Role of composite MnO2 cathode on electrochemical cells based on polymer electrolyte (PEO/NaClO3)

Thin-film sodium-ion-conducting polymer electrolyte based on polyethylene oxide (PEO) system was prepared by solvent casting method. The thin-film electrolytes were characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry (CV) and alternating current conductivity, and Wagner’s polarization method. The complexation of salt with PEO was confirmed by XRD and IR studies. The charge transport of these electrolytes is mainly due to ions, which was confirmed by the transference number experiment. The conductivity studies show that the conductivity value of PEO/NaClO₃ complex increases with the increase of temperature as well as the addition of low molecular weight polyethylene glycol, dimethyl formamide, and propylene carbonate. The electrolyte stability and cell reversibility were analyzed by CV studies. Electrochemical cells have been fabricated with a common cell configuration Na|electrolyte|(MnO₂ + I₂ + C + electrolyte), and their discharge characteristic studies were made through a load 100 kΩ at room temperature. The measured open circuit voltage ranges from 2.80 to 2.54 V with short circuit current ranges from 667 to 1,000 μA and several other cell parameters were evaluated. Finally, the merit of the composite cathode is found with the comparison of the MnO₂ cathode.     

Impact of ethylene carbonate on electrical properties of PVA/(NH4)2SO4/H2SO4 proton-conductive membrane

A new proton-conductive membrane (PCM) based on poly (vinyl alcohol) and ammonium sulfate (NH₄)₂SO₄ complexed with sulfuric acid and plasticized with ethylene carbonate (EC) at different weight percent were prepared by casting technique. The structural properties of these electrolyte films were examined by XRD studies. The XRD patterns of all the prepared polymer electrolytes reveal the amorphous nature of the films. ac conductivity and dielectric spectra of the electrolyte were studied with changing EC content from weight 0.00 to 0.75 g. A maximum conductivity of 7.3 × 10⁻⁵ S cm⁻¹ has been achieved at ambient temperature for PCM containing 0.25 g of ethylene carbonate. The electrical conductivity σ, dielectric constant ε′ and dielectric loss ε″ of PCM in frequency range (100 Hz to 100 KHz), and temperature range (300–400 K) were carried out. Measurement of transference number was carried out to investigate the nature of charge transport in these polymer electrolyte films using Wagner’s polarization technique. Transport number data showed that the charge transport in these polymer electrolyte systems was predominantly due to ions. The electrolyte with the highest electrical conductivity was used in the fabrication of a solid-state electrochemical cell with the configuration (Mg/PCM/PbO₂). Various cell parameters ldensity, and current density were determined. The fabricated cells gave capacity of 650 μAh and have an internal resistance of 11.6 kΩ.     

Determination of the optimal parameters for the fabrication of ZnO thin films prepared by spray pyrolysis method

In this work, ZnO thin films have been prepared by spray pyrolysis deposition method on the glass substrates. The effect of deposition parameters, such as deposition rate, substrate temperature and solution volume has been studied by X-ray diffraction (XRD) method, UV–Vis–NIR spectroscopy, scanning electron microscopy (SEM), and electrical measurements. The XRD patterns indicate polycrystalline wurtzite structure with preferred direction along (0 0 2) planes. Thin films have transparency around 90% in the visible range. The optical band gap was determined at 3.27 eV which did not change significantly. Evolution of electrical results containing the carriers’ density, sheet resistance and resistivity are in agreement with structural results. All the results suggest the best deposition parameters are: deposition rate, R = 3 ml/min, substrate temperature, T _s = 450°C and thickness of the thin films t = 110–130 nm.     

