Correlation techniques in dynamic light scattering

The motion of small scatterers in a laser beam results in Doppler shifts of the scattered light. Various homodyne or heterodyne experiments may be used to measure such shifts. The stochastic nature of spatial particle arrangements and of the photon-detection process leads to statistic data processing schemes like temporal correlation or the computation of structure functions. Photon correlation is one of these schemes and has found numerous applications in velocimetry and Brownian motion studies. Topics of current interest are dead-time corrections, the use of photon structure functions, and multiple tau measurements, which access large ranges of time constants in a single run.More recent data processing techniques are recurrence rate correlation for the immediate determination of velocity correlation functions in seeded fluid flows and the measurement of amplitude-weighted phase structure functions, which is able to resolve very small particle displacements otherwise completely obscured by random Brownian motion. Rate correlation found applications in hydrodynamic studies of the route to turbulence, while the major use of phase structure function processing is a very significant increase in the sensitivity of electrophoretic mobility measurements by light scattering.     

Dynamics of two-phase swirling flow in a vortex chamber with a lower end swirler

The Particle Image Velocimetry (PIV) technique and laser Doppler anemometer (LDA) were used to measure the components of tangential and axial velocities of gas and particles in a vortex chamber with a fluidized bed, particle layer dynamics was estimated qualitatively, and the flow in the vortex chamber with a centrifugal fluidized bed of solid particles was simulated numerically. It is shown that with the growth of gas velocity in the swirler slots, the rotation velocity of bed grows almost linearly, and with an increasing bed mass, the rotation velocity decreases. Data on distributions of the volume fraction of particles and gas flow velocity inside the bed were obtained by numerical calculation.     

Scanning acoustic Doppler microscopy and scanning acoustic correlation microscopy

Acoustic microscopy with vector contrast at 100 MHz in a fluid with immersed particles is used to detect the flow profile in front of a microscopic orifice. The velocity profile concerning the component in axial direction of the focused beam is derived from the phase contrast. Possibilities to resolve the flow profile also for the components in normal direction with respect to the axis are demonstrated. The methods concerning measurement techniques and data evaluation for scanning acoustic Doppler microscopy are presented. For scanning acoustic correlation microscopy the time dependent phase and amplitude signals resulting from sound waves scattered by the immersed particles (aluminium flakes with a typical diameter of 10 microm) have been analysed by correlation procedures. From the obtained autocorrelation functions the velocity distribution can be derived. Both methods can be applied simultaneously. Data analysis is based on the information contained in the originally obtained images in vector contrast derived from temporal and spatial resolved analogue and digital processing of the acoustic signals.     

Laser light scattering and correlation techniques for characterization of colloidal suspensions

Particle motion in colloidal suspensions causes Doppler shifts in scattered laser light. For pure diffusion, the resulting spectral broadening may be measured by intensity interferometry and photon correlation techniques. Measured line widths or decay times yield particle size information. Electrophoretic mobilities may be determined, if an electric field is applied to the suspension. However, resulting line shifts can be extremely small and real-time optical phase processing may be required to resolve it. Finally, information about particle interactions may be obtained by studying angular cross sections or by photon correlation measurements on a small number of particles, i.e. using a very small scattering volume.Dedicated to Professor Harry Thomas on the occasion of his 60th birthday     

