Imatinib mesylate cocrystals: synthesis, screening, and preliminary characterization

Abstract  

Drug–drug cocrystals of imatinib mesylate with several cocrystal formers, i.e. 5-chlorouracil, 5-fluorouracil, hydroxyurea, 5-fluorocytosine, N-acetylcytosine, chlorogenic acid, dacarbazine, curcumin, creatine, orotic acid, l-cysteine, glutathione, and caffeic acid, were prepared from mixtures by cogrinding or solvent cocrystallization. The samples prepared were analyzed by FTIR, DSC, and XRPD. Formation of cocrystals with different stoichiometry was observed. Novel cocrystals of imatinib mesylate with 5-fluorouracil or hydroxyurea were identified, characterized, and selected by the solid form screening approach. These cocrystals were non-hygroscopic and chemically and physically stable to thermal stress under the testing conditions.     

Thermal and structural studies of polypropylene blended with esterified industrial waste lignin

Microwave-assisted chemical modification of lignin was achieved through esterification using maleic anhydride. Modified lignin (ML) was blended in different proportions up to 25 mass% with polypropylene (PP) using Brabender electronic Plasticorder at 190 °C. The structural and thermal properties of blends were investigated by thermogravometric analysis (TG), differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD) and scanning electron microscopy (SEM). TG analysis showed increased thermal stability of blends due to antioxidant property of ML, which opposed oxidative degradation of PP. DSC analysis indicted slight depression in a glass transition temperature and melting temperature of blends due to partial miscible blend behavior between PP and ML. All blends showed higher crystallization temperatures and continuously reducing percentage crystallinity with increasing ML proportion in the blends. WAXD analysis indicated that PP crystallized in β polymeric form in addition to α-form in the presence of ML. However, proportion of β-form did not show linear relation with increase in ML proportion, thus ML acts as β nucleating agent in the PP matrix. SEM analysis showed good dispersion/miscibility in PP matrix indicating modification in lignin is useful.     

DSC and morphological studies on the crystallization behavior of β-nucleated isotactic polypropylene composites filled with Kevlar fibers

The crystallization behavior of β-nucleated isotactic polypropylene (PP) composites filled with Kevlar fibers (KFs), as well as that of non-nucleated PP/KF composites for comparison, was investigated using differential scanning calorimetry (DSC) and polarized optical microscopy (POM). The morphological observations revealed that the KF addition could induce thick α-transcrystalline layer around their surfaces in PP/KF composites, while no obvious transcrystalline layer could be detected in β-nucleated PP/KF composites. Detailed DSC investigations suggested that for the PP/KF composites, the dominant modification was α-form, and the crystallization process of matrix was promoted by KF addition, as illustrated by faster isothermal crystallization rate, shorter induction time, and higher crystallization temperature. However, for β-nucleated PP/KF composites, the main modification was β-form, and their crystallization characteristics were independent of KF addition, indicating that the α-nucleating effect of KFs was absent in this system. The DSC results were confirmed by further rheological and wide angle X-ray diffraction (WAXD) studies. The mechanism of the formation of transcrystalline layer was also discussed.     

tudy on compatibility of imatinib mesylate with pharmaceutical excipients

Differential scanning calorimetry and thermogravimetric analysis with the support of X-ray powder diffraction and infrared spectroscopy were used as screening techniques for the compatibility testing of imatinib mesylate, with following excipients: magnesium stearate, polyvinylpyrrolidone, microcrystalline cellulose. In order to maximize the probability of interactions 1:1 (by mass) drug: excipient binary mixtures were analysed and compared to individual components. Additionally an influence of storage at temperatures of 25 and 40°C on physico-chemical stability on drug – excipient binary mixtures was investigated. The largest visible changes were observed in the DSC curves of imatinib mesylate – magnesium stearate mixtures.     

