Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

Determination of copper in powdered chocolate samples by slurry-sampling flame atomic-absorption spectrometry

Chocolate is a complex sample with a high content of organic compounds and its analysis generally involves digestion procedures that might include the risk of losses and/or contamination. The determination of copper in chocolate is important because copper compounds are extensively used as fungicides in the farming of cocoa. In this paper, a slurry-sampling flame atomic-absorption spectrometric method is proposed for determination of copper in powdered chocolate samples. Optimization was carried out using univariate methodology involving the variables nature and concentration of the acid solution for slurry preparation, sonication time, and sample mass. The recommended conditions include a sample mass of 0.2 g, 2.0 mol L^–1 hydrochloric acid solution, and a sonication time of 15 min. The calibration curve was prepared using aqueous copper standards in 2.0 mol L^–1 hydrochloric acid. This method allowed determination of copper in chocolate with a detection limit of 0.4 g g^–1 and precision, expressed as relative standard deviation (RSD), of 2.5% (n=10) for a copper content of approximately 30 g g^–1, using a chocolate mass of 0.2 g. The accuracy was confirmed by analyzing the certified reference materials NIST SRM 1568a rice flour and NIES CRM 10-b rice flour. The proposed method was used for determination of copper in three powdered chocolate samples, the copper content of which varied between 26.6 and 31.5 g g^–1. The results showed no significant differences with those obtained after complete digestion, using a t-test for comparison.     

Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

A multi-pumping flow system for chemiluminometric determination of ascorbic acid in powdered materials for preparation of fruit juices

A multi-pumping flow-based procedure with chemiluminescent detection is proposed for the determination of ascorbic acid, AA, in fruit juices (powdered form). The method relies on the inhibitory effect of AA on the oxidation of luminol by hydrogen peroxide in alkaline medium. The system comprises several discretely actuated solenoid pumps as the only active components. It handles 100 samples per hour, and requires 96 μl of sample, 42 μg of luminol and 105 μg of potassium hexacyanoferrate(III) per determination. The analytical curve is linear up to about 11 mmol l^− 1 AA, and detection limit is 0.17 mmol l^− 1 AA. The system yields precise measurements (r.s.d. < 1%; n = 11), and recovery ranges from 94% to 106%. Results are in agreement with the reference method (AOAC) at the 95% confidence level.     

Slurry-based procedures to determine chromium, nickel and vanadium in complex matrices by ETAAS

Two slurry-based ETAAS methodologies are compared to determine directly Cr, Ni and V in coal fly ash, soils and sediments: current slurry analysis (USS) and ‘slurry extraction’ (SE). Slurries for USS-ETAAS were prepared in 0.5% HNO₃. HF and HNO₃ were evaluated as chemical modifiers. HF was the extractant for the SE-ETAAS approach.A unique slurry-based procedure to measure Cr, Ni and V could not be established. Cr concentrations up to 100 μg g^{− 1} were accurately determined by USS (0.5% HNO₃; λ = 429.0 nm; LOD = 0.35 μg g^{− 1}) whereas higher contents required the SE procedure (sample grinding, 30% HF; LOD = 0.02 μg g^{− 1}). Both methods were appropriate to determine Ni (LOD = 0.11 and 0.08 μg g^{− 1}, for USS and SE, respectively). V was satisfactorily quantified only with the USS approach (LOD = 0.80 μg g^{− 1}).     

An improved procedure for phosphorous fractionation in plant materials exploiting sample preparation and monosegmented flow analysis

