Poly(arylene thioether)s containing 9,9′‐spirobifluorene moieties in the main chain: Masked dithiol‐based synthesis and excellent optical properties

Poly(arylene thioether)s ( PTEs ) containing 9,9′‐spirobifluorene moieties were synthesized in high yields from 9,9′‐spirobifluorene‐2,2′‐bis(N,N‐dimethylcarbamothioate) 4 as the masked dithiol and various difluoroarenes as electrophilic monomers. All PTEs showed high thermal stability: The 10% weight loss temperature as evaluated by thermogravimetric analysis was over 470 °C under both nitrogen and air atmospheres. The glass transition temperature estimated by DSC was in the range 210–270 °C. The PTEs showed high solubility in ordinary organic solvents, such as CHCl₃, NMP, and THF. Most PTEs exhibited remarkably high refractive indices ranging from 1.69 to 1.73 at 587.6 nm, whereas no or little birefringence was observed for the PTEs . © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4192–4199, 2010     

Fluorene‐rich high performance polyesters: Synthesis and characterization of 9,9‐fluorenylidene and 2,7‐fluorenylene‐based polyesters with excellent optical property

Polyesters PEs containing high content of fluorene units in their backbones were synthesized from 9,9‐diarene‐substituted fluorene diols ( 1 ) and fluorene‐based diacid chlorides ( 2 ) by high temperature polycondensation at 185 °C in diphenyl ether. The molecular weights of the polyesters PE1‐PE5 were in a range of M_w 25,000–165,000. The polyesters displayed their high thermostability: the glass transition temperatures (T_g) by differential scanning calorimetry analysis ranged from 109 to 217 °C, while the 10% weight loss temperatures (T_d10) measured by thermogravimetric analysis were over 400 °C in nitrogen and 395 °C in air. The polyesters had good solubility in most common organic solvents such as chloroform and toluene and gave tough, transparent and flexible cast films. The transmittance of the films was over 80% in the wavelength range from 450 to 700 nm in any PEs . The PEs exhibited high refractive index values around 1.65, while they had very low degree of birefringence. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2549–2556, 2008     

Synthesis and properties of wholly aromatic polymers bearing cardo fluorene moieties

Three series of aromatic polyamides, polyesters, and poly(1,3,4‐oxadiazole)s containing bulky fluorene structures were prepared from 9,9‐bis(4‐carboxyphenyl) fluorene. All of the polymers were readily soluble in many organic solvents and showed useful thermal stability associated with high glass‐transition temperatures in the range of 220–366 °C. These wholly aromatic polymer films were colorless, with high optical transparency, and exhibited UV‐vis absorption bands at 266–348 nm and photoluminescence maximum bands at 368–457 nm within the purple to green region in N,N‐dimethylacetamide (DMAc) solutions. The poly(amine‐amide) Ic exhibited excellent electrochromic contrast and coloration efficiency, changing color from the colorless neutral form to green and then to the dark blue oxidized forms with good stability of electrochromic characteristics. Almost all of these wholly aromatic polymer films were colorless and showed high optical transparency. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4352–4363, 2007     

Ring‐opening metathesis polymerization of new norbornene‐based monomers containing various chromophores

Pure exo‐functional norbornene monomers containing various chromophores such as fluorene, pyrene, and carbazole were successfully prepared via the Diels–Alder reaction and condensation reaction. The living ring‐opening metathesis polymerization (ROMP) of a fluorene‐containing monomer, exo‐2‐(fluorene‐9‐ylcarboxymethyl)norborn‐5‐ene (exo‐1), was observed and confirmed by the formation of a diblock copolymer and a linear relationship between the number‐average molecular weight and [M]/[I] ratios ([M] = monomer concentration; [I] = initiator concentration). The synthesis and characteristics of novel fluorene‐containing polymers based on pure exo‐1 are reported with Grubbs catalyst I {RuCl₂(CHPh)[P(C₆H₁₁)₃]₂} with a high molecular weight of 3.18 × 10⁴ in 90 s ([M]/[I] = 100). However, the ROMP of pyrene‐ and carbazole‐containing monomers [exo‐5‐(pyrene methoxy carbonyl)bicyclo[2.2.1]hept‐2‐ene and exo‐5‐(carbazole ethoxy carbonyl)bicyclo[2.2.1]hept‐2‐ene, respectively] were carried out in a nonliving fashion. All the chromophore‐containing polymers showed excellent solubility in various organic solvents, particularly in chloroform, N‐methyl‐2‐pyrrolidinone, and 1,2‐dichlorobenzene. The glass transition temperatures of polynorbornenes containing various chromophores were determined to be 80–109 °C (by differential scanning calorimetry) higher than that of ring‐opened polynorbornene (glass transition temperature = 35 °C), indicating that the incorporation of the pendant aromatic moieties (e.g., fluorene, pyrene, and carbazole) could enhance the transition temperature for segmental motions of polymer chains. The photoluminescence spectra of all polymer solutions showed a strong emission in the blue region of the visible spectra. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3022–3031, 2007     

