Effect of different matrices and nanofillers on the rheological behavior of polymer‐clay nanocomposites

In this work, a comprehensive study of the rheological behavior under shear and isothermal and nonisothermal elongational flow of low density polyethylene (LDPE) and ethylene‐vinyl acetate copolymer (EVA) based nanocomposites was reported to evaluate their “filmability”, that is, the ability of these material to be processed for film forming applications. The influence of two different kinds of organoclay – namely Cloisite 15A and Cloisite 30B – and their concentration was evaluated. The presence of filler clearly affects the rheological behavior in oscillatory state of polyolefin‐based nanocomposites but the increase of complex viscosity and the shear thinning are not dramatic. A larger strain‐hardening effect in isothermal elongational flow is shown by the nanocomposites compared to that of the pure matrix, particularly for EVA based nanocomposites. The melt strength measured under nonisothermal elongational flow increases in the presence of the nanofiller, while the drawability is only slightly lower than that measured for the neat matrix. Moreover, the rheological behavior under nonisothermal elongational flow of EVA‐based nanocomposites is similar for both nanoclays used. Differently, LDPE‐based nanocomposites show a strong dependence on the type of organoclay. Finally, the mechanical properties of the materials were measured by tensile tests. They revealed that the presence of the filler provokes, in all the cases, an increase of the rigidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 344–355, 2010     

Effect of EVM/EVA‐g‐MAH ratio on the structure and properties of nylon 1010 blends

The nylon 1010/ethylene‐vinyl acetate rubber (EVM)/maleated ethylene‐vinyl acetate copolymers (EVA‐g‐MAH) ternary blends were prepared. The effect of EVM/EVA‐g‐MAH ratio on the toughness of blends was examined. A super tough nylon 1010 blends were obtained by the incorporation of both EVM and EVA‐g‐MAH. Impact essential work of fracture (EWF) model was used to characterize the fracture behavior of the blends. The nylon/EVM/EVA‐g‐MAH (80/15/5) blend had the highest total fracture energy at a given ligament length (5 mm) and the highest dissipative energy density among all the studied blends. Scanning electron microscopy images showed the EVM and EVA‐g‐MAH existed as spherical particles in nylon 1010 matrix and their size decreased gradually with increasing EVA‐g‐MAH content. Large plastic deformation was observed on the impact fracture surface of the nylon/EVM/EVA‐g‐MAH (80/15/5) blend and related to its high impact strength. Then with increasing EVA‐g‐MAH proportion, the matrix shear yielding of nylon/EVM/EVA‐g‐MAH blends became less obvious. EVM and EVA‐g‐MAH greatly increased the apparent viscosity of nylon 1010, especially at low shear rates. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 877–887, 2009     

Grafting of polycaprolactone onto poly(ethylene‐co‐vinyl alcohol) and application to polyethylene‐based bioerodable blends

Poly(ethylene‐co‐vinyl acetate) (EVA) powders containing 10 and 20 wt % of vinyl acetate (VAc) units was saponified in ethanol/KOH solution in a heterogeneous manner. Intermolecular interaction between vinyl alcohol(VOH) units in the produced poly(ethylene‐co‐vinyl alcohol) (EVOH) promoted the crystallization of intervening segments composed of ethylene units. Ring opening polymerization of caprolactone (CL) in the presence of EVOH gave EVOH‐g‐PCL graft copolymers with relatively short chain branches. Even though the graft copolymerization was carried out in a homogeneous solution, all the VOH units were not equally reactive for the PCL grafting. And the unreacted VOH units decreased very slowly with the graft copolymerization time. EVOH‐g‐PCL decreased the domain size of the dispersed phase in low density polyethylene (PE)/biodegradable master batch (MB) blends, and thus increased their tensile properties significantly. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2561–2569, 2002     

Thermal analysis and FT‐IR studies of adsorbed poly(ethylene‐stat‐vinyl acetate) on silica