Sample treatment procedures were evaluated for fractionation of phosphorous in plant materials (determination of organic and inorganic, soluble and insoluble fractions). The procedures aimed the conversion of different species into orthophosphate, minimizing time, reagent amounts and waste generation. A monosegmented flow system with multicommutation was developed for the spectrophotometric determination of orthophosphate by the molybdenum blue method. Linear response within 0.5 and 25.0 mg L^− 1 P, detection limit of 24 μg L^− 1 P (99.7% confidence level), coefficient of variation of 3.5% (n = 10) and sampling rate of 38 measurements per hour were estimated. Each determination consumes 5.0 mg ascorbic acid and 0.60 mg of ammonium molybdate. Total phosphorous determination can be carried out after microwave-assisted acid digestion by employing 100 mg of plant material and 500 μL of concentrated HNO₃. Extraction of soluble phosphorous can be carried out with water by stirring for 10 min and organic soluble phosphorous can be determined either after microwave-assisted acid digestion or photodegradation in the presence of ammonium persulfate in acid medium. The results for the different fractions agreed with those obtained by ICP OES at the 95% confidence level.     

Mercury, zinc, manganese, and iron accumulation in leachate pond sediments from a refuse tip in Southeastern Brazil

This work evaluates Hg, Zn, Fe and Mn transfer from the leachate of a refuse tip based on their accumulation in a sediment core of 17 cm collected in a leachate pond of a small refuse tip ageing approximately 10 years. Sediment samples were digested with an acid mixture (50% acqua regia solution), heated at 70 °C during 1 h, in a thermal-kinetic reactor “cold finger”. The extract was analysed to obtain Hg content by cold vapour absorption atomic spectrometry (CVAAS). Fe, Mn and Zn contents were obtained by flame atomic absorption spectrometry (FAAS) after total decomposition of the samples. Concentration ranges along the core varied from 0.16 to 0.58 μg g^− 1; 7.3 to 145 μg g^− 1; 11.7 to 116 μg g^− 1 and 0.21% to 1.82% for Hg, Zn, Mn and Fe, respectively. All metals showed enrichment in the upper layers (above 6 cm) which probably correspond to the year 1996. Results indicated that Hg transfer is one order of magnitude higher than Zn and suggest that metals accumulation in sediments probably reduce their migration to groundwater.     

Indirect atomic absorption spectrometry (IAAS) as a tool for the determination of iodide in infant formulas by precipitation of AgI and redissolution with cyanide

A method to determine iodide in infant formula samples by indirect atomic absorption spectrometry (IAAS) was developed. The iodide in solution resulting from an alkaline digestion (Na₂CO₃–NaOH) of the sample is precipitated with silver; the precipitate is redissolved by adding cyanide solution, and this solution is subjected to GF-AAS. Temperatures of 1000 and 2100°C were selected for the ashing and atomization steps, respectively, using a mixture of Pd and Mg(NO₃)₂ as a matrix modifier (at concentrations of 36 and 16 μg ml⁻¹, respectively). The sensitivity, LOD, LOQ and characteristic mass obtained were, respectively, 1.12×10⁻² l μg⁻¹, 3.1 μg g⁻¹ and 10.4 μg g⁻¹ and 7.3 pg, referred to sample. The linear interval of concentrations extends up to 10 μg l⁻¹ of iodide, with no need to use the standard addition method; the mean R.S.D. of data within this range is 3.4%, with 2.9% over the whole procedure. No interfering effects were observed among the foreign ions studied, and 100.0% was the mean analytical recovery achieved within the linear range of concentrations. The application of the method to seven real samples gave a mean content of 12.8 μg g⁻¹ of iodide, as well as less than 3.1 μg g⁻¹ in eight other samples.     

Homogeneous liquid-liquid extraction combined with gas chromatography-electron capture detector for the determination of three pesticide residues in soils

