New Potentiometric Sensor for the Determination of Bromate Ion in Drinking Water

The characteristics, performance and application of ion‐selective electrodes for bromate ion based on rhodamine B and tetrahexyl ammonium bromide as electrode‐active substances are described for the first time. These electrodes respond with sensitivities of (58.0±1.0) and (61.0±2.0) mV decade^?1 over the range 1.0×10^?8–1.0×10^?2 mol l^?1 at pH 4–9 and 4–8 and a detection limit of 6.0×10^?8 and 4.0×10^?8 mol l^?1 for rhodamine B and tetrahexyl ammonium bromide sensors, respectively. The electrodes are easily constructed at a relatively low cost, have a fast response time and can be used for a period of 3 months without any considerable divergence in potential. The proposed sensors displayed good selectivity for bromate ion in the presence of several substances and inorganic anions. Sensors were used for the direct assay of bromate ion in drinking water samples.     

Determination of ammonium ion in a flow-injection system with a gas-diffusion membrane : Selection of Optimal Conditions for the pH Indicator

The spectrophotometric determination of ammonium ion in water by flow-injection analysis with a membrane-separator and a pH indicator for detection is studied in detail. The relations derived facilitate the selection of appropriate solution compositions or the prediction of sensitivity. It is shown that 1.5×10^?5 M bromocresol purple (pH 6.8) as acceptor solution gives the maximal sensitivity in the flow system with a laboratory-made separation unit. Application of ultrasonic radiation in the separation step and the use of different flow rates for the donor and acceptor streams may result in increased permeation of ammonia and a correspondingly high sensitivity. By modifying the acceptor solution so that the sensitivity is decreased, more concentrated samples such as urine can be analyzed by direct injection without prior dilution. In this procedure, the sample rate was 60 h^?1 for ammonium concentration of more than 10^?5 M and 30–40 h^?1 for concentrations in the range 3×10^?7?10^?5 M. The detection limit was about 3×10^?7 M.     

Potentiometric sensors based on organic ion exchangers for determining tetraalkylammonium salts

Potentiometric sensors with plasticized polymer membranes based on organic ion exchangers, tetraalkylammonium dodecyl sulfates (benzyldimethyldodecylammonium, benzyldimethyltetradecylammonium, dimethyldistearylammonium), have been proposed for the determination of quaternary ammonium salts in model solutions and KATAPAV technical solutions. The thermal stability, composition, and solubility product have been estimated. It has been shown that ion associates are stable to 60?C70°C, K _S varies in the range from 2 × 10^?8 to 5 × 10^?10. The basic electrochemical parameters of the sensors have been determined as well, such as linearity ranges of the electrode function (5 × 10^?5 (5 × 10^?6)?1 × 10^?2 (1 × 10^?3) M) and slopes of the electrode functions (47?C59 mV/pc), response time (60?C90 sec), potential drift (2?C3 mV/day), operation period (3?C4 months), limits of detection for tetramethylammonium salts (1 × 10^?5?4 × 10^?7 M).     

Application of Membrane-Selective Electrodes for the Determination of Pioglitazone Hydrochloride in the Presence of Its Acid Degradant or Metformin Hydrochloride in Tablets and Plasma

Abstract

Polyvinyl chloride (PVC) membrane sensors for the determination of pioglitazone hydrochloride (PIO) and metformin hydrochloride (MET) were described by using the ion association complexes between these drugs with either sodium tetraphenyl-borate (TPB) or ammonium reineckate (RNC) counter ions. The performance characteristics of the sensors were evaluated according to IUPAC recommendations, reveal a fast, stable and linear response over the concentration range 3.162 × 10^?5 ? 1 × 10^?2 M for PIO and 1 × 10^?3 ? 1 × 10^?1 M for MET. The sensors are used for determination of PIO and MET in tablets and plasma. The developed method was found to be simple, accurate and precise when compared with the reported method.     

Arginine Determination with Ion-Selective Membrane Electrodes

Abstract

A new method for the determination of the amino acid arginine utilizes a dual enzyme catalyzed reaction monitored with an ammonium ion selective membrane electrode of the antibiotic type. The technique gives a linear correlation between arginine concentration and electrode response over the 3 × 10^?3 M to 3 × 10^?5 M range and a useful, but non-linear, response over a wider range. Major interferences are urea, K⁺, and NH₄ ⁺, but Na⁺ does not interfere in the physiological concentration range.     

