双组分茂金属催化剂催化乙烯聚合的研究

选择能形成支链的不对称桥联茂金属化合物Me2 C[(Cp) (Ind) ]ZrCl2 和非桥联的不同结构的茂金属化合物二氯二 (烯基取代环戊二烯 )锆如 ( Cp) 2 ZrCl2 ,(Cp) 2 ZrCl2 和 (Cp) 2 ZrCl2 ,以MAO为助催化剂 ,分别组成三组双组分茂金属催化剂的催化体系 ,催化乙烯聚合 .结果表明 ,两类催化剂组成的双组分茂金属催化体系催化乙烯聚合能得到支化的宽分子量分布的聚乙烯 ;聚合温度和改变两种茂金属催化剂的摩尔比对催化活性和分子量有很大影响 .因此可以利用改变双组分茂金属催化剂的摩尔比例和聚合温度来调控聚合物的分子量和分子量分布 .改变两种茂金属催化剂的摩尔比和聚合温度也能使聚合物的结晶度发生改变     

Gel Permeation Chromatography of Polyethylene Terephalate

Abstract

This paper describes the development of the gel permeation chromatography (GPC) technique for the measurements of cyclic trimer content, molecular weights, and molecular weight distribution of polyethylene terephthalate (PET), utilizing a solvent system of o-chlorophenol-chloroform. Mark-Houwink constants for this solvent system are also described.

The GPC technique was applied to the study of the cyclic trimer content, molecular weights and molecular weight distribution of a variety of commercial PET resins. The results indicate that the cyclic trimer content in PET is dependent on molecular weight, polycondensation process and catalyst system. Solidstate polymerized PET contains less cyclic trimer than PET made by the melt-phase process of the same molecular weight. The cyclic trimer content in solid-stated PET appears to be dependent on the conditions of solid-state polymerization.

The polydispersity index determine for a variety of PET samples is higher than the theoretically predicted value of 2.0; however, there is no systematic dependence on molecular weight or polycondensation process.     

Effect of styrene oligomers on syndiospecific polymerization of styrene

Styrene oligomers, preferentially consisting of styrene dimers and trimers, are formed by a free radical mechanism at the thermal polymerization of stabilizer-free styrene during storage and at higher polymerization temperatures. The identity of several dimer and trimer fractions formed in such a free radical polymerization, their influence on a coordinative polymerization reaction, the syndiospecific polymerization of styrene, as well as their effect on the properties of the resulting polymers has been investigated.Styrene dimers and styrene trimers reduce the polymerization activity of the transition metal catalyst significantly, especially at low amounts of oligomers added to the styrene. This behavior is discussed with respect to a proposed mechanism involving complexation of the active transition metal species with the specific oligomer instead of the styrene monomer, resulting in increased steric hindrance towards insertion of a styrene molecule to the active site.Both oligomers reduce the molecular weight of the syndiotactic polystyrene, by acting as chain-transfer agents. The constancy of the polydispersity over the whole concentration range of added dimer or trimer indicates that the uniformity of the active sites of the coordinative polymerization is not significantly influenced by the presence of the oligomers.The thermal properties of the polymers demonstrate that the oligomers do not affect the high syndiospecificity of the active catalytic sites, whereas the increase in crystallization temperature with increasing amounts of styrene dimer or trimer is comparable to effects observed by the addition of crystallization nucleators to semicrystalline polymers.     

Synthesis and polymerization of coupled compounds of 1,11-dodecadiyne

The dimer, trimer, and tetramer of 1,11-dodecadiyne, HC?C? (CH₂)₈? C?CH, were synthesized. The solid-state polymerization of the dimer was investigated by infrared (IR) spectroscopy. IR bands due to the diacetylene moiety were identified through the comparison of the IR spectra of the dimer, trimer, and tetramer. The dimer was found to have two polymorphs, melt-crystallized and solution-crystallized. Both of the polymorphs undergo solid-state polymerization by exposure to γ-ray or UV irradiation. The former has higher polymerizability for the diacetylene moiety than the latter. The solid-state polymerization of the terminal acetylene group was not observed. It is shown that the previously reported dimer structure in which both the diacetylene and terminal acetylene groups are polymerized to form an inherently electrically conducting polymer is incorrect. © 1995 John Wiley & Sons, Inc.     

