Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Synthesis and properties of novel polyimides from sulfonated binaphthalene dianhydride for proton exchange membranes

A sulfonated dianhydride monomer, 6,6′‐disulfonic‐4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (SBTDA), was successfully synthesized by direct sulfonation of the parent dianhydride, 4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (BTDA), using fuming sulfuric acid as the sulfonating reagent. A series of sulfonated homopolyimides were prepared from SBTDA and various common nonsulfonated diamines. The resulting polymer electrolytes, which contain ion conductivity sites on the deactivated positions of the aryl backbone rings, displayed high proton conductivities of 0.25–0.31 S cm^?1 at 80 °C. The oxidative stability test indicated that the attachment of the ? SO₃H groups onto the dianhydride units did not deteriorate the oxidative stability of the SPI membranes. The better membranes were achieved by the copolymerization of nonsulfonated diamine, SBTDA, and BTDA. Copolymer membrane synthesized from hexane‐1,6‐diamine, SBTDA, and BTDA displayed excellent water stability of more than 1000 h at 90 °C, while its proton conductivity was still at a high level (comparable to that of Nafion 117). Furthermore, the novel block copolymer ( II‐b ) displayed higher proton conductivity compared with the random one ( II‐r ) obviously, probably due to the slightly higher water uptake and better microphase separated morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2820–2832, 2008     

Synthesis and characterization of polyimide‐polysiloxane segmented copolymers for fuel cell applications

Sulfonated polyimides exhibit high strength, good film‐forming ability, chemical resistance, and, in their hydrated state, relatively high proton conductivity. Here we report the one‐pot synthesis of sulfonated polyimide‐polysiloxane segmented copolymers through the reaction of a dianhydride with a mixture of three diamines: a nonionic aromatic diamine (4,4′‐oxydianiline), a sulfonated diamine (4,4′‐diamino‐2,2′‐biphenyldisulfonic acid), and a telechelic diamino polysiloxane. Copolymer compositions were evaluated using ¹H NMR and size‐exclusion chromatography. The presence of ion‐containing diamines in the reaction mixture inhibited stoichiometric incorporation of hydrophobic siloxane segments. Siloxane segments were found to lower the thermal stability of the polyimide host. Copolymers with and without siloxane segments were cast into free‐standing films. Equilibrium water sorption studies of cast films show that, for the compositions studied here, the presence of siloxane segments does not interfere with water swelling, suggesting that a microphase‐segregated morphology may exist. TEM and SAXS analyses show evidence of phase‐segregation in sulfonated polyimides and reveal that siloxane segments strongly affect ionic clustering. However, proton conductivity only changes slightly when polysiloxane segments are incorporated. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3747–3758, 2007     

Synthesis and properties of novel sulfonated (co)polyimides bearing sulfonated aromatic pendant groups for PEFC applications

Novel sulfonated diamines bearing aromatic pendant groups, namely, 3,5‐diamino‐3′‐sulfo‐4′‐(4‐sulfophenoxy) benzophenone (DASSPB) and 3,5‐diamino‐3′‐sulfo‐4′‐(2,4‐disulfophenoxy) benzophenone (DASDSPB), were successfully synthesized. Novel side‐chain‐type sulfonated (co)polyimides (SPIs) were synthesized from these two diamines, 1,4,5,8‐naphthalene tetracarboxylic dianhydride (NTDA) and nonsulfonated diamines such as 4,4′‐bis(3‐aminophenoxy) phenyl sulfone (BAPPS). Tough and transparent membranes of SPIs with ion exchange capacity of 1.5–2.9 meq g^?1 were prepared. They showed good solubility and high thermal stability up to 300 °C. They showed isotropic membrane swelling in water, which was different from the main‐chain‐type and sulfoalkoxy‐based side‐chain‐type SPIs. The relative humidity (RH) and temperature dependence of proton conductivity were examined. At low RH, the novel SPI membranes showed much higher conductivity than the sulfoalkoxy‐based SPIs. They showed comparable or even higher proton conductivity than Nafion 112 in water at 60 °C (>0.10 S cm^?1). The membrane of NTDA‐DASDSPB/BAPPS (1/1)‐s displayed reasonably high proton conductivities of 0.05 and 0.30 S cm^?1 at 50 and 100% RH, respectively, at 120 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2862–2872, 2006     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Synthesis and properties of polyimide ionomers containing sulfoalkoxy and fluorenyl groups