In this study, a new method was developed for analyzing malathion, cypermethrin and lambda-cyhalothrin from soil samples by using homogeneous liquid–liquid extraction (HLLE) and gas chromatography with electron capture detector (GC–ECD). Acetone was used as extraction solvent for the extraction of target pesticides from soil samples. When the extraction process was finished, the target analytes in the extraction solvent were rapidly transferred from the acetone extract to carbon tetrachloride, using HLLE. Under the optimum conditions, linearity was obtained in the range of 0.05–40 μg kg⁻¹ for malathion, 0.04–10 μg kg⁻¹ for lambda-cyhalothrin and 0.05–50 μg kg⁻¹ for cypermethrin, respectively. Coefficients of correlation (r²) ranged from 0.9993 to 0.9998. The repeatability was carried out by spiking soil samples at concentration levels of 2.5 μg kg⁻¹ for lambda-cyhalothrin, and 10 μg kg⁻¹ for malathion and cypermethrin, respectively. The relative standard deviations (RSDs) varied between 2.3 and 9.6% (n = 3). The limits of detection (LODs), based on signal-to-noise ratio (S/N) of 3, varied between 0.01 and 0.04 μg kg⁻¹. The relative recoveries of three pesticides from soil A1, A2 and A3 at spiking levels of 2.5, 5 and 10 μg kg⁻¹ were in the range of 82.20–91.60%, 88.90–110.5% and 77.10–98.50%, respectively. In conclusion, the proposed method can be successfully applied for the determination of target pesticide residues in real soil samples.     

Development of an integrated flow injection system for the electro-oxidative leaching of uranium from geological samples and its spectrophotometric determination with Arsenazo III

This work proposes a new procedure for on-line electro-oxidative leaching and spectrophotometric determination of uranium in ore samples. By associating a conventional flow injection system, used for uranium determination with Arsenazo III, with an on-line system for electro-oxidative leaching, a fully integrated system was assembled. The systems were integrated after achieving optimum conditions for uranium determination and leaching. According to the results obtained in the present work, a current density of 280 mA cm⁻² generated enough hypochlorite ions in the electrolyte solution (3.6 mol L⁻¹ HCl + 2% (w/v) NaCl) to promote quantitative oxidation of U(IV) to U(VI) thus improving the extraction efficiency. The slurry density did not significantly affect the performance of the system and the increasing temperature resulted in a decrease in extraction efficiency. This methodology was applied in the determination of U₃O₈ in four ore samples and the results obtained agreed with those obtained by ICP-MS after conventional wet acid digestion of the samples.     

Selective separation of gold from iron ore samples using ion exchange resin

Gold in iron ore samples is separated from iron (major matrix cation), antimony and vanadium using anion exchange resin in (0.2 M) HBr, potassium peroxodisulfate and acetone:water:nitric acid media. The exchangeable anion Cl⁻ of the ion exchanger Dowex 1X 4 is replaced by Br⁻ using (6 M) HBr solution. Certified reference material DGP-M1, spiked ferric magnetic oxide, gold radioactive tracer ¹⁹⁸Au and gold standard solutions are used to study the adsorption efficiency and the yield recovery of tetrabromoaurate AuBr₄⁻ from the resin. Ten eluents have been tried to elute gold from the column, and it has been found that a 10 ml potassium peroxodisulfate and 240 ml acetone:water:nitric acid [125:5:5] solution fulfills the objective. The set up of the separation procedure allows quantitative adsorption of gold by the resin, while the major matrix cation (Fe) and others (Cd, Ag, Cu, V, Sb, Ti) have been passed through the column with the feeding solution (0.2 M) HBr. The resin selectivity coefficient (K) of separating Au from Fe has been found to be K_Fe^Au≈6.4×10¹¹. The eluted Au is treated with K₂S₂O₈ and H₂O₂ for spectrophotometric determination as rhodamine-B complex at 555.6 nm. The linearity, detection limit, precision, and accuracy of the determination method have been found to be up to 2.0 μg g⁻¹, 0.018 μg g⁻¹, 0.009 μg g⁻¹ and 3%, respectively.     

