Preconcentration and matrix separation of precious metals in geological and related materials using metalfix-chelamine resin prior to inductively coupled plasma mass spectrometry

A method for determining Au, Pt, Pd, Ir and Rh in ores and silicates and Fe-formation rocks is described. Sample decomposition was carried out with aqua regia and HF, followed by fusion of any insoluble residue with Na₂2O₂ in a glassycarbon crucible. The precious metals were separated, in 1.2 mol dm⁻³ HCl media, from the matrix elements by ion-exchange, using a mini-column with tetraethylenepentamine (metalfix-chelamine) resin. The resin was destroyed with HNO₃ and H₂O₂ in a high-pressure vessel assisted by microwave heating, and the precious elements were determined by flow-injection inductively coupled plasma mass spectrometry. The sample treatment, optimization of analytical variables and measurable concentration levels are discussed. The limits of quantification (10 sd_{n − 1}) calculated from a procedural blank sample solution were 4.0, 2.0, 1.5, 0.8 and 0.5 ng g⁻¹ for Au, Pt, Pd, Ir and Rh, respectively. The accuracy of the proposed method was tested by determining these elements in SARM 7 platinum-ore reference material. For all the analytes, the relative standard deviation of the combined dissolution, separation and determination methods was below 3.5% (n = 6).     

Influence of hydrogen gas over the interference of acids in inductively coupled plasma atomic emission spectrometry

The effect of hydrogen gas on the plasma and its influence on acid interferences in plasma atomic emission spectrometry was studied. The study was performed with HCl and HNO₃ in the concentration range of 0–2 mol l⁻¹. Vanadium and magnesium were used as test elements, the study was extended to other several elements. The effects of hydrogen gas on the plasma were studied by measuring excitation temperature, electron number density and the ionic-to-atomic line intensity ratio. The net effect of hydrogen was an increase in electron density and ionic to atomic line intensity ratio. A small increase in the excitation temperature was observed. The signal suppression for ionic lines causes by mineral acid was reduced when small amounts of hydrogen was introduced into the plasma as sheathing gas. This effect was attributed to the increase in plasma electron density.     

Determination of long-lived radionuclides in concrete matrix by laser ablation inductively coupled plasma mass spectrometry

A laser ablation system using a Nd:YAG laser was coupled both to a quadrupole inductively coupled plasma (ICP) mass spectrometer and to a double-focusing sector field ICP mass spectrometer. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was applied for the determination of long-lived radionuclides in a concrete matrix. The investigated samples were two laboratory standards with a concrete matrix, which we doped with different long-lived radionuclides (e.g. ⁹⁹Tc, ²³²Th, ²³³U, ²³⁷Np) from the ng g⁻¹ to μ g⁻¹ concentration range and an undoped concrete material (blank). Detection limits for long-lived radionuclides in the 10 ng g⁻¹ range are reached for LA-ICP-MS using the quadrupole mass spectrometer. With double-focusing sector field ICP-MS, the limits of detection are in general one order of magnitude lower and reach the sub ng g⁻¹ range for ²³³U and ²³⁷Np. A comparison of mass spectrometric results with those of neutron activation analysis on undoped concrete sample indicates that a semiquantitative determination of the concentrations of the minor and trace elements in the concrete matrix is possible with LA-ICP-MS without using a standard reference material.     

Nanometer-size titanium dioxide microcolumn on-line preconcentration of trace metals and their determination by inductively coupled plasma atomic emission spectrometry in water

A new method using a microcolumn packed with nanometer TiO₂ as solid-phase extractant has been developed for the simultaneous preconcentration of trace amounts of Cu, Mn, Cr and Ni prior to their measurements by inductively coupled plasma atomic emission spectrometry (ICP-AES). Effects of pH, sample flow rate and volume, elution solution and interfering ions on the recovery of the analytes have been investigated. The adsorption capacity of nanometer TiO₂ was found as 0.108, 0.149, 0.039 and 0.034 mmol g⁻¹ for Cu, Cr, Mn and Ni, respectively. The separation of analytes can be achieved from water samples with a concentration factor of 50 times. The method has been applied for the determination of trace elements in biological sample and lake water with satisfactory results.     