A series of sulfopropylated and sulfobutylated polyimide copolymers containing fluorenyl groups, SPI‐4, were synthesized to investigate the effect of alkyl side chains on the properties (stability, mechanical strength, water uptake, and proton conductivity) of the polymimide electrolyte membranes. SPI‐4 showed much better hydrolytic stability (in 10% MeOH aq at 100 °C) than the main chain sulfonated polyimide, SPI‐1. Tough, flexible, and ductile membranes were obtained from these copolymers. At high relative humidity all the SPI‐4 membranes showed high mechanical properties (>34 MPa of the maximum stress) and proton conductivity (>0.1 Scm^?1). These properties are comparable to or even better than those of the perfluorosulfonic acid ionomer (Nafion 112). The new polyimide ionomers have proved to be a possible candidate as polymer electrolyte membrane for PEFCs and DMFCs. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4439–4445, 2005     

Sulfonated polybenzimidazoles: Proton conduction and acid–base crosslinking

A series of soluble, benzimidazole‐based polymers containing sulfonic acid groups (SuPBI) has been synthesized. SuPBI membranes resist extensive swelling in water but are poor proton conductors. When blended with high ion exchange capacity (IEC) sulfonated poly(ether ether ketone) (SPEEK), a polymer that has high proton conductivity but poor mechanical integrity, ionic crosslinks form reducing the extent of swelling. The effect of sulfonation of PBI on crosslinking in these blends was gauged through comparison with nonsulfonated analogs. Sulfonic acid groups present in SuPBI compensate for acid groups involved in crosslinking, thereby increasing IEC and proton conductivity of the membrane. When water uptake and proton conductivity were compared to the IEC of blends containing either sulfonated or nonsulfonated PBI, no noticeable distinction between PBI types could be made. Comparisons were also made between these blends and pure SPEEK membranes of similar IEC. Blend membranes exhibit slightly lower maximum proton conductivity than pure SPEEK membranes (60 vs. 75 mS cm^?1) but had significantly enhanced dimensional stability upon immersion in water, especially at elevated temperature (80 °C). Elevated temperature measurements in humid environments show increased proton conductivity of the SuPBI membranes when compared with SPEEK‐only membranes of similar IEC (c.f. 55 for the blend vs. 42 mS cm^?1 for SPEEK at 80 °C, 90% relative humidity). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3640–3650, 2010     

Synthesis of sulfonated aromatic poly(ether amide)s and their application to proton exchange membrane fuel cells

A series of wholly aromatic sulfonated poly(ether amide)s (SPEAs) containing a sulfonic acid group on the dicarbonyl aromatic ring were prepared via a polycondensation reaction of sulfonated terephthalic acid (STA), terephthalic acid (TA), and aromatic diamine monomers. The degree of sulfonation was readily controlled by adjusting the monomer feed ratio of STA and TA in the polymerization process, and randomly sulfonated polymers with an ion exchange capacity (IEC) of 1.0–1.8 mequiv/g were prepared using this protocol. The chemical structures of randomly sulfonated polymers were characterized using NMR and FT‐IR spectroscopies. Gel permeation chromatography analysis of SPEAs indicated the formation of high‐molecular‐weight sulfonated polymer. Tough and flexible SPEA membranes were obtained from solution of N,N‐dimethylacetamide, and thermogravimetric analysis of these membranes showed a high degree of thermal stability. Compared with previously reported sulfonated aromatic polyamides, these new SPEAs showed a significantly lower water uptake of 10–30%. In proton conductivity measurements, ODA‐SPEA‐70 (IEC = 1.80 mequiv/g), which was obtained from polycondensation of 4,4′‐oxydianiline and 70 mol % STA, showed a comparable proton conductivity (105 mS/cm) to that of Nafion 117 at 80 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 485–496, 2009     

Locally sulfonated poly(ether sulfone)s with highly sulfonated units as proton exchange membrane

Novel locally sulfonated poly(ether sulfone)s with highly sulfonated units were successfully synthesized for fuel cell applications. Poly(ether sulfone)s were prepared by the nucleophilic substitution of bis(4‐fluorophenyl) sulfone with 1,2,4,5‐tetrakis([1,1′‐biphenyl]‐2‐oxy)‐3,6‐bis(4‐hydroxyphenoxy)benzene and bis(4‐hydroxyphenyl) sulfide, followed by oxidation using m‐chloroperoxybenzoic acid. The desired highly sulfonated units were easily introduced by postsulfonation and each one had ten sulfonic acid groups. The sulfonated polymers gave tough, flexible, and transparent membranes by solvent casting. The high contrast in polarity between highly sulfonated units and hydrophobic poly(ether sulfone) units enabled the formation of defined phase‐separated structures and well‐connected proton paths. The sulfonated polymers exhibited excellent proton conductivity over a wide range of relative humidities. The proton conductivity of the sulfonated polymer with an ion exchange capacity value of 2.38 mequiv/g was comparable to that of Nafion 117 even at 30% relative humidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3444–3453, 2009     