Simultaneous determination of gibberellic acid, indole-3-acetic acid and abscisic acid in wheat extracts by solid-phase extraction and liquid chromatography-electrospray tandem mass spectrometry

A liquid chromatography–tandem mass spectrometry (LC–MS/MS) method was developed for simultaneous determination of three representative phytohormones in plant samples: gibberellic acid (GA₃), indole-3-acetic acid (IAA) and abscisic acid (ABA). A solid-phase extraction (SPE) pretreatment method was used to concentrate and purify the three phytohormones of different groups from plant samples. The separation was carried out on a C₁₈ reversed-phase column, using methanol/water containing 0.2% formic acid (50:50, v/v) as the isocratic mobile phase at the flow-rate of 1.0 mL min⁻¹, and the three phytohormones were eluted within 7 min. A linear ion trap mass spectrometer equipped with electrospray ionization source was operated in negative ion mode. Selective reaction monitoring (SRM) was employed for quantitative measurement. The SRM transitions monitored were as 345 → 239, 301 for GA₃, 174 → 130 for IAA and 263 → 153, 219 for ABA. Good linearities were found within the ranges of 5–200 μg mL⁻¹ for IAA and 0.005–10 μg mL⁻¹ for ABA and GA₃. Their detection limits based on a signal-to-noise ratio of three were 0.005 μg mL⁻¹, 2.2 μg mL⁻¹ and 0.003 μg mL⁻¹ for GA₃, IAA and ABA, respectively. Good recoveries from 95.5% to 102.4% for the three phytohormones were obtained. The results demonstrated that the SPE-LC–MS/MS method developed is highly effective for analyzing trace amounts of the three phytohormones in plant samples.     

Chitosan–magnetite nanocomposites (CMNs) as magnetic carrier particles for removal of Fe(III) from aqueous solutions

This research focuses on removal of Fe(III) from aqueous solution using chitosan–magnetite nanocomposites as potential sorbent. The presence of nanosized magnetic particles within the nanocomposites was confirmed by TEM and SAED analysis. The particles with diameter 508 μm and 84 μm, follow Frendlich sorption isotherm at 30 °C, and the Frendlich constants (K_F, 1/n) have been found to be 5.974 mg g⁻¹, 2.66 and 35.98 mg g⁻¹, 1.385, respectively. Out of various kinetic models, the experimental data for dynamic uptake of Fe(III) is best fitted on ‘pseudo-second order’ kinetic model. The linear nature of plots between log (% sorption) and log (time) is indicative of intra-particle diffusion. For the particles with diameters 508 μm and 84 μm, the value of k_id was found to be 1.78 mg l⁻¹ min^−0.5 and 2.13 mg l⁻¹ min^−0.5. The sorption mean free energy from the Dubinin–Radushkevic isotherm was found to be 7.04 kJ mol⁻¹ indicating chemical nature of sorption. The increase in chitosan content in sorbent particles is found to enhance the Fe(III) uptake. The various thermodynamic parameters have also been evaluated. Finally, the presence of Cu²⁺ ions in the sorbate is found to decrease the uptake of Fe(III).     

A rapid technique for determination of nitrate and nitric acid by acid reduction and diazotization at elevated temperature

A rapid technique for determination of nitrate by acid reduction and diazotization at elevated temperature has been standardized. The technique is based on quantitative diazotization of sulfanilamide by nitrate on incubation in boiling water bath for 3, 5 or 10 min in presence of high concentration of HCl, ca. 64.5%. The diazotized sulfanilamide is coupled at room temperature to N-1-(naphthyl)-ethylenediamine dihydrochloride, and the chromophore evaluated spectrophotometrically at 540 nm. The technique provides linear estimate of nitrate over the test range of 0.5 through 10 μg N mL⁻¹ sample with all test incubation time periods using alkali nitrate and nitric acid as sources of nitrate anion. Urea treatment enables selective determination of nitrate in presence of nitrite with overall 99 ± 1% recovery, and without affecting nitrate determination (P > 0.1) or its regression coefficient. The technique has obvious advantages over metal-reduction technique. It is simple, rapid, selective in presence of nitrite, and an inexpensive method for routine determination of nitrate with detection range 0.5–10 μg N mL⁻¹ sample. Besides, the technique provides opportunity to detect nitric acid as low as 35 μM even in presence of other acids.     