Synthesis and characterization of wholly aromatic poly(azomethine)s containing donor–acceptor triphenylamine moieties

N‐(4‐nitrophenyl)‐4′,4″‐bisformyl‐diphenylamine was synthesized from N‐(4‐nitrophenyl)‐diphenylamine by the Vilsmeier‐Haack reaction. Soluble aromatic poly(azomethine)s (PAMs) were prepared by the solution polycondensation of N‐(4‐nitrophenyl)‐4′,4″‐bisformyl‐diphenylamine and aromatic diamine in N‐methyl‐2‐pyrrolidone (NMP) at room temperature under reduced pressure. All the PAMs are highly soluble in various organic solvents, such as N,N‐dimethylacetamide (DMAc), chloroform (CHCl₃), and tetrahydrofuran (THF). Differential scanning calorimetry (DSC) indicated that these PAMs had glass‐transition temperatures (T_gs) in the range of 170–230 °C, and a 10% weight‐loss temperatures in excess of 490 °C with char yield at 800 °C in nitrogen higher than 60%. These PAMs in NMP solution showed UV‐Vis charge‐transfer (CT) absorption at 405–421 nm and photoluminescence peaks around 462–466 nm with fluorescence quantum efficiency (Φ_F) 0.10–0.99%. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of these PAMs can be determined from cyclic voltammograms as 4.86–5.43 and 3.31–3.34 eV, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4921–4932, 2007     

Preparation of carboxyl‐end‐group polyacrylamide with low polydispersity by ATRP initiated with chloroacetic acid

Atom transfer radical polymerization (ATRP) of acrylamide was successfully carried out with chloroacetic acid as initiator and CuCl/N,N,N′,N′‐tetramethylethylenediamine (TMEDA) as catalyst either in water at 80 °C or in glycerol–water (1:1 v/v) medium at 130 °C. In both cases, carboxyl‐end‐group polyacrylamide was obtained with lower polydispersity ranging from 1.03 to 1.44 depending on the polymerization condition. Polymerization kinetics showed that the polymerizations proceeded with a living/controlled nature and accelerated at a higher temperature. The effect of pH in the reaction system on the polymerizations was further studied, revealing that chloroacetic acid not only served as a functional initiator for the ATRP of acrylamde but also provided the acidic polymerization condition, which effectively protected the ATRP of acrylamide from the unexpected complexation and cyclization side‐reactions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3956–3965, 2007     

Synthesis and properties of novel Y‐type nonlinear optical polyimides with high thermal stability of second harmonic generation

2,4‐Bis‐(3,4‐dicarboxyphenylcarboxyethoxy)‐1‐(2,2‐dicyanovinyl)benzene dianhydride (4) was prepared and reacted with 4,4′‐oxydianiline, 4,4′‐diaminobenzanilide and 4,4′‐(hexafluoroisopropylidene)dianiline to yield novel Y‐type polyimides 5‐7 containing 2,4‐dioxybenzylidenemalononitrile groups as nonlinear optical (NLO) chromophores, which constitute parts of the polymer backbone. The resulting polyimides 5‐7 are soluble in polar solvents such as dimethylsulfoxide and N,N‐dimethylformamide. Polymers 5‐7 showed a thermal stability up to 330 °C in thermogravimetric analysis thermograms with T_g values obtained from differential scanning calorimetry thermograms in the range 179–194 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064 nm fundamental wavelength were around 5.56 × 10^?9 esu. The dipole alignment exhibited exceptionally high thermal stability even at 20 °C higher than the glass‐transition temperature there was no SHG decay below 215 °C because of the partial main‐chain character of polymer structure, which is acceptable for NLO device applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3078–3087, 2008     