Nanostructure and properties of sulfonated polyarylenethioethersulfone copolymers as proton exchange fuel cell membranes

A systematic investigation of properties and nanostructure of sulfonated polyarylenethioethersulfone (SPTES) copolymer proton exchange membranes for fuel cell applications has been presented. SPTES copolymers are high temperature resistant (250 °C), and form tough films with excellent proton conductivity up to 170 ± 5 mS/cm (SPTES 70 @ 85 °C, 85%RH). Small angle X‐ray scattering of hydrated SPTES 70 revealed the presence of local water domains (diameter ～5 nm) within the copolymer. The high proton conductivity of the membranes is attributed to the formation of these ionic aggregates containing water molecules, which facilitate proton transfer. AFM studies of SPTES 70 as a function of humidity (25–65%RH) showed an increase in hydrophilic domains with increasing humidity at 22 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2813–2822, 2007     

Investigation of sulfonated poly(ether ether ketone sulfone)/heteropolyacid composite membranes for high temperature fuel cell applications

The sulfonated poly(ether ether ketone sulfone) (SPEEKS)/heteropolyacid (HPA) composite membranes with different HPA content in SPEEKS copolymers matrix with different degree of sulfonation (DS) were investigated for high temperature proton exchange membrane fuel cells. Composite membranes were characterized by Fourier transfer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR band shifts suggested that the sulfonic acid groups on the copolymer backbone strongly interact with HPA particles. SEM pictures showed that the HPA particles were uniformly distributed throughout the SPEEKS membranes matrix and particle sizes decreased with the increment of copolymers' DS. The holes were not found in SPEEKS‐4/HPA30 (consisting of 70% SPEEKS copolymers with DS = 0.8 and 30% HPA) composite membrane after composite membranes were treated with boiling water for 24 h. Thermal stabilities of the composite membranes were better than those of pure sulfonated copolymers membranes. Although the composite membranes possessed lower water uptake, it exhibited higher proton conductivity for SPEEKS‐4/HPA30 especially at high temperature (above 100 °C). Its proton conductivity linearly increased from 0.068 S/cm at 25 °C to 0.095 S/cm at 120 °C, which was higher than 0.06 S/cm of Nafion 117. In contrast, proton conductivity of pure SPEEKS‐4 membrane only increased from 0.062 S/cm at 25 °C to 0.078 S/cm at 80 °C. At 120 °C, proton conductivity decreased to poor 0.073 S/cm. The result indicated that composite membranes exhibited high proton conductivity at high temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1967–1978, 2006     

Synthesis and properties of new fluorinated polymers bearing pendant imidazole groups for fuel cell membranes operating over a broad relative humidity range

New alternating copolymers comprising a chlorotrifluorinated backbone and imidazole‐terminated pendant ethylene oxide groups have been prepared with a view to their use as a component of proton‐conducting membranes in polymer electrolyte fuel cells. A vinyl ether containing an imidazole (Imi) function protected by a benzyl group (BVI) was first synthesized in a three‐step reaction. It was then copolymerized in solution with chlorotrifluoroethylene (CTFE) by conventional radical copolymerization leading to alternating poly(BVI‐alt‐CTFE) copolymers in good yields. Deprotection of the benzyl group under hydrogen produced a chlorotrifluorinated poly(Imi‐alt‐CTFE) copolymer. The polymer was subsequently used to form blend membranes with sulfonated poly(ether ether ketone) (sPEEK). The conductivity of blend membranes of poly (Imi‐alt‐CTFE) with sPEEK lies in the range of 4–10 mS cm^?1 at 40–70 °C and, for blend membranes rich in poly(Imi‐alt‐CTFE), is little dependent on relative humidity between 30 and 100%. It is surmised that the polymer and membrane composition favor microstructural phase separation into chlorotrifluorinated polymer backbone domains and regions in which imidazole groups are clustered. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 223–231, 2010     

Synthesis and properties of sulfonated polyimides derived from bis(sulfophenoxy) benzidines

