Effect of capillary condensation on friction force and adhesion

Friction force measurements have been conducted with a colloid probe on mica and silica (both hydrophilic and hydrophobized) after long (24 h) exposure to high-humidity air. Adhesion and friction measurements have also been performed on cellulose substrates. The long exposure to high humidity led to a large hysteresis between loading and unloading in the friction measurements with separation occurring at large negative applied loads. The large hysteresis in the friction-load relationship is attributed to a contact area hysteresis of the capillary condensate which built up during loading and did not evaporate during the unloading regime. The magnitude of the friction force varied dramatically between substrates and was lowest on the mica substrate and highest on the hydrophilic silica substrate, with the hydrophobized silica and cellulose being intermediate. The adhesion due to capillary forces on cellulose was small compared to that on the other substrates, due to the greater roughness of these surfaces.     

A modeling approach to describe the adhesion of rough, asymmetric particles to surfaces

A combined theoretical and experimental study of the adhesion of alumina particles and polystyrene latex spheres to silicon dioxide surfaces was performed. A boundary element technique was used to model electrostatic interactions between micron-scale particles and planar surfaces when the particles and surfaces were in contact. This method allows quantitative evaluation of the effects of particle geometry and surface roughness on the electrostatic interaction. The electrostatic interactions are combined with a previously developed model for van der Waals forces in particle adhesion. The combined model accounts for the effects of particle and substrate geometry, surface roughness and asperity deformation on the adhesion force. Predictions from the combined model are compared with experimental measurements made with an atomic force microscope. Measurements are made in aqueous solutions of varying ionic strength and solution pH. While van der Waals forces are generally dominant when particles are in contact with surfaces, results obtained here indicate that electrostatic interactions contribute to the overall adhesion force in certain cases. Specifically, alumina particles with complex geometries were found to adhere to surfaces due to both electrostatic and van der Waals interactions, while polystyrene latex spheres were not affected by electrostatic forces when in contact with various surfaces.     

Experimental humidity dependency of small particle adhesion on silica and titania

The humidity present in ambient atmosphere affects the adhesion of small particles by causing capillary bridge formation between the particle and the surface. Even in moderate relative humidities this, usually attractive, force can have a significant effect on adhesion behaviour of micro and sub-micro particles. We have directly measured the pull-off forces of initially adhered oxide particles on oxide surfaces with atomic force microscope in controlled atmosphere with adjustable humidity. We demonstrate the effect of the surface roughness resulting in two different regions of capillary formation and the particle shape having a strong effect on the humidity dependency of adhesion. The experimental results are explained by theoretical framework.     

Effects of adsorbed water layer structure on adhesion force of silicon oxide nanoasperity contact in humid ambient

The origin of the large relative-humidity (RH) dependence of the adhesion force in the single-asperity contact between silicon oxide surfaces is elucidated. As RH increases, the adhesion force measured with an atomic force microscopy (AFM) initially increases, reaches a maximum, and then decreases at high RH. The capillary force alone cannot explain the observed magnitude of the RH dependence. The origin of the large RH dependence is due to the presence of an icelike structured water adsorbed at the silicon oxide surface at room temperature. A solid-adsorbate-solid model is developed calculating the contributions from capillary forces, van der Waals interactions, and the rupture of an ice-ice bridge at the center of the contact region. This model illustrates how the structure, thickness, and viscoelastic behavior of the adsorbed water layer influence the adhesion force of the silicon oxide nanoasperity contact.     

Stick slip contact mechanics between dissimilar materials: effect of charging and large friction

Measurements of the contact radius as a function of applied force between a mica surface and a silica surface (mica/silica) in air are reported. The load/unload results show that the contact radius generally increases with applied force. Because of the presence of charging due to contact electrification, both a short-range van der Waals adhesion force and longer-range electrostatic adhesive interaction contribute to the measured force. The results indicate that approximately 20% of the pull-off force is due to van der Waals forces. The contact radius versus applied force results can be fit to Johnson-Kendall-Roberts (JKR) theory by considering that only the short-range van der Waals forces contribute to the work of adhesion and subtracting a constant longer-range electrostatic force. Also, an additional and unexpected step function is superimposed on the contact radius versus applied force curve. Thus, the contact diameter increases in a stepped dependence with increasing force. The stepped contact behavior is seen only for increasing force and is not observed when symmetric mica/mica or silica/silica contacts are measured. In humid conditions, the contact diameter of the mica/silica contact increases monotonically with applied force. Friction forces between the surfaces are also measured and the shear stress of a mica/silica interface is 100 times greater than the shear stress of a mica/mica interface. This large shear stress retards the increase in contact area as the force is increased and leads to the observed stepped contact mechanics behavior.     