Analysis of yttrium aluminium borate crystals by solution-based methods: inductively coupled plasma atomic emission spectrometry and flame atomic absorption spectrometry

Comparative analysis of yttrium aluminium borate (YAB) /YAl₃(BO₃)₄/ optical single crystals was performed by flame atomic absorption spectrometry (FAAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES) methods for Cr, Dy, Er, Yb, Y, Al, B and Mo. The dopant element, Ce, could be determined only by the ICP-AES method at the required concentration level. The powdered crystal samples were fused with lithium metaborate (LiBO₂) at 950 °C in a platinum crucible and then dissolved in 6 mol l⁻¹ HCl. Although this fusion-dissolution procedure proved to be simple and effective, the quantitative determination of B—as the matrix element in samples—was handicapped by the B content of the fusing reagent. For the FAAS method, with the use of nitrous oxide–acetylene flame, cesium chloride ionization buffer and lanthanum chloride releasing agent [0.1+0.2% (m/v), respectively] were applied. These agents enhanced the atomic absorption signals of Cr, Dy, Er, Mo, Yb and Y, whereas no change of sensitivity was resulted in for Al and B. A fairly good agreement was found between the results of the two alternative spectrochemical methods. The predicted stoichiometry of the crystals was also well approximated indicating the reliability of the crystal growth technology applied.     

Multi-elemental analysis of non-food packaging materials by inductively coupled plasma-time of flight-mass spectrometry

Commercial non-food packaging materials of four different matrices (paper, low density polyethylene (LDPE), polyethylene-polypropylene (PE-PP) and high density polyethylene (HDPE)) were examined for the content of Cr, Ni, Cu, Zn, As, Mo, Cd, Sb, Ba, Hg, Tl, Pb and U. The examined samples (0.17–0.35 g) were digested in HNO₃ and H₂O₂ (papers, LDPE and PE-PP) and in HNO₃, H₂SO₄ and H₂O₂ (HDPE) using microwave assisted high pressure system. The inductively coupled plasma-time of flight-mass spectrometry (ICP-TOFMS) has been employed as the detection technique. All measurements were carried out using internal standardization. Yttrium and rhodium (50 ng g⁻¹) were used as internal standards. The detection and quantification limits obtained were in the range of 0.005 ng g⁻¹ (⁵²Cr) to 0.51 ng g⁻¹ (⁶⁶Zn) and 0.015 μg g⁻¹ (⁵²Cr) to 2.02 μg g⁻¹ (⁶⁶Zn) of dry mass, respectively. The evaluated contents (mg kg⁻¹) of particular elements in the examined materials were as follows: 0.22–219; <1.05–9.03; 1.25–112; <2.02–449; <0.98–<1.30; <0.36–2.06; <0.29–113; <0.22–44.1; <0.06–57.4; <0.66–<0.88; <0.08–0.24; <0.13–1222 and <0.08–0.44 for Cr, Ni, Cu, Zn, As, Mo, Cd, Sb, Ba, Hg, Tl, Pb and U, respectively.     

Determination of Cu, Mn, Ni and Sn in gasoline by electrothermal vaporization inductively coupled plasma mass spectrometry, and emulsion sample introduction

Trace metals in fuels, except in the case of additives, are usually undesirable and normally they occur in very low concentrations in gasoline, requiring sensitive techniques for their determination. Coupling of electrothermal vaporization with inductively coupled plasma mass spectrometry minimizes the problems related to the introduction of organic solvents into the plasma. Furthermore, sample preparation as oil-in-water emulsions reduces problems related to gasoline analysis. In this work, a method for determination of Cu, Mn, Ni and Sn in gasoline is proposed. Samples were prepared by forming a 10-fold diluted emulsion with a surfactant (Triton X-100), after treatment with concentrated HNO₃. The sample emulsion was pre-concentrated in the graphite tube by repeated pipetting and drying. External calibration was used with aqueous standards in a purified gasoline emulsion. Six samples from different gas stations were analyzed, and the analyte concentrations were found to be in the μg l⁻¹ range or below. The limits of detection were 0.22, 0.02, 0.38 and 0.03 μg l⁻¹ for Cu, Mn, Ni and Sn, respectively. The accuracy of the method was estimated using a recovery test.     