含氮试剂对p-DCC/AlCl_3引发异丁烯正离子聚合的影响

以对-二枯基氯(DCC)/AlCl3体系引发异丁烯在二氯甲烷(CH2Cl2)正己烷(Hex)(40/60,V/V)混合溶剂中进行正离子聚合,探讨了DCC用量、含氮试剂2,6-二叔丁基吡啶(DtBP)和三苯胺(TPA)对异丁烯正离子聚合转化率、产物分子量及其分布的影响.结果表明,DCC和体系中微量水均可与AlCl3产生竞争络合,形成两种活性中心并引起相继的竞争引发,聚合产物的GPC谱图呈双峰分布,分子量分布宽;增加DCC用量有利于DCC与AlCl3的络合,致使链增长反应主要通过DCC与AlCl3络合形成的活性中心引发,但聚合产物分子量相对较低,分子量分布较宽;使用DtBP,可有效地抑制微量水引发及活性链向单体的转移反应,使分子量分布明显变窄,基本实现DCC的控制引发;采用DtBP与TPA共同调节聚合反应,可使聚合产物分子量分布变窄的同时,进一步提高分子量,从而得到相对较高分子量(Mw=103200)和单峰分子量分布(Mw/Mn=2.09)的聚异丁烯产物.     

环状碳酸酯低聚物的合成及其开环聚合的研究

环状碳酸酯低聚物的合成及其开环聚合的研究陈雨萍魏玮李革（中国科学院化学研究所工程塑料国家重点实验室北京１０００８０）关键词环状碳酸酯低聚物，聚碳酸酯，开环聚合环状单体的开环聚合在合成高聚物方面具有突出的优点，即在聚合过程中没有副产物、热效应低、聚合...     

Cationic polymerization of styrene by acetyl perchlorate: Molecular weight distribution of polystyrene and nature of the propagating species

To clarify the nature of the propagating species in cationic polymerization of styrene catalyzed by acetyl perchlorate, the molecular weight distribution of the polymer was investigated under various conditions. The molecular weight distribution curve for the polymer obtained in methylene chloride at 0°C showed a double peak phenomenon. This suggests that two or more kinds of propagating species participate simultaneously in the propagation reaction. The weight fraction W(H) of the polymer corresponding to the higher molecular weight peak increased with increasing polarity of the solvent. W(H) decreased when the concentration of the ionic species was increased either by an increase of the catalyst concentration or by the addition of the common salt such as tetra-n-butylammonium perchlorate. On the other hand, the position of the peak in the molecular weight distribution curve was independent of polymerization conditions. It was concluded that the higher molecular weight part of the polymer was produced under conditions for conductive to dissociation of the propagating species and the less dissociated propagating species was responsible for the lower molecular weight part of the polymer.     

Molecular weight distributions in radiation-induced polymerization. VII. γ-ray-induced polymerization of “wet” styrene in the solid state

In the present paper kinetic and molecular weight distribution results are reported for the γ-ray-initiated polymerization of styrene in the solid state. “In-source” polymerization over the temperature range ?35°C to ?55°C and post-polymerization at ?35°C have been investigated for “wet” styrene samples (water concentration ≈ 10^?3 mole/l.). An interesting feature of the solid-state polymerization of styrene is the bimodal nature of the molecular weight distribution. On a qualitative basis the results resemble those obtained previously for the polymerization of rigorously dried (“dry”) styrene. However, there are noticeable differences on a quantitative basis resulting from the considerable difference in the water content between wet and dry samples. On the basis of these studies, the kinetic and molecular weight distribution data have been interpreted as being indicative of polymerization occurring simultaneously via free-radical and cationic mechanisms.     