Adhesion forces between wetted solid surfaces

We investigate in this paper the influence of wetting films on the adhesion forces between macroscopic solid surfaces connected by a liquid bridge. We show that the capillary forces are dependent on the interactions governing the wetting layers, and that those interactions may be determined from the measurement of the capillary force in the presence of a condensable vapor. We illustrate those results with a surface force apparatus experiment where the capillary force between high-energy surfaces is measured for different liquid pressures.     

Correlations between adhesion hysteresis and friction at molecular scales

Correlations between adhesion hysteresis and local friction are theoretically and experimentally investigated. The model is based on the classical theory of adhesional friction, contact mechanics, capillary hysteresis, and nanoscale roughness. Adhesion hysteresis was found to scale with friction through the scaling factor containing a varying ratio of adhesion energy over the reduced Young's modulus. Capillary forces can offset the relationship between adhesion hysteresis and friction. Measurements on a wide range of engineering samples with varying adhesive and elastic properties confirm the model. Adhesion hysteresis is investigated under controlled, low humidity atmosphere via ultrasonic force microscopy. Friction is measured by the friction force microscopy.     

Colloidal forces between bitumen surfaces in aqueous solutions measured with atomic force microscope

Colloidal forces between bitumen surfaces in aqueous solutions were measured with an atomic force microscope (AFM). The results showed a significant impact of solution pH, salinity, calcium and montmorillonite clay addition on both long-range (non-contact) and adhesion (pull-off) forces. Weaker long-range repulsive forces were observed under conditions of lower solution pH, higher salinity and higher calcium concentration. Lower solution pH, salinity and calcium concentration resulted in a stronger adhesion forces. The addition of montmorillonite clays increased long-range repulsive forces and decreased adhesion forces, particularly when co-added with calcium ions. The measured force profiles were fitted with extended DLVO theory to show the repulsive electrostatic double layer and attractive hydrophobic forces being the dominant components in the long-range forces between the bitumen surfaces. At a very short separation distance (less than 4–6 nm), a strong repulsion of steric origin was observed. The findings provide a fundamental understanding of bitumen emulsion stability and a mechanism of bitumen “aeration” in bitumen recovery processes from oil sands.     

Residence time, loading force, pH, and ionic strength affect adhesion forces between colloids and biopolymer-coated surfaces

Exopolymers are thought to influence bacterial adhesion to surfaces, but the time-dependent nature of molecular-scale interactions of biopolymers with a surface are poorly understood. In this study, the adhesion forces between two proteins and a polysaccharide [Bovine serum albumin (BSA), lysozyme, or dextran] and colloids (uncoated or BSA-coated carboxylated latex microspheres) were analyzed using colloid probe atomic force microscopy (AFM). Increasing the residence time of an uncoated or BSA-coated microsphere on a surface consistently increased the adhesion force measured during retraction of the colloid from the surface, demonstrating the important contribution of polymer rearrangement to increased adhesion force. Increasing the force applied on the colloid (loading force) also increased the adhesion force. For example, at a lower loading force of approximately 0.6 nN there was little adhesion (less than -0.47 nN) measured between a microsphere and the BSA surface for an exposure time up to 10 s. Increasing the loading force to 5.4 nN increased the adhesion force to -4.1 nN for an uncoated microsphere to a BSA surface and to as much as -7.5 nN for a BSA-coated microsphere to a BSA-coated glass surface for a residence time of 10 s. Adhesion forces between colloids and biopolymer surfaces decreased inversely with pH over a pH range of 4.5-10.6, suggesting that hydrogen bonding and a reduction of electrostatic repulsion were dominant mechanisms of adhesion in lower pH solutions. Larger adhesion forces were observed at low (1 mM) versus high ionic strength (100 mM), consistent with previous AFM findings. These results show the importance of polymers for colloid adhesion to surfaces by demonstrating that adhesion forces increase with applied force and detention time, and that changes in the adhesion forces reflect changes in solution chemistry.     

Effect of contact angle hysteresis on the measurement of capillary forces

We conduct experimental investigations of macroscopic capillary forces between two flat rigid substrates characterized by their advancing and receding contact angles with water. Our results exhibit excellent agreement with theoretical predictions obtained by the numerical solution of the capillary equation. On the basis of this comparison, we use the measurements of the capillary force to investigate the phenomenon of contact angle hysteresis. We present examples of force measurements for surfaces that display low, moderate, and high contact angle hysteresis and compare results for a larger variety of substrates. Finally, we show that for the case of water, the role of viscosity is insignificant within the range of force and velocity measured in the present work.     