Novel processing tools for automated doppler picture veocimetry (DPV) evaluation

A unique technique, the Doppler Picture Velocimetry (DPV), for measuring and visualizing velocities especially in hypersonic gas flows is presented. By means of a Michelson interferometer (MI) the Doppler shifted light scattered by tracers is transformed into an image showing Fizeau fringes. The image fringe distribution provides information on the Doppler frequency shift which is related to the velocity of the particles crossing a light sheet plane. To overcome former disadvantages of DPV, the optical set-up as well as the processing scheme have been improved significantly. Two schemes have been tested in recent times for fringe processing: 1) an alternative process, the Least Square Estimators (LES) and 2) an algorithm based on a technique using Fast Fourier Transformations (FFT) to examine the DPV images in the frequency domain. The new DPV algorithms now allow an automated calculation of the velocity profiles from the Doppler pictures without manual fringe tracing as it had to be done in the past. Both methods are compared by means of Mach 6 flows around a wedge and a sphere produced in the ISL high energy shock tunnel STA. TiO₂ particles are illuminated by a laser light sheet which was perpendicularly arranged to the main flow direction. Light observation via the MI from the side (90° to illumination) informs on the vertically oriented velocity through the DPV images.     

Vortex shedding process investigation downstream a surface-mounted block

The laminar flow around a surface-mounted block is investigated by visualizations and PIV measurements. Flow topology and, especially, the vortex shedding dynamics are emphasized. The existence of two vortex shedding processes is highlighted by particles visualizations and instantaneous velocity fields analyses. On one hand, a dominant swirling mechanism with vortex matching process and a symmetrical topology sets up and, on the other hand, a non periodical evolution with a dissymmetric topology exist. In order to inquire about those processes, double velocity correlation functions are calculated and from those new data the space and time evolutions of the vortices are detailed.     

Velocity and density field measurements by digital speckle method

Velocity and density field measurements based on image processing of laser speckle or pseudo-speckle pattern have been developed. Laser speckle velocimetry (LSV) or white-light speckle velocimetry (WSV), which corresponds to a high-image-density PIV, gives a local velocity vector map or whole field velocity contour map of a two-dimensional flow field seeded densely with fine particles. This technique has an advantage in high-speed flow measurement without limit of frame rate except for directional ambiguity. New techniques of laser speckle photography and laser speckle interferometry by means of digital image processing have been developed recently for density field measurements. In laser speckle photography, a local density gradient vector map is reconstructed by cross-correlation evaluation between the reference and the object speckle patterns. In laser speckle interferometry, an equi-density contour map is reconstructed by image subtraction between the reference and the object interferometric speckle patterns.     

Investigation of the Flow Field in the Upper Part of a Cyclone with Laser and Phase Doppler Anemometry

The cyclone is a well known apparatus for separating particles out of a gas stream. With the modern laser diagnostic technologies of laser and phase Doppler anemometry (LDA and PDA), there is the potential to measure the flow and particle field inside the cyclone. The gas phase only measurements used micron‐sized oil seeding droplets, whereas the solid phase, chosen for the PDA particle size measurements, was limestone powder. To assess the possibility of measuring milled limestone particles with PDA, the measured size distribution was compared with those obtained by laser diffraction. The measurements inside the cyclone showed that the flow field in the upper part of the cyclone was different to that commonly thought. Therefore, the vertical height of the cyclone's vortex finder could be shortened without deterioration of the separation efficiency. The particles found in the hold‐up of the cyclone air flow were considerably larger than the average particle size in the feed pipe.     

旋流泵无叶腔内盐析颗粒湍流脉动特性研究

盐析晶体颗粒脉动特性是研究湍流输运状态下盐析过程的重要问题之一.为探索泵内盐析晶体颗粒湍流脉动规律及其对液相流场的影响,采用相位多普勒粒子速度场仪对旋流式输送泵无叶腔内的盐析湍流流场进行了测量,通过对改变泵运行工况、运行介质温度后颗粒脉动速度分布情况的分析,初步掌握了无叶腔中盐析晶体颗粒的湍流脉动特性;同时,讨论了晶体颗粒存在对液相湍流结构的影响。实验结果表明,随着流量的增加,颗粒的周向、径向及轴向脉动速度相应提高;盐析颗粒脉动速度值随温度发生变化,较高温度时速度脉动也较大;在一定条件下,盐析晶体颗粒表现出抑制湍流的行为。     