Analytical procedures for the determination of selected major (Al, Ca, Fe, K, Mg, Na, and Ti) and trace (Li, Mn, Sr, and Zn) elements in peat and plant samples using inductively coupled plasma-optical emission spectrometry

A simple, robust and reliable analytical procedure for the determination of Al, Ca, Fe, K, Li, Mg, Mn, Na, Sr, Ti, and Zn in peat and plant materials by inductively coupled plasma-optical emission spectrometry (ICP-OES) was developed. A microwave heated high pressure autoclave was used to digest powdered sample aliquots (approximately 200 mg) with different acid mixtures including nitric acid (HNO₃), tetrafluoroboric acid (HBF₄) and hydrogen peroxide (H₂O₂). The optimized acid mixture for digestion of plant and peat samples consisted of 3 mL HNO₃ and 0.1 mL HBF₄, in addition to H₂O₂ which was sub-boiled into the PTFE digestion tubes during heating of the autoclave. Using HNO₃ alone, recoveries of Al and Ti were too low by 40 and 160%, respectively, because HNO₃ could not fully liberate the analytes of interest from the silicate fraction of the plant and peat matrix. However, for all other elements (such as Mn, Sr, and Zn), the use of HBF₄ was less critical. The accuracy of the analytical procedure developed was evaluated with peat and plant reference materials of different origin and composition. The ICP-OES instrument was optimized using solutions of plant reference materials considering RF power, nebulizer pressure, auxiliary gas flow and rinse time. Scandium was used as an online internal standard (IS) as it provided accurate results and showed less than 3% drift in sensitivity over time which was lower compared to other potential IS such as Rh (20%) and In (6%). The combination of most sensitive and less sensitive wavelengths allowed to obtain low detection limits and highest possible dynamic range. The achieved procedure detection limits ranged from 0.05 μg g⁻¹ (Li) to 15 μg g⁻¹ (Ca) and allowed a precise quantification of all elements. Comparative X-ray fluorescence spectrometric measurements of solid peat and plant samples generally agreed well with results obtained by digestion/ICP-OES. To overcome interferences caused by Na, K, and Li, a solution of 10 μg g⁻¹ CsCl₂ was successfully used as an ionization buffer. The good agreement between the found and certified concentrations in plant and peat reference materials indicates that the developed analytical procedure is well suited for further studies on the fate of major elements in plant and peat matrices.     

Silicon determination by inductively coupled plasma atomic emission spectrometry after generation of volatile silicon tetrafluoride

A method for the determination of silicon by inductively coupled plasma atomic emission spectrometry (ICP-AES) is described. The procedure is based on a discontinuous generation of volatile silicon tetrafluoride in concentrated sulphuric acid medium after injecting 125 μl of 0.1%, w/v sodium fluoride solution into 100 μl of the sample. The gaseous silicon tetrafluoride is fed directly into the ICP torch by a flow of 250 ml min⁻¹ Ar carrier gas. The calibration curve was linear up to at least 100 μg ml⁻¹ of Si(IV) and the absolute detection limit was 9.8 ng working with a solution volume of 100 μl. The relative standard deviation for six measurements of 10 μg ml⁻¹ of Si(IV) was 2.32%. The method was applied to the determination of silicon in water and iron ores.     

Speciation of iodate and iodide in seawater by non-suppressed ion chromatography with inductively coupled plasma mass spectrometry

A non-suppressed ion chromatography (IC) with inductively coupled plasma mass spectrometry (ICP-MS) has been developed for simultaneous determination of trace iodate and iodide in seawater. An anion-exchange column (G3154A/101, provided by Agilent) was used for the separation of iodate and iodide with an eluent containing 20 mM NH₄NO₃ at pH 5.6, which reduced the build-up of salts on the sampler and skimmer cones. The influences of competing ion (NO₃⁻) in the eluent on the retention time and detection sensitivity were investigated to give reasonable resolution and detection limits. Linear plots were obtained in a concentration range of 5.0–500 μg/L and the detection limit was 1.5 μg/L for iodate and 2.0 μg/L for iodide. The proposed method was used to determinate iodate and iodide in seawaters without sample pre-treatment with exception of dilution.     