The mechanism of α-γ transition of poly- (vinylidene fluoride) in the miscible blends

The simultaneous DSC-FTIR was used for the observation of crystallization and melting of poly(vinylidene fluoride) (PVDF) and its blends with poly(methyl methacrylate) (PMMA) and poly(ethyl methacrylate) (PEMA). The isothermal crystallization was carried out under the condition of both α-form and γ-form crystallized competitively. The crystal growth rate of α -form and γ -form were evaluated from the absorbance changes at 795 cm^-1 (α -form, CH₂ rocking) and 810 cm^-1 (γ -form, CH₂ rocking) obtained by the DSC-FTIR. The crystal growth rate of γ -form decreased at the same crystallization temperature in the order of PVDF/syn-PMMA, PVDF/PEMA and PVDF/at-PMMA, which was corresponding to the order of interaction parameter. The mechanism of α -g transition of PVDF in the miscible blends with at-PMMA, syn-PMMA and PEMA was evaluated from the relationship between the decrease of α -form and the increase of γ -form. The critical crystallization temperature, at which the transformation from α -form to γ -form proceeded only in the solid state, shifted to higher temperature side in the order of interaction parameter. This revised version was published online in August 2006 with corrections to the Cover Date.     

The effect of physical state on the drug dissolution rate

In this work, the enhancement of drug dissolution rate through the preparation of new formulations containing Nimodipine in molecular level dispersion or in nanodispersion into poly(vinyl pyrrolidone) (PVP) matrix, was investigated. Differential scanning calorimetry (DSC) and modulated-temperature differential scanning calorimetry (MTDSC) in combination with X-ray powder diffractometry (XRPD) and scanning electron microscopy (SEM) studies showed that Nimodipine was amorphous in solid dispersions of 10 or 20 mass%, and mainly dispersed on a molecular level. This behaviour is attributed to the strong interactions taking place between the amine group of Nimodipine and carbonyl group of PVP. At higher drug loadings, crystal reflections in XRPD patterns and melting peaks of Nimodipine in DSC traces, indicated presence of drug in crystalline form. Micro-Raman studies in combination with SEM micrographs showed that the mean particle size increases with drug content in the formulations, up to 10 μm. Moreover, both XRPD patterns and micro-Raman spectra seem to indicate that Nimodipine crystallized in a second, thermodynamically stable, crystal modification II. The physicochemical characteristics of Nimodipine and the particle size distribution directly affect the dissolution rate enhancement, which is higher in amorphous dispersions.     

Crystallization and morphology of iPP/MWCNT prepared by compounding iPP melt with MWCNT aqueous suspension

In this work, isotactic polypropylene (iPP) composites filled with multiwalled carbon nanotubes (MWCNTs) were prepared by compounding iPP melt with MWCNT aqueous suspension using a corotating twin-screw extruder, and the morphology and crystallization behavior of the composites were investigated. Scanning electron microscopy micrographs showed that MWCNTs dispersed individually at nanoscale in the iPP matrix when the MWCNTs concentration was low, though MWCNTs aggregates were detected when the filler concentration increased. The results of differential scanning calorimetry, wide-angle X-ray diffraction, and polarized light microscopy indicated that the β-form crystal of iPP was induced by MWCNTs at the concentration of 0.1 wt.% which was dispersed individually in the iPP matrix. At higher content, however, MWCNTs acted as α-nucleating agent, and the crystals in the iPP/MWCNT composites showed higher degree of perfection than that of pure iPP though smaller in dimension. Crystallization rate of iPP increased significantly with increasing MWCNT content.     

