Effect of polyaniline as a surface modifier of TiO2 nanoparticles on the properties of polyvinyl chloride/TiO2 nanocomposites

Surface of TiO2 nanoparticles was modified with the in situ chemical oxidative polymerization of aniline. Polyaniline modified TiO2 nanoparticles (PANI-TiO2 ) were characterized with the FT-IR, XRD, SEM and TEM techniques. Results confirmed that PANI was grafted successfully on the surface of TiO2 nanoparticles, therefore agglomeration of nanoparticles decreased dramatically. Polyvinyl chloride nanocomposites filled with 1 wt% 5 wt% of PANI-TiO2 and TiO2 nanoparticles were prepared via the solution blending method. PVC nanocomposites were analyzed with FT-IR, XRD, SEM, TG/DTA, DSC and tensile test techniques. Effect of PANI as surface modifier of nanoparticles was discussed according to the final properties of PVC nanocomposites. Results demonstrated that deposition of PANI on the surface of TiO2 nanoparticles improved the interfacial adhesion between the constituents of nanocomposites, which resulted in better dispersion of nanoparticles in the PVC matrix. Also PVC/PANI-TiO2 nanocomposites showed higher thermal resistance, tensile strength and Young’s modulus compared to those of unfilled PVC and PVC/TiO2 nanocomposites.     

Au改性TiO2纳米复合物对人结肠癌细胞的光催化杀伤作用

提出了通过TiO₂表面修饰纳米Au的方法来提高纳米TiO₂光催化杀伤癌细胞的效率. 采用化学还原法合成了Au改性的TiO₂ (Au/TiO₂)纳米复合物, 并研究了不同掺杂量(1 wt%, 2 wt%, 4 wt%)的Au/TiO₂对人结肠癌LoVo细胞的光催化杀伤效应. 结果显示, Au的掺杂大大地提高了TiO₂纳米粒子光催化杀伤结肠癌LoVo细胞的效率, 而且Au掺杂量的高低影响Au/TiO₂光催化杀伤癌细胞的效率, 掺金量为2%的Au/TiO₂对结肠癌LoVo细胞具有最高的光催化杀伤效率. 在光强为1.8 mW/cm²的紫外灯(λ_max＝365 nm)下光照110 min, 50 μg/mL掺金量为2%的Au/TiO₂能够杀死所有的癌细胞, 而同样浓度的TiO₂只能杀死70%的癌细胞.     

The release of TiO2 and SiO2 nanoparticles from nanocomposites

There is a growing interest in the development of nanocomposites consisting of organic polymers and TiO₂ or amorphous SiO₂ nanoparticles. These nanoparticles may be released from nanocomposites. There is evidence that amorphous SiO₂ and TiO₂ nanoparticles can be hazardous. Thus, in the design of nanocomposites with such nanoparticles, hazard reduction extending to the full nanocomposite life cycle would seem a matter to consider. Options for hazard reduction include: changes of nanoparticle surface, structure or composition, better fixation of nanoparticles in nanocomposites, including persistent suppression of oxidative damage to polymers by nanoparticles, and design changes leading to the release of relatively large particles.     

In situ radical polymerization of methyl methacrylate in a solution of surface modified TiO2 and nanoparticles

Surface modified TiO₂ nanoparticles dissolved in toluene were encapsulated in PMMA by in situ radical polymerization of methyl methacrylate initiated by 2,2′-azobisisobutyronitrile. The surface modification of the TiO₂ nanoparticles (average diameter of 4.5 nm) was achieved by the formation of a charge transfer complex between TiO₂ nanoparticles and 6-palmitate ascorbic acid. The surface modified TiO₂/nanoparticles were characterized using UV−Vis and FTIR spectroscopy, while the obtained polymer nanocomposites were characterized using reflection and ¹H NMR spectroscopy, as well as gel permeation chromatography. The influence of the TiO₂ nanoparticles on the thermal properties of the PMMA matrix was investigated using thermo-gravimetric analysis and differential scanning calorimetry. The glass transition temperature of the polymer was not influenced by the presence of the nanoparticles while the thermal stability was significantly improved.     

