银/金纳米线阵列表面增强拉曼基底的制备及对孔雀石绿的高灵敏度检测

利用种子介导的软模板生长方法制备了金纳米线(Au NWs)阵列, 通过调节生长温度控制Au NWs阵列的形貌, 最后在经硼氢化钠(NaBH₄)清洗过的Au NWs阵列上化学沉积银纳米颗粒(Ag NPs), 制得银/金纳米线(Ag/Au NWs)阵列作为表面增强拉曼散射(SERS)基底. 选用罗丹明6G(R6G)作为拉曼探针分子测定了Ag/Au NWs阵列的SERS性能. 结果表明, Ag/Au NWs阵列作为SERS基底具有高灵敏度、 优异的信号均匀性和良好的稳定性. 使用Ag/Au NWs阵列对孔雀石绿(MG)检测的检出限可低至1×10^-8 mol/L, 线性范围为 1×10^-8~1×10^-4 mol/L. NaBH₄可以在不影响SERS性能的情况下去除Ag/Au NWs阵列上吸附的分子, 使得 SERS基底可以重复使用. 使用Ag/Au NWs阵列对湖水中的MG进行检测, 得到了可靠的回收率, 证明Ag/Au NWs 阵列在检测环境水体中的孔雀石绿上具有应用潜力.     

Facile Fabrication of Multi‐targeted and Stable Biochemical SERS Sensors

The direct transfer of single‐crystalline Au nanowires (NWs) onto Au substrates was achieved by a simple attachment and detachment process. In the presence of a lubricant, Au NWs grown vertically on a sapphire substrate were efficiently moved to an Au substrate through van der Waals interactions. We demonstrate that the transferred Au NWs on the Au substrate can act as sensitive, reproducible, and long‐term‐stable surface‐enhanced Raman scattering (SERS) sensors by detecting human α‐thrombin as well as Pb²⁺ and Hg²⁺ ions. These three biochemically and/or environmentally important analytes were successfully detected with high sensitivity and selectivity by Au NW‐SERS sensors bound by a thrombin‐binding aptamer. Furthermore, the as‐prepared sensors remained in working order after being stored under ambient conditions at room temperature for 80 days. Because Au NWs can be routinely transferred onto Au substrates and because the resultant Au NW‐SERS sensors are highly stable and provide with high sensitivity and reproducibility of detection, these sensors hold potential for practical use in biochemical sensing.     

Preparation of gold-tellurium hybrid nanomaterials for surface-enhanced Raman spectroscopy

We report a simple method for preparing three different SERS-active substrates. Concentrated hydrazine solution as the reducing agent and tellurium dioxide as the precursor were used to prepare Te nanowires (NWs). The as-prepared Te NWs have an average length of 547.7 +/- 111.6 nm and an average width of 15.1 +/- 2.7 nm. Through the reaction of Te NWs with sodium tetrachloroaurate in the presence of hexadecyltrimethylammonium bromide (CTAB) over reaction times of 10, 20, and 60 min, gold-tellurium nanodumbbells, gold-tellurium nanopeapods, and gold pearl-necklace nanomaterials (Au PNNs) were obtained, respectively. By controlling the reaction time, the distance between adjacent gold nanoparticles (Au NPs) in each Te nanowire was tunable, allowing us to investigate its effect on the SERS signals. Having shorter distances among Au NPs (greater electromagnetic fields), the Au PNNs provided a reproducible enhancement factor of 5.6 x 10(9).     

Au Nanowire–Au Nanoparticles Conjugated System which Provides Micrometer Size Molecular Sensors

We report a new type of molecular sensor using a Au nanowire (NW)–Au nanoparticles (NPs) conjugated system. The Au NW–NPs structure is fabricated by the self‐assembly of biotinylated Au NPs on a biotinylated Au NW through avidin; this creates hot spots between NW and NPs that strongly enhance the Raman signal. The number of the Au NPs attached to the NW is reproducibly proportional to the concentration of the avidin, and is also proportional to the measured surface‐enhanced Raman scattering (SERS) signals. Since this well‐defined NW–NPs conjugated sensor is only a few micrometer long, we expect that development of multiplex nanobiosensor of a few tens micrometer size would become feasible by combining individually modified multiple Au NWs together on one substrate.     