A novel scheme of heterogeneous polymerization of ethylene

The heterogeneous polymerization of ethylene initiated by radiation in tert-butyl alcohol was studied. The polymerization was carried out in a 100-ml reactor at 25–100°C and pressures of 200–300 kg/cm² in the presence of 50 ml of tert-butyl alcohol containing 7 wt-% water. The amounts of polymerized monomer, the average molecular weight of polymer formed, and the molecular weight distribution of polymer were measured at various stages of reaction and at various temperatures. The molecular weight distribution was found to be very much dependent on the reaction time and temperature. For the polymer formed at 50–60°C in the very early stages of reaction, the molecular weight distribution is unimodal, and in the intermediate stage a shoulder appears at a molecular weight higher than the first peak which increases as the polymerization proceeds; eventually a bimodal curve is formed. The bimodal distribution curves were analyzed to determine the fractions and average molecular weights of the each peak. On the basis of these data for the molecular weight distribution and kinetic behavior, a new scheme for the heterogeneous polymerization is proposed which indicates that the polymerization proceeds via propagating radicals in two different physical states, namely, loose and rigid states.     

Molecular weight distributions in radiation-induced polymerization. VI. γ-ray-induced polymerization of “dry” styrene in the solid state

The γ-ray-initiated polymerization of styrene in the solid state has been studied over the temperature range ?35°C to ?55°C for samples exhaustively purified and dried to remove residual water (“dry” samples). Comparison with kinetic results previously reported for dry samples in the liquid state indicates a sharp decrease in the rate of polymerization resulting from the liquid to solid state transition. The molecular weight distributions for in-source polymerization at ?35°C and ?40°C are bimodal in nature, and the appearance of a third peak is noticeable at ?47°C and ?55°C. In the case of postpolymerization at ?35°C the molecular weight distribution is bimodal as in the case of in-source samples. In the former case, however, the high molecular weight peak is predominant whereas the low molecular weight peak predominates in the latter. These results have been tentatively attributed to the postulated coexistence of two distinct propagating species which are radical and cationic in nature.     

Effect of the monomer concentration on piperylene cationic polymerization in the presence of the TiCl4-trichloroacetic acid catalytic system

The effect of the monomer concentration on the kinetics of cationic polymerization of piperylene in the presence of the TiCl₄-trichloroacetic acid catalytic system and molecular weight of the produced polymer was studied. At high monomer concentrations, the high-molecular-weight peak related to the formation of the branched fraction appears in the molecular weight distribution curve of the produced polymer. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1310–1313, July, 2007.     

γ- and ultraviolet-radiation-induced solid-state polymerization of maleimide in a few binary systems

The solid-state polymerization of maleimide by γ- and ultraviolet irradiation was carried out in binary systems with succinimide, maleic anhydride, and acenaphthylene. Polymaleimide obtained from the solid-state polymerization of maleimide by γ-rays was amorphous, while that obtained from the solid-state polymerization by ultraviolet rays was highly crystalline. In the maleimide–succinimide system the rate of polymerization reached a maximum nearly at the eutectic composition when the polymerization was carried out by γ-irradiation. With ultraviolet irradiation the rate of polymerization became higher with increasing content of succinimide in the feed. In the maleimide–maleic anhydride system a copolymer of both constituents was formed by γ-irradiation, but almost no homopolymer was produced. On the other hand, two kinds of polymers, a crystalline copolymer and an amorphous one, were produced by ultraviolet irradiation. The results were compared with those obtained from the copolymerization in solution. In the maleimide-acenaphthylene system the main products with ultraviolet irradiation was the dimer of acenaphthylene.     

Preparation of a uniform poly(methyl methacrylate) macromonomer and its polymerization

Syndiotactic poly(methyl methacrylate) (st-PMMA) macromonomer having methacryloyl end group was prepared from st-PMMA living anion and separated into uniform macromonomers by means of supercritical fluid chromatography. A uniform macromonomer with the degree of polymerization of 32 was polymerized radically in benzene at 60°C. The uniform dimer, trimer and tetramer of the uniform macromonomer were isolated from the polymerization product by means of gel-permeation chromatography (GPC). The intrinsic viscosity ([η]) in tetrahydrofuran of these uniform comblike polymers was determined by GPC/differential viscometric analysis. The plot of logarithmic [η] against logarithmic molecular weight indicated that the trimer and tetramer assume a little shrinking molecular shape as compared with the unimer and dimer.     