Adsorbed poly(ethylene‐stat‐vinyl acetate) (PEVAc) on fumed silica was studied using temperature‐modulated differential scanning calorimetry (TMDSC) and FT‐IR spectroscopy. The properties of the copolymers were compared with poly(vinyl acetate) (PVAc) and low density polyethylene (LDPE) as references. TMDSC analysis of the copolymer‐silica samples in the glass transition region was complicated for the copolymers because of the ethylene crystallinity. Nevertheless, examination of the glass transition region for small adsorbed amounts of these copolymers indicated the presence of tightly‐ and loosely‐bound polymer segments, similar to other polymers which have an attraction to silica. Compared with bulk polymers with the same composition, the tightly‐bound polymers showed an increased glass transition temperature (T_g) and a loosely‐bound fraction with a lower T_g than bulk. FT‐IR spectra of the surface copolymers indicated that the fraction of bound carbonyls (p) increased as the fraction of vinyl acetate in the copolymers decreased, consistent with the notion that the carbonyls from vinyl acetate preferentially find their way to the silica surface. Spectra from samples with different adsorbed amounts of polymer were used to obtain the amount of bound polymer (M_b) and the ratio of molar absorption coefficients of bound carbonyls to free carbonyls (X). The copolymers had very large p values (up to 0.8) at small adsorbed amounts and dependent on the composition of the polymer. However, an analysis of the bound fractions, based on only the vinyl acetate groups, superimposed the data, suggesting that the ethylene units simply dilute the vinyl acetate groups in the surface polymer. The sample with the smallest fraction of vinyl acetate did not show this behavior and may be considered to be “carbonyl poor.” © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 727–736     

Carbon nanotube‐filled ethylene/vinylacetate copolymers: from in situ catalyzed polymerization to high‐performance electro‐conductive nanocomposites

Preparation and analysis of morphology, mechanical, and electrical properties of nanocomposites based on ethylene vinyl acetate (EVA) copolymer and commercial multiwalled carbon nanotubes (CNTs) was achieved. The used techniques for obtaining nanocomposites were the conventional melt‐mixing and the in situ ethylene polymerization/coating reaction, as catalyzed directly from CNT surface, with different polyethylene content (i.e. 55.0% and 66.6%). Nanocomposites were also prepared using crude CNTs. The incorporation in the molten state of such polyethylene surface‐coated CNTs, used as “masterbatch,” in EVA was demonstrated a good strategy for allowing the complete destructuring of the native bundle‐like aggregates, leading to the preparation of polymer nanocomposites with largely improved properties, even at very low nanofiller content. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of the liquid–liquid phase separation on the crystallization behavior of a poly(ethylene‐ran‐vinyl acetate) and paraffin wax blend

The effect of liquid–liquid phase separation (LLPS) on the crystallization behavior of poly(ethylene‐ran‐vinyl acetate) with a vinyl acetate content of 9.5 wt % (EVA‐H) in the critical composition of a 35/65 (wt/wt) EVA‐H/paraffin wax blend was investigated by small‐angle light and X‐ray scattering methods and rheometry. This blend exhibited an upper critical solution temperature (UCST) of 98°C, and an LLPS was observed between the UCST and the melting point of 88°C for the EVA‐H in the blend. As the duration time in the LLPS region increased before crystallization at 65°C, both the spherulite size and the crystallization rate of the EVA‐H increased, but the degree of the lamellar ordering in the spherulite and the degree of crystallinity of the EVA‐H in the blend decreased. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 707–715, 2000     

Effect of the liquid–liquid phase separation on the crystallization behavior and mechanical properties of poly(ethylene‐ran‐vinyl acetate) and paraffin wax blend