The Effect of a Cationic Polyelectrolyte on the Forces between Two Cellulose Surfaces and between One Cellulose and One Mineral Surface

The effect of a cationic polyelectrolyte, PCMA, on the forces between two cellulose surfaces and between one cellulose surface and one mica surface has been studied using the interferometric surface force apparatus (SFA). The cellulose surfaces were prepared by Langmuir-Blodgett deposition of trimethylsilyl cellulose onto hydrophobized mica. Prior to measurements the surfaces were desilylated to obtain pure cellulose. Introduction of a cationic polyelectrolyte into the solution drastically changed the interactions between the cellulose layers. It was found that the cationic polyelectrolyte does adsorb onto the cellulose surface, although the adsorbed amount is low. The adsorbed layer is very thin, as expected at a low electrolyte concentration. Before the adsorption has reached equilibrium, when only some polyelectrolyte had adsorbed, the adhesion between the surfaces was high, and it was noted that the cellulose layer was damaged on separation. After a longer adsorption time an electrostatic repulsion and no adhesion were observed between the polyelectrolyte-coated cellulose surfaces. An electrostatic repulsion was observed between cellulose and mica. When cationic polyelectrolyte was introduced to the system it overcompensated the charges on both surfaces, and the range and magnitude of the double-layer force was higher than without polyelectrolyte. The relevance of the results to flocculation mechanism and efficiency in cellulose systems is discussed. Copyright 2000 Academic Press.     

Forces between surfaces in liquids

The results and implications of direct force measurements between molecularly smooth mica surfaces in liquids are reviewed. These discussions include four interactions fundamental to colloid science: van der Waals forces, double layer forces, adhesion forces and structural or solvation forces (e.g. hydration forces). Also considered are the effects of preferential surface adsorption of solute molecules on these interactions, e.g. surfactant adsorptions from aqueous solutions and water condensation from non-aqueous solvents.In aqueous media it is apparent that the DLVO theory is valid at all surface separations down to the “force barrier”, but that under certain conditions hydration forces can become significant at distances below 30 Å.The measured adhesion force between two solid surfaces can be simply related to their surface energies and where meniscus forces are also present due to “capillary condensation” from vapor solvent, their effect on adhesion can be understood in terms of straightforward bulk thermodynamic principles. Here, too, it is concluded that structural forces cannot be ignored.Our results suggest that structural forces may either very monotonically with distance or be oscillatory with a periodicity equal to the molecular size. Their origin, nature, mode of action and importance for particle interactions will no doubt take many years to sort out.     

Force measurements of bacterial adhesion on metals using a cell probe atomic force microscope

The adhesion of microbial cells to metal surfaces in aqueous media is an important phenomenon in both the natural environment and engineering systems. The adhesion of two anaerobic sulfate-reducing bacteria (Desulfovibrio desulfuricans and a local marine isolate) and an aerobe (Pseudomonas sp.) to four polished metal surfaces (i.e., stainless steel 316, mild steel, aluminum, and copper) was examined using a force spectroscopy technique with an atomic force microscope (AFM). Using a modified bacterial tip, the attraction and repulsion forces (in the nano-Newton range) between the bacterial cell and the metal surface in aqueous media were quantified. Results show that the bacterial adhesion force to aluminum is the highest among the metals investigated, whereas the one to copper is the lowest. The bacterial adhesion forces to metals are influenced by both the electrostatic force and metal surface hydrophobicity. It is also found that the physiological properties of the bacterium, namely the bacterial surface charges and hydrophobicity, also have influence on the bacteria-metal interaction. The adhesion to the metals by Pseudomonas sp. and D. desulfuricans was greater than by the marine SRB isolate. The cell-cell interactions show that there are strong electrostatic repulsion forces between bacterial cells. Cell probe atomic force microscopy has provided some useful insight into the interactions of bacterial cells with the metal surfaces.     

Adhesion Mechanisms of the Contact Interface of TiO(2) Nanoparticles in Films and Aggregates

Fundamental knowledge about the mechanisms of adhesion between oxide particles with diameters of few nanometers is impeded by the difficulties associated with direct measurements of contact forces at such a small size scale. Here we develop a strategy based on AFM force spectroscopy combined with all-atom molecular dynamics simulations to quantify and explain the nature of the contact forces between 10 nm small TiO(2) nanoparticles. The method is based on the statistical analysis of the force peaks measured in repeated approaching/retracting loops of an AFM cantilever into a film of nanoparticle agglomerates and relies on the in-situ imaging of the film stretching behavior in an AFM/TEM setup. Sliding and rolling events first lead to local rearrangements in the film structure when subjected to tensile load, prior to its final rupture caused by the reversible detaching of individual nanoparticles. The associated contact force of about 2.5 nN is in quantitative agreement with the results of molecular dynamics simulations of the particle-particle detachment. We reveal that the contact forces are dominated by the structure of water layers adsorbed on the particles' surfaces at ambient conditions. This leads to nonmonotonous force-displacement curves that can be explained only in part by classical capillary effects and highlights the importance of considering explicitly the molecular nature of the adsorbates.     