4‐methoxy‐substituted poly(triphenylamine): A p‐type polymer with highly photoluminescent and reversible oxidative electrochromic characteristics

A 4‐methoxy‐substituted triphenylamine‐containing homopolymer, poly [N,N‐diphenyl‐4‐methoxyphenylamine‐4′,4′′‐diyl] ( PMeOTPA ), with blue light (435 nm) fluorescence quantum efficiency up to 79% was easily prepared by oxidative coupling polymerization of N,N‐diphenyl‐4‐methoxyphenylamine ( MeOTPA ) using FeCl₃ as an oxidant. Its reversible oxidation redox couple was at 0.41 V versus Fc/Fc⁺ in acetonitrile solution. It exhibited good thermal stability with 10% weight‐loss temperatures above 500 °C under a nitrogen atmosphere and relatively high softening temperature (154 °C). The simply designed homopolymer revealed moderate stability of electrochromic characteristics, changing color from original pale yellowish to red, and then to black. The PMeOTPA based field effect transistor also showed p‐type characteristics with significant temperature dependence. The present study suggests that PMeOTPA is a multifunctional polymer for various optoelectronic device applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3292–3302, 2007     

Synthesis and characterization of new soluble poly(amide‐imide)s derived from 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane

A series of new soluble poly(amide‐imide)s were prepared from the diimide‐dicarboxylic acid 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane with various diamines by direct polycondensation in N‐methyl‐2‐pyrrolidinone containing CaCl₂ with triphenyl phosphite and pyridine as condensing agents. All the polymers were obtained in quantitative yields with inherent viscosities of 0.52–0.86 dL · g^?1. The poly(amide‐imide)s showed an amorphous nature and were readily soluble in various solvents, such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide, pyridine, and cyclohexanone. Tough and flexible films were obtained through casting from DMAc solutions. These polymer films had tensile strengths of 71–107 MPa and a tensile modulus range of 1.6–2.7 GPa. The glass‐transition temperatures of the polymers were determined by a differential scanning calorimetry method, and they ranged from 242 to 279 °C. These polymers were fairly stable up to a temperature around or above 400 °C, and they lost 10% of their weight from 480 to 536 °C and 486 to 537 °C in nitrogen and air, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3498–3504, 2001     

Synthesis and properties of polyimides derived from 1,4‐bis(4‐aminophenoxy)‐2‐(6‐oxido‐6H‐dibenz[c,e] [1,2]oxaphosphorin‐6‐yl) phenylene

A new phosphorus‐containing aromatic diamine, 1,4‐bis(4‐aminophenoxy)‐2‐(6‐oxido‐6H‐dibenz[c,e] [1,2]oxaphosphorin‐6‐yl) phenylene ( 3 ) was synthesized by the nucleophilic aromatic substitution of 2‐(6‐oxido‐6H‐dibenz[c,e] [1,2]oxaphosphorin‐6‐yl)‐1,4‐dihydroxy phenylene ( 1 ) with 4‐fluoronitrobenzene, followed by catalytic hydrogenation. Light color, flexible, and creasable polyimides with high molecular weight, high glass transition, high thermal stability, improved organosolubility, and good oxygen plasma resistance were synthesized from the condensation of ( 3 ) with various aromatic dianhydrides in N,N‐dimethylacetamide, followed by thermal imidization. The number‐average molecular weights of polyimides are in the range of 7.0–8.3 × 10⁴ g/mol, and the weight‐average molecular weights are in the range of 12.5–16.5 × 10⁴ g/mol. The T_gs of these polyimides range from 230 to 304 °C by differential scanning calorimetry and from 228 to 305 °C by DMA. These polyimides are tough and flexible, with tensile strength at around 100 MPa. The degradation temperatures (T_d 5%) and char yields at 800 °C in nitrogen range from 544 to 597 °C and 59–65 wt %, respectively. Polyimides 5c and 5e , derived from OPDA and 6FDA, respectively, with the cutoff wavelength of 347 and 342 μm, respectively, show very light color. These polyimides also exhibit good oxygen plasma resistance. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2897–2912, 2007     