Unusual Extensional Rheology and Dispersion Behavior of High Impact Polystyrene/TiO2 Nanocomposites Prepared by Melt‐Compounding

The extensional rheology and dispersion behavior of high impact polystyrene (HIPS) and HIPS/TiO₂ nanocomposites prepared by melt‐compounding were investigated. The influence of ethylene‐vinyl acetate (EVA) copolymer on the extensional rheology of HIPS/TiO₂ masterbatches was also researched. The rheological experiments investigated with Rosand Presicion Rheometer confirmed that the HIPS/TiO₂ masterbatches, the HIPS/EVA/TiO₂ masterbatches and the HIPS/TiO₂ nanocomposites with low TiO₂ loading shown different extensional rheology in comparison to the pure HIPS. Field‐emission scanning electron microscopy (FE‐SEM) shown the dispersion morphology of TiO₂ nanoparticles in HIPS based nanocomposites and indicated the influence of TiO₂ dispersion behavior on the unusual extensional rheology of HIPS nanocomposites.     

The catalytic role of oxide in the thermooxidative degradation of poly(methyl methacrylate)-TiO2 nanocomposites

The influence of TiO₂ nanoparticles on the thermal degradation of poly(methyl methacrylate) (PMMA) was investigated by TGA. The studied materials were characterized by Py-GC-MS, TEM, SEM, TGA, DSC and TGA-MS. The PMMA-TiO₂ nanocomposites were prepared by melt blending with different (5, 10, 15 and 20 wt% TiO₂) loadings. According to TGA results and to the activation energy (determined by the model-free isoconversional method of Vyazovkin), the incorporation of 5 wt% of TiO₂ nanoparticles into PMMA stabilizes it by more than 40 °C. However, for higher loading contents, a catalytic effect on the thermal decomposition was observed which increased with the oxide content. The results obtained by Py-GC-MS showed clearly that TiO₂ increases the formation of methanol, methacrylic acid and propanoic acid methyl ester during the degradation of PMMA. This catalytic effect could be explained through the interaction of the methoxy group of the methacrylate function with the hydroxyl groups present at the surface of the oxide particles.     

Conducting polyaniline-rutile TiO2 nanocomposites for the development of high-k dielectric materials

Inorganic dielectrics encapsulated in an organic matrix are showing excellent promise as novel dielectric materials. In this work, firstly highly organized crystalline nanoparticles of rutile TiO₂ were synthesized by acid hydrolysis of titanium isopropoxide at room temperature. Then we developed a novel dielectric material consisting of highly organized rutile TiO₂/polyaniline (PAni) nanocomposites by in-situ chemical oxidative polymerization. The structural, morphological, conducting, and dielectric properties of the rutile TiO₂/PAni nanoparticles have been evaluated by X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution-transmission emission microscopy (HR-TEM), four-point probe technique, CV (Capacitance versus Voltage), and Impedance analyzer. The nanocomposites show 70 times higher permittivity compared to rutile nanoparticles and much higher compared to anatase/PAni (ES) nanocomposites at 10 MHz. Large interfacial polarizations, nanostructure, and dopant levels are the key factors for the large dielectric constant of the nanocomposites. The rutile/PAni (ES) nanocomposites might see potential uses in super-capacitors, gate dielectric in transistors, and capacitive-type gas sensors.     

Evaluation of polymeric nanocomposites for the detection of toxic gas analytes

Four different metal oxide nanoparticles, copper oxide (CuO), aluminum oxide (Al₂O₃), nickel oxide (NiO), and titanium dioxide (TiO₂), were added to poly (2,5-dimethyl aniline) (P25DMA) during synthesis to create different polymer nanocomposites. These polymer nanocomposites were evaluated as potential sensing materials for six different gas analytes (acetaldehyde, acetone, benzene, ethanol, formaldehyde, and methanol). It was found that CuO did not incorporate into the P25DMA and only a small percentage of Al₂O₃ was incorporated. However, both NiO and TiO₂ were incorporated into the P25DMA at the same concentration as during the synthesis step. Overall, the type of metal oxide significantly affected the morphology of the sensing material and the amount of each analyte sorbed. For example, P25DMA doped with 5 wt% Al₂O₃ had high selectivity towards ethanol, whereas P25DMA doped with 20 wt% TiO₂ sorbed the most ethanol. However, P25DMA doped with 20 wt% TiO₂ also sorbed a high amount of formaldehyde, making P25DMA doped with 20 wt% TiO₂ less selective than P25DMA doped with 5 wt% Al₂O₃ towards ethanol with respect to formaldehyde.     