Improvement of plasma-sprayed YSZ electrolytes for solid oxide fuel cells by alumina addition

Atmospheric plasma spray is a fast and economical process for deposition of yttria-stabilized zirconia (YSZ) electrolyte for solid oxide fuel cells. YSZ powders have been used to prepare plasma-sprayed thin ceramic films on the metallic substrate employing plasma spray technology at atmospheric pressure. Alumina doping was employed to improve the structural characteristics and electrical properties of YSZ. The effect of alumina addition from 1 to 5 wt.% on the properties of plasma-sprayed YSZ films was investigated. It was found that the gas permeability of the Al-doped YSZ electrolyte layer reached a level of 8.6 × 10⁻⁷ cm⁴ gf⁻¹ s⁻¹, which is a necessary value for the practical operation of solid oxide fuel cells. Alumina doping considerably increased the ionic conductivity of plasma-sprayed YSZ. The open circuit voltage of the alumina-doped YSZ coating was approximately equal to the theoretical value for dense YSZ material.     

Synthesis and characterization of nanoparticulate films for intermediate temperature solid oxide fuel cells

Nanocrystalline strontium-doped lanthanum manganite (LSM) with a high specific surface area of 70 m²/g was synthesized via spray pyrolysis. The as prepared powder was characterized by ex-situ X-ray diffraction (XRD), in-situ high temperature X-ray diffraction (HTXRD), ex-situ nitrogen adsorption and high resolution scanning electron microscopy (HRSEM). LSM nanopowders with a mean particle size of 40 nm were dispersed in water-based media using ultrasonication. Nanocomposite LSM-GDC (gadolinium doped ceria) thin films were prepared by single step spin coating of co-stabilized LSM and GDC dispersions. The thickness of these thin films (≤ 1 μm) is more than 10 times lower than conventional cathode layers prepared by screen printing. The interfacial polarization resistances were 68, 118 and 220 mΩ cm² at 850, 800 and 750 °C, respectively. The high performance is attributed to small grain size, high porosity and large specific surface area. This method offers a very cost effective approach for the preparation of electrochemically highly active porous thin films, particularly applicable for micro solid oxide fuel cells.     

Pulsed laser deposition of ZnO grown on glass substrates for realizing high-performance thin-film transistors

We report characterization of ZnO thin-film transistors (TFTs) on glass substrates fabricated by pulsed laser deposition (PLD). ZnO films were characterized by X-ray diffraction (XRD), atomic force microscopy and Hall effect measurements. The XRD results showed high c-axis-oriented ZnO(0002) diffraction corresponding to the wurtzite phase. Moreover, the crystallization and the electrical properties of ZnO thin films grown at room temperature are controllable by PLD growth conditions such as oxygen gas pressure. The ZnO films are very smooth, with a root-mean-square roughness of 1 nm. From the Hall effect measurements, we have succeeded in fabricating ZnO films on glass substrates with an electron mobility of 21.7 cm²/V s. By using the ZnO thin film grown by two-step PLD and a HfO₂ high-k gate insulator, a transconductance of 24.1 mS/mm, a drain current on/off ratio of 4.4×10⁶ and a subthreshold gate swing of 0.26 V/decade were obtained for the ZnO TFT.     

Reactive sputtering deposition and electrochemical characterisation of thin solid electrolyte membranes for solid oxide fuel cells

Solid oxide fuel cells directly convert the chemical energy of a fuel into electricity. To enhance the efficiency of the fuel cells, the thickness of the gastight solid electrolyte membranes should be as thin as possible. Y₂O₃-stabilised ZrO₂ (YSZ) electrolyte films were prepared by reactive sputtering deposition using Zr/Y targets in Ar/O₂ atmospheres. The films were 5 – 8 μm thin and were deposited onto anode substrates made of a NiO/YSZ composite. After deposition of a cathode with the composition La_0.65Sr_0.35MnO₃ the electrochemical properties of such a fuel cell were tested under operating conditions at temperatures between 600 °C and 850 °C. Current-voltage curves were recorded and impedance measurements were performed to calculate apparent activation energies from the fitted resistance data. The conductivity of the YSZ films varied between 4.6·10⁻⁶ S/cm and 2.2·10⁻⁵ S/cm at 400 °C and the fuel cell gave a reasonable power density of 0.4 W/cm² at 0.7 V and 790 °C using H₂ with 3 % H₂O as fuel gas. The gas compositions were varied to distinguish the electrochemical processes of the anode and cathode in the impedance spectra. Paper presented at the 8th EuroConference on Ionics, Carvoeiro, Algarve, Portugal, Sept. 16–22, 2001.     