Synthesis and properties of highly refractive polyimides derived from fluorene‐bridged sulfur‐containing dianhydrides and diamines

Highly refractive and transparent polyimides (PIs) based on fluorene‐bridged and sulfur‐containing monomers have been developed. An aromatic dianhydride, 4,4′‐[p‐thiobis(phenylenesulfanyl)]diphthalic anhydride (3SDEA), was polymerized with several fluorene‐containing diamines, including commercially available 9,9′‐bis(p‐aminophenyl)fluorene (APF), 9,9′‐bis[4‐(p‐aminophenoxy)phenyl]fluorene (OAPF), and newly synthesized 9,9′‐bis[4‐(p‐aminophenyl)sulfanylphenyl]fluorene (ASPF) to afford series A PIs. Meanwhile, series B PIs were obtained from a new dianhydride, 4,4′‐[(9H‐fluorene‐9‐ylidene)bis(p‐phenylsulfanyl)]diphthalic anhydride (FPSP) and two aromatic diamines, ASPF and 4,4′‐thiobis[(p‐phenylenesulfanyl)aniline] (3SDA) via a two‐step polycondensation procedure. The PIs exhibit good thermal stabilities, such as relatively high glass transition temperatures in the range of 220–270 °C and high initial thermal decomposition temperatures (T_10%) exceeding 490 °C. The 9,9′‐disubstituted fluorene moieties endow the PI films with good optical transparency. The optical transmittances of the PI films at 450 nm are all higher than 80% for the thickness of about 10 μm. Furthermore, the highly aromatic fluorene moiety and flexible thioether linkages in the molecular chains of the PIs provide them with high refractive indices of 1.6951–1.7258 and small birefringence of 0.0056–0.0070. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1510–1520, 2008     

Effects of melt‐processing conditions on the quality of poly(ethylene terephthalate) montmorillonite clay nanocomposites

Organically modified montmorillonite was synthesized with a novel 1,2‐dimethyl‐3‐N‐alkyl imidazolium salt or a typical quaternary ammonium salt as a control. Poly(ethylene terephthalate) montmorillonite clay nanocomposites were compounded via melt‐blending in a corotating mini twin‐screw extruder operating at 285 °C. The nanocomposites were characterized with thermal analysis, X‐ray diffraction, and transmission electron microscopy to determine the extent of intercalation and/or exfoliation present in the system. Nanocomposites produced with N,N‐dimethyl‐N,N‐dioctadecylammonium treated montmorillonite (DMDODA‐MMT), which has a decomposition temperature of 250 °C, were black, brittle, and tarlike resulting from DMDODA degradation under the processing conditions. Nanocomposites compounded with 1,2‐dimethyl‐3‐N‐hexadecyl imidazolium treated MMT, which has a decomposition temperature of 350 °C, showed high levels of dispersion and delamination. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2661–2666, 2002     

Synthesis and characterization of novel hyperbranched polybenzimidazoles based on an AB2 monomer containing four amino groups and one carboxylic group

A new kind of AB₂ monomer, 4‐[2,6‐bis(3,4‐diaminophenyl)pyridin‐4‐yl]benzoic acid, was synthesized, and several hyperbranched polybenzimidazoles (HPBIs) were prepared through self‐polymerization followed by modification reactions with end‐capping reagents such as 4‐methyl benzoic acid and 3‐[3,5‐bis(trifluoromethyl)phenoxy] benzoic acid. The HPBIs had good solubility in strongly aprotic solvents, such as N‐methyl‐2‐pyrrolidone, N,N′‐dimethylformamide, N,N′‐dimethylacetamide, and dimethyl sulfoxide. They also exhibited excellent thermal properties, with glass‐transition temperatures of 318–381 °C and 10% weight loss in the range of 338–674 °C in nitrogen and 329–509 °C in air. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5729–5739, 2006     

Synthesis and properties of thermally stable polyimides bearing pendent fluorene moieties