Investigation of equilibration and uncertainty contributions for the determination of inorganic mercury and methylmercury by isotope dilution inductively coupled plasma mass spectrometry

The mass fractions of Hg and methylmercury, in two certified reference materials, NIST2710 and DORM-2, have been determined by total and species-specific isotope dilution analysis (IDA), respectively, and uncertainty budgets for each analysis calculated. The mass fraction of Hg in NIST2710 was determined by ID using multicollector sector field inductively coupled plasma mass spectrometry (MC-SF-ICP-MS) whilst the mass fraction of methylmercury in DORM-2 was determined using HPLC coupled with quadrupole ICP-MS.

The extent of equilibration between the spike and the particulate bound mercury compounds was studied temporally by monitoring the ²⁰⁰Hg:¹⁹⁹Hg isotope amount ratio and by determining the total amount of Hg in the liquid phase. For the NIST2710 complete equilibration was only achieved when concentrated HNO₃ in combination with a microwave digestion was employed, and good agreement between the found (31.7±4.0 μg g⁻¹, expanded uncertainty k=2) and certified (32.6±1.8 μg g⁻¹) values was obtained. For DORM-2 complete equilibration of methylmercury between the liquid and solid phases was achieved when using 50:50 H₂O:CH₃OH (v/v) and 0.01% 2-mercaptoethanol as the solvent. Even though only 50% of the analyte was extracted into the liquid phase, complete equilibration was achieved, hence, the found methylmercury mass fraction (4.25±0.47 μg g⁻¹, expanded uncertainty k=2) was in good agreement with the certified value (4.47±0.32 μg g⁻¹).     

Capillary electrochromatographic separation of metal ion species with on-line detection by inductively coupled plasma mass spectrometry

A bonded phase capillary column containing macrocyclic polyamine, [28]ane-N₆O₂ functional groups was used for the electrophoretic separation of arsenic, chromium and selenium species. A simple device interfacing this capillary electrochromatography (CEC) systems to an inductively coupled plasma mass spectrometer (ICPMS) is described. The dimension of the capillary column was 160 cm×100 μm i.d. To accommodate this electrophoretic separation, an auxiliary capillary was used with nitric acid (0.05 M) as makeup liquid. With the electrokinetic method at –20 kV, 20 s and a nebulizer gas flow rate of 1 l min⁻¹, the sample injected was analyzed with an applied potential of −20 kV. The background electrolyte buffer for the separation of CrO₄²⁻–Cr³⁺ was phosphate (20 mM, pH 6.5). That for HAsO₄²⁻–Ph₄As⁺ was pyromellitate (20 mM, pH 6.0) and for SeO₄²⁻–SeO₃²⁻ was acetate (20 mM, pH 6.0). The role of the buffer’s anion was also discussed. The separation efficiency of the bonded phase was compared with the bare fused silica. Concentration detection limits for these metal ions were in the low ppb range. In addition, the matrix effect of the established system with the bonded phase was found smaller than that with the bare fused silica.     

Method development for the determination of manganese, cobalt and copper in green coffee comparing direct solid sampling electrothermal atomic absorption spectrometry and inductively coupled plasma optical emission spectrometry

A method has been developed for the determination of cobalt, copper and manganese in green coffee using direct solid sampling electrothermal atomic absorption spectrometry (SS-ET AAS). The motivation for the study was that only a few elements might be suitable to determine the origin of green coffee so that the multi-element techniques usually applied for this purpose might not be necessary. The three elements have been chosen as test elements as they were found to be significant in previous investigations. A number of botanical certified reference materials (CRM) and pre-analyzed samples of green coffee have been used for method validation, and inductively coupled plasma optical emission spectrometry (ICP OES) after microwave-assisted acid digestion of the samples as reference method. Calibration against aqueous standards could be used for the determination of Mn and Co by SS-ET AAS, but calibration against solid CRM was necessary for the determination of Cu. No significant difference was found between the results obtained with the proposed method and certified or independently determined values. The limits of detection for Mn, Cu and Co were 0.012, 0.006 and 0.004 μg g⁻¹ using SS-ET AAS and 0.015, 0.13 and 0.10 μg g⁻¹ using ICP OES. Seven samples of Brazilian green coffee have been analyzed, and there was no significant difference between the values obtained with SS-ET AAS and ICP OES for Mn and Cu. ICP OES could not be used as a reference method for Co, as essentially all values were below the limit of quantification of this technique.     