The influence of pH electrolyte on the electrochemical deposition and properties of nickel thin films

Ni thin films were electrodeposited on gold substrate from chloride solution with different pH at room temperature. The effect of electrolyte pH on Ni coatings was studied by using the cyclic voltammetry, the scanning electron microscopy (SEM), x-ray diffraction, and alternating gradient force magnetometer measurements. From electrochemical measurements, the onset potential for reduction of Ni was gradually shifted towards more cathodic scan with increase in pH; this is due to the protons in the case of low pH values and to the hydroxide ions in the case of higher pH values. The SEM study showed that a granular and compact structure of the electrodeposited Ni layers and the variation of film morphology with bath pH are established. The x-ray diffraction spectra revealed the formation of fcc structure Ni thin films with a preferential orientation along the Ni(111). The size of the deposited crystals in both the cases has been found to be in the range of 49–153 nm. Magnetic properties such as coercivity and saturation magnetization showed strong dependence on the electrolyte solution pH and consequently the crystallite size. Coercivity higher than 130–160 Oe was achieved for a pH value of 4 to 5. The differences observed in the magnetic properties were attributed to the structural changes caused by the electrolyte pH.     

Effect of ethylene carbonate plasticizer and TiO<Subscript>2</Subscript> nanoparticles on 49% poly(methyl methacrylate) grafted natural rubber-based polymer electrolyte

The effect of plasticizer and TiO₂ nanoparticles on the conductivity, chemical interaction and surface morphology of polymer electrolyte of MG49–EC–LiClO₄–TiO₂ has been investigated. The electrolyte films were successfully prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by sol-gel process and was added into the MG49–EC–LiClO₄ electrolyte system. Alternating current electrochemical impedance spectroscopy was employed to investigate the ionic conductivity of the electrolyte films at 25 °C, and the analysis showed that the addition of TiO₂ filler and ethylene carbonate (EC) plasticizer has increased the ionic conductivity of the electrolyte up to its optimum level. The highest conductivity of 1.1 × 10⁻³ Scm⁻¹ was obtained at 30 wt.% of EC. Fourier transform infrared spectroscopy measurement was employed to study the interactions between lithium ions and oxygen atoms that occurred at carbonyl (C=O) and ether (C-O-C) groups. The scanning electron microscopy micrograph shows that the electrolyte with 30 wt.% EC posses the smoothest surface for which the highest conductivity was obtained.     

Electrical properties of cerium fluoride thin films

Thin films of ionic conductors have low internal resistance. Hence, it could be used as an electrolyte material in sensors to operate at ambient temperatures. Cerium fluoride, a unipolar fluoride ion conductor, has got a different application in electrochemical sensor. In the present work, cerium fluoride thin films have been prepared by physical vapor deposition method and their electrical properties are studied. X-ray diffraction studies reveal the polycrystalline nature of the prepared thin films and the structure of the material. Scanning electron microscopy (SEM) images show grain-like structures. Conductivity analysis of the thin films has been studied by ac impedance analysis and the maximum conductivity value is found to be 1.04 × 10⁻⁶ S cm⁻¹. The impedance spectra emphasize intergranular conduction in the prepared thin films.     

Characterisation of thin films of ceria-based electrolytes for IntermediateTemperature — Solid oxide fuel cells (IT-SOFC)

At the present, a major technological challenge for the development of solid oxide fuel cells (SOFC) is the reduction of their operation temperature in order to reduce the costs and increase the fuel cell lifetime. Nevertheless, decrease in the operating temperature leads to losses in cell performance mainly due to the ohmic drop through the electrolyte. Therefore, several approaches are currently under investigation to overcome the electrolyte problem and the use of oxygen ion conductor thin films seems to be the most promising solution. In this respect, the well-known electrolyte CeO₂-Gd₂O₃ (CGO) was investigated. Thin layers of less than 5 μm of CGO were deposited using two different techniques: RF magnetron sputtering and Atomic Layer Deposition (ALD). Physicochemical properties of the thin films obtained were characterised by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). Furthermore, impedance measurements were carried out in order to determine the electrical properties of the CGO films, in particular their ionic conductivity. Paper presented at the 9th EuropConference on Ionics, Ixia, Rhodes, Greece, Sept. 15–21, 2002.     