Capillary forces between surfaces with nanoscale roughness

The flow and adhesion behavior of fine powders (approx. less than 10 microm) is significantly affected by the magnitude of attractive interparticle forces. Hence, the relative humidity and magnitude of capillary forces are critical parameters in the processing of these materials. In this investigation, approximate theoretical formulae are developed to predict the magnitude and onset of capillary adhesion between a smooth adhering particle and a surface with roughness on the nanometer scale. Experimental adhesion values between a variety of surfaces are measured via atomic force microscopy and are found to validate theoretical predictions.     

Adhesion forces between functionalized latex microspheres and protein-coated surfaces evaluated using colloid probe atomic force microscopy

Proteins are important in bacterial adhesion, but interactions at molecular-scales between proteins and specific functional groups are not well understood. The adhesion forces between four proteins [bovine serum albumin (BSA), protein A, lysozyme, and poly-d-lysine] and COOH, NH2 and OH-functionalized (latex) colloids were examined using colloid probe atomic force microscopy (AFM) as the function of colloid residence time (T) and solution ionic strength (IS). For three of the proteins, OH-functionalized colloids produced higher adhesion forces to proteins (2.6-30.5 nN; IS=1 mM, T=10s) than COOH- and NH2-functionalized colloids (1.6-6.8 nN). However, protein A produced the largest adhesion force (8.1+/-1.0 nN, T=10 s) with the COOH-functionalized colloid, demonstrating the importance of specific and unanticipated protein-functional group interactions. The NH2-functionalized colloid typically produced the lowest adhesion forces with all proteins, likely due to repulsive electrostatic forces and weak bonds for NH2-NH2 interactions. The adhesion force (F) between functionalized colloids and proteins consistently increased with residence time (T), and data was well fitted by F=ATn. The constant value of n=0.21+/-0.07 for all combinations of proteins and functionalized colloids indicated that water exclusion and protein rearrangement were the primary factors affecting adhesion over time. Adhesion forces decreased inversely with IS for all functional groups interacting with surface proteins, consistent with previous findings. These results demonstrate the importance of specific molecular-scale interactions between functional groups and proteins that will help us to better understand factors colloidal adhesion to surfaces.     

Cell adhesion properties on photochemically functionalized diamond

The biocompatibility of diamond was investigated with a view toward correlating surface chemistry and topography with cellular adhesion and growth. The adhesion properties of normal human dermal fibroblast (NHDF) cells on microcrystalline and ultrananocrystalline diamond (UNCD) surfaces were measured using atomic force microscopy. Cell adhesion forces increased by several times on the hydrogenated diamond surfaces after UV irradiation of the surfaces in air or after functionalization with undecylenic acid. A direct correlation between initial cell adhesion forces and the subsequent cell growth was observed. Cell adhesion forces were observed to be strongest on UV-treated UNCD, and cell growth experiments showed that UNCD was intrinsically more biocompatible than microcrystalline diamond surfaces. The surface carboxylic acid groups on the functionalized diamond surface provide tethering sites for laminin to support the growth of neuron cells. Finally, using capillary injection, a surface gradient of polyethylene glycol could be assembled on top of the diamond surface for the construction of a cell gradient.     

Quantitative measure of nanoscale adhesion hysteresis by ultrasonic force microscopy

Adhesion hysteresis is the difference between the work used on separating two surfaces and the work gained on bringing them back together. Although much effort has been invested into adhesion hysteresis investigations at macroscales and microscales, its measurements at the nanolengths or even molecular lengths are still not easy. In this paper we demonstrate how to obtain quantitative measures of local adhesion hysteresis from ultrasonic force microscopy investigations. We derive analytical models fitting all the experimental cases and apply them to experimental data.     

Friction and adhesion forces of Bacillus thuringiensis spores on planar surfaces in atmospheric systems

The kinetic friction force and the adhesion force of Bacillus thuringiensis spores on planar surfaces in atmospheric systems were studied using atomic force microscopy. The influence of relative humidity (RH) on these forces varied for different surface properties including hydrophobicity, roughness, and surface charge. The friction force of the spore was greater on a rougher surface than on mica, which is atomically flat. As RH increases, the friction force of the spores decreases on mica whereas it increases on rough surfaces. The influence of RH on the interaction forces between hydrophobic surfaces is not as strong as for hydrophilic surfaces. The friction force of the spore is linear to the sum of the adhesion force and normal load on the hydrophobic surface. The poorly defined surface structure of the spore and the adsorption of contaminants from the surrounding atmosphere are believed to cause a discrepancy between the calculated and measured adhesion forces.