The effect of B2O3 addition on the crystallization of amorphous TiO2-ZrO2 mixed oxide

The effect of B₂O₃ addition on the crystallization of amorphous TiO₂-ZrO₂ mixed oxide was investigated by X-ray diffraction (XRD), thermogravimetric and differential thermal analysis (TG/DTA). TiO₂-ZrO₂ mixed oxide was prepared by co-precipitation method with aqueous ammonia as the precipitation reagent. Boric acid was used as a source of boria, and boria contents varied from 2 to 20 wt%. The results indicate that the addition of small amount of boria (<8 wt%) hinders the crystallization of amorphous TiO₂-ZrO₂ into a crystalline ZrTiO₄ compound, while a larger amount of boria (?8 wt%) promotes the crystallization process. FT-IR spectroscopy and ¹¹B MAS NMR results show that tetrahedral borate species predominate at low boria loading, and trigonal borate species increase with increasing boria loading. Thus it is concluded that highly dispersed tetrahedral BO₄ units delay, while a build-up of trigonal BO₃ promote, the crystallization of amorphous TiO₂-ZrO₂ to form ZrTiO₄ crystals.     

Non-isothermal crystallization kinetics of recycled PET-Si3N4 nanocomposites

Poly(ethylene terephthalate) (PET) is an important industrial material and has been widely applied in consumer products. Due to its slow crystallization rate, nanoparticles are incorporated into PET to function as heterogeneous nucleating agents. In this study, the non-isothermal crystallization behavior of recycled PET-silicon nitride (Si₃N₄) nanocomposites was investigated by differential scanning calorimetry (DSC). In the general analysis of the non-isothermal crystallization curves, it was found that the Si₃N₄ nanoparticles could effectively accelerate the nucleation of PET, but the crystal growth rate was slowed down when the Si₃N₄ content was more than 1 wt%. This might be attributed to the interaction between the PET chains and the surface-treated Si₃N₄ nanoparticles. Results obtained from Avrami and Mo treatments agreed well with the general analysis. Application of the Kissinger method and isoconversional method of Flynn-Wall-Ozawa also showed that Si₃N₄ nanoparticles had a good nucleation effect on the crystallization of PET, and the crystal growth was hindered by Si₃N₄ when the particle loading is higher than 1 wt%.     

Thermally effected structural and surface transformations of sulfated TiO2, ZrO2 and TiO2-ZrO2 catalysts

Preparations were characterized by specific surface area, thermogravimetry, and X-ray diffractometry. Thermal effects observed were (a) sulfur loss, (b) sintering, (c) crystallization and transformation of the crystalline phase(s). Thermoanalytical curves indicate that decomposition of the sulfate occurs in two distinct steps. Decrease of surface area due to (b) and (c) is concomitant to decomposition of sulfate. Sulfate was found to hinder sintering, crystallization and phase transformations of ZrO₂ and TiO₂. In low-titania and -zirconia sulfated TiO₂-ZrO₂ the minor component enhances the effect of sulfate. In equimolar TiO₂-ZrO₂ sulfate decomposition is accompanied by rapid formation of crystalline TiZrO₄.This work was supported by the MOL Rt., Hungary, which is gratefully acknowledged.     

Structural characterization and photocatalytic activity of hollow binary ZrO2/TiO2 oxide fibers

The formation of hollow binary ZrO₂/TiO₂ oxide fibers using mixed precursor solutions was achieved by activated carbon fibers templating technique combined with solvothermal process. The samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), N₂ adsorption, X-ray photoelectron spectroscopy (XPS), UV-vis, and infrared (IR) spectroscopy. The binary oxide system shows the anatase-type TiO₂ and tetragonal phase of ZrO₂, and the introduction of ZrO₂ notably inhibits the growth of TiO₂ nanocrystallites. Although calcined at 575 °C, all hollow ZrO₂/TiO₂ fibers exhibit higher surface areas (>113 m²/g) than pure TiO₂ hollow fibers. The Pyridine adsorption on ZrO₂/TiO₂ sample indicates the presence of stronger surface acid sites. Such properties bring about that the binary oxide system possesses higher efficiency and durable activity stability for photodegradation of gaseous ethylene and trichloromethane than P25 TiO₂. In addition, the macroscopic felt form for the resulting materials is more beneficial for practical applications than traditional catalysts forms.     