Performance of lithium-ion cells using 1 M LiPF<Subscript>6</Subscript> in EC/DEC (<Emphasis Type="Italic">v</Emphasis>/<Emphasis Type="Italic">v</Emphasis> = 1/2) electrolyte with ethyl propionate additive

In this work, 1 M LiPF₆:EC:DEC (v/v = 1/2) was used as a baseline electrolyte where EC is ethylene carbonate and DEC is diethyl carbonate. Ethyl propionate (EP) was used as an additive. The conductivity of the liquid electrolyte was obtained at ambient and elevated temperatures. The highest room temperature conductivity was observed at (8.05 ± 0.16) mS cm⁻¹ for the electrolyte containing 28.6 vol.% EP. Viscosity of the baseline and EP added baseline electrolytes have been measured at room and elevated temperatures. The electrolyte was also characterized by linear sweep voltammetry. The highest conducting electrolyte with 28.6 vol.% EP and the baseline electrolyte were used to fabricate several batteries. The batteries were charged and discharged at room temperature and at −20°C.     

Conductivity, dielectric behaviour and thermal stability studies of lithium ion dissociation in poly(methyl methacrylate)-based gel polymer electrolytes

Thin films of poly(methyl methacrylate) (PMMA) with lithium triflate (LiCF₃SO₃) were prepared by using the solution-casting method with PMMA as the host polymer. Ionic conductivity and dielectric measurements were carried out on these films. The highest conductivity for polymer electrolyte with a ratio of 65:35 was found to be 9.88 × 10⁻⁵ S cm⁻¹, which is suitable for the production of mobile phone battery. Thermal gravimetric analysis was carried out to evaluate the thermal stability of the polymer electrolyte. The addition of salts will increase thermal stability of the polymer electrolyte.     

Investigation on compositional effect of PEG:BaTiO<Subscript>3</Subscript> in plasticized PVC–LiBETi polymer composite electrolytes

The blend-based polymer electrolyte comprising poly(vinyl chloride) (PVC) and poly(ethylene glycol) (PEG) as host polymer and lithium bis(perfluoroethanesulfonyl)imide as complexing salt have been prepared. Ethylene carbonate and dimethyl carbonate (50:50 v/v) are used as plasticizer for the system. The barium titanate is used as a filler, and the ratio of (PEG:BaTiO₃) is varied to study its effect on the conductivity behavior of the electrolyte. XRD and ac impedance studies are carried out on the prepared samples. The ac impedance measurements show that the conductivity of the prepared samples depends on the (PEG:BaTiO₃) ratio, and its value is higher for (15:5) wt.% of (PEG:BaTiO₃)-incorporated film. The temperature dependence of the conductivity of the polymer films obeys VTF relation. The role of ferroelectric filler in enhancing the conductivity is studied. The thermal stability of the film is ascertained from TG/DTA studies. The phase morphological study reveals that the porous nature of the polymer electrolyte membranes depends on the (PEG:BaTiO₃) ratio.     

Effects of oxygen pressures on pulsed laser deposition of ZnO films

Zinc oxide (ZnO) thin films on Si (1 1 1) substrates were deposited by pulsed laser ablation of ZnO target at different oxygen pressures. A pulsed Nd:YAG laser with wavelength of 1064 nm was used as laser source. The deposited thin films have been characterized by X-ray diffraction (XRD), Atomic force microscopy (AFM), and Raman spectroscopy. XRD measurements indicate that the ZnO thin films deposited at the oxygen pressure of 1.3 Pa have the best crystalline quality. AFM results show that the surface roughness of ZnO film increases with the increase of oxygen pressure. The Raman results indicate that oxygen ambient plays an important role in removing defects due to excess zinc.     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