Fabrication of a new nanocomposite modified carbon paste Al<Superscript>3+</Superscript>-ion selective electrode based on <Emphasis Type="Italic">N,N</Emphasis>′-dipyridoxyl (1,2-cyclohexanediamine) (PYCA) as an active material

Construction and feature of a nanocomposite modified carbon paste electrode for aluminum(III) ion determination based on N,N′-dipyridoxyl (1,2-cyclohexanediamine) (PYCA) as a novel selector material will be covered by this paper. The optimum composition, Nernstian slope/linear range/detection limit in the forms of calibration graph, response time, utilizable pH range, repeatability and precision of measurements of the aluminum(III) ion using the new fabricated Al³⁺-CPE was evaluated. The optimal composition which performed over Al⁺³ ion concentration range 1.0 × 10^?8 mol L^?1–1.0 × 10^?1 mol L^?1 with near-Nernstian slope equal 20.9 ± 0.2 mV decade^?1 and low detection limit about 5.0 × 10^?9 mol L^?1, was formed of ionophore (PYCA 3 %), binder (paraffin oil 30 %), modifier [multi-wall carbon nanotubes (MWCNTs) 1 %] & [Nanosilica (NS) 0.5 %], and inert matrix (graphite powder 65.5). The request time to give rise Nernstian response of electrode for concentrations from 1.0 × 10^?8 mol L^?1 to 1.0 × 10^?1 mol L^?1 of Al³⁺ ion solution was estimated about ~6 s. The new Al³⁺-CPE was applied in pH range 2.0–5.0 with no consequential change in potential response. To verify the selectivity of electrode toward aluminum(III) ion in the presence of different metallic cations, matched potential method was used. The obtain results in analytical applications reflect the excellent ability of this electrode to play the role as endpoint indicator electrode in both titration and direct potentiometric measurements.     

Trace Analysis of Lead and Copper Ions in Fish Tissue Using Paste Electrodes

Abstract

DNA was immobilized onto a carbon nanotube surface through cyclic voltammetry, in which paste electrode (PE) was subjected to lead and copper trace ion analysis. Optimized conditions for square‐wave stripping voltammetry were then searched. The results indicated three other linear working ranges—3–21 mg l^?1, 2–16 µg l^?1, and 3–17 ng l^?1 Pb(II) Cu(II)—within an accumulation time of 190 s in 0.1‐M ammonium phosphate electrolyte solutions of pH 10.0. At the optimized conditions, the detection limit (S/N) was pegged at 0.4 ng l^?1 (1.93×10^?12 M Pb(II) and 6.29×10^?12 M Cu(II)). And the relative standard deviation at 10 mg l^?1 Pb(II) and Cu(II) was a 0.074 and 0.069% precision, in 15 measurements. The method can be applied to assays of fish tissue.     

A nafion/crown ether film electrode and its application in the anodic stripping voltammetric determination of traces of silver

Glassy carbon electrodes are modified by coating with dicyclohexyl-18-crown-6 in Nafion-117. The electrode is used for a very sensitive anodic stripping voltammetric determination of silver. High sensitivity is obtained owing to the release of crown molecules from the silver-crown complex during the deposition. The detection limit is 2×10^?12 M after electrodeposition for 30 min. The recommended supporting electrolyte is 4×10^?3–7×10^?3 M potassium chloride in 0.01 M nitric acid with a deposition potential of ?0.30 V vs. SCE and a linear potential scan. Three typical calibration graphs were linear over the range 2×10^?11–1×10^?8 M for deposition times of 30, 20 and 8 min, respectively. The silver content of reagent-grade ammonium nitrate was found to be 0.48×10^?4% with a relative standard deviation of 3.7% (n=7) for parallel determinations.     

Nucleophilic Substitution in Dipolar Aprotic Solvents: Hexamethylphosphoric triamide

The rate of the reaction between ethyl tosylate and chloride as well as bromide ion has been measured in hexamethylphosphoric triamide in the presence of several counterions. Rate constants for the free ions at 25.0° are 14.4 mole^?1 for chloride and 2.0 mole^?1min^?1 for bromide, both independent of the cation used. The equilibrium constants for ion pair dissociation of lithium-, ammonium- and tetra-n-butylammonium chloride are 3.97 × 10^?2, 1.52 × 10^?3 and 6.36 × 10^?3 mole, and for the corresponding bromides 3.30 × 10^?2, 9.65 × 10^?3, and 9.62 × 10^?3 mole.     