The effect of liquid–liquid phase‐separation (LLPS) on the crystallization behavior and mechanical properties of poly(ethylene‐ran‐vinyl acetate) (EVA) with various amounts of vinyl acetate and paraffin wax blend was investigated. The blend of EVA‐H (9.5% vinyl acetate) and the wax became homogeneous at temperatures greater than its upper critical solution temperature (UCST) (98°C), and an LLPS was observed between UCST and the melting point of 88°C for EVA‐H in the blend. The existence of the LLPS is attributed to the relatively large amount of the hydrophilic component of vinyl acetate in EVA, although the molecular weight of the wax was just 560. However, LLPS did not occur for the EVA/wax blend when the content of vinyl acetate in EVA was less than 3%. This behavior was explained by using the Flory–Huggins lattice model with an effective interaction parameter. The degree of crystallinity of EVA‐H in the EVA‐H/wax blend, judged from a melting endothermic peak in differential scanning calorimeter (DSC) thermograms obtained during heating runs, decreased with increasing duration time in the LLPS region. The flexural modulus of the EVA/wax blend became maximum at certain blend composition (about 30 ∼ 40 wt % EVA depending upon the amount of vinyl acetate). This behavior can be explained by the fact that this blend composition has the largest relative degree of crystallinity of EVA measured by DSC and wide‐angle X‐ray scattering method. We found that the flexural modulus of the binder itself is directly related to that of a feedstock consisting of larger amounts of metal powder and the binder, which can help someone to develop a suitable binder system for a powder injection molding process. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1991–2005, 1999     

Selective distribution,reinforcement, and toughening roles of MWCNTs in immiscible polypropylene/ethylene‐co‐vinyl acetate blends

Polypropylene/ethylene‐co‐vinyl acetate (PP/EVA) nanocomposites with functionalized multiwalled carbon nanotubes (FMWCNTs) have been prepared. The dissolution experiment, transmission electronic microscope, and scanning electronic microscope characterizations prove that, in the nanocomposites with sea–island morphology, although some FMWCNTs are observed in both PP and EVA phases, most of FMWCNTs distribute at the interface; however, in the nanocomposites with cocontinuous morphology, FMWCNTs mainly distribute in EVA phase. Further results based on (differential scanning calorimetry) measurements show that the different dispersion states of FMWCNTs, which are resulted by the different melt blending sequences, result in the different crystallization behaviors of PP matrix. The mechanical measurements show that FMWCNTs exhibit apparent reinforcement and toughening effects for immiscible PP/EVA blends, and such effects are greatly dependent upon the blending sequences. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1882–1892, 2010     

Toughening effect of ethylene‐vinyl acetate rubber on nylon 1010 compatibilized by maleated ethylene‐vinyl acetate copolymers

The toughening effect of ethylene‐vinyl acetate rubbers (EVM) with maleated ethylene‐vinyl acetate copolymers (EVA‐g‐MAH) on the nylon 1010 was investigated. The addition of 5 phr (per hundred nylon 1010) EVM increased the elongation at break of nylon 1010 to a great extent. The notched Izod impact strength of nylon/EVM blends increased with increasing EVM content. Scanning electron microscope showed that the EVM particle size was around 0.5 μm when the EVM content was 5 phr and increased with increasing EVM content. After the addition of EVA‐g‐MAH to nylon/EVM (100/20) blend, the average diameter of EVM particles decreased from more than 1 μm to 0.5–0.6 μm. EVA‐g‐MAH could improve the adhesion between nylon 1010 and EVM. A sharp brittle‐ductile transition (BDT) was observed when the interparticle distance was about 0.2 μm, independent of the addition of EVA‐g‐MAH. The notched Izod impact strength of nylon/EVM blends at low temperatures was measured and the BDT shifted toward low temperatures with increasing EVM or EVA‐g‐MAH content. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 434–444, 2009     

A comparative study of thermal ageing characteristics of poly(ethylene‐co‐vinyl acetate) and poly(ethylene‐co‐vinyl acetate)/carbon black mixture