Synthesis and alignment of silver nanorods and nanowires and the formation of Pt, Pd, and core/shell structures by galvanic exchange directly on surfaces

Here we describe the synthesis of Ag nanorods (NRs) (aspect ratio <20) and nanowires (NWs) (aspect ratio > or =20) directly on surfaces by seed-mediated growth. The procedure involves attaching gold seed nanoparticles (Au NPs) to 3-mercaptopropyltrimethoxysilane (MPTMS)-functionalized silicon or glass surfaces and growing them into NRs/NWs by placing the substrates into a solution containing cetyltrimethylammonium bromide (CTAB), silver nitrate, and ascorbic acid with the pH ranging from 7 to 12. Under our conditions, Ag NRs/NWs grow optimally at pH 10.6 with a 3% yield, where spherical, triangular, and hexagonal nanostructures represent the other byproducts. The length of Ag NRs/NWs ranges from 50 nm to more than 10 microm, the aspect ratio (AR) ranges from 1.4 to >300, and the average diameter is approximately 35 nm. Approximately 40% of the 1D structures are NRs, and 60% are NWs as defined by their ARs. We also report the alignment of Ag NRs/NWs directly on surfaces by growing the structures on amine-functionalized Si(100) surfaces after an amidation reaction with acetic acid and a method to improve the percentage of Ag NRs/NWs on the surface by removing structures of other shapes with adhesive tape. Surface-grown Ag NRs/NWs also react with salts of palladium, platinum, and gold via galvanic exchange reactions to form high-surface-area 1D structures of the corresponding metal. The combination of the seed-mediated growth of Ag on Au NRs followed by the galvanic exchange of Ag with Pd leads to interesting core/shell NRs grown directly on surfaces. We used scanning electron microscopy, UV-vis spectroscopy, and X-ray photoelectron spectroscopy to characterize the surface-grown nanostructures.     

Synthesis of single crystal Sn-doped In(2)O(3) nanowires: size-dependent conductive characteristics

Single crystalline Sn doped In(2)O(3) (ITO) NWs (nanowires) were synthesized via an Au-catalyzed VLS (vapor-liquid-solid) method at 600 °C. The different sizes (～20, ～40, ～80 nm) of the Au NPs (nanoparticles) provided the controllable diameters for ITO NWs during growth. Phase and microstructures confirmed by high-resolution transmission electron microscope images (HRTEM) and X-ray diffraction (XRD) spectra indicated that the phase of In(2)O(3) NWs had a growth direction of [100]. X-ray photoelectron spectroscopy (XPS) was employed to obtain the chemical compositions of the ITO NWs as well as the ratio of Sn/In and oxygen concentrations. The findings indicated that low resistivity was found for ITO NWs with smaller diameters due to higher concentrations of oxygen vacancies and less incorporation of Sn atoms inside the NWs. The resistivity of NWs increases with increasing diameter due to more Sn atoms being incorporated into the NW and their reduction of the amount of oxygen vacancies. Low resistivity NWs could be achieved again due to excess Sn atoms doped into the large diameter NWs. Therefore, by optimizing the well-controlled growth of the NW diameter and interface states, we are able to tune the electrical properties of Sn-doped ITO NWs.     

Unexpected optical response of single ZnO nanowires probed using controllable electrical contacts

Relying on combined electron-beam lithography and lift-off methods Au/Ti bilayer electrical contacts were attached to individual ZnO nanowires (NWs) that were grown by a vapor phase deposition method. Reliable Schottky-type as well as ohmic contacts were obtained depending on whether or not an ion milling process was used. The response of the ZnO NWs to ultraviolet light was found to be sensitive to the type of contacts. The intrinsic electronic properties of the ZnO NWs were studied in a field-effect transistor configuration. The transfer characteristics, including gate threshold voltage, hysteresis and operational mode, were demonstrated to unexpectedly respond to visible light. The origin of this effect could be accounted for by the presence of point defects in the ZnO NWs.     

Three-dimensional electrically interconnected nanowire networks formed by diffusion bonding

We demonstrate a new strategy to bond nanowires (NWs) using diffusion bonding of gold (Au). The strategy was used to form very large scale, electrically interconnected 3D NW networks composed of both homogeneous and heterogeneous (multisegmented) NWs. The size of the networks ranged from tens of micrometers to millimeters. We have measured the electrical characteristics of the networks and explored one application of the networks in 3D spatial chemical sensing.     

Au nanowire-on-film SERRS sensor for ultrasensitive Hg2+ detection

We report an ultrasensitive and selective single nanowire-on-film (SNOF) surface-enhanced resonance Raman scattering (SERRS) sensor for Hg(2+) detection based on structure-switching double stranded DNAs (dsDNAs). Binding of Hg(2+) induces conformational changes of the dsDNAs and let a Raman reporter get close to the SNOF structure, thereby turning on SERRS signal. The well-defined SNOF structure provides a detection limit of 100 pM with improved accuracy in Hg(2+) detection. This sensor is stable over a considerable amount of time and reusable after simple treatment. Since this SNOF sensor is composed of a single Au NW on a film, development of a multiplex sensor would be possible by employing NWs modified by multiple kinds of aptamers.     