“LIVING-LIKE” CATIONIC POLYMERIZATION OF ISOBUTYL VINYL ETHER INITIATED BY CARBOXYL GROUPS ON CARBON BLACK SURFACE/ETHYLALUMINUM DICHLORIDE SYSTEM IN THE PRESENCE OF 1,4-DIOXANE

The effect of 1,4-dioxane as an added base on the cationic polymerization of isobutyl vinyl ether (IBVE) initiated by carboxyl groups on carbon black surface/ethylaluminum dichloride (EtAlCl₂) system was investigated. Although the cationic polymerization of IBVE by carbon black/EtAlCl₂ system the absence of 1,4-dioxane instaneously proceeded and the monomer conversion achieved 100% within a minute. The molecular weight distribution (MWD) of polyIBVE obtained was very broad. On the contrary, the MWD of polyIBVE obtained was very narrow and narrower than that obtained from the carbon black/ZnCl₂ initiating system by the addition of 1,4-dioxane. The number-average molecular weight (Mn) of polyIBVE obtained was directly proportional to monomer conversion in the cationic polymerization. However, the Mn of polyIBVE obtained from the polymerization by the initiating system in the the presence of 1,4-dioxane was smaller than that of the calculated value, assuming that polyl(IBVE) chain forms per unit carboxyl group on carbon black surface. It was concluded that carbon black/EtAlCl₂ initiating systems in the presence of 1,4-dioxane has an ability to initiate “living-like” cationic polymerization of IBVE based on the above results. PolyIBVE was grafted onto a carbon black surface after quenching the above “living-like” cationic polymerization systems with methanol.     

Mechanistic studies of the oxidative coupling polymerization of phenols. VI. Comparison of reactivities of DMP,PPO-dimer,and -trimer in the copper-catalyzed oxidative coupling polymerization

In the oxidative coupling polymerization, catalyzed by copper-amine complexes, the oxidation rates of 2,6-dimethylphenol (DMP) and its C? O-coupled dimer [4-(2′,6′-dimethylphenoxy)-2,6-dimethylphenol] and trimer [4-(-4′-(2″,6″-dimethylphenoxy)-2′,6′-dimethylphenoxy))-2,6-dimethylphenol] have been determined. The DMP concentration dependence shows a Michaelis–Menten-type behavior. On the other hand, the dimer and trimer showed a first-order rate-dependence in the respective phenol concentrations. This indicates that the slow reaction step, following an equilibrium complex formation between DMP and copper complex, is relatively fast for both the dimer and the trimer. Therefore, coordination of dimer or trimer to the copper complex appears to be rate-determining. Furthermore, the dimer and trimer gave overall reaction rates approximately eight times higher than found for DMP. Following the Flory principle of equal reactivity for functional groups of oligomers in polycondensations, all PPO oligomers can be assumed to have equally high oxidation rates as the dimer and trimer. The yield of undesired DPQ side product is strongly reduced when starting with the dimer (0.18%), or trimer (0.17%), compared to 3.3% for DMP. This is not unexpected, since DPQ can only be formed from two monomeric DMP residues. In fact, using a 1/10 molar mixture of dimer/DMP already results in a DPQ yield of only 1.7%. Furthermore, when starting from DMP, it has been observed that DPQ was predominantly formed during the first 30% conversion. Starting from dimer (or trimer) DPQ was formed at an almost constant very low rate during the whole course of the reaction. From these experiments it can be concluded that the most important polymerization reaction involves oxidation of copper-coordinated DMP anion to its corresponding cations, followed by coupling with a copper coordinated PPO chain.     

