A New Voltammetric Sensor for Hydrazine Based on Michael Addition Reaction Using 1‐Amino‐2‐naphtol‐4‐sulfonic Acid

In this paper, voltammetric determination of hydrazine was investigated by 1‐amino‐2‐naphtol‐4‐sulfonic acid (ANSA) at the surface of carbon paste electrode (CPE) using cyclic voltammetry (CV) and double potential step chronoamperometry. Results showed that in pH 7.00, hydrazine participates in Michael addition reaction with ANSA and the anodic peak potential of hydrazine shifted to 726 mV less positive than CPE in absence of ANSA, this value is unique compared with other research works. Also, the value of rate constant for the oxidation of hydrazine was calculated 8.3 × 10⁴ cm³ mol^‐1 s^‐1 and the diffusion coefficient of ANSA at the surface of CPE was determined 7.3 × 10^‐7 cm² s^‐1. A linear correlation between Ip and hydrazine concentration in the ranges, from 5 × 10^‐5 mol/L to 2.5 × 10^‐2 mol/L with CV method was obtained and the detection limit was found as 4.3 × 10^‐5 mol/L.     

Study on the Electrochemical Behavior of Dopamine and Uric Acid at a 2‐Amino‐5‐mercapto‐[1,3,4] Triazole Self‐Assembled Monolayers Electrode

Selected from a series of structurally related heteroaromatic thiols, a newly synthesized reagent 2‐amino‐5‐mercapto‐[1,3,4] triazole (MATZ) was used to fabricate self‐assembled monolayers (SAMs) on gold electrode for the first time. The MATZ/Au SAMs was characterized by electrochemical methods and scanning electronic microscopy (SEM). In 0.04 mol/L Britton–Robinson buffer solution (pH 5), the electrochemical behavior of dopamine showed a quasireversible process at the MATZ/Au SAMs with an electrode kinetic constant 0.1049 cm/s. However, the electrochemical reaction of uric acid at the SAMs electrode showed an irreversible oxidation process, the charge‐transfer kinetics of uric acid was promoted by the SAMs. By Osteryoung square‐wave voltammetry (OSWV), the simultaneous determination of dopamine and uric acid can be accomplished with an oxidation peak separation of 0.24 V, the peak current of dopamine and uric acid were linearly to its concentration in the range of 2.5×10^?6–5.0×10^?4 mol/L for dopamine and 1×10^?6–1×10^?4 mol/L for uric acid with a detection limit of 8.0×10^?7 mol/L for dopamine and 7.0×10^?7 mol/L for uric acid. The MATZ/Au SAMs electrode was used to detect the content of uric acid in real urine and serum sample with satisfactory results.     

Alternating copolymers of 2,6‐bis(p‐dihexylaminostyryl)anthracene‐9,10‐diyl and N‐octylcarbazole with large two‐photon cross sections

We report the synthesis, thermal, one‐ and two‐photon properties of poly(2,6‐bis(p‐dihexylaminostyryl)anthracene‐9,10‐diyl‐alt‐N‐octylcarbazole‐3,6‐/2,7‐diyl) ( P1/P2 ). The as‐synthesized polymers exhibit number‐average molecular weights of 1.7 × 10⁴ for P1 and 2.1 × 10⁴ g/mol for P2 . They emit strong one‐ and two‐photon excitation fluorescence with the peak around 502 nm, and the fluorescence quantum yields around 0.76 in chloroform. In film state, P1 and P2 show different red‐shift emission with the peaks at 512 nm and 523 nm, respectively. The DSC measurement reveals that as‐synthesized polymers are all amorphous aggregates with the glass transition temperatures of 131 °C for P1 and 152 °C for P2 . The solution two‐photon absorption (TPA) properties of P1 and P2 in chloroform are measured by the two‐photon‐induced fluorescence method using femtosecond laser pulses (120 fs). The TPA cross sections (δ) are measured over the range of 700–900 nm. The maximal δ of P1 and P2 all appear at ～800 nm and are 1010 GM and 940 GM per repeating unit, respectively. This suggests that no notable interactions among structure units that impair their fluorescence and TPA properties, and the polymers with large δ can be obtained by using the high TPA‐active units as building blocks. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and two‐photon absorption properties of hyperbranched diketo‐pyrrolo‐pyrrole polymer with triphenylamine as the core