In this comparative study, the effect of carbon black (CB) on the thermal ageing characteristics of poly(ethylene‐co‐vinyl acetate) (EVA) was investigated. EVA, containing 13% vinyl acetate (VA), and poly(ethylene‐co‐vinyl acetate)/carbon black mixture (EVA/CB) containing 13% VA and 1% CB were aged at 85°C in air up to 30 weeks. Sol‐gel analysis experiments were made to determine the percentage gelation of both virgin and aged samples. FT‐IR measurements were performed to follow the chemical changes which took place in the samples during ageing. Dynamic and isothermal thermogravimetric studies were performed for determination of the thermal stabilities of virgin and aged samples. Sol‐gel analysis results showed that EVA itself has a tendency to form a gel under thermal treatment, whereas EVA/CB never becomes a gel when being thermally aged under the same conditions. As a result of FT‐IR measurements, some oxidation products such as ketone, lactone and vinyl species were observed through thermal ageing of EVA. It is also clear that these kind of oxidation products did not appear to a considerable extent in EVA/CB. Thermal analysis experiments exhibit that thermal stability of EVA decreased through thermal ageing; whereas that of EVA/CB remained almost unchanged. Copyright © 2004 John Wiley & Sons, Ltd.     

A comparative study of UV aging characteristics of poly(ethylene‐co‐vinyl acetate) and poly(ethylene‐co‐vinyl acetate)/carbon black mixture

In this comparative study, the effect of carbon black (CB) on the UV aging characteristics of poly(ethylene‐co‐vinyl acetate) (EVA) was investigated. EVA, containing 13% vinyl acetate (VA), and poly(ethylene‐co‐vinyl acetate)/carbon black mixture (EVA/CB), containing 13% VA and 1% CB, were aged by means of UV light with a wavelength in the vicinity of 259 nm, in air, up to 400 hr. Sol‐gel analyses were made to determine the percentage gelation of both virgin and aged samples. FT‐IR measurements were performed to follow the chemical changes which took place in the samples during aging. Dynamic and isothermal thermogravimetry studies were performed for determination of the thermal stabilities of virgin and aged samples. Sol‐gel analysis results showed that EVA itself has a tendency to form a gel under UV irradiation. EVA/CB, however, becomes a gel to a smaller extent, comparatively, under the same conditions. As a result of FT‐IR measurements, some oxidation products such as ketone, lactone and vinyl species were observed through UV ageing of EVA and EVA/CB. Thermal analysis experiments exhibited that the thermal stabilities of EVA and EVA/CB decreased, to a similar extent through UV aging. Copyright © 2004 John Wiley & Sons, Ltd.     

Effects of filler–polymer interactions on cold‐crystallization kinetics in crosslinked,silica‐filled polydimethylsiloxane/polydiphenylsiloxane copolymer melts

Crystallization in a series of variable crosslink density poly(dimethyl‐diphenyl)siloxanes random block copolymers reinforced through a mixture of precipitated and fumed silica fillers has been studied by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), nuclear magnetic resonance (NMR), and X‐ray diffraction (XRD). The silicone composite studied was composed of 94.6 mol % dimethoylsiloxane, 5.1 mol % diphenylsiloxane, and 0.3 mol % methyl‐vinyl siloxane (which formed crosslinking after peroxide cure). The polymer was filled with a mixture of 21.6 wt % fumed silica and 4.0 wt % precipitated silica previously treated with 6.8 wt % ethoxy‐end‐blocked siloxane processing aid. Molecular weight between crosslinks and filler–polymer interaction strength were modified by exposure to γ‐irradiation in either air or in vacuo. Isothermal DMA experiments illustrated that crystallization at ?85 °C occurred over a 1.8 hour period in silica‐filled systems and 2.2–2.6 hours in unfilled systems. The crystallization kinetics for irradiated samples were found to be dependent on crosslink density. Irradiation in vacuo resulted in faster overall crystallization rates compared to air irradiation for the same crosslink density, likely due to a reduction in the interaction between the polymer chains and the silica filler surface for samples irradiated in air. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1898–1906, 2006     

Nonisothermal crystallization kinetics and determination of surface‐folding free energy of PP/EVA/OMMT nanocomposites