A new diamine monomer containing fluorene unit, 3,5‐diamino‐N‐(9H‐fluoren‐2‐yl)benzamide was successfully synthesized via the condensation of 2‐aminofluorene and 3,5‐dinitrobenzoyl chloride and subsequent reduction of the dinitro compound. A series of novel aromatic polyimides having pendent fluorenamide moieties were prepared from the reaction of the diamine monomer and various tetracarboxylic dianhydrides by a conventional two‐step polymerization process. The polyimides were obtained in quantitative yields with inherent viscosities of 0.33–0.44 dl/g. The resulting polymers dissolved in N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide. The glass transition temperature of these polymers was in the range of 261–289°C. They were fairly stable up to a temperature around 450°C and lost 10% weight in the range of 498–556°C in nitrogen. The UV–vis absorption spectra showed that all of the polymers had absorption maxima around 320 nm. Cyclic voltammograms of the polyimides revealed an oxidation wave with a peak around 1.3 V. Copyright © 2014 John Wiley & Sons, Ltd.     

Measuring structural inhomogeneity of a helical conjugated polymer at high pressure and temperature

We report on X‐ray scattering measurements of helical poly[9,9‐bis(2‐ethylhexyl)‐fluorene‐2,7‐diyl] by mapping the sample with 10 μm spatial resolution from 0.3 GPa to 36 GPa. We follow the strongest 00l reflection, which moves toward higher scattering angles with pressure indicating planarization of helical polyfluorene. Lateral inhomogeneity is increased for >10 GPa concomitant with the solidification of the pressure transmitting medium (a 4:1 mixture of methanol and ethanol). We also follow the 00l reflection with increasing temperature at the constant pressure of 4.3 GPa in neon. We observe a sharp shift toward higher scattering angles indicative of a phase transition at 167–176 °C. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 392–396     

Synthesis and properties of fluorine‐containing poly(aryl ether oxadiazole)s

Fluorine‐containing poly(aryl ether 1,3,4‐ozadiazole)s were synthesized by the nucleophilic aromatic substitution reaction of 2,5‐bis(2,3,4,5,6‐pentafluorophenyl)‐1,3,4‐oxadiazole and various bisphenols in the presence of potassium carbonate. The polymerizations were carried out at 30 °C in 1‐methyl‐2‐pyrrolidinone to avoid the gelation caused by a crosslinking reaction at para and ortho carbons to the 1,3,4‐oxidiazole ring. The obtained polymers were all para‐connected linear structures. The obtained fluorine‐containing poly(aryl ether 1,3,4‐ozadiazole)s showed excellent solubility and afforded tough, transparent films by the solution‐casting method. They also exhibited a high glass transition temperature depending on the molecular structure, and the glass transition temperature could be controlled by the bisphenols in the range of 157–257 °C. They showed good thermal stability and excellent hydrophobicity due to the incorporation of the 2,3,5,6‐tetrafluoro‐1,4‐phenylene moiety. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2855–2866, 2007     

Synthesis and properties of new fluorene‐based polyquinoxalines with an ether linkage in the main chain for light‐emitting diodes

A new series of fluorene‐based polyquinoxalines with an ether linkage in the main chain were prepared by the polycondensation reaction between a tetraketone monomer and 3,3′,4,4′‐tetraaminodiphenyl ether. The polycondensation was usually carried out in m‐cresol. The resulting polymers ( P1 – P3 ) [ P1 = poly(quinoxaline‐co‐9,9‐dihexyl‐2,7‐dimethyl‐9H‐fluorene) P2 = poly(quioxaline‐co‐9,9‐dihexyl‐9‐pentyl‐2,7‐di‐p‐tolyl‐9H‐fluorene) P3 = poly(quioxaline‐co‐9,9‐bis‐(4‐methoxy‐phenyl)‐2,7‐dimethyl‐9H‐fluorene)] showed good solubility in common organic solvents and high thermal stability with only a 5% weight loss up to 440 °C. P1 and P2 had very high glass‐transition temperatures of 212 and 223 °C, respectively, whereas P3 did not show any phase‐transition temperature in repeated scans up to 300 °C. All the polymers in photoluminescence showed blue emissions in the range of 432–465 nm, both in chloroform solutions and in thin films. Light‐emitting diode devices of the configuration indium tin oxide/poly(3,4‐ethylenedioxythiophene)/polymer:poly(N‐vinylcarbazole) blend (2:8)/LiF/Al were fabricated with P1 or P2 and emitted blue light with electroluminescence peak wavelengths of 434 and 448 nm, respectively. The maximum brightness and the external quantum efficiency of P1 were 0.56 μW/cm² at 29 V and 0.056%, whereas P2 showed 0.50 μW/cm² at 34 V and a relatively low value of 0.015%, respectively. Cyclic voltammetry studies revealed that these polymers possessed low‐lying ionization potential energy levels ranging from ?5.49 to ?5.86 eV and low‐lying electron affinity energy levels ranging from ?2.65 to ?2.88 eV. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1189–1198, 2006     