A novel hyperbranched polyyne (hb‐ DPP ) with triphenylamine as the core, 2,5‐dioctylpyrrolo [3,4‐c]pyrrole‐1,4 (2H,5H)‐dione ( DPP ) as the connecting unit has been designed and synthesized by Glaser‐Hay oxidative coupling reaction, which was characterized by IR, NMR, UV‐vis, FL, and GPC. The polymer exhibits high molecular weight (M_w up to ～6.55 × 10⁴ Da) and is readily soluble in common organic solvents such as toluene, chloroform, tetrahydrofuran, N,N‐dimethyl formamide and so on. The one‐ and two‐photon absorption (TPA) properties have been investigated. The TPA cross section of the polymer was measured by open‐aperture Z‐scan experiment using 140 femtosecond (fs) pulse, and the TPA cross section for hb‐ DPP was determined to be 579 GM per repeating unit at wavelength of 800 nm. In tetrahydrofuran, hb‐ DPP exhibits intense frequency up‐converted fluorescence with the peak located at 584 nm under the excitation of 800 nm fs pulses. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4400–4408, 2009     

Sol—Gel Derived Carbon Ceramic Electrode Bulk—Modified with Tris（1,10—phenanthroline—5,6—dione） iron （Ⅱ）Hexafluorophosphate and Its Use as an Amperometric Iodate Sensor

A surface‐renewable tris(1, 10‐phenanthroline‐5, 6‐dione) iron (D) hexafluorophosphate (FePD) modified carbon ceramic electrode was constructed by dispersing FePD and graphite powder in methyltrimethoxysilane (MTMOS) based gels. The FePD‐modified electrode presented pH‐dependent voltammetric behavior, and its peak currents were diffusion‐controlled in 0.1 mol/L Na₂SO₄ + H₂SO₄ solution (pH = 0.4). In the presence of iodate, dear electrocatalytic reduction waves were observed and thus the chemically modified electrode was used as an amperometric sensor for iodate in common salt. The linear range, sensitivity, detection limit and response time of the iodate sensor were 5 × 10^?6–1 × 10^?2 mol/L, 7.448 μA·L/ mmol, 1.2 × 10^?6 mol/L and 5 s, respectively. A distinct advantage of this sensor is its good reproducibility of surface‐renewal by simple mechanical polishing.     

Application of a Modified CuO Nanoparticles Carbon Paste Electrode for Simultaneous Determination of Isoperenaline,Acetaminophen and N‐acetyl‐L‐cysteine

A 1‐[2‐hydroxynaphthylazo]‐6‐nitro‐2‐naphthol‐4‐sulfonate/ CuO nanoparticles modified carbon paste electrode (HNNSCCPE) was constructed and the electro‐oxidation of isoprenaline at the surface of the modified electrode was studied using cyclic voltammetry (CV), chronoamperometry (CHA), and square wave voltammetry (SWV). Under the optimized conditions, the square wave voltammetric peak current of isoprenaline increased linearly with isoprenaline concentrations in the range of 1.0×10^?7 to 7.0×10^?4 M and detection limit of 5.0×10^?8 M was obtained for isoprenaline. The prepared modified electrode exhibits a very good resolution between the voltammetric peaks of isoprenaline, acetaminophen and N‐acetyl‐L‐cysteine which makes it suitable for the detection of isoprenaline in the presence of acetaminophen and N‐acetyl‐L‐cysteine in real samples.     

Assessing the detectability of antioxidants in two‐dimensional high‐performance liquid chromatography

This paper explores the analytical figures of merit of two‐dimensional high‐performance liquid chromatography for the separation of antioxidant standards. The cumulative two‐dimensional high‐performance liquid chromatography peak area was calculated for 11 antioxidants by two different methods—the areas reported by the control software and by fitting the data with a Gaussian model; these methods were evaluated for precision and sensitivity. Both methods demonstrated excellent precision in regards to retention time in the second dimension (%RSD below 1.16%) and cumulative second dimension peak area (%RSD below 3.73% from the instrument software and 5.87% for the Gaussian method). Combining areas reported by the high‐performance liquid chromatographic control software displayed superior limits of detection, in the order of 1 × 10^?6 M, almost an order of magnitude lower than the Gaussian method for some analytes. The introduction of the countergradient eliminated the strong solvent mismatch between dimensions, leading to a much improved peak shape and better detection limits for quantification.     

Electrochemical Characterization of Gold 6‐Amino‐2‐mercaptobenzothiazole Self‐Assembled Monolayer for Dopamine Detection in Pharmaceutical Samples

A new sensor, gold‐6‐amino‐2‐mercaptobenzothiazole (6A2MBT), was fabricated via a self‐assembly procedure. Electrochemical properties of the monolayer were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The modified electrode showed excellent antifouling property against the oxidation products of DA, allowed us to construct a dynamic calibration curve with two linear parts, 1.00×10^?6 to 3.72×10^?4 and 3.72×10^?4 to 6.42×10^?4 M DA, with correlation coefficients of 0.997 and 0.992 and a detection limit of 1.57×10^?7 M DA by using differential pulse voltammetry (DPV), respectively. Finally, the performance of the Au‐6A2MBT modified electrode was successfully tested for electrochemical detection of DA in a pharmaceutical sample.     