Plasmon-enhanced photocatalytic properties of cu(2)o nanowire-au nanoparticle assemblies

Cu(2)O-Au nanocomposites (NCs) with tunable coverage of Au were prepared by a facile method of mixing gold nanoparticles (Au NPs) with copper(I) oxide nanowires (Cu(2)O NWs) in various ratios. These Cu(2)O-Au NCs display tunable optical properties, and their photocatalytic properties were dependent on the coverage density of Au NPs. The photocatalytic activity of Cu(2)O-Au NCs was examined by photodegradation of methylene blue. The presence of Au NPs enhanced the photodegradation efficiency of Cu(2)O NCs. The photocatalytic efficiency of Cu(2)O-Au NCs initially increased with the increasing coverage density of Au NPs and then decreased as the surface of Cu(2)O became densely covered by Au NPs. The enhanced photocatalytic efficiency was ascribed to enhanced light absorption (by the surface plasmon resonance) and the electron sink effect of the Au NPs.     

Unidirectional Pt silicide nanowires grown on vicinal Si(100)

We investigated the structure and electronic properties of unidirectional Pt(2)Si nanowires (NWs) grown on a Si(100)-2 degrees off surface. We found that Pt(2)Si NWs were formed along the step edges of the Si(100)-2 degrees off surface with c(4x6) reconstructions that occurred on the terraces of Si(100) using scanning tunneling microscopy and the structure of formed NWs was found to be Pt(2)Si by core-level photoemission spectroscopy. Moreover, we confirmed that the electronic band structures of the NWs along the NW direction are different from those perpendicular to the NWs and the surface state induced by the Pt(2)Si NWs was observed with a small density of state using the angle-resolved photoemission spectra.     

Single-step multiplex detection of toxic metal ions by Au nanowires-on-chip sensor using reporter elimination

We have developed a Au nanowires (NWs)-on-chip surface-enhanced Raman scattering (SERS) multiplex sensor that can sensitively detect multiple toxic metal ions. Most importantly, the reporter elimination method simplified the detection procedure to a single step, which has been much desired for remote environmental monitoring. This sensor has several notable features. First, it shows high reproducibility based on well-defined single-crystalline Au NWs. Second, single-NW-sensors that can detect a specific metal ion are combined for multiplex sensing of metal ions. Third, when a sample solution is put onto the NWs-on-chip sensor, a decrease in the SERS signal of a specific NW-sensor identifies the target metal ion. Simple, rapid, sensitive and quantitative detection of metal ions becomes possible through the measurement of the SERS signals. We successfully detected ions of mercury (Hg(2+)), silver (Ag(+)), and lead (Pb(2+)) coexisting in the same solution by using this sensor.     

Facile Synthesis Of Composition‐Controllable PtPdAuTe Nanowires As Superior Electrocatalysts For Direct Methanol Fuel Cells

Multicomponent Pt‐based nanowires (NWs) have attracted widespread attention as eletrocatalysts toward direct alcohol fuel cells because of their unique one‐dimensional structure and high reaction dynamics. Quaternary PtPdAuTe NWs are designed via a facile template method, and NWs with a different composition are obtained by adjusting the feed ratio of metal precursors. The direct displacement reaction of metal precursors with Te NWs and the partial oxidation of Te lead to the formation of quaternary NWs. The rough surface and abundant reactive sites deriving from the rearrangement of metal atoms on the Te NWs surface endow the PtPdAuTe NWs with a superior electrocatalytic property and durability for methanol oxidation. The Pt₂₀Pd₂₀Au₁₀Te₅₀ NWs display the largest mass activity and best stability among all catalysts. The preparation of PtPdAuTe NWs could provide a viable strategy for the preparation of other multicomponent NWs.     

Germanium telluride nanowires and nanohelices with memory-switching behavior

We report the synthesis of single-crystalline GeTe nanowires (NWs) and nanohelices (NHs) using a vapor transport method assisted by metal catalysts. The NWs have typical diameters of 65 +/- 20 nm and lengths reaching up to 50 mum, while NHs have an average helix diameter of 135 +/- 30 nm, with widely varying pitches. Electron microscopy and diffraction measurements show that these NWs and NHs are single crystalline and exhibit a rhombohedral structure. The devices incorporating individual GeTe NWs exhibit nonvolatile resistance changes associated with voltage-driven crystalline-amorphous transitions, suggesting that these NWs can be the basis of an electrically driven nonvolatile memory.     

