ionomer film, significantly increased its modulus above T_g, and inhibited melt flow. © 1997 John Wiley & Sons, Inc.     

Novel chemical synthesis of polypyrrole thin film electrodes for supercapacitor application

Present investigation describes the cost-effective, novel and simple chemical synthesis of polypyrrole (PPy) thin films for supercapacitor application. These PPy films are characterized by different techniques such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The XRD pattern reveals the amorphous nature of PPy thin film, which is highly feasible for supercapacitors. Further, FTIR study confirms the formation of PPy. The surface morphological study exhibit the coverage of uniform and smooth morphology on thin film. The electrochemical supercapacitive properties of PPy thin films are evaluated using cyclic voltammetry (CV) in 0.5 M H₂SO₄ electrolyte, which exhibits the maximum specific capacitance of 329 Fg⁻¹ at the scan rate of 5 mV s⁻¹. Additionally, an equivalent series resistance (ESR) of PPy thin films is found to be 1.08 Ω using electrochemical impedance measurement.     

Electrochemical kinetics of nanosized Ag and Ag2O thin films prepared by radio frequency magnetron sputtering

Ag and Ag₂O thin films have been prepared by radio frequency magnetron sputtering on Cu substrates and have been characterized by X-ray diffraction, scanning electron microscope and atomic force microscope. The electrochemical performance of the thin films has been studied by galvanostatic cycling and cyclic voltammetry. The potential dependence of Li-ion chemical diffusion coefficients, [(D)\tilde]_\textLi {\widetilde{D}_{\text{Li}}} , of the films has been determined by galvanostatic intermittent titration technique and electrochemical impedance spectroscopy. It is found that Li-ion chemical diffusion coefficients of the Ag film range from 10⁻¹⁶ to 3 × 10⁻¹⁴ cm² s⁻¹. The Ag/Li₂O composite that is formed from Ag₂O after the first cycle exhibits higher [(D)\tilde]_\textLi {\widetilde{D}_{\text{Li}}} values than the Ag film, especially at a low Li-intercalation content. The phase transitions in the two-phase region cause a significant decrease of chemical diffusion coefficients.     

Study on the preparation and multiproperties of the polypyrrole films doped with different ions

Conducting polypyrrole (PPy) films doped with p‐toluene solfonate (pTS^?), perchlorate (ClO₄^?) and polyphosphate (PP^?) were electrochemically synthesized on the stainless steel SS‐304 and the Indium Tin Oxide (ITO) glass substrates successfully. The conducting polymer composite films were studied by Fourier transform infrared spectra, integrated thermal analysis system and scanning electron microscopy, respectively. Four‐point probe measurements and in situ nanotribolab system equipped with a nanoscale electrical contact resistance package were employed to analyze their electrical and mechanical properties. Results indicate that the film doped with PP^? ion showed the best thermal stability. For the ClO₄^? ion doped films, the glass transition occurred at 274.8 °C. The pTS^? ion doped film on the SS‐304 steel had a good conductivity, and there was a voltage barrier that ranged from ?1.25 to 1.9 V according to the current–voltage curves. Nanoindentation tests show that the mechanical properties of the PPy/pTS^? film and the PPy/PP^? film were better than that of PPy/ClO₄^? films. Copyright © 2012 John Wiley & Sons, Ltd.     

Alkali‐treated semiconducting polypyrrole for infrared detection

A simple treatment of a polypyrrole (PPy) film with sodium hydroxide (NaOH) solutions reduces the conductivity (i.e., increased the resistance) and makes the film heat sensitive in the infrared (IR) spectrum with wavelength from 2.5 to 15.4 μm. The IR sensitivity increases with increasing treatment time in NaOH solutions and increasing exposed area to the radiation. The temperature coefficient of resistance, α, quantifying the sensitivity to IR, of the NaOH‐treated PPy is comparable with that of silicon and other conventional materials. The reduction and recovery of resistance due to IR on/off exposure exhibit a t^β dependence, where t is the time and β is determined to be around 0.5. This implies that the response of the material is controlled by diffusion of heat flux into and out of the sample. It is also observed that thermal ageing of the NaOH‐treated PPy film enhances the IR sensitivity. The sensing response of the treated films is observed beyond the thermal IR region to ultraviolet–visible wavelengths. Thus, the NaOH‐treated PPy appears to be a broadband sensing material. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Conductive Composite Materials of Polyethylene and Polypyrrole with High Modulus and High Strength