High‐quality poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] synthesized by a solid–liquid two‐phase reaction: Characterizations and electroluminescence properties

Poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] (MEH‐PPV) with a molar mass of 26–47 × 10⁴ g mol^?1 and a polydispersity of 2.5–3.2 was synthesized by a liquid–solid two‐phase reaction. The liquid phase was tetrahydrofuran (THF) containing 1,4‐bis(chloromethyl)‐2‐methoxy‐5‐(2′‐ethylhexyloxy)benzene as the monomer and a certain amount of tetrabutylammonium bromide as a phase‐transfer catalyst. The solid phase consisted of potassium hydroxide particles with diameters smaller than 0.5 mm. The reaction was carried out at a low temperature of 0 °C and under nitrogen protection. No gelation was observed during the polymerization process, and the polymer was soluble in the usual organic solvents, such as chloroform, toluene, THF, and xylene. A polymer light‐emitting diode was fabricated with MEH‐PPV as an active luminescent layer. The device had an indium tin oxide/poly(3,4‐ethylenedioxylthiophene) (PEDOT)/MEH‐PPV/Ba/Al configuration. It showed a turn‐on voltage of 3.3 V, a luminescence intensity at 6.1 V of 550 cd/m², a luminescence efficiency of 0.43 cd/A, and a quantum efficiency of 0.57%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3049–3054, 2004     

Characterization of two‐ and three‐photon absorption of polyfluorene derivatives

Fluorene‐based polymer derivatives are promising materials for organic electronic devices because of their photoluminescence and electroluminescence, good film‐forming ability, and favorable chemical and thermal properties. Although optical properties of polyfluorene have already been reported, most of the studies focused on the linear optical properties, whereas nonlinear optical characteristics have only recently received more detailed attention. Here, we report on two polyfluorene derivatives, poly(9,9′‐n‐dihexyl‐2,7‐fluorenediyl) (LaPPS 10) and poly(9,9′‐n‐dihexyl‐2,7‐fluorene‐diyl‐vinylene) (LaPPS 38), which present intense nonlinear absorption and fluorescence. Two‐photon absorption cross‐section properties of both polymers were characterized in the spectral range from 500 nm up to 900 nm, reaching peak values around 2000 Göppert Mayer units. Optical limiting behavior and two‐photon‐induced fluorescence of both polymers have also been investigated. Furthermore, the first molecular hyperpolarizability of the polymers was also studied using hyper‐Rayleigh scattering. In addition, the three‐photon absorption (3PA) spectra of both materials were also investigated, and 3PA cross‐section values in the order of 1 × 10^?78 cm⁶ s² photon^?2 were observed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 747–754     

A Highly Selective and Sensitive Barium(II)‐Selective PVC Membrane Based on Dimethyl 1‐Acetyl‐8‐oxo‐2,8‐dihydro‐ 1H‐pyra‐zolo[5,1‐a]isoindole‐2,3‐dicarboxylate

A poly(vinyl chloride)‐based membrane of dimethyl 1‐acetyl‐8‐oxo‐2,8‐dihydro‐1H‐pyra‐zolo[5,1‐a]isoindole‐2,3‐dicarboxylate as a neutral carrier with sodium tetraphenylborate (NaTPB) as an anion excluder and 2‐nitrophenyl octyl ether (NPOE) as plasticizer was prepared and investigated as a Ba(II)‐selective electrode. The electrode exhibits a Nernstian slope of 29.7±0.4 mV per decade over a wide concentration range (1.0×10^?6 to 1.0×10^?1 M) with a detection limit of 7.6×10^?7 M between pH 3.0 and 11.0. The response time of the sensor is about 10 s and it can be used over a period of 2 months without any divergence in potential. The proposed membrane sensor revealed good selectivity for Ba(II) over a wide variety of other metal ions. It was successfully used in direct determination of barium ions in industrial wastewater samples.     