Physicochemical characterization of dipeptidyl peptidase-4 inhibitor alogliptin in physical mixtures with excipients

Alogliptin (ALG) is a hypoglycemic drug used in diabetes which inhibits the enzyme dipeptidyl peptidase-4 (DPP-4), preventing the degradation of incretins, stimulating insulin secretion. The physicochemical characteristics of ALG were evaluated by differential scanning calorimetry (DSC), thermogravimetry (TG) and scanning electron microscopy equipped with energy-dispersive X-ray spectrometer (SEM/EDS). The compatibility studies were carried out between ALG and excipients (physical mixtures, 1:1) using DSC, TG, diffuse reflectance Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRPD) and hot-stage microscopy. ALG presented purity near to 99%, melted in the range of 179.4–187.2 °C, followed by decomposition which started in 198.0 °C. SEM/EMS analysis of ALG presented irregular crystals and traces of impurities as copper and lead. DSC investigations obtained by physical mixtures showed minor alterations in the melting ranges of ALG with mannitol, magnesium stearate and commercial tablets. Solubilization of ALG in the fused excipient was observed by hot-stage microscopy between mannitol and ALG, and in tablets. The interaction observed in the mixture with magnesium stearate is due to the melting of the excipient and drug separately, first the excipient and then the drug. FTIR showed additional bands related to the excipients. XRPD proved that ALG has a crystal form and no alterations in the ALG profile were observed after the mixtures. ALG was compatible with all excipients tested. These results were important to understand the characteristics, stability and compatibility of the drug, and proved to be useful in preformulation studies.

     

The phase transformation of copper-oxinate crystals observed by electron microscopy

Summary The transformation of copper-oxinate dihydrates was studied by electron microscopy and electron diffraction method. The replica method was also applied. The mechanism by which the unstable α-form is transformed into the stable β-form is as follows. The deposition of unstable needle-like α-form crystal → internal transformation of the α-form and the formation of intermediate fine particles, (γ-form) → inter- and intra-particle condensation aggregation of the γ-form → formation of the plate like β-form crystal by internal transformation of the aggregates and by the cementation of dissolved part.

---

Zusammenfassung Die Umwandlung von Kupferoxynat-Dihydraten wurde mit Elektronenmikroskop und Elektronenbeugung studiert. Es wurde die Abdruckmethode angewendet. Der Mechanismus, durch welchen die instabile Alphaform in die stabile Betaform übergeht, wird verfolgt. Der Abbau der instabilen nadelf?rmigen Alphaform-Kristalle zu interner Umwandlung der Alphaform und der Bildung von einer intermedi?ren aus feinen Partikeln bestehenden Gammaform in die inter- und intrapartikul?re Kondensationsaggregation der Gammaform und schlie?lich die Bildung der pl?ttchen?hnlichen Betaform-Kristalle durch interne Umwandlung der Aggregate und durch Verkittung der gel?sten Teile wird gezeigt.

     

Effect of 4 mass% Ag addition on the thermal behavior of the Cu-9 mass% Al alloy

The effect of 4 mass% Ag addition on the thermal behavior of the Cu-9 mass% Al alloy was studied using differential scanning calorimetry (DSC), optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and X-ray diffractometry (XRD). The results showed that the presence of silver causes (Cu)-α+(α+g1)→ (Cu)-α+β transformation to occur in two stages. In the first one, part of the produced b phase combines with the precipitated Ag to give a silver-rich phase and in the second one the transformation is completed. The formation of this silver-rich phase seems to be enhanced at very low cooling rates. This revised version was published online in August 2006 with corrections to the Cover Date.     

Melting behavior of lamellae of isotactic polypropylene studied using hot-stage atomic force microscopy

The α- and β-form lamellae of isotactic polypropylene were developed at different temperatures. The melting behaviors of the lamellae were observed in real time at elevated temperatures using a hot-stage atomic force microscopy. The melting behavior of the α-form lamellae was determined by the lamellar defects. For the α-form lamellae developed at different undercoolings, the larger the undercoolings, the relatively higher amount of defect in the lamellae was observed. The lamellae with defects were melted into lamellar segments, and recrystallization took place during the heating process. The β-form lamellae had lower thermal stability, and they melted firstly and separately from that of α-form.     