Composite films of polyethylene (PE) and polypyrrole (PPy) were prepared by polymerization of PPy on an ultradrawn polyethylene film with high modulus and high strength in ferric chloride (FeCl₃) aqueous solution. The electrical conductivity of the composite film was found to be related to the polymerization conditions, such as polymerization temperature, polymerization time, the concentration and the oxidation potential of the FeCl₃ solution. Scanning electron microscopy, FTIR and ¹³C NMR spectra were used to elucidate the morphological and structural variations of PPy prepared under different conditions, which lead to the differences in the electrical properties of the resultant composite films. The best electrical conductivity of the composite was about 5.5 S/cm for the film prepared under optimum conditions. The Young's modulus and the tensile strength reached 80 GPa and 3.2 GPa, respectively, which indicated the successful production of a conductive polymer with high strength and high modulus.     

Preparation of conductive polypyrrole (PPy) composites under supercritical carbon dioxide conditions

Electrically conductive composites were prepared via the chemical oxidative polymerization of the pyrrole monomer in polystyrene (PS) and zinc neutralized sulfonated polystyrene (Zn-SPS) films under supercritical carbon dioxide (SC-CO₂) conditions. The strong swelling effect of SC-CO₂ made polypyrrole (PPy) particles not only form on the surface, but also become incorporated into the film, resulting in a homogeneous structure with a relatively higher conductivity. By comparison, the composite prepared in aqueous solutions shows a skin-core structure and a conductivity of 3 to 4 orders of magnitude lower than that of the former due to the diffusion-controlled process of the pyrrole monomer. The percolation thresholds of PS/PPy and Zn-SPS/PPy composites were 6.2% and 2.7% of the volume fraction of PPy, respectively, much lower than the theoretically predicted value of 16%. Moreover, the conductive composites prepared under SC-CO₂ conditions showed higher thermal stability, especially in the high-temperature region. Translated from Chemical Journal of Chinese Universities, 2006, 27(4): 771–774 (in Chinese)     

ELECTRICALLY CONDUCTIVE COMPOSITE PREPARED BY ELECTROCHEMICAL POLYMERIZATION OF PYRROLE IN POLY-(p- PHENYLENE TEREPHTHALAMIDE) MATRIX

The preparation of PPy/PPTA conductive composite films by electrochemical method is presented.The first step is to cast a thin layer of poly (p-phenylene-terephthalamide) (PPTA) on a slice of Pt working electrode. The second step is to electrochemically polymerize pyrrole on the PPTA/Pt working electrode. Both of the electrical conductivity and the mechanical properties of the PPy/PPTA composite film are better than those of the pure PPy film, and the film has excellent flexibility at low temperature, even in liquid nitrogen.The SEM picture of the cross-section of PPy,/PPTA composite film showed that the two components were well mixed.Cyclic voltammograms of PPy,/PPTA film in aqueous solution showed that the conductive films could be reduced and reoxidized.     

Fabricating polypyrrole/tungsten oxide hybrid based electrochromic devices using different ionic liquids

A facile approach of polypyrrole (PPy)/tungsten oxide (WO₃) composites electrosynthesized in ionic liquids for fabrication of electrochromic devices is discussed. The electrochromic properties of PPy/tungsten oxide nanocomposite films (PPy/WO₃) prepared in the presence of four different ionic liquids, 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMIMBF₄), 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆), 1‐butyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl) imide (BMIMTFSI), and 1‐butyl‐1‐methylpyrrolidinium bis(trifluoromethylsulfonyl) imide (BMPTFSI) were investigated in detail. Cyclic voltammetry results revealed that PPy/WO₃ nanocomposite films have much more electrochemical activity than those of WO₃ and PPy film. The electrochromic contrast, coloration efficiency, and switching speed of the composite films were determined for electrochromic characteristics. The maximum contrast and the maximum coloration efficiency values were measured as 33.25% and 227.89 cm²/C for the PPy/WO₃/BMIMTFSI composite film. Copyright © 2015 John Wiley & Sons, Ltd.     