Chiral transformation: from single nanowire to double helix

We report a new type of water-soluble ultrathin Au-Ag alloy nanowire (NW), which exhibits unprecedented behavior in a colloidal solution. Upon growth of a thin metal (Pd, Pt, or Au) layer, the NW winds around itself to give a metallic double helix. We propose that the winding originates from the chirality within the as-synthesized Au-Ag NWs, which were induced to untwist upon metal deposition.     

Composited hybrid electrocatalysts of Pt-based nanoparticles and nanowires for low temperature polymer electrolyte fuel cells

A new and highly improved electrocatalytic system of a composited hybrid electrode with Pt-based nanoparticles (NPs) and nanowires (NWs) is reported for low temperature polymer electrolyte fuel cells. Pt-based NWs have been realized as an option that can provide facile charge transport with a high activity for oxidation of fuels, for overcoming the disadvantages of Pt-based NPs as the state-of-the-art electrocatalysts. Moreover, a network-like electrode structure using the anisotropic morphology of Pt-based NWs can also supply efficient mass transport and mitigate uneconomical use of Pt by reducing embedded catalyst particles. Herein, we demonstrate that an advanced and very efficient hybrid structure of electrode, composited with highly-dispersed Pt-based NPs and NWs, shows significantly improved performances both in the CH₃OH-fueled and H₂-fueled fuel cells via synergistic effects by integrating advantages of two different morphologies.     

A single-source precursor route to unusual PbSe nanostructures by a solution-liquid-solid method

PbSe nanowires (NWs) have been synthesized by using a single-source precursor route. Carefully controlling the conditions of individual reactions leads to PbSe NWs with well-defined diameters (8-25 nm) and lengths (100 nm-1 μm). The as-grown PbSe NWs are highly crystalline, defect free, and readily dispersible in organic solvents. The NWs have been characterized by X-ray diffraction and high-resolution transmission electron microscopy.     

Preparation of Ag Nanowire @ Au Nanoparticle Hybrid Nanowires and their Influence on the Fluorescence Properties of P3HT

In this study, the galvanic displacement reaction between silver and AuCl₄⁻ was carried out to synthesize a series of silver nanowire (Ag NW) @ gold nanoparticle (Au NP) hybrid nanowires. The influence of Ag NW @ Au NP hybrid nanowires on the fluorescence properties of the poly (3‐hexylthiophene) (P3HT) was investigated. The particle sizes of Au NPs on the hybrid nanowires could be adjusted by varying the reaction time and the concentration of the HAuCl₄ solution. Furthermore, steady‐state fluorescence measurements showed that the fluorescence intensity of the P3HT films was higher on various Ag NW @ Au NP hybrid nanowires compared to that on a bare silicon substrate. This was due to the increase in the intensity of electromagnetic field by the localized surface plasmon resonances of Au NPs and surface plasmon polaritons of Ag NWs from the hybrid nanowires. The results were further confirmed by the Raman spectra of the P3HT films on different substrates.     

Effect of silver nanowires on the surface-enhanced Raman spectra (SERS) of the RNA bases

RNA bases have a great importance in the biological and genetics applications. The surface-enhanced Raman scattering (SERS) was used to study the orientation and adsorption structure of RNA bases adsorbed on the surface of silver nanowires (Ag NWs). The Ag NWs were prepared and its UV-vis spectra were recorded. The RNA bases oriented perpendicularly on the surface of Ag NWs, as the coverage area decreases. Consequently, the in-plane bands were enhanced according to the SERS selection rule. Many bands were red shifted due to the chemisorption of RNA bases on the Ag NWs surface. New bands corresponding to the base-surface bond were appeared in the SERS spectra.     

Enhanced growth of crystalline-amorphous core-shell silicon nanowires by catalytic thermal CVD using in situ generated tin catalyst

In this work,we prepared silicon nanowires(Si NWs) on both fluorine-doped SnO 2(FTO) coated glass substrate and common glass substrate by catalytic thermal chemical vapor deposition(CVD) using indium film as the catalyst.It is confirmed that indium can catalyze the growth of Si NWs.More importantly,we found that tin generated in situ from the reduction of SnO 2 by indium can act as catalyst,which greatly enhances the growth of Si NWs on FTO substrate.The obtained Si NWs have a uniform crystalline-amorphous core-shell structure that is formed via vapor-liquid-solid and vapor-solid growth of silicon sequentially.This work provides a strategy to prepare Si NWs in high yield by catalytic thermal CVD using the low melting point metal catalysts.