Preparation and characterization of copper(II) tetrasulfonated phthalocyanine nanoparticles formed by laser ablation in poor solvents

Laser irradiation of copper(II) tetrasulfonated phthalocyanine (CuTsPc) microcrystals in poor organic solvents such as methanol, 2-methyl-2-propanol, ethanol, tetrahydrofuran, and acetone has produced CuTsPc nanoparticles with 15–112 nm in diameter. Field emission scanning electron microscopy (FESEM) images have shown the formation of CuTsPc nanoparticles in poor organic solvents used in this work. The mean diameters of CuTsPc nanoparticles obtained from transmission electron microscopy (TEM) images in methanol, 2-methyl-2-propanol, ethanol, tetrahydrofuran, and acetone were determined to be 26, 36, 35, 86, and 78 nm, respectively. A correlation between the size of CuTsPc nanoparticles and a solvent polarity could be found in this work.     

Thermodynamic behavior of lipid nanoparticles upon delivery of Vitamin E derivatives into the skin: in vitro studies

This article reports the thermodynamic changes of lipid nanoparticles (LN) upon delivery of lipophilic vitamin E derivatives to the skin. Skin penetration of α-tocopherol (α-T) and α-tocopherol acetate (α-Ta) into and across porcine ear skin was investigated in vitro using tape-stripping test in modified Franz diffusion cells. Wide angle X-ray scattering (WAXS) and differential scanning calorimetry (DSC) have been used to characterize the polymorphism of the solid matrix of LN before and after in vitro skin penetration assay. Cetyl palmitate LN with a loading capacity of 20% of vitamin E derivatives (with regard to the lipid matrix) have shown the typical β’ modification of waxes, with a crystallinity index (%CI) between 30 and 40%. Mean particle size and shelf life stability was assessed by static (laser diffractometry, LD) and dynamic (photon correlation spectroscopy, PCS) light scattering techniques. Submicron-sized LN were produced, i.e., 99% of LN showed a size below 600 nm immediately after production. A mean size between 180 and 350 nm (polydispersity index < 0.25) was obtained for LN stored at both 8 and 22 °C, and this size range was kept constant for at least 20 days of shelf life. Quantification of α-T and α-Ta in the skin using tape-stripping provided a 3.4-fold increase in the level of actives within the stratum corneum (SC) and 1.3-fold increase in the viable epidermis (VE). LN increased skin penetration of both actives, following a cumulative release during 8 h in modified Franz diffusion cells. The differences in the distribution levels observed between α-T and α-Ta when delivered via LN was due to the different thermodynamic activity of both actives, i.e., following increased partition coefficient of α-Ta into SC and VE, in comparison to α-T.     

β-Crystallisation tendency and structure of polypropylene grafted by maleic anhydride and its blends with isotactic polypropylene

Crystallization, melting and structure of three different commercial types of isotactic polypropylene (iPP) grafted by maleic anhydride (PP-g-MAH) with different maleic anhydride content (AC) and their β-nucleated versions were studied by X-ray diffractometry (WAXS), differential scanning calorimetry (DSC), polarised light microscopy (PLM) and scanning electron microscopy (SEM). The presence of maleic anhydride units disturbs the chain regularity, hereby decreases the crystallization tendency of iPP in general and the β-crystallisation ability in particular. β-modification of iPP (β-iPP) forms only in β-nucleated PP-g-MAH polymers studied if the anhydride content is not larger than 0.5 mass%. The influence of AC of PP-g-MAH on the feature the spherulitic structure is demonstrated by PLM and SEM micrographs. The β-nucleated iPP/PP-g-MAH blends containing 10 mass% PP-g-MAH crystallise predominantly in β-form independently of AC of the latter. The β-nuceated blends of iPP and PP-g-MAH with lowest AC crystallise in β-form in whole concentration range. The interaction parameter between iPP and PP-g-MAH polymers calculated by Nishi-Wang equation indicate limited interaction between the components.     