A series of aromatic sulfonated polyimides (SPIs) bearing sulfophenoxy side groups have been successfully synthesized and evaluated as polymer electrolyte membranes for fuel cell applications. The SPIs had high viscosity and gave tough and flexible membranes. The SPI membranes showed anisotropic membrane swelling in water with much larger dimensional change in thickness direction than in plane one. They showed the better proton‐conducting performance even in the lower relative humidity (RH) range than the other SPI membranes, for example, a high proton conductivity of 0.05 S/cm at 50 % RH and 120 °C. They maintained high mechanical strength and conductivity after aging in water at 130 °C for 500 h, showing much better water stability compared with the main‐chain‐type SPI and side‐chain‐type SPI membranes reported so far. In polymer electrolyte fuel cells (PEFCs) operated at 90 °C and 84–30%RH, they showed fairly high cell performances and have high potential for PEFC applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1463–1477, 2009     

Synthesis and properties of sulfonated polyimides from homologous sulfonated diamines bearing bis(aminophenoxyphenyl)sulfone

Three homologous sulfonated diamines bearing a bis(aminophenoxyphenyl)sulfone structure, namely, bis[4‐(4‐aminophenoxy)phenyl]sulfone‐3,3′‐disulfonic acid (pBAPPS‐3DS), bis[4‐(4‐aminophenoxy)phenyl]sulfone‐2,2′‐disulfonic acid (pBAPPS‐2DS), and bis[4‐(4‐aminophenoxy)‐2‐(3‐sulfobenzoyl)phenyl]sulfone (pBAPPS‐2DSB), were synthesized. A series of sulfonated polyimides (SPIs) were synthesized from 1,4,5,8‐naphthalene tetracarboxylic dianhydride, these sulfonated diamines, and nonsulfonated diamines, and their properties were investigated in comparison with those reported for the SPIs from another homologous diamine or bis[4‐(3‐aminophenoxy)phenyl]sulfone‐3,3′‐disulfonic acid (mBAPPS‐3DS). These SPIs were soluble in common aprotic solvents and showed reasonably high proton conductivity, except for pBAPPS‐2DS‐based SPIs, the conductivity of which was slightly lower because of the lower water uptake. The water stability of these SPIs considerably depended on the structure of the sulfonated diamines and was in the order of pBAPPS‐2DSB ≈ pBAPPS‐2DS > pBAPPS‐3DS ? mBAPPS‐3DS. Their water stability was much lower than that of the SPIs from 4,4′‐bis(4‐aminophenoxy)biphenyl‐3,3′‐disulfonic acid. The reason was discussed on the basis of the basicity of the sulfonated diamine and the solubility property of the SPIs. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2797–2811, 2007     

Sulfonated silica‐based electrolyte nanocomposite membranes

New functionalized particles were prepared by attaching sulfonated aromatic bishydroxy compounds onto fumed silica surface. First, a bromophenyl group was introduced onto the silica surface by reaction of bromophenyltrimethoxysilane with fumed silica. Then, sulfonated bishydroxy aromatic compounds were chemically attached to the silica surface by nucleophilic substitution reactions. The structure of the modified silica was characterized by elemental analysis: ¹³C‐NMR, ²⁹Si‐NMR, and FTIR. Afterward, novel inorganic–organic electrolyte composite membranes based on sulfonated poly(ether ether ketone) have been developed using the sulfonated aromatic bishydroxy compounds chemically attached onto the fumed silica surface. The composite membrane prepared using silica with sulfonated hydroxytelechelic, containing 1,3,4‐oxadiazole units, has higher proton conductivity values in all range of temperatures (40–140 °C) than the membrane containing only the plain electrolyte polymer, while the methanol permeability determined by pervaporation experiment was unchanged. A proton conductivity up to 59 mS cm^?1 at 140 °C was obtained. The combination of these effects may lead to significant improvement in fuel cells (fed with hydrogen or methanol) at temperatures above 100 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2278–2298, 2006     

Crosslinked sulfonated polyimide networks as polymer electrolyte membranes in fuel cells