固体火箭发动机羽流流速TDLAS测量方法研究

针对现有对固体火箭发动机推进剂燃烧时产生的羽流流速测量方法的不足，提出了将可调谐半导体激光吸收光谱（TDLAS）技术应用于羽流流速的测量方法，通过测量燃烧产物中H₂O分子位于1 392 nm处的单根吸收谱线特征，根据多普勒效应建立的光谱频移和分子速度之间的关系来获得气流流速，解决了接触式测量方法会干扰羽流场和传统非接触式测量中示踪粒子不均匀的问题，并且取得了有效试验数据，通过对试验数据进行分析处理，得到了发动机的羽流流速。     

激光多普勒测速实验系统的信号处理

本文详细报导了运用集成锁相环路在激光多普勒测速实验教学系统中实现多普勒信号频率跟踪处理的设计原理和具体实施方案。该处理方法将集成度较高的 L M5 6 5锁相环应用于系统 ,使系统具有电路简单、可靠、可实时测量和结果直观、易操作等特点     

Absorption and Scattering of Light by Highly Concentrated Two‐phase Flows

The spray cone emerging during an extended metal atomization process (called spray forming) has been investigated in order to quantify the influence of highly concentrated multiphase flows on phase‐Doppler‐anemometry (PDA) measurements. Using this non‐intrusive, optical measurement technique not only the local particle size and velocity distributions of the spray can be obtained but also additional information about the mass flux in the multiphase flow. Since standard phase‐Doppler systems can be easily applied to low concentrated particle systems (spherical particles with smooth surfaces and an optical transparent continuous phase taken for granted) the application of this measurement technique to highly concentrated multiphase flows is more complex. Both the laser light propagating from the PDA device to the probe volume and the scattered one going backward to the PDA receiving system are disturbed by passing the highly concentrated multiphase flow. The resulting significant loss in signal quality especially concerns the measurement of the smaller particles of the spray because of their reduced silhouette (in comparison with the bigger ones). Thus, the detection of the smallest particles becomes partially impossible leading to measurement of a distorted diameter distribution of the entire particle collective. In this study the distortions of the measured distributions dependent on the particle number concentration as well as on the path length of the laser light are discussed.     

Chirp heterodyne laser Doppler velocimeter using a powerful fibre-coupled green laser

The chirp heterodyne technique allows a directional discrimination of laser Doppler velocity measurements without the use of additional frequency shift elements. This paper presents, for the first time, the use of a chirp frequency-modulated solid-state laser, emitting in the green spectral range. Experimental results of a fluid flow measurement verify the function of the realised chirp heterodyne laser Doppler velocimeter.     

Studies of the dynamic behaviour of charged dust particles in high electric fields using laser Doppler velocimetry

As a preliminary study for the collection of dust particles in an electrostatic precipitator, laser Doppler velocimetry has been used to measure the velocity of small dust particles charged in the high electric field of a model electrostatic precipitator. A differential optical system is adopted for the velocimeter. The period-measuring system is used to analyse Doppler beat signals and to obtain velocity data from them. By means of the laser Doppler velocimeter, the dynamic behaviour of the velocity and direction of moving dust particles is fully revealed as a function of the applied electric voltage in the entire collecting space of the model electrostatic precipitator, and is shown in vectorial flow diagrams of particle velocity.     

基于1.5 μm多普勒激光雷达的飞机尾涡探测技术研究

为规避尾涡威胁,保障飞行安全,研究了飞机尾涡的激光探测技术.介绍了尾涡探测基本原理,给出了激光探测方式设计和探测系统参量选择.基于设计的尾涡激光探测方案,研究了飞机尾涡回波多普勒谱与机型参量、飞行参量以及环境参量间的关系,获得了尾涡的径向速度分布规律,建立了尾涡回波多普勒谱模型,选取最佳尾涡参量估计算法用于尾涡的全面表征|通过开展A340的尾涡探测外场实验验证了激光探测尾涡的可行性和尾涡参量估计算法的有效性.研究表明,尾涡回波多普勒谱值与径向速度的三次方成反比,与涡流环量的二次方成正比.     