On-Water Polymerization of Phenylacetylene Catalyzed by Rh Complexes Bearing Strong π-Acidic Dibenzo[a,e]cyclooctatetraene Ligand

A series of new mononuclear neutral and water-soluble cationic rhodium (Rh) complexes bearing strong π-acidic dibenzo[a,e]cyclooctatetraene (dbcot) diene ligand have been synthesized and structurally characterized. In the polymerization of phenylacetylene, the dbcot Rh complex exhibits higher catalytic activity than the corresponding cod-based Rh complex in both of organic solvent and aqueous media, affording the high cis-transoidal PPAs with up to 99% of cis-contents, moderate molecular weights, and moderate to broad molecular weight distributions. Moreover, on-water polymerization of substituted phenylacetylenes is achieved by these complexes under air atmosphere, in which 3- to 163-fold acceleration of the polymerization rate is observed in aqueous polymerization compared to that in organic solvents. The nature of the Rh complex, solvent, polymerization temperature, and substituted group on the phenylacetylene impact on the polymer's yield, stereoselectivity, molecular weight, and molecular weight distribution. In addition, the water-soluble cationic Rh complexes can be reused for three times. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 716–725     

Cationic polymerization of p-substituted α-methylstyrenes. III. Effect of polymerization conditions on tacticity and molecular weight for p-chloro-α-methylstyrene

The cationic polymerization of p-chloro-α-methylstyrene was investigated for the effect of initiator and solvent on polymer tacticity, molecular weight, and molecular weight distribution. The products were generally crystalline polymers of 80–90% syndiotactic content with fairly high molecular weights and broad molecular weight distributions. Tacticities and molecular weight distributions followed similar patterns suggesting that the effect of reaction conditions on ionpair end-group structures was the dominant factor.     

Isolation and identification of the linear and cyclic oligomers of poly(ethylene terephthalate) and the mechanism of cyclic oligomer formation

Chromatographic techniques are described which can be used to isolate and identify the linear and the cyclic oligomers of poly(ethylene terephthalate). Extraction of the oligomers from high molecular weight polymer produces at least eight different cyclic species, some of which are isolated and identified. The cyclic dimer, the cyclic trimer, and the cyclic tetramer of poly(ethylene terephthalate) have also been prepared by acid chloride esterification and transesterification. Similar materials can be isolated from the ethylene glycol distillate obtained from the polymer melt. The mechanism of cyclic oligomer formation has been studied by determining the rate of formation of the cyclic oligomers during polymerization and during melt extrusion of polyesters which did not initially contain cyclic oligomers. The rate of formation depends upon the concentration of hydroxyl groups; hence, the cyclic oligomers are formed by transesterification from the chain ends or cyclodepolymerization. Therefore oligomers are inevitably produced during polymerization.     

Radiation-induced polymerization at high dose rate. VI. Butadiene in n-hexane solution

Polymerization of butadiene by electron-beam irradiation was studied in n-hexane solution. Kinetic features of the polymerization and microstructure of the product were similar to those in bulk polymerization, which indicated a cationic mechanism. Both the rate of polymerization and average molecular weight of the product decreased by about 20% in the solution system. Soluble polymer was obtained up to ca. 40% conversion at the monomer concentration of 50 mol%, whereas in the bulk system the gel formed in polymer conversion exceeded 10%. A kinetic equation was proposed to explain the change in rate of polymerization with the monomer concentration.     

Cationic polymerization of formaldehyde in liquid carbon dioxide. Part I

A cationic polymerization of formaldehyde which gave a high molecular weight polymer was studied in liquid carbon dioxide at 20–50°C. In the polymerization without any catalyst both the rate of polymerization and the molecular weight of the resulting polymer increased rapidly with a decrease in the loading density of the monomer solution to the reaction vessel, and also increased with an increase in the initial monomer concentration. From these results it was concluded that the initiating species could be ascribed to an impurity contained in the monomer solution. Both the rate of polymerization and the degree of polymerization of the polymer also increased with rising temperature. The carboxylic acid added acted as a catalyst in the polymerization because of increase in the polymer yield, the molecular weight of polymer formed, and the number of moles of polymer chain with increasing dissociation constant of acid used. It was concluded that the polymerization in liquid carbon dioxide proceeded by a cationic mechanism. Methyl formate had no influence on the polymerization, but methanol and water acted as a chain-transfer agent.