Self-assembled films based on polypyrrole and carbon nanotubes composites for the determination of Diuron pesticide

In this work, polypyrrole (PPy) and its respective composite with functionalized multi-walled carbon nanotubes (MWCNT) were obtained by chemical polymerization of the monomer pyrrole in aqueous solution. The obtained PPy as well as its composite (PPy-MWCNT) were characterized by Fourier transform infrared spectroscopy (FTIR) and were used to produce nanostructured self-assembled (SA) films deposited onto glass substrates covered with indium tin oxide (ITO). The SA films were produced with alternated layers of polystyrene sulphonated (PSS) and were characterized by UV-visible, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM) analyses. The applicability of the SA films was evaluated by square wave voltammetry (SWV) with standard additions of aliquots of Diuron pesticide in Britton-Robinson buffer solutions (pH = 2.0). The results showed an oxidation peak at 0.23 V which increases in function of the Diuron concentration for both the SA films. It was also observed that the SA film based on the composite (PPy-MWCNT/PSS) showed a peak current intensity about ten times higher in comparison with its unmodified counterpart (PPy/PSS) for a Diuron concentration of 4.29 × 10^?5 mol L^?1, indicating a synergic effect between PPy and MWCNT in the composite. The limits of quantification (LOQ) and limits of detection (LOD) were respectively 8.6 × 10^?7 mol L^?1 and 2.6 × 10^?7 mol L^?1.     

Diffusion energies of oxygen diffusing into polystyrene (PS)/poly (N‐isopropylacrylamide) composites

Diffusion coefficient of oxygen penetrating into polystyrene (PS) latex/poly (N‐isopropylacrylamide) (PNIPAM) microgel composite films were measured using Fluorescence technique. Three different (5, 15, and 40 wt%) PS content films were prepared from PS/PNIPAM mixtures. Diffusivity of PS/PNIPAM composite films were studied by diffusion measurements which were performed over the temperature range of 24–70°C. Pyrene was used as the fluorescent probe. The diffusion coefficients (D) of oxygen were determined using the Stern–Volmer fluorescence quenching method combined with Fickian transport and were computed as a function of temperature for each PS content film. The results showed that D values were strongly dependent on both temperature and PS content in the film. Diffusion energies were measured and found to be dependent on the composition of the composite films. Copyright © 2011 John Wiley & Sons, Ltd.     

Molecular probe techniques for studying diffusion and relaxation in thin and ultrathin polymer films

Two optically based, molecular probe techniques are employed to study relaxation and small-molecule translational diffusion in thin and ultrathin (thicknesses < ∼200 nm) polymer films. Second harmonic generation (SHG) is used to study the reorientational dynamics of a nonlinear optical chromophore, Disperse Red 1 (DR1) (previously shown to be an effective probe of α-relaxation dynamics) either covalently attached or freely doped in polymer films. Our studies on films ranging in thickness from 7 nm to 1 μm show little change in T_g with film thickness; however, a substantial broadening of the relaxation distribution is observed as film thickness decreases below approximately 150 nm. Experimental guidelines are given for using fluorescence nonradiative energy transfer (NRET) to study translational diffusion in ultrathin polymer films. Appropriate choice of a fluorescence donor species is important along with ensuring that diffusion is slow enough to be measured appropriately. Initial results on the diffusion of a small-molecule probe, lophine, in poly(isobutyl methacrylate) indicates that there is little change in probe diffusion coefficients in films as thin as 90 nm as compared to bulk films. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2795–2802, 1997     

Morphology and film formation of poly(butyl methacrylate)–polypyrrole core–shell latex particles