Synthesis,one‐ and two‐photon properties of poly[9,10‐bis(3,4‐bis(2‐ethylhexyl‐oxy)phenyl)‐2,6‐anthracenevinylene‐alt‐N‐octyl‐3,6‐/2,7‐carbazolevinylene]

The synthesis, one‐ and two‐photon absorption (TPA) and emission properties of two novel 2,6‐anthracenevinylene‐based copolymers, poly[9,10‐bis(3,4‐bis(2‐ethylhexyloxy)phenyl)‐2,6‐anthracenevinylene‐alt‐N‐octyl‐3,6‐carbazolevinyl‐ene] ( P1 ) and poly[9,10‐bis(3,4‐bis(2‐ethylhexyloxy)phenyl)‐2,6‐anthracenevinyl‐ene‐alt‐N‐octyl‐2,7‐carbazolevinylene] ( P2 ) were reported. The as‐synthesized polymers have the number‐average molecular weights of 1.56 × 10⁴ for P1 and 1.85 × 10⁴ g mol^?1 for P2 and are readily soluble in common organic solvents. They emit strong bluish‐green one‐ and two‐photon excitation fluorescence in dilute toluene solution (? _P1 = 0.85, ? _P2 = 0.78, λ_em( P1 ) = 491 nm, λ_em( P2 ) = 483 nm). The maximal TPA cross‐sections of P1 and P2 measured by the two‐photon‐induced fluorescence method using femtosecond laser pulses in toluene are 840 and 490 GM per repeating unit, respectively, which are obviously larger than that (210 GM) of poly[9,10‐bis‐(3,4‐bis(2‐ethylhexyloxy) phenyl)‐2,6‐anthracenevinylene], indicating that the poly(2,6‐anthracenevinylene) derivatives with large TPA cross‐sections can be obtained by inserting electron‐donating moieties into the polymer backbone. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 463–470, 2010     

Electrochemical Study of s‐Triazine Herbicides Transfer Across the Water/1,2‐Dichloroethane Interface

The transfer of three s‐triazine herbicides, atrazine (ATR), propazine (PRO) and prometrine (PROM), across the water/1,2‐dichloroethane interface was investigated using cyclic voltammetry. A facilitated proton transfer mechanism from the aqueous to organic phase is demonstrated by the analysis of positive peak potential and peak current as a function of pH. It is shown that the determination of 2.5×10^?5 M – 5×10^?4 M concentration of herbicides in aqueous phase may be possible under the experimental conditions employed.     

Electrochemical Behaviors of Adenosine‐5′‐triphosphate on Molecular Wire Modified Carbon Paste Electrode and Its Sensitive Detection

A new electrochemical method was proposed for the determination of adenosine‐5′‐triphosphate (ATP) based on the electrooxidation at a molecular wire (MW) modified carbon paste electrode (CPE), which was fabricated with diphenylacetylene (DPA) as the binder. A single well‐defined irreversible oxidation peak of ATP appeared on MW‐CPE with adsorption‐controlled process and enhanced electrochemical response in a pH 3.0 Britton‐Robinson buffer solution, which was due to the presence of high conductive DPA in the electrode. The electrochemical parameters of ATP were calculated with the electron transfer coefficient (α) as 0.54, the electron transfer number (n) as 1.9, the apparent heterogeneous electron transfer rate constant (k_s) as 2.67 × 10^?5 s^?1 and the surface coverage (Γ_T) as 4.15 × 10^?10 mol cm^?2. Under the selected conditions the oxidation peak current was proportional to ATP concentration in the range from 1.0 × 10^?7 mol L^?1 to 2.0 × 10^?3 mol L^?1 with the detection limit as 1.28 × 10^?8 mol L^?1 (3σ) by sensitive differential pulse voltammetry. The proposed method showed good selectivity without the interferences of coexisting substances and was successful applied to the ATP injection samples detection.     

Electrochemical Determination of 2‐Nitrophenol in Water Samples Using Mg‐Al‐SDS Hydrotalcite‐Like Clay Modified Glassy Carbon Electrode

A glassy carbon electrode (GCE) modified with Mg‐Al‐SDS hydrotalcite‐like clay (SDS‐HTLC) was used for the sensitive voltammetric determination of 2‐nitrophenol (2‐NP) utilizing the oxidation process. The results indicate the prepared modified electrode has an excellent electrocatalytic activity toward 2‐NP oxidation, lowering the oxidation overpotential and increasing the oxidation current. Under optimal conditions, the oxidation current was proportional to 2‐NP concentration in the range from 1.0×10^?6 to 6.0×10^?4 M with the detection limit of 5.0×10^?7 M by DPV (S/N=3). The fabricated electrode was applied for 2‐NP determination in water samples and the recovery for these samples was from 95.6 to 103.5%.     