Soluble and transparent polyimides with high Tg from a new diamine containing tert‐butyl and fluorene units

A novel diamine monomer 1 , 4,4'‐(9H‐fluorene‐9,9‐diyl)‐bis(2‐tert‐butylaniline), was synthesized from 9‐fluorenone and 2‐tert‐butylaniline by the condensation reaction. Then it was polymerized with several commercial aromatic dianhydrides, respectively, to produce polyimides (PIs) by the one‐pot method. The number‐averaged molecular weights of the resulting PIs are in the range of (4.54–8.82) × 10⁴ with polydispersity indices from 2.51 to 4.33 by gel permeation chromatography measurement. They are soluble in many organic solvents and can form transparent and tough films by solution‐casting. The cut‐off wavelengths of UV–vis absorption for the PI films are below 360 nm, which are much lower than that of Kapton film. The light transparency of them is above 90% in the visible light range from 400 to 760 nm. They also display relatively low dielectric constants (from 2.79 to 3.00), low water absorption rates (<1%), and high tensile strength (> 50 MPa). Their excellent solubility and transparency can be attributed to the incorporation of tert‐butyl groups and fluorene units into the rigid backbones of PIs. Simultaneously, they still maintain the high thermal stability (the 5% weight loss temperature in the range from 526 to 539 °C in nitrogen) and the high glass transition temperatures (T_g > 340 °C). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 976–984     

Synthesis and characterization of novel soluble triphenylamine‐containing aromatic polyamides based on N,N′‐bis(4‐aminophenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine, N, N′‐bis(4‐aminophenyl)‐N, N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 4‐fluoronitrobenzene, followed by catalytic reduction. A series of novel aromatic polyamides with triphenylamine units were prepared from the diamine and various aromatic dicarboxylic acids or their diacid chlorides via the direct phosphorylation polycondensation or low‐temperature solution polycondensation. All the polyamides were amorphous and readily soluble in many organic solvents such as N, N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with relatively high glass‐transition temperatures (257–287 °C), 10% weight‐loss temperatures in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 72%. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2810–2818, 2002     

Preparation and properties of imide‐containing elastic polymers from elastic polyureas and pyromellitic dianhydride

A new approach to obtain imide‐containing elastic polymers (IEPs) via elastic and high‐molecular‐weight polyureas, which were prepared from α‐(4‐aminobenzoyl)‐ω‐[(4‐aminobenzoyl)oxy]‐poly(oxytetramethylene) and the conventional diisocyanates such as tolylene‐2,4‐diisocyanate(2,4‐TDI), tolylene‐2,6‐diisocyanate(2,6‐TDI), and 4,4′‐diphenylmethanediisocyanate (MDI), was investigated. IEP solutions were prepared in high yield by the reaction of the polyureas with pyromellitic dianhydride in N‐methyl‐2‐pyrrolidone (NMP) at 165°C for 3.7–5.2 h. IEPs were obtained by the thermal treatment at 200°C for 4 h in vacuo after NMP was evaporated from the resulting IEP solutions. We assumed a mechanism of the reaction via N‐acylurea from the identification of imide linkage and amid acid group in IEP solutions. NMR and FTIR analyses confirmed that IEPs were segmented polymers composed of imide hard segment and poly(tetramethylene oxide) (PTMO) soft segment. The dynamic mechanical and thermal analyses indicated that the IEPs prepared from 2,6‐TDI and MDI showed a glass‐transition temperature (T_g ) at about −60°C, corresponding to T_g of PTMO segment, and suggested that microphase‐separation between the imide segment and the PTMO segment occured in them. TGA studies indicated the 10% weight‐loss temperatures (T₁₀) under air for IEPs were in the temperature range of 343–374°C. IEPs prepared from 2,6‐TDI and MDI showed excellent tensile properties and good solvent resistance. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 715–723, 2000