Screening method for phthalate esters in water using liquid-phase microextraction based on the solidification of a floating organic microdrop combined with gas chromatography-mass spectrometry

A simple and efficient liquid-phase microextraction (LPME) technique was developed using directly suspended organic microdrop coupled with gas chromatography–mass spectrometry (GC–MS), for the extraction and the determination of phthalate esters (dimethyl phthalate, diethyl phthalate, diallyl phthalate, di-n-butyl phthalate (DnBP), benzyl butyl phthalate (BBP), dicyclohexyl phthalate and di-2-ethylhexyl phthalate (DEHP)) in water samples. Microextraction efficiency factors, such as nature and volume of the organic solvent, temperature, salt effect, stirring rate and the extraction time were investigated and optimized. Under the optimized extraction conditions (extraction solvent: 1-dodecanol; extraction temperature: 60 °C; microdrop volume: 7 μL; stirring rate: 750 rpm, without salt addition and extraction time: 25 min), figures of merit of the proposed method were evaluated. The values of the detection limit were in the range of 0.02–0.05 μg L⁻¹, while the R.S.D.% value for the analysis of 5.0 μg L⁻¹ of the analytes was below 7.7% (n = 4). A good linearity (r² ≥ 0.9940) and a broad linear range (0.05–100 μg L⁻¹) were obtained. The method exhibited enrichment factor values ranging from 307 to 412. Finally, the designed method was successfully applied for the preconcentration and determination of the studied phthalate esters in different real water samples and satisfactory results were attained.     

Application of three-variables Doehlert matrix for optimisation of an on-line pre-concentration system for zinc determination in natural water samples by flame atomic absorption spectrometry

This article describes an on-line pre-concentration system for zinc determination in environmental samples by flame atomic absorption spectrometry (FAAS). It was based on the sorption of zinc(II) ions in a minicolumn of polyurethane foam loaded with 4-(2-pyridylazo)-resorcinol (PAR). The optimisation step was carried out using two-level full factorial and a Doehlert design. Three variables (sampling flow rate, buffer concentration and pH) were regarded as factors in the optimisation. Results of the two-level full factorial design 2³ for 8 runs (in duplicate) based on the Analysis of Variance (ANOVA) demonstrated that all the factors in the tested levels are statistically significant. Besides, the interaction (sampling flow rate×buffer concentration) was also statistically significant. A three-variables Doehlert design was applied in order to determine the best condition for pre-concentration and determination of zinc. The validation process was assessed as: parameters of the analytical curve, precision, effect of other ions in the proposed system, robustness test and accuracy. The proposed system allowed determination of zinc with detection limit (3σ/S) of 0.28 μg l⁻¹, and a precision (reproducibility), calculated as relative standard deviation (R.S.D.) of 10.0 and 3.7% for zinc concentration of 1.0 and 5.0 μg l⁻¹, respectively. The achieved pre-concentration factor was 91.23 and the sampling frequency was 48 samples per hour. The achieved recovery for zinc determination in presence of several cations demonstrated that this procedure could be applied for analysis of water samples. The accuracy was confirmed by analysis of three certified reference materials. This procedure was applied for zinc determination in several kinds of water samples including saline aqueous waste from oil Refinery.     

Use of a graphite–polyurethane composite electrode for electroanalytical determination of indole-3-acetic acid in soil samples

A new electroanalytical methodology was developed for the quantification of the phytohormone indole-3-acetic acid (IAA), using a graphite–polyurethane composite electrode (GPU) and the square wave voltammetry (SWV), in 0.1 mol L^− 1 phosphoric acid solution (pH 1.6). Analytical curves were constructed under optimized conditions (f = 100 s^− 1, a = 50 mV, E_i = 5 mV) and the reached detection and quantification limits were 26 μg L^− 1 and 0.2 mg L^− 1, respectively. The developed methodology is simple and accurate for the routine determination of IAA. In order to verify the application of the electroanalytical methodology in fortified soil samples without previous treatment, an IAA assay was performed without serious interferences of the soil constituents.     