Sulfonated polyimides with tertiary nitrogen in the polymer backbone were synthesized with 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, 2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane, and diaminoacrydine hemisulfate. They were crosslinked with a series of dibromo alkanes to improve the hydrolytic stability. The crosslinked sulfonated polyimide films were characterized for their thermal stability, ion‐exchange capacity (IEC), water uptake, hydrolytic stability, and proton conductivity. All the sulfonated polyimides had good thermal stability and exhibited a three‐step degradation pattern. With an increase in the alkyl chain length of the crosslinker, IEC decreased as 1.23 > 1.16 > 1.06 > 1.01, and the water uptake decreased as 7.29 > 6.70 > 6.55 > 5.63. The order of the proton conductivity of the crosslinked sulfonated polyimides at 90 °C was as follows: polyimide crosslinked with dibromo butane (0.070) > polyimide crosslinked with dibromo hexane (0.055) > polyimide crosslinked with dibromo decane (0.054). The crosslinked polyimides showed higher hydrolytic stability than the uncrosslinked polyimides. Between the crosslinked polyimides, the hydrolytic stability decreased with an increase in the alkyl chain length of the crosslinker. The crosslinked and uncrosslinked sulfonated polyimides exhibited almost the same proton conductivities. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2370–2379, 2005     

Substituents effect on the properties of sulfonated polyimide copolymers

A series of sulfonated polyimide (SPI) copolymers containing methyl, methoxy, or fluorine groups were synthesized to elucidate the substituents effect on their proton conducting properties as well as thermal, hydrolytic, and oxidative stability for polymer electrolyte membrane fuel cell applications. SPIs of high molecular weight (M_w > 200 kDa, M_n > 80 kDa) along with the ion exchange capacity (IEC) varying between 1.34 and 1.91 mequiv/g were obtained, which gave tough, ductile, and flexible membranes by solution casting. The thermal properties of the SPIs were dominated by the electronic structure of the sulfonated aromatic rings. The electron‐donating methyl groups lowered the thermal decomposition temperature. The hydrolytic and oxidative stability was roughly in the order of IEC (the higher IEC membranes were less stable). Fluorine groups, either as ? F or ? CF₃, had negative effect on the hydrolytic and oxidative stability. In the water uptake and proton conductivity, hydrophobic components are rather more influential than the substituents. It was found out that the SPI(5, 8, 0.7) containing bis(phenoxy)biphenylene sulfone moieties as a rigid hydrophobic component showed the best balanced properties in terms of the stability and the proton conductivity for its rather low IEC. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4469–4478, 2008     

Polymer blend for fuel cells based on SPEKK: Effect of cocontinuous morphology on water sorption and proton conductivity

Proton‐exchange membranes (PEM), suitable for micro and small sized fuel cells, were obtained by blending sulfonated poly(ether ketone ketone) (SPEKK) polymers with different ionic exchange capacity (IEC). This approach was used to limit the amount of swelling caused by water sorption without significantly decreasing the proton conductivity of the membrane. In particular a membrane with a cocontinuous biphasic morphology was obtained by blending two SPEKKs, with respectively, an IEC equal to 1.2 and 2.08 in the weight ratio 60/40, casted from 5% (w/v) solutions in dimethylacetamide. The effect of a cocontinuous morphology on water sorption and proton conductivity in comparison to neat SPEKK was investigated. In the range of temperatures between 40 and 70 °C, which is typical for small and micro fuel cells conditions, it was found that the ratio of proton conductivity to water sorption could be maximized. This has been attributed to the presence of percolative pathways for proton transport provided by the cocontinuous morphology along with the constraint effect of the less sulfonated component on the overall capacity of swelling of the membrane. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 395–404, 2007     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Partially fluorinated sulfonated poly(arylene sulfone)s blended with polybenzimidazole

A partially fluorinated and sulfonated poly(arylene sulfone) (SPSO) was successfully synthesized via nucleophilic polycondensation of 2,2‐bis(4‐fluorophenyl)hexafluoro‐propane with 4,4′‐thiobisbenzenethiol (TBBT). In a second step, the prepared poly(arylene sulfide) was oxidized to SPSO. The polymer was blended with the polybenzimidazole PBIOO^® to obtain a mechanically stable membrane. This film was compared with other polymer blends, which were synthesized in our group in the last years. We were especially interested in the influence of different bridging groups such as ether, ketone, and sulfone groups. The affect on properties such as water uptake (WU), thermal stability, proton conductivity, and oxidative stability were analyzed in this work. Additionally, the blend membranes were characterized by gel permeation chromatography. The novel SPSO blend shows a high molecular weight, and its blend membrane with PBIOO has an excellent onset of ? SO₃H group splitting‐off temperature (T_onset) of 334 °C. The proton conductivity amounts to 0.11 S cm^?1, and the water uptake reaches 30%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011