Effect of Surface Treatment of Titanium Dioxide Nanoparticles on Non-Isothermal Crystallization Behavior,Viscoelastic Transitions and Cold Crystallization of Poly(Ethylene Terephthalate) Nanocomposites

The effect of untreated and tri-n-octylphosphine oxide (TOPO) surface-treated TiO₂ nanoparticles when included as filler in poly(ethylene terephthalate) on its compatibility, non-isothermal crystallization behavior, viscoelastic transitions and cold crystallization has been studied. The effectiveness of the surface treatment has been studied using infrared spectrophotometry (FTIR) and thermogravimetric analysis (TGA). The effect of the untreated and surface-treated nanofiller content in the polymer, added by an extrusion process, on the non-isothermal crystallization has been studied by differential scanning calorimetry (DSC). The influence on the viscoelastic transitions and cold crystallization of PET nanocomposites has been studied through thermomechanical analysis (TMA). The surface treatment and the concentration of nanofiller influence the non-isothermal crystallization behavior, the viscoelastic transitions and the cold crystallization of the PET nanocomposites, enables us to evaluate the compatibility and the level of dispersion/aggregation of the nanofiller in the poly(ethylene terephthalate).     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

Nanocomposites of poly(l-lactide) and surface-grafted TiO2 nanoparticles: Synthesis and characterization

A new method of surface modification of TiO₂ nanoparticles by surface-grafting l-lactic acid oligomer was developed. The surface-grafting reaction was evaluated by Fourier transformation infrared (FTIR) and thermal gravimetric analysis (TGA). The results showed that l-lactic acid oligomer could be easily grafted onto the TiO₂ nanoparticles surface in the presence of stannous octanoate and the highest amount of grafted polymer was about 8.5% in weight. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) results showed that grafted TiO₂ (g-TiO₂) in chloroform or PLLA matrix approximated to uniform, while unmodified TiO₂ nanoparticles tended to aggregate. The tensile strength of this material was greatly improved by the addition of g-TiO₂ nanoparticles in poly(l-lactide) (PLLA) matrix. The tensile strength of the g-TiO₂/PLLA nanocomposite containing 5 wt.% of g-TiO₂ was 72 MPa, which was 23.1% higher than that of pure PLLA. Even though the incorporation of the TiO₂ nanoparticles into PLLA led to the deterioration of its elongation at break, the g-TiO₂/PLLA nanocomposite also exhibited better ductility than that of TiO₂/PLLA nanocomposite.     

TiO2 nanoparticles incorporated with CuInS2 clusters: preparation and photocatalytic activity for degradation of 4-nitrophenol

TiO₂ nanoparticles incorporated with CuInS₂ clusters were prepared in a solvothermal process and characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), and energy-dispersion X-ray analysis (EDX). Compared with pure TiO₂ nanoparticles, the TiO₂ nanoparticles incorporated with CuInS₂ clusters display higher photocatalytic activity with 99.9% of degradation ratio of 4-nitrophenol after 2 h irradiation. In order to investigate the effect of the CuInS₂ clusters on the photocatalytic activity of TiO₂ nanoparticles, diffuse reflectance UV–Vis spectra (DRS), photoluminescence (PL) spectra, and photocurrent action spectra were measured. The results indicate that the enhanced photocatalytic activity is probably due to the interface between TiO₂ and CuInS₂ as a trap of the photogenerated electrons to decrease the recombination of electrons and holes.     