Role of electrolyte pH on structural and magnetic properties of Co–Fe films

Co–Fe films were electrodeposited on polycrystalline Titanium substrates from the electrolytes with different pH levels. X-ray diffraction (XRD) was used to study the crystal structure of the films. The XRD patterns showed that the films grown at the pH levels of 3.70 and 3.30 have a mixed phase consisting of face-centred cubic (fcc) and body-centred cubic, while those grown at pH=2.90 have only fcc structure. It was observed that the film composition, by energy dispersive x-ray spectroscopy, contain around 88 at% Co and 12 at% Fe for all films investigated in this study. Morphological observations indicated that all films have grainy structure with the slight change of grain size depending on the electrolyte pH. Magnetoresistance measurements, made at room temperature, showed that all films exhibited anisotropic magnetoresistance, which is affected by the electrolyte pH. From the magnetic measurements made by vibrating sample magnetometer, the saturation magnetization increases as the electrolyte pH decreases. Furthermore, all films have in-plane easy-axis direction of magnetization.     

LiPF6-EC-MPC electrolyte for LiMn2O4 cathode in lithium-ion battery

Methyl propyl carbonate (MPC) is a promising single solvent for lithium-ion battery without addition of ethylene carbonate (EC), but it is unstable upon cycling because of exposure to the spinel LiMn₂O₄ cathode. Thus, we attempted to add EC to MPC in order to form LiPF₆-EC-MPC electrolyte; the effects of solvent ratio and salt concentration on the cycling performance of LiMn₂O₄ cathode were also investigated. The experiments were characterized by conductivity measurements, charge-discharge at a constant current density and voltage–capacity curves at low temperature. To further enhance our understanding of the performance improvement of LiMn₂O₄/Li cells, the electrochemical characterization techniques (such as, LSV, EIS) were performed on these cells. The results show that the ionic conductivity of the electrolyte and the cycling performance of the spinel LiMn₂O₄ cathode have been dramatically enhanced. From the point of view of operation at low temperature (− 20 °C), 1 M LiPF₆ EC/MPC (1/3) electrolyte is highly recommended for spinel LiMn₂O₄ cathode in lithium-ion battery.     

Electrochemical deposition of quaternary Cu2ZnSnS4 thin films as?potential solar cell material

Quaternary compound semiconductor Cu₂ZnSnS₄ (CZTS), which appears to be a promising candidate for the absorber of a thin film type solar cell, was grown on polycrystalline Ag substrates by electrochemical epitaxial method. The elements were deposited in the following sequence: S/Sn/S/Cu/S/Zn/S/Cu… , the order being one cycle of SnS, one cycle of ZnS and two cycles of CuS. Morphology of the deposit has been characterized by field emission scanning electron microscopy (FE-SEM) with an energy dispersive X-ray (EDX) analyzer. X-ray diffraction (XRD) studies showed a (112) preferred orientation for the deposit. X-ray photoelectron spectroscopy (XPS) of the deposit indicated an approximate ratio 2:1:1:4 of Cu, Zn, Sn, and S, the expected stoichiometry for the deposit, and similar results have been obtained from EDX data. Near IR absorption measurements of the deposit at room temperature indicated a direct band gap of 1.5 eV, and open-circuit potential (OCP) studies indicated a good p-type property, both of which were suitable for fabricating a thin film solar cell.     

Effect of lithium salt concentration in PVAc/PMMA-based gel polymer electrolytes

Hybrid solid polymer electrolyte films comprising of poly(vinyl acetate) (PVAc), poly(methyl methacrylate) (PMMA), LiClO₄, and propylene carbonate are prepared by solution casting technique by varying the salt concentration. In this study, PVAc/PMMA polymer blend ratio is fixed as 25:75 on the basis of conductivity and mechanical stability of the film. X-ray diffraction, Fourier transform infrared impedance, thermogravimetry/differential thermal analysis and scanning electron microscopy studies are carried out for the polymer electrolytes. The maximum ionic conductivity is found to be 4.511 × 10⁻⁴ S cm⁻¹ at 303 K for the plasticized polymer electrolyte with 8 wt.% of LiClO₄. The ionic conductivity is found to decrease with an increase of LiClO₄ concentration.