Voltammetric Determination of 3‐Nitrofluoranthene and 3‐Aminofluoranthene at Boron Doped Diamond Thin‐Film Electrode

The voltammetric behavior of 3‐nitrofluoranthene and 3‐aminofluoranthene was investigated in mixed methanol‐water solutions by differential pulse voltammetry (DPV) at boron doped diamond thin‐film electrode (BDDE). Optimum conditions have been found for determination of 3‐nitrofluoranthene in the concentration range of 2×10^?8–1×10^?6 mol L^?1, and for determination 3‐aminofluorathnene in the concentration range of 2×10^?7–1×10^?5 mol L^?1, respectively. Limits of determination were 3×10^?8 mol L^?1 (3‐nitrofluoranthene) and 2×10^?7 mol L^?1 (3‐aminofluoranthene).     

Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

A sensitive and selective sensor‐coated molecularly imprinted sol–gel film incorporating β‐cyclodextrin‐multi‐walled carbon nanotubes and cobalt nanoparticles‐chitosan for oxacillin determination

A sensitive and selective imprinted electrochemical sensor for the determination of oxacillin was developed based on indium tin oxide electrode. The proposed sensor was decorated with imprinted sol–gel film and cobalt nanoparticles‐chitosan/β‐cyclodextrin‐multiwalled carbon nanotubes nanocomposites. The surface morphologies of the modified electrodes were characterized by scanning electron microscopy and transmission electron microscope. The stepwise assembly process and electrochemical behavior of the novel sensor were characterized by differential pulse voltammetry, cyclic voltammetry and Amperometric i‐t response. The imprinted sensor displayed excellent selectivity toward oxacillin. Meanwhile, the introduced cobalt nanoparticles‐chitosan and β‐cyclodextrin‐multi‐walled carbon nanotubes exhibited noticeable amplified electrochemical response signal. The differential voltammetric anodic peak current was linear to oxacillin concentration in the range from 2.0 × 10^?7 to 1.0 × 10^?4 mol·l^?1, and the detection limit was 6.9 × 10^?9 mol·l^?1. The proposed imprinted sensor was applied to the determination of oxacillin in human blood serum samples successfully. Copyright © 2011 John Wiley & Sons, Ltd.     

Electrocatalytic Reduction and Determination of Iodate and Periodate at Silicomolybdate‐Incorporated‐Glutaraldehyde‐ Cross‐Linked Poly‐L‐lysine Film Electrodes

The present work describes reduction of iodate (IO₃^?), and periodate (IO₄^?) at silicomolybdate‐doped‐glutaraldehyde‐cross‐linked poly‐L ‐lysine (PLL‐GA‐SiMo) film coated glassy carbon electrode in 0.1 M H₂SO₄. In our previous study, we were able to prepare the PLL‐GA‐SiMo film modified electrode by means of electrostatically trapping SiMo₁₂O₄₀^4? mediator in the cationic film of PLL‐GA, and the voltammetric investigation in pure supporting indicated that the charge transport through the film was fast. Here, the electrocatalytic activity of PLL‐GA‐SiMo film electrode towards iodate and periodate was tested and subsequently used for analytical determination of these analytes by amperometry. The two electron reduced species of SiMo₁₂O₄₀^4? anion was responsible for the electrocatalytic reduction of IO₃^? at PLL‐GA‐SiMo film electrode while two and six electron reduced species were showed electrocatalytic activity towards IO₄^? reduction. Under optimized experimental conditions of amperometry, the linear concentration range and sensitivity are 2.5×10^?6 to 1.1×10^?2 M and 18.47 μA mM^?1 for iodate, and 5×10^?6 to 1.43×10^?4 M and 1014.7 μA mM^?1 for periodate, respectively.     

Fabrication of Nanocomposite Containing Naphthoquinone and Nanogold Supported on Poly(2,6‐pyridinedicarboxylic acid) Film for Voltammetric Determination of N‐Acetyl‐L‐Cysteine

A modified electrode was fabricated by grafting of poly (2,6‐pyridinedicarboxylic acid) film (PDC) by electropolymerization of 2,6‐pyridinedicarboxylic acid on the glassy carbon electrode (GCE). Then, gold nanoparticles (NG) and 1,2‐naphthoquinone‐4‐sulfonic acid sodium (Nq) were immobilized on the PDC/GCE to prepare Nq/NG/PDC/GCE by immersing electrode into NG and Nq solution, respectively. The Nq species on NG/PDC/GCE could catalyze electrooxidation of N‐acetyl‐L ‐cysteine (NAC) with lowering the over potential by about 600 mV. This method used for detection of NAC in dynamic range from 4.0×10^?6 M to 1.30×10^?4 M with a detection of limit (2σ) 8.0×10^?7 M.