Crystalline structures, nonisothermal crystallization behavior and surface folding free energy of polypropylene (PP)/poly(ethylene‐co‐vinyl acetate) (EVA) blend‐based organically modified montmorillonite (OMMT) nanocomposites were investigated by use of wide angle X‐ray scattering (WAXS) and differential scanning calorimetry (DSC) techniques. Nonisothermal crystallization kinetic analysis was performed using Avrami equation modified by Jeziorny as well as combined Avrami‐Ozawa method. Surface folding free energy and activation energy for PP and nanocomposite samples were also determined employing Hoffman‐Lauritzen's and Vyazovkins's approaches, respectively. The results obtained from transmission electron microscopy (TEM) showed that presence of EVA, which attracts most of the layered silicates, reduces number density of heterogeneous nuclei in the matrix and as a consequence, decreases the nucleation rate. Incorporation of EVA, PP‐g‐MA and OMMT results in a decrease of the chain surface folding free energy level. It was shown that although, OMMT acts as a barrier against the PP macromolecular motion but interestingly, it increases the overall crystallization rate. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 674–684, 2009     

Synthesis of poly(vinyl acetate)‐b‐polystyrene and poly(vinyl alcohol)‐b‐polystyrene copolymers by cobalt‐mediated radical polymerization

Well‐defined poly(vinyl acetate) macroinitiators, with the chains thus end‐capped by a cobalt complex, were synthesized by cobalt‐mediated radical polymerization and used to initiate styrene polymerization at 30 °C. Although the polymerization of the second block was not controlled, poly(vinyl acetate)‐b‐polystyrene copolymers were successfully prepared and converted into amphiphilic poly(vinyl alcohol)‐b‐polystyrene copolymers by the methanolysis of the ester functions of the poly(vinyl acetate) block. These poly(vinyl alcohol)‐b‐polystyrene copolymers self‐associated in water with the formation of nanocups, at least when the poly(vinyl alcohol) content was low enough. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 81–89, 2007     

Preparation and Properties of Layered Silicate Nanocomposites Based on Ethylene Vinyl Acetate Copolymers

(Nano)composites based on ethylene vinyl acetate copolymers (EVA) and montmorillonite modified by various alkylammonium cations were processed by mechanical kneading. Polymer intercalation and filler exfoliation were evidenced by X‐ray diffraction and transmission electron microscopy, respectively. Nanocomposites tensile properties showed that Young's modulus increases significantly even at very low content of the organo‐modified filler while preserving high ultimate elongation and tensile stress. The matrix thermal stability in air was increased by 40°C and, interestingly, the obtained nanocomposites present flame retardant properties.     

Influence of mechanical properties,toughness, and barrier properties of PMMA‐EVA‐organoclay nanocomposites with and without in situ crosslinking

Poly methyl methacrylate (PMMA)‐ethylene vinyl acetate (EVA)‐organoclay nanocomposites were prepared with and without in situ crosslinking using tetrapropoxysilane (TPOS) as a crosslinking agent and dibutyl tin oxide (DBTO) as a catalyst. Brabender Plasticorder experimental results suggest that in situ crosslinking transforms the EVA from a liquid to a viscoelastic solid. Transmission electron micrographs analysis indicates that most of the organoclay was clustered in the crosslinked EVA phase. X‐ray diffraction and morphology indicate that the PMMA‐EVA‐organoclay nanocomposites were intercalated and incompatible. Dynamic mechanical analysis (DMA) results indicate some interaction between PMMA‐EVA‐clay nanocomposites. The in situ crosslinked of EVA and the addition of organoclay increased the modulus properties of PMMA. However, in situ crosslinking slightly reduced the barrier properties of PMMA‐EVA‐organoclay nanocomposites. Copyright © 2009 John Wiley & Sons, Ltd.     