Determination of As, Ge, Hg, Pb, Sb, Se and Sn in coal slurries by CVG-ETV-ICP-MS using external or isotopic dilution calibration

A method for the multi-elemental determination of As, Ge, Hg, Pb, Sb, Se and Sn in coal reference materials by slurry sampling chemical vapor generation (CVG) using external calibration and isotopic dilution (ID) calibration and detection by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) is proposed. As, Ge, Sb, Se and Sn were determined using the external calibration, while, Hg, Pb, Se and Sn were determined by isotopic dilution. About 50–250 mg of sample was mixed with an acid solution, containing aqua regia and HCl, in an ultrasonic bath. For the isotopic dilution calibration, the enriched isotopes ²⁰¹Hg, ²⁰⁶Pb, ⁷⁷Se and ¹¹⁹Sn were added to the slurry in an adequate amount in order to produce an altered isotopic ratio close to 1. The vapor produced by the reaction of the sample slurry with the reducing agent was transported to the vaporizer and trapped in a Ir-treated graphite tube at 200 °C, before vaporization at 2100 °C and transportation of the vapor to the plasma. The accuracy of the method was assured by the analysis of four certified reference coal samples, using external calibration with aqueous solutions, prepared in the same medium and subjected to the same CVG and trapping procedure as the slurries and also by isotopic dilution calibration. The obtained concentrations were in agreement with the certified values, using the t-Student test for a confidence level of 95%. The detection limits (3 s; n = 5) of isotopic dilution, in ng g^− 1, were: 0.4 for Hg, 900 for Pb, 0.3 for Se and 0.2 for Sn. For external calibration, the detection limits, in ng g^− 1, were: 1.6 for As, 0.1 for Ge, 0.3 for Sb, 0.9 for Se and 7.5 for Sn. The relative standard deviations generally were lower than 14%, adequate for slurry analysis.     

Determination of Fe, Ni and V in asphaltene by ICP OES after extraction into aqueous solutions using sonication or vortex agitation

A simple procedure for the extraction of Fe, Ni and V from asphaltene into acid solutions prior to the ICP OES determination is proposed. Either sonication or vortex agitation was used to disperse the organic sample into concentrated nitric acid, achieving efficient analyte extraction into the aqueous acid solution. Both procedures were compared and the advantage of the ultrasound-assisted procedure was evaluated. In both cases, pre-heating of sample–acid mixtures was necessary to enable quantitative extractions. Optimized conditions for the ultrasonic bath were established: 1 L of water at room-temperature, 20 min of sonication and tubes (maximum of eight) in vertical position. By using the vortex, 50 min of vigorous mechanical agitation was needed for each one of the tubes containing samples. The acid solution obtained after extraction was directly aspirated into the ICP in order to perform quantification by optical emission. Calibration was made with aqueous analyte standards containing Sc as internal standard. The procedures were tested using certified fuel oil (SRM NIST 1634c) and the method was applied for the determination of Fe, V and Ni in one asphaltene sample obtained by the fractionation of the SRM NIST 1634c. Recoveries above 90% were achieved and limits of quantification in the asphaltene sample were 1.5, 15 and 1.0 μg g^− 1 estimated for Fe, Ni and V, respectively.     

Fabrication of a template-synthesized gold nanorod-modified electrode for the detection of dopamine in the presence of ascorbic acid

Gold nanorods (GNRs) with suitable aspect ratio were synthesized with a template technique and then dispersed in a saturated sodium citrate solution by ultrasonication to form a GNR suspension. A GNR-modified electrode was fabricated using the GNR suspension. The oxidation of dopamine at the GNR/GC electrode exhibited surprisingly high electrocatalytic activity and adsorption-controlled characteristics. Square-wave voltammetry was used to detect dopamine. At the GNR/GC electrode, the linear concentration range of DA is from 1 × 10⁻⁸ M to 1 × 10⁻⁷ M and the detection limit (s/n = 3) is as low as 5.5 × 10⁻⁹ M. The current sensitivity is 3.280 μA/μM, and 1000-fold ascorbic acid (AA) cannot interfere with the determination of DA. All these performances are greatly superior to those of the bare GC electrode.