The characterisation and application of a pulsed neodymium YAG laser DGV system to a time-varying high-speed flow

Doppler Global Velocimetry (DGV) is a whole-field measurement technique which has attracted significant interest from the fluid-flow research community since its introduction in 1991. Practical implementations of the methodology have focused on two principal laser light sources: the argon ion laser, applied to steady state or slowly varying flows; and the pulsed neodymium YAG laser for the measurement of instantaneous velocity fields. However, the emphasis in the published literature has been very much on research using the argon laser. This paper reports the application of a Q-switched, injection-seeded neodymium YAG laser to the proven Oxford DGV system, and the use of this combination in a short duration unsteady high-speed flow. The pertinent characteristics of the apparatus are described, and the impact of these on the integrity of the resulting velocity measurements is presented. Adaptations to the commercial laser system that make it suitable for application to the measurement of transient high-speed flows are described. Finally, the application of this system to a short duration unsteady flow is described. This application is based on the flow found in a new type of transdermal drug delivery device, where particles of the drug material are projected at high speed through the skin. Whole-field velocities are recorded, and values as high as 800 m/s are evident.     

Coherent Scattering by Multiple Particles in Phase Doppler Interferometry

A theoretical model has been developed for studying the response of the phase Doppler interferometer when multiple particles are simultaneously present within the measurement probe volume. The developed model incorporates the geometrical optics theory for describing the coherent interaction between the scattered light signals of multiple particles, eachhaving different size, velocity, trajectory, and arrival time. The resulting Doppler signal is processed by a theoretical signal processor which can simulate the performance characteristic of different signal processing schemes that are widely used in phase Doppler interferometry, namely, zero-crossing counter, covariance, autocorrelation and DFT parocessors. The application of the developed model for studying the coherent scattering by two particles has been specifically addressed in this paper. It has been shown that a DFT processor can be used to simultaneously measure the size and velocity of the two particles in most instances. However, for more than two particles, the signal processing scheme becomes more complex because of a quadratic increase in the beat frequency components.     

Flow Structure in a Ranque−Hilsch Vortex Tube

The structure of twisted flow in a Ranque?Hilsch vortex tube is investigated experimentally by modeling gas flow with an incompressible fluid flow. The velocity field is measured with a laser Doppler anemometer in the entire volume of the vortex chamber. The streamline pattern, which gives a complete presentation of the flow structure in the Ranque?Hilsch tube, is plotted in the axial section of the chamber. The resulting streamline pattern can serve as a basis for explaining the physical mechanism of the Ranque effect.     

Simultaneous measurement of particle size, velocity, andtemperature in thermal plasmas

The in-flight measurement of particle parameters (size, velocity, temperature, and local number density) can prove insight into the plasma processing of solid materials. A measurement technique for simultaneously obtaining the size, velocity, and temperature of particles entrained in high-temperature flow fields is described. Particle size and velocity are obtained from a combination laser-particle-sizing system and laser Doppler velocimeter. The particle temperature is determined by a two-color pyrometry technique and the data rate is a measure of relative particle number density. Typical measured temperatures and velocities for the 5-100 μm particles used in plasma spraying are 1600-3500 K and 100-300 m/s, respectively. Since particle size, velocity, and temperature are measured simultaneously, cold particles (<1600 K) are identified and their relative number density can be quantified. Data from two plasma spray systems, a metal one (Ni-Al) and a metal oxide one (Al₂O₃), are presented and their application to understanding the plasma spray-coating process is illustrated     

Measurement of flow and turbulence distribution of a free jet by laser photon correlation spectroscopy

The flow and turbulence profile of a free jet is reported by remote sensing techniques using laser Doppler effect and photon correlation spectroscopy.