Toughening of poly(L‐lactide)/multiwalled carbon nanotubes nanocomposite with ethylene‐co‐vinyl acetate

Poly(L ‐lactide)/multiwalled carbon nanotubes (PLLA/MWCNTs) nanocomposite recently attracts much attention because of its excellent comprehensive properties including improved thermostability, tensile strength, and conductivity. However, the nanocomposite exhibits similar brittleness compared with unmodified PLLA. In this work, a polar elastomer, that is, ethylene‐co‐vinyl acetate (EVA), was introduced into PLLA/MWCNTs nanocomposite. The selective distribution of MWCNTs and the effects of EVA on crystalline structure of PLLA were investigated using scanning electron microscope, transmission electron microscope, differential scanning calorimetry, and wide angle X‐ray diffraction. The results show that the presence of EVA induces the change of the distribution of MWCNTs in the nanocomposites, and consequently, the cold crystallization of PLLA is prevented. With the increase of EVA content, both the ductility and the impact resistance of PLLA/FMWCNTs are improved greatly, indicating the toughening effect of EVA on PLLA/MWCNTs nanocomposite. The decreased tensile strength and modulus can be compensated through annealing treatment. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

The effect of residual acetate groups on the structure and properties of vinyl alcohol–ethylene copolymers

Vinyl alcohol–ethylene (VAE) copolymers, commercially manufactured by hydrolysis of the corresponding vinyl acetate–ethylene copolymers, can contain small amounts of unhydrolyzed vinyl acetate. This article shows the influence of these residual groups on the structure of the resulting copolymers, studied by nuclear magnetic resonance and wide‐angle X‐ray scattering. Thermal and mechanical properties of these materials were investigated by differential scanning calorimetry, thermogravimetry, drawing behavior, birefringence measurements, and dynamic mechanical analysis. The structure of the copolymers is considerably affected by the volume of the residual acetate groups, bigger than that of the hydroxyl ones, which hinders the crystallization process. In relation to the thermal and mechanical properties, the temperature and enthalpy of melting as well as the Young's modulus and yield stress, decrease as vinyl acetate molar fraction increases. Moreover, the α and β relaxations are shifted to lower temperatures as residual content in the copolymer is raised. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 573–583, 2000     

Polyethylene Nanocomposite Heat‐Sealants with a Versatile Peelable Character

A novel heat‐sealing performance is achieved by polyethylene (PE) nanocomposites reinforced by ethylene vinyl acetate (EVA) and montmorillonite (MMT). Appropriate nanocomposite design leads to hermetic seals with a general peelable/easy‐open character across the broadest possible sealing temperature range. Observations of the fracture seal surfaces by infrared spectroscopy and electron microscopy reveal that this behavior originates from a synergistic effect of the EVA copolymer and the montmorillonite clay nanofiller. Namely, the combination of EVA‐copolymers and MMT nanofillers provides sufficiently favorable interactions for nanocomposite formation and mechanical robustness, but weak enough interfacial adhesion to promote a general cohesive failure of the sealant at the EVA/MMT interfaces.

     

Sorption and diffusion of normal alkanes through poly(ethylene‐co‐vinyl acetate) membranes

The transport behavior of uncrosslinked and crosslinked poly(ethylene‐co‐vinyl acetate) membranes has been investigated using normal alkanes as probe molecules, in the temperature range of 30–60 °C. Benzoyl peroxide was used for crosslinking the matrix. It has been observed that, a critical concentration of crosslinker is necessary for maximum solvent uptake, followed by a decrease at higher concentration. The effect of free volume on liquid transport was investigated by positron annihilation lifetime spectroscopy. The mechanism of transport has been found to deviate from the regular Fickian behavior. The dependence of the transport coefficients on crosslink density, nature of penetrants, and temperature was studied. The polymer–solvent interaction parameter, enthalpy, and entropy of sorption have also been estimated from the transport data. The affine and phantom models for chemical crosslinks were used to predict the nature of crosslinks. Finally, the experimental sorption data were compared with theoretical predictions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2470–2480, 2007