 Core–shell latex particles made of a poly(butyl methacrylate) (PBMA) core and a thin polypyrrole (PPy) shell were synthesized by two-stage polymerization. In the first stage, PBMA latex particles were synthesized in a semicontinuous process by free-radical polymerization. PBMA latex particles were labeled either with an energy donor or with an energy acceptor, in two different syntheses. These particles were used in a second stage as seeds for the synthesis of the core–shell particles. The PPy shell was polymerized around the PBMA core latex in an oxidative chemical in situ polymerization. Proofs for the success of the core–shell synthesis were obtained using nonradiative energy transfer (NRET) and atomic force microscopy (AFM). NRET gives access to the rate of polymer chain migration between adjacent particles in a film annealed at a temperature above the glass-transition temperature T _g of the particles. Slower chain migration of the PBMA polymer chains was obtained with the PBMA–PPy core–shell particles compared to rate of the PBMA polymer chain migration found with the pure, uncoated PBMA particles. This result is due to the coating of PBMA by PPy, which hinders the migration of the PBMA polymer chains between adjacent particles in the film. This observation has been confirmed by AFM measurements showing that the flattening of the latex film surface is much slower for the core–shell particles than for the pure PBMA particles. This result can again be explained by the presence of a rigid PPy shell around the PBMA core. Thus, these two complementary methods have given evidence that real core–shell particles were synthesized and that the shell seriously hinders film formation of the particles in spite of the fact that it is very thin (thickness close to 1 nm) compared to the size (750 and 780 nm in diameter) of the PBMA core. Transparency measurements confirm the results obtained by NRET and AFM. When the films are placed at a temperature higher than the T _g of PBMA, the increase in transparency is faster for films made with the uncoated PBMA particles than for films made with the coated PBMA particles. This result indicates again that the presence of the rigid PPy layer around the PBMA core reduces considerably the speed at which the structure of the film is modified when heated above the T _g of PBMA. Received: 02 September 1999 Accepted: 21 December 1999     

磺化聚芳醚酮砜/聚吡咯复合型直接甲醇燃料电池用质子交换膜的制备与性能研究

以高磺化度的磺化聚芳醚酮砜(SPAEKS)和吡咯(Py)为原料,通过原位聚合的方法制备了含有不同吡咯含量的SPAEKS/PPy复合膜.红外谱图表明SPAEKS聚合物中的磺酸基团与聚吡咯(PPy)中的亚氨基基团之间形成了强烈的相互作用.扫描电镜照片显示PPy能够均匀地分散在SPAEKS聚合物基体中,没有发生团聚现象.通过对复合膜的性能测试发现PPy的引入提高了复合膜的热稳定性,降低了复合膜的吸水率,改善了其水溶胀性.同时膜中水的脱附系数下降,提高了膜的保水能力.SPAEKS/PPy-3复合膜的甲醇渗透系数达到了1.18×10-7cm2/s,明显低于纯SPAEKS膜的8.52×10-7cm2/s,而其质子传导率虽有所降低,但在25℃和80℃仍然分别达到了0.039S/cm和0.061S/cm,能够满足质子交换膜对质子传导率的要求.研究结果表明,聚吡咯与SPAEKS中磺酸基的摩尔比为0.99的复合膜有望在直接甲醇燃料电池中得到应用.     

Role and effect of dopant ion on sorption-induced motion of polypyrrole films

The sorption-induced bending and recovery motion of PPy films containing different dopant ions have been investigated, and the interaction between water vapor and PPy was studied from sorption isotherms and kinetics. It was found that the PPy/BF₄ film exhibited the most rapid motion, and the initial speeds of bending and recovery motion were 7.9 and 5.9 mm s⁻¹, respectively. The linear expansion coefficient of the film increased in order of PPy/DBS, PPy/TsO, PPy/ClO₄, and PPy/BF₄, which is consistent with the packing density of the PPy chains (ϕ_PPy). The dual-mode sorption model applied to the isothermal sorption of water vapor to the PPy demonstrated that the Langmuir's capacity constant increased in the same order with the ϕ_PPy, while the Henry's law constant was nearly constant. The sorption kinetics obeyed Fickian despite the dimensional change of the films, and the PPy/BF₄ film had the largest diffusion coefficient of 3.13 × 10⁻⁸ cm² s⁻¹. The experimental results indicated that the kind of dopant ion was crucial to the thermodynamics and kinetics of sorption, and the quick and intensive bending motion of PPy/BF₄ films was attributed to the fast diffusion of water vapor, which caused the large dimensional change of the film.© 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2635–2642, 1998     

Electrochemical impedance studies of the undoping process of platinum phthalocyanine charge transfer microcrystals