Polymerization of methyl methacrylate by a charge transfer mechanism with urea and iron (III) complex

Methyl methacrylate (MMA) can be polymerized by a charge transfer complex formed by the interaction of urea, methyl methacrylate, and carbon tetrachloride (CCl₄) in a nonaqueous solvent like dimethylsulfoxide (DMSO). The rate of polymerization can be accelerated by Lewis acids like Fe³⁺. This article reports the polymerization of MMA initiated by urea and CCl₄ and accelerated with hexakisdimethylsulfoxide iron (III) perchlorate, [Fe(DMSO)₆](ClO₄)₃, and A at 60°C. Definite induction periods were observed for the polymerization reaction initiated by urea and CCl₄ alone, but the induction period completely vanished when the molar ratio of urea to A reached 6:1. The molecular weights of the polymers with 6:1 molar ratio of urea to A were higher than with urea alone. The rate constant for the polymerization of MMA in the presence of [Fe(urea)₆]³⁺ was 1.03 × 10^?5 1 mol^?1 s^?1 at 60°C. The transfer constant for CCl₄ for polymerization with urea alone is 2.43 × 10^?3 at 60°C.     

Polymeric membrane coated graphite cesium selective electrode based on 4′,4″(5′) di–tert-butyl di-benzo-18-crown-6

A new PVC membrane coated graphite electrode for cesium ion based on 4′,4″(5′)di–tert-butyl di-benzo-18-crown-6 (DTBDB18C6) as ionophore was prepared. The electrode shows a near Nernstian response of 57.0 ± 1.8 mV decade^?1 over a wide activity range of 6.0 × 10^?6–1.0 × 10^?1 mol L^?1 with a limit of detection 4.0 × 10^?6 mol L^?1. The proposed electrode is suitable for use in aqueous solution in the pH range of 3.0–9.5. It has a fast response time of 10 s and can be used for at least 1 month without any considerable divergence in potential. The selectivity coefficients for Cs⁺ ion with respect to ammonium, alkali, alkaline earth and some selected transition metal ions were determined and showed a superior selectivity over Li⁺, Na⁺ and alkaline earth metal ions. The new electrode was applied for determination of Cs⁺ in spiked tap water. The electrode was also used as indicator electrode in potentiometric titration of Cs⁺ with sodium tetraphenyl borate.     

Development of Polymeric Resin Ion‐exchanger Based Chloride Ion‐selective Electrode for Monitoring Chloride Ion in Environmental Water

A chloride ion‐selective electrode (ISE) membrane was developed by using a copolymeric ion‐exchanger resin (trimethyl ethenyl quaternary ammonium chloride polystyrene‐divinylbenzene copolymer resin, TMEQAC PSDVB), the ionophore ({μ‐[4,5‐Dimethyl‐3,6‐bis(dodecyloxy)‐1,2‐phenylene]}bis(mercury chloride), ETH9033), the plasticizer (bis(2‐ethylhexyl) sebacate, DOS), and the membrane substrate (polyvinylchloride, PVC). At 25 °C, the electrode exhibited an ideal Nernstian response of 59.2 mV/decade with the linear calibration concentration range from 1.0 × 10^?4‐1.0 × 10^?2 M (r² = 0.9930). The limit of detection was 2.45 ppm (6.9 × 10^?2 mM) and the measurement response time was less than 10 seconds. The working temperature range of electrode was 10‐45 °C. The working pH range for chloride ion measurement was 2.0‐11.0. Among the various anions examined in this work, only I^?, SCN^?, and MnO₄^? ions show significant interference to the electrode measurement. The chloride ISE can be used at least 72 days. The determination of chloride ion content in three kinds of environmental water sample with the electrode method was accurate (92‐95%) and precise (RSD < 4.4%) and did not show significance difference from the high‐performance liquid chromatography method.     

Ion-selective electrodes based on siderophores: Salicylate response of a ferrimycobactin membrane

Siderophores are compounds which transport iron across cell membranes; mycobactins are hydrophobic siderophores and were expected to be suitable for inclusion in the organic membrane phase of a liquid ion-exchange electrode responsive to iron(III) ions. In practice, no iron(III) response was obtained from mycobactin membranes (in a variety of solvents), but they did respond to salicylate ion with a sensitivity of 27–29 mV/decade over the range 2 × 10^?3–3 × 10^?2 mol l^?1 at pH 7. The effects of pH and interference by other anions are described and the possible mechanisms of the electrode are discussed. The selectivity of the electrode for salicylate is better than that of quaternary ammonium liquid ion-exchange electrodes.     