ZrO2纳米粒子原位杂化PVDF膜的制备及其抗污染性能

针对传统聚合物膜抗污染性差的问题,本文从杂化膜结构设计出发,提出将ZrO2纳米粒子的原位制备和聚偏氟乙烯(PVDF)相转化成膜过程有机结合的制膜新方法.该方法将阴离子交换树脂引入到N,N-二甲基甲酰胺(DMF)中,以氧氯化锆为原料,利用阴离子交换树脂提供的―OH与无机盐的阴离子进行交换,得到ZrO2纳米粒子均匀分散的N,N-二甲基甲酰胺溶胶体系.随后将PVDF聚合物溶解到所得的N,N-二甲基甲酰胺溶胶体系中,获得均一、透明的铸膜液.利用X射线光电子能谱(XPS)和透射电子显微镜(TEM)对杂化膜中锆的存在状态和分散性能进行了表征.结果表明,ZrO2纳米粒子均匀分散在PVDF基体中,并且形成的纳米粒子的粒径约为10-20 nm.通过粘度、分相速度和膜形态的测定,研究了成膜机理.结果表明,ZrO2纳米粒子的引入加速了铸膜液成膜过程的分相速度.杂化膜的亲水性能通过接触角测定仪进行了评价.并选择以牛血清蛋白为代表模拟污染物,考察了杂化超滤膜的抗污染性能.结果表明,原位形成的ZrO2纳米粒子显著提高了膜的亲水性,减少了膜对蛋白质的吸附.这种将ZrO2纳米粒子的原位制备和PVDF相转化成膜过程有机结合的制膜新方法在有机-无机杂化膜的制备领域具有显著意义.     

Synthesis and characterization of conductive polyaniline/TiO2 composite nanofibers

Fibrillar conductive polyaniline/TiO₂ (PANI/TiO₂) nanocomposites with different TiO₂ amount were synthesized with a template-free in situ polymerization method and characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and conductivity measurement. The morphology determination shows that the PANI/TiO₂ composite nanofibers are relatively uniform with the diameter and length in the range of 20–40 nm and 390–420 nm respectively. It also shows that the TiO₂ of the composite is rutile crystalline and PANI has some degree of crystallinity. The IR measurement indicates that there is a strong interaction between the PANI and TiO₂ nanoparticles, and it has a beneficial effect on the thermal stability of the composite nanofiber. The conductivity of PANI/TiO₂ composites changes with TiO₂ amount and reaches an optimum value of 2.86 S/cm at 11.1 wt% TiO₂. Translated from Journal of Northwest Normal University (Natural Science), 2006, 42(4): 67–70 (in Chinese)     

Effect of different dispersing agents in the non-isothermal kinetics and thermomechanical behavior of PET/TiO2 composites

This work is based on the analysis of the influence of dispersing agents on the non-isothermal kinetics, thermomechanical behavior and dispersing action of PET/TiO₂ nanocomposites. The influence of two montanic waxes and an amide wax used as dispersing agents in the nucleating effect of the nanoparticles is studied. The dispersing agents are the following: a) a partly saponified ester of montanic acids (PSEMA), b) an ester of montanic acids with multifunctional alcohols (MAWMA) and c) an amide wax based on N,N′-Bisstearoyl ethylenediamine (AW). The non-isothermal kinetics based on the Avrami method revealed that MAWMA and PSEMA favors the nucleating effect of the nanoparticles when are included in PET. Birefringence microscopy points out the good dispersing capacity of MAWMA and AW and the termomechanical analysis confirmed that the ester of montanic acids with multifunctional alcohols MAWMA shows the best dispersing properties and best promotes the nucleating effect of the TiO₂ nanoparticles when used for PET/TiO₂ nanocomposites production.     

Opportunities and Challenges in the Use of TiO2 Nanoparticles Modified with Citric Acid to Synthesize Advanced Nanocomposites Based on Poly(amide-imide) Containing N,N′-(Pyromellitoyl)-bis-L-leucine Segments

In this study, the goal was the preparation, characterization, and surface morphology of poly(amide-imide)/TiO₂-citric acid nanocomposites (PAI/TiO₂-CA NCs). Owing to the high surface energy and tendency for agglomeration, the surface of TiO₂ nanoparticles was modified with citric acid. Then poly(amide-imide) was synthesized by direct polycondensation reaction of N,N′-(pyromellitoyl)-bis-L-leucine diacid with 4,4′-diaminodiphenylmethane by triphenyl phosphite and tetra-n-butylammonium bromide as a green medium. The attained polymer and modified TiO₂ nanoparticles were used to prepare PAI/TiO₂-CA NCs through ultrasonic irradiation. The resulting PAI/TiO₂-CA NC was characterized with FT-IR spectroscopy, X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and thermogravimetric analysis.