Platinum phthalocyanine (PtPc) microcrystal films undergo three successive electrochemical oxidations. Each of these processes is associated with anion insertion or doping. The reverse process of anion insertion, undoping, has been investigated using electrochemical impedance spectroscopy and in-situ UV–vis spectroscopy. The impedance theory of conductive polymer films developed by Vorotyntsev et al. is applicable to this process. The kinetics of the undoping process depend upon the previous oxidative treatment, and thus the doping level. Three different states of the film can be demarcated, depending on the degree of oxidation (and thus the degree of doping) of the PtPc film. These are called the lightly doped, the conductive and the over-doped state, respectively. For lightly doped films, the film conductivity, the redox capacitance, the diffusion coefficient for charge transport and the rate of electrochemical reaction all decrease with decreasing potential. The film conductivity depends upon the concentration of free charge carriers. For the more highly doped conductive film, all of the above parameters are greatly enhanced, and the electrochemical reaction is accelerated and proceeds at a very high rate. The potential dependence of the redox capacitance and the diffusion coefficient depends on the type of anion. During undoping at 0 V, unusually high diffusion coefficients with a magnitude of order 10⁻² cm² s⁻¹ are observed and are attributed to the strong interactions between the electronic and ionic carriers during the phase transformation. For the over-doped film, undoping leads to an increase in the film conductivity and electrochemical reaction rate. The potential dependence of the redox capacitance and diffusion coefficients for charge transport implies strong interactions within the film. Hypsochromic shifts in UV–vis spectra with decreasing potential indicate conformational relaxation during the undoping process. SEM investigation confirms that the doped film swells during the de-doping process.     

Labeled magnetic nanoparticles assembly on polypyrrole film for biosensor applications

In recent years, conducting polymers combined with metallic nanoparticles have been paid more attention due to their potential applications in microelectronics, microsystems, optical sensors and photoelectronic chemistry. The work presented in this paper describes the preparation and characterization of a nanocomposite composed by a thin polypyrrole (PPy) film covered with an assembly of magnetic nanoparticles (NPs). The magnetic particles were immobilized on PPy films under appropriate magnetic field in order to control their organization on the PPy film and finally to improve the sensitivity of the system in potential sensing applications. The electrical properties and morphology of the resulting PPy film and the PPy film/NPs composite were characterized with cyclic voltammetry, impedance spectroscopy (IS), scanning electron microscopy (SEM), atomic force microscopy (AFM) and infra-red spectroscopy (IR). By using streptavidin labeled magnetic particles it was possible to functionalize the NPs assembly with biotin-Fab fragment K47 antibody. The designed biosensor had been successfully applied in rapid, simple, and accurate measurements of atrazine concentrations, with a significantly low detection limit of 5 ng/ml.     

The Use of Second‐Harmonic Generation to Study Diffusion through Films under a Liquid Phase

Knowledge of the diffusion of chemicals through buried films is important for a wide variety of systems—from sensing to drug delivery. Herein, we show that second‐harmonic generation (SHG) can be used to follow the diffusion through a thin film buried under a liquid in situ. More specifically, the diffusion of 4‐(4‐diethylaminostyryl)‐1‐methylpyridinium iodide through zeolite precursor films of different thickness is followed. The diffusion coefficients are calculated according to Fick’s law.     

Electrochemically Controlled Ion‐exchange Property of Carbon Nanotubes/Polypyrrole Nanocomposite in Various Electrolyte Solutions

The electrochemically controlled ion‐exchange properties of multi‐wall carbon nanotube (MWNT)/electronically conductive polypyrrole (PPy) polymer composite in the various electrolyte solutions have been investigated. The ion‐exchange behavior, rate and capacity of the electrochemically deposited polypyrrole with and without carbon nanotube (CNT) were compared and characterized using cyclic voltammetry (CV), chronoamperometry (CA), electrochemical quartz crystal microbalance (EQCM), X‐ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). It has been found that the presence of carbon nanotube backbone resulted in improvement in ion‐exchange rate, stability of polypyrrole, and higher anion loading capacity per PPy due to higher surface area, electronic conductivity, porous structure of thin film, and thinner film thickness providing shorter diffusion path. Chronoamperometric studies show that electrically switched anion exchange could be completed more than 10 times faster than pure PPy thin film. The anion selectivity of CNT/PPy film is demonstrated using X‐ray photoelectron spectroscopy (XPS).