Prednisone/Cyclodextrin Inclusion Complexation: Phase Solubility,Thermodynamic, Physicochemical and Computational Analysis

Guest–host interaction of prednisone (PN) with cyclodextrins (CDs) have been investigated using phase solubility diagrams (PSD), differential scanning calorimetry (DSC), X-ray powder diffractometry (XRPD), scanning electron microscopy (SEM) and molecular mechanical modeling (MM). Estimates of the complex formation constant (K ₁₁) show that the tendency of PN to complex with CDs follows the order: β-CD>γ-CD>HP-β-CD>α-CD. At the same pH of 7.0, β-CD forms soluble 1:1 and insoluble 1:2 PN/CD complexes (B_S-type PSDs). The thermodynamic functions for 1:1 PN/β-CD estimated at pH = 7.0 (ΔG ₁₁^o=−20.8 kJ⋅mol⁻¹) show that complexation is driven by enthalpy (−30.7 kJ⋅mol⁻¹) but retarded by entropy (ΔS ₁₁^o=−33.1 J⋅mol⁻¹⋅K⁻¹) changes. The MM modeling study indicates the formation of different isomeric 1:1 complexes with CDs. PSD, DSC, XRPD, SEM and MM studies established the formation of inclusion complexes in solution and the solid state.     

Ultrasonic‐assisted synthesis of supramolecular copper (II) complex a precursor for the preparation of octahedron Cu2O nanoparticles applicable in the adsorption and photodegradation of Rhodamine B

A copper (II) supramolecular coordination complex formulated as [Cu₂(μ‐ox)₂(pyz)₃]_n ( 1 ), (pyz = pyrazine and ox = oxalate) has been synthesized under ultrasound irradiation. 1 was characterized using various techniques such as elemental analyses, Fourier‐transform infrared spectroscopy (FT‐IR), ultraviolet–visible spectroscopy (UV–Vis), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and single crystal X‐ray diffraction (SC‐XRD). A detailed magnetic characterization of complex 1 has been carried by vibrating sample magnetometer (VSM). The M‐H hysteresis loop of 1 revealed a weak ferromagnetic behavior with the highest magnetization of 0.0123 emu/g at room temperature. Compound 1 was used as an inorganic precursor to prepare Cu₂O nanoparticles through thermal decomposition at 600 °C. The obtained Cu₂O has been characterized using Fourier transform infrared spectroscopy (FT‐IR), X‐ray powder diffraction (XRPD) and scanning electron microscopy (SEM). The results of SEM showed octahedron Cu₂O nanoparticles with the edge lengths from 5–80 nm. Also, the adsorption ability and the photocatalytic activity of octahedral Cu₂O nanoparticles in the removal of rhodamine B (RB) have been investigated. The results showed that the obtained octahedral Cu₂O nanoparticles are effective in adsorption and degradation of rhodamine B from contaminated water sources. The maximum adsorption capacity and degradation efficiency of Cu₂O nanoparticles were 83.3 mg/g and 91.7%, respectively. It was also found that in comparison with the commercial Cu₂O, our fabricated Cu₂O nanoparticles exhibit higher catalytic activity.     

Physico-chemical characterization of anhydrous <Emphasis Type="Italic">D</Emphasis>-mannitol

In this work the solid-state characterization of anhydrous D-mannitol has been performed: α and β modifications can be distinguished only by XRPD and FTIR as they show melting temperature and enthalpy that are the same within the standard deviation. The understanding of the thermal behaviour of the δ form (obtained by re-crystallization in acetone) has required XRPD experiments performed at variable temperature. This form during heating undergoes a solid phase transition to α modification. By cooling a melted sample, under a wide range of experimental conditions, a very fast crystallization occurs. Independently of the starting crystal form (β or δ form), the re-crystallization of D-mannitol from melt always leads to α form.     