Determination of lipoic acid, Trolox methyl ether and tocopherols in human plasma by liquid-chromatography and ion-trap tandem mass spectrometry

A method for the simultaneous determination of lipoic acid and/or Trolox methyl ether, along with α‐, γ‐ and δ‐tocopherol was developed using liquid chromatography–tandem mass spectrometry with negative electrospray ionization (HPLC‐ESI‐MS/MS) in an ion‐trap mass spectrometer. Detection and quantification were accomplished by a multiple reaction monitoring method, using specific transitions from precursor ion to product ion for each analyte. Chromatographic separation was achieved in a 12 min run using a C₁₈‐bonded phase and methanol–aqueous ammonium acetate elution gradient. Linear correlations of the chromatographic peak area (r.u. × s^?1) to the injected amount (ng) gave the slope values (r.u. × s^?1 × ng^?1) 2.34 × 10⁴ for α‐tocopherol, 5.05 × 10⁴ for γ‐tocopherol, 1.27 × 10⁵ for δ‐tocopherol, 8.86 × 10⁵ for lipoic acid and 1.23 × 10⁵ for Trolox methyl ether. The lower limit of quantification ranged between 0.02 and 1.22 ng for Trolox methyl ether and lipoic acid. MS³ experiments of γ‐ and δ‐tocopherol suggest ion‐radical reactions and dependence of the tocopherol fragmentation pattern on the phenolic ring methylation degree. The method is shown to be applicable to measurement of these metabolites in human serum after extraction. Copyright © 2012 John Wiley & Sons, Ltd.     

A Study on Stripping Voltammetric Determination of Osmium(IV) at a Carbon Paste Electrode Modified In Situ with Cationic Surfactants

This article deals with the development of a method for the determination of osmium at a carbon paste electrode (CPE) modified with cationic surfactants of the quaternary ammonium salt type; namely, cetyltrimethylammonium bromide (CTAB) and 1‐(ethoxycarbonyl)‐pentadecyltrimethyl‐ammonium bromide (Septonex); both being added in situ and serving for preconcentration of osmium via its hexachloroosmate(IV) anion. The proper electrochemical detection was performed by cathodic scanning in the differential pulse voltammetric mode. Optimization studies concerning important experimental parameters also included a specially performed potentiometric titration, helping to define the actual stoichiometry for the ion‐pairing process, the main principle and driving force of the accumulation step. In a chloride/acetate buffer based supporting medium and with Septonex as the modifier of choice, the reduction signal for osmium was found to be proportional to the Os(IV) concentration in a range from 5×10^?9 to 5×10^?7 mol L^?1 with a limit of detection close to 5×10^?9 mol L^?1 (with preconcentration for 60 s). The method capable to determine Os(IV) in the presence of both Pt(IV) and Ir(III) was tested on model solutions as well as with real sample of industrial waste water (spiked with the analyte); both yielding the recovery rates within 88–99%.     

Some critical aspects in the determination of binding constants by electrospray ionisation mass spectrometry at the example of arsenic bindings to sulphur‐containing biomolecules

The influences of reactant concentrations, solvent type, acid strength, pH conditions and ionic strength on the determination of apparent gas‐phase equilibrium constants K using electrospray ionisation mass spectrometry (ESI‐MS) were elucidated. As example serves the interaction of the tripeptide glutathione (GSH) with phenylarsine oxide (PAO). It was shown that rising initial concentrations of both reactants were not adequately compensated by increasing signal intensities of the reaction products in the mass spectra. The equilibrium constant for the formation of the phenylarsenic‐substituted peptide species decreased from 1.42 × 10⁵ ± 1.81 × 10⁴ l µmol^?1 to 1.54 × 10⁴ ± 1.5 × 10³ l µmol^?1 with rising initial GSH concentrations from 1 to 10 µM at fixed PAO molarity of 50 µM . K values resulting from a series with a fixed GSH molarity of 5 µM and a PAO molarity varied from 10 to 100 µM remained in a narrower range between 4.59 × 10⁴ ± 2.15 × 10⁴ l µmol^?1 and 1.07 × 10⁴ ± 4.0 × 10³ l µmol^?1. In contrast, consumption numbers calculated from the ion intensity ratios of reaction products to the unreacted peptide were not influenced by the initial reactant concentrations. In a water–acetonitrile–acetic acid mixture (48:50:2, v:v), the consumption of 5 µ M GSH increased from 8.3 ± 1.4% to 39.6 ± 1.6% with increased molar excess of PAO from 2 to 20, respectively. The GSH consumption was considerably enhanced in a changed solvent system consisting of 25% acetonitrile and 75% 10 mM ammonium formate, pH 5.0 (v:v) up to 80% of the original peptide amount at an only threefold molar arsenic excess. Copyright © 2010 John Wiley & Sons, Ltd.     

