Multiscale Finite Element Modeling of Arc Dynamics in a DC Plasma Torch

The dynamics of the electric arc inside a direct current non-transferred arc plasma torch are simulated using a three-dimensional, transient, equilibrium model. The fluid and electromagnetic equations are solved numerically in a fully coupled approach by a multiscale finite element method. Simulations of a torch operating with argon and argon–hydrogen under different operating conditions are presented. The model is able to predict the operation of the torch in steady and takeover modes without any further assumption on the reattachment process except for the use of an artificially high electrical conductivity near the electrodes, needed because of the equilibrium assumption. The results obtained indicate that the reattachment process in these operating modes may be driven by the movement of the arc rather than by a breakdown-like process. It is also found that, for a torch operating in these modes and using straight gas injection, the arc will tend to re-attach to the opposite side of its original attachment. This phenomenon seems to be produced by a net angular momentum on the arc due to the imbalance between magnetic and fluid drag forces.     

Influence of the Shroud Gas Injection Configuration on the Characteristics of a DC Non-transferred Arc Plasma Torch

The characteristics of the plasma jet emanating from a dc non-transferred plasma torch is affected by many factors including arc current, type of gas, gas flow rate, gas injection configuration and torch geometry. The present work focuses on experimental investigation of the influence of shroud gas injection configuration on the I–V characteristics and electro-thermal efficiency of a dc non-transferred plasma torch operated in nitrogen at atmospheric pressure. The plasma gas is injected into the torch axially and shroud gas is injected through three different nozzles such as normal, sheath and twisted nozzles. The effects of flow rates of plasma/axial gas and arc current on I–V characteristics and electro-thermal efficiency of the torch holding different nozzles are investigated. The I–V characteristics and electro-thermal efficiency of the torch are found to be strongly influenced by the shroud gas injection configuration. The effect of arc current on arc voltage decreases with increasing the axial gas flow rate. At higher axial gas flow rate (>?45 lpm), the I–V characteristics of the plasma torch are similar irrespective of the nozzle used. The variation of electro-thermal efficiency with arc current is almost similar to that of arc voltage with arc current. As expected, the electro-thermal efficiency is increased when the axial gas flow rate is increased and at higher axial gas flow rate, it is not influenced by the arc current and shroud gas configuration. The plasma torch with normal nozzle may be better in the range of operating conditions used in this study.     

A Thermodynamic Analysis of Nonequilibrium Argon Plasma Torches

The nonequilibrium process of argon plasma torches is analyzed theoretically. Thermodynamic diagrams of different degrees of ionization are developed to aid in understanding and analyzing the transition from chemical equilibrium to frozen flow in dc plasma torch operations. A thermodynamic model is developed to describe the nonequilibrium processes in a dc argon plasma torch. In the model the ionization process is approximated as a constant-pressure heating process, with little deviation from the equilibrium state upon completion of heating. If the plasma flow is frozen shortly after heating, the entropy increase is small during the transition from equilibrium to frozen flow. In this case the frozen flow will have nearly the same composition and entropy as the flow at the heating section exit. For singly ionized argon plasmas in the entropy range relevant to dc torch operation, the frozen flow solutions on the affinity–pressure diagram are found to be insensitive to entropy change. Therefore the present model predicts that argon plasmas generated at different power levels will have almost identical affinity at the torch exit for the same operating pressure. This prediction agrees with experimental observations except for very low torch power levels.     

Electric Arc Fluctuations in DC Plasma Spray Torch

Direct current plasma torches for plasma spraying applications generate electric arc instabilities. The resulting fluctuations of input electrical power hamper a proper control of heat and momentum transfers to materials for coating deposition. This paper gives an overview of major issues about arc instabilities in conventional DC plasma torches. Evidences of arc fluctuations and their consequences on plasma properties and on material treatments are illustrated. Driving forces applied to the arc creating its motion are described and emphasis is put on the restrike mode that depends on the arc reattachment and the boundary layer properties around the arc column. Besides the arc root shown as a key region of instability, the Helmholtz oscillation is also described and accounts for the whole plasma torch domain that can generate pressure fluctuations coupled with voltage ones.     

Nanocarbon structures formed in a universal plasma reactor

The results of an instrumental study of a deposit formed on the electrodes of an arc plasma torch with propane-butane mixture feeding into the interelectrode gap are presented. The optical, electron, and Raman microscopy techniques have been used in the study. According to Raman spectra, the cathode deposit contains various forms of nanocarbon. It has been found that maleic anhydride is synthesized and covalently grafted to nanographite in the absence of a specialty catalyst during plasma torch operation. Having a large specific surface area, the nanocarbon itself acts as a heterogeneous catalyst in this case. It has been shown that an arc plasma torch of this design with a hydrocarbon feed gas can be considered a mini-reactor for synthesis of different forms of nanocarbon, its surface modification, and alteration of physicochemical properties.     

A high-powered A.C. plasma torch for the arc heating of molten steel in the tundish

Current user's requirements for excellent product quality means that producers must discover the isothermal casting conditions which trill lead to top operating performance in the continuous casting process. In response to this requirement. a high-powered A. C. plasma arc heating system was adopted for the No. 4 Continuous