-电感耦合等离子体质谱法测定硅锰冶炼渣中8种金属元素

实验采用HCl-HNO₃-HF-HClO₄混合酸为消解体系对样品进行前处理,加入1.0 mL盐酸羟胺溶液(100 g/L)溶解残渣,选择合适的同位素,以¹⁰³Rh为内标测定Cr、Co、Ni、Cu、Zn和Cd,以¹⁹³Ir为内标测定Tl和Pb,建立了电感耦合等离子体质谱(ICP-MS)法测定硅锰冶炼渣中8种重金属元素的方法。实验发现,样品前处理选择HCl∶HNO₃∶HF∶HClO₄=5∶5∶5∶1,并在复溶阶段加入1.0 mL盐酸羟胺溶液(100 g/L)可以完全消解样品,实验采用KED模式和干扰系数校正法消除质谱干扰,样品中待测元素的测定结果不受基体成分的干扰。通过绘制校准曲线及测定流程空白,各元素校准曲线的相关系数均大于0.9999,方法检出限为0.006~0.19 mg/kg,方法定量限为0.018~0.57 mg/kg。对硅锰渣实际样品进行测定,各元素的相对标准偏差(RSD,n=11)在0.83%~4.1%,加标回收率为94.7%~106%;经过人员比对实验,相对偏差为-4.54%~4.24%。测定结果稳定可靠,能满足硅锰冶炼渣中8种微量金属元素含量的分析检测要求。     

High-Resolution continuum-source atomic absorption spectrometry in an inductively coupled plasma with photodiode array detection

Atomic absorption spectrometry (AAS) is a well established technique using flames and graphite furnaces. An inductively coupled plasma (ICP), however, is an attractive alternative atom/ion reservoir. A high-resolution continuum-source atomic absorption spectrometer with a photodiode array detector and an ICP as the atomization/ionization reservoir is described. Multi-wavelength capability permits the simultaneous determination of several elements by their atomic and/or ionic transitions. Each acquired spectrum is averaged for 10 s to improve the signal-to-noise ratios. Detection limits are calculated for 14 elements and compared with literature values.     

Comparative study of the instrumental couplings of high performance liquid chromatography with microwave-assisted digestion hydride generation atomic fluorescence spectrometry and inductively coupled plasma mass spectrometry for chiral speciation of selenomethionine in breast and formula milk

A comparison of chiral separation and analysis of selenomethionine in breast and formula milk, using high performance liquid chromatography (HPLC) on a glycopeptide teicoplanin-based chiral stationary phase (Chirobiotic T), coupled to atomic fluorescence spectrometry (AFS) and inductively coupled plasma (ICP) MS detectors has been performed. The coupling HPLC-microwave-assisted digestion hydride generation requires on-line post-column analytes treatment, and a severe sample clean-up for fat and proteins elimination using centrifugation and ultrafiltration. Underivatized -selenomethionine enantiomers were completely resolved in 10 min using unbuffered water mobile phase at 1 ml min⁻¹ flow. Good selectivity and sensitivities (detection limits 3.1 and 3.5 ng ml⁻¹ as Se for - and -selenomethionine, respectively) were obtained, and method robustness and simplicity, together to the low cost of AFS detector, makes it suitable for infant milk routine analysis. HPLC–ICP-MS coupling exhibits very low detection limits (0.9 ng ml⁻¹, as Se) for each -selenomethionine enantiomers, but the method suffers from matrix influence, that produces a poor S/N ratio and low reliability.

The methods were applied to breast and formula milk samples with recoveries of 80% of the total selenium presence, which is attributable to the existence of other unknown species. -Selenomethionine was the only isomer present in breast milk, but a 30% of -selenomethionine was also detected in formula milk.     