The polymorphism of copper-oxinate crystal

Summary a) Polymorphs Copper-oxinate dihydrate has three different crystal forms, namely, α-, γ-, Β-form. The γ-form is an intermediate crystal form in the course of the α → Β transformation in aqueous suspension. They gave three anhydrous polymorphs respectively, that is, the α′-,γ′- and Β′-forms by the dehydration and they are all transformed into the most stable anhydride (Β∼-form). The Β′-form is also precipitated directly from the solution at about boiling temperature. The relationships among the various crystal forms are also discussed. b) Crystal structure The cell dimensions of the γ-form dihydrated crystal are assumed to be a=13.10 ?. b=8.33 ?, c=9.49 ? and Β=106‡. The Β′-form anhydride has the following lattice Constants a=12.25 ?, b=3.78 ?, c=14.95 ? and Β=98.6‡ with the space group P2/c(C _2h ⁴ ).

---

Zusammenfassung a) Polymorphismus Kupferoxynat-Dihydrat hat drei verschiedene Kristall-formen, n?mlich die Alpha-, Gamma- und Beta-form. Die Gamma-Form ist eine intermedi?re Kristallform im Verlauf der Umwandlung von der Alpha- in die Beta-Form in w?\riger Suspension. Diese Umwandlungen ergeben 3 polymorphe Anhydrite, n?mlich die Alpha-, Gamma- und Beta-Form durch Dehydrierung, und sie alle gehen über in die stabilste Anhydritdibeta-Form. Die Beta-Form f?llt auch direkt aus der L?sung etwa bei der Siedetemperatur aus. Die Beziehung zwischen den verschiedenen Kristallformen wird ebenfalls diskutiert. b) Kristallstrukturen Die Parameter der Elementarzelle der Gamma-Form des dihydrierten Kristalls werden zu α=13,10 ?, b=8,3 ?, c=9,49 ? und Β=106‡ festgestellt. Die Beta-Form des Anhydrits hat die folgenden Gitterkonstanten α=12,2 ?, b=3,38 ?, c=14,95 ? und Β=98,6‡ und die Raumgruppe P2/c(C _2h ^7/4 ).

     

Sibutramine hydrochloride monohydrate

In the present work, the thermal decomposition of sibutramine hydrochloride monohydrate (SBT) (an appetite suppressant agent) was studied using differential scanning calorimetry (DSC) and thermogravimetry/derivative thermogravimetry (TG/DTG). Solid-state characterization was carried out by diffuse reflectance infrared fourier transform spectroscopy (DRIFT), scanning electron microscopy (SEM) and X-ray powder diffraction (XRPD). Isothermal and non-isothermal methods were employed to determine the kinetic data of decomposition process. From isothermal experiments, activation energy (Ea) can be obtained from slope of ln t versus 1/T, and the value obtained was 96.06 and 101.43 kJ mol⁻¹ in N₂ and air atmospheres, respectively. For non-isothermal method Ea can be obtained from plot of logarithms of heating rates, as a function of inverse of temperature, resulting in a value of 96.56 and 98.22 kJ mol⁻¹ in N₂ and air atmospheres, respectively. The compatibilities of several commonly used pharmaceutical excipients (microcrystalline cellulose, magnesium stearate, colloidal silicon dioxide, lactose monohydrate) and empty hard-gelatin capsules with SBT were evaluated using DSC. The 1:1 physical mixtures of these excipients with SBT showed physical interaction of the drug with magnesium stearate. On the other hand, DRIFT results did not evidence any chemical modifications.     

Thermally induced structural transformation in a hydrogen-bonded supramolecular single-crystal

The thermally induced structural transformation of a hydrogen-bonded crystal formed from an amphoteric molecule of 6-[2-methoxy-4-(pyridylazo)phenoxy]hexanoic acid MeO was studied using differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction measurement (XRD). Crystal form of the hydrogen-bonded crystal was measured by single crystal four circle diffractometer (Mo-K_α radiation). As a result, the crystal of MeO was stabilized by many C–H⋅⋅⋅O hydrogen bonds, and the C–H⋅⋅⋅O hydrogen bonds were broken by thermal energy reversibly. After transformation the supramolecular architecture was composed of supramolecular polymer including free-rotation pentamethylene main chains.