Enhanced chromatographic separation of cobalt and uranyl ions using tin (IV) antimonate column from aqueous solution

The effect of electric field on tin (IV) antimonate column bed to separate cobalt and uranium was investigated. Separation was carried out from nitrate solution and ionic strength of 0.6. Variation of applied potential, time and pH were investigated. Ion mobilities at pH 1 are calculated and given to be 5.5 × 10^?4 and 2.73 × 10^?4 cm² V^?1 s^?1 for cobalt and uranyl ion respectively. Number of theoretical plate heights were calculated from the breakthrough curve and given to be 354 and 210 for cobalt and uranyl ions, respectively. Diffusion coefficient were calculated according to Nernst equation and found to be of 7.6 × 10^?6 and 3.5 × 10^?6 cm² s^?1 for cobalt and uranyl ions, respectively. Also, breakthrough capacities were calculated and found to be 0.7 mmol g^?1 for cobalt ion and 0.4 mmol g^?1 for uranyl ion, respectively.     

Electrochemical reduction of ytterbium in perchloric media

The electrochemical behavior of Yb³⁺ in perchloric media was studied by cyclic voltammetry and current reversal chronopotentiometry at several temperatures. The results show that the reversible electrochemical reduction of Yb³⁺ is followed by homogeneous reactions. The experimentally determined diffusion coefficients of ytterbic ion are 0.41×10^?5, 0.48×10^?5 and 0.53×10^?5 cm² s^?1 at 4.2, 9.2 and 14.7°C, respectively, in 0.5 M NaClO₄ solutions. From these data a value of 16 kJ mol^?1 (3830 cal mol^?1) was obtained for the activation energy for diffusion of ytterbic ion. From the activation energy the diffusion coefficient of ytterbic ion at 25.0°C was estimated. The value of 0.67×10^?5 cm² s^?1 was obtained. In all the experiments the initial pH was maintained at 4.1.     

Spectrophotometric determination of lithium ion with the chromogenic crown ether, 2″,4″-dinitro-6″-trifluoromethylphenyl-4′-aminobenzo-14-crown-4

A spectrophotometric method of determining alkali metal ions with a chromogenice crown ether reagent was found to be more selective and sensitive than an ion-pairing method based on the same size of crown ether cavity. It is shown that in the ion-pairing method, the sensitivity toward lithium ion was 5.685 × 10^?4 absorbance/mg l^?1, with sodium interfering at 300 mg l^?1. The chromogenic crown ether, 2″,4″-dinitro-6″-trifluoromeethylphenyl-4′-aminobenzo-14-crown-4, was much superior to benzo-14-crown-4. The sensitivity of the chromogenic crown ether was 1.69 × 10^?3 absorbance/mg l^?1. This represents a three-fold increase in sensitivity and less reagent is needed (2 × 10^?4 M for the chromogenic method versus 1.4 × 10^?3 M for ion-pairing). Interference from sodium decreased to 3000 mg l^?1. The reagent was used to determine lithium ion in treated blood serum samples in both a batch and flow injection method and results were compared with data obtained with atomic absorption; excellent agreement was obtained in all cases.     

Preparation and Application of Urea Electrochemical Sensor Based on Chitosan Molecularly Imprinted Films

A novel urea electrochemical sensor was constructed based on chitosan molecularly imprinted films which were prepared by potentiostatic electrodeposition of chitosan in the presence of urea followed by eluting with 0.1 M KCl. Various techniques were carried out to investigate the formation of molecularly imprinted polymer (MIP) films and the performance of the sensor. According to our expectation, the urea MIP electrochemical sensor showed excellent selectivity to urea among the structural similarities and co‐existences, high linear sensitivity to urea in the range from 1.0×10^?8 to 4.0×10^?5 M with a detection limit of 5.0×10^?9 M. Furthermore, the recovery ranged from 96.3 % to 103.3 % and therefore offered great potential for clinical diagnosis applications.