Determination of arsenic in gold by flow injection inductively coupled plasma mass spectrometry with matrix removal by reductive precipitation

Arsenic was determined in gold by flow injection hydride generation inductively coupled plasma-mass spectrometry following a batch mode reductive precipitation removal of the interfering gold matrix. A solution of potassium iodide, L-ascorbic acid, and hydrochloric acid was used as the reluctant. The recovery of gold by precipitation and filtration was 99 ± 3%. The detection limit for arsenic in gold was 55 ng g⁻¹ in the solid. The concentration of arsenic that was determined in the Royal Canadian Mint gold sample FAU-10 was 29.7 μg g⁻¹ in the solid; this value was indistinguishable, with 95% confidence, from values determined at the Royal Canadian Mint by graphite furnace atomic absorption spectrometry and by inductively coupled plasma-mass spectrometry. The standard deviation for four replicate determinations of the arsenic in FAU-10 was 0.972 μg g⁻¹ in the solid.     

Determination of lead in seawater by inductively coupled plasma optical emission spectrometry after separation and pre-concentration with cocrystallized naphthalene alizarin

An analytical method for separation and pre-concentration of lead in seawater for determination by inductively coupled plasma optical emission spectrometry has been investigated. Lead was retained in the solid phase (0.5 g) composed of co-precipitated naphthalene and alizarin red. The solid phase quantitatively sorbs Pb(II) at pH 8–9, and the metal was eluted using 5.0 ml of 2 mol l⁻¹ nitric acid. The effect of NaCl, KCl, BaCl₂, CaCl₂, Na₂SO₄, MgCl₂ and Na₃PO₄ on the sorption of Pb(II) in the solid phase was studied. A set of solutions containing varying amounts of electrolytes (0.5; 1.0; 3.0 and 5.0% m/v) with Pb (50 μg) was prepared and the recommended procedure applied. The Na₃PO₄ was found to interfere; the other electrolytes did not interfere up to 5% m/v. A pre-concentration factor of 40 was obtained in this analytical procedure. The limit of detection and limit of quantification for Pb(II) were 53 and 176 μg l⁻¹, respectively. Lead was determined in seawater samples collected in Salvador city, Bahia, Brazil. The precision, expressed as R.S.D., was 1.8–4.6%, and the recovery of lead added to seawater samples was 95–97%.     

High efficiency nebulization for helium inductively coupled plasma mass spectrometry

A pneumatically-driven, high efficiency nebulizer is explored for helium inductively coupled plasma mass spectrometry. The aerosol characteristics and analyte transport efficiencies of the high efficiency nebulizer for nebulization with helium are measured and compared to the results obtained with argon. Analytical performance indices of the helium inductively coupled plasma mass spectrometry are evaluated in terms of detection limits and precision. The helium inductively coupled plasma mass spectrometry detection limits obtained with the high efficiency nebulizer at 200 μL/min are higher than those achieved with the ultrasonic nebulizer consuming 2 mL/min solution, however, precision is generally better with high efficiency nebulizer (1–4% vs. 3–8% with ultrasonic nebulizer). Detection limits with the high efficiency nebulizer at 200 μL/min solution uptake rate approach those using ultrasonic nebulizer upon efficient desolvation with a heated spray chamber followed by a Peltier-cooled multipass condenser.     

Spectral interferences in the determination of traces of scandium, yttrium and rare earth elements in “pure” rare earth matrices by inductively coupled plasma atomic emission spectrometry: Part VII — Terbium, Dysprosium, Holmium and Thulium

This article is the seventh part of a series of papers discussing the spectral interferences of rare earth elements (REEs) in ICP-AES. Radial viewing 27.12 MHz inductively coupled plasma atomic emission spectrometry (ICP-AES) was used in the determination of scandium, yttrium and rare earth elements in Tb₂O₃, Dy₂O₃, Ho₂O₃ and Tm₂O₃ as “pure” rare earth matrices. The quantification of the interferences in terms of Q-values for line interference Q_I(_a) and wing background interference Q_W(Δλ_a) were used in accordance with Boumans and Vrakking [Spectrochim. Acta Part B 43 (1988) 69]. The “best” analysis lines from point of view of spectral interferences were selected. The true detection limits by using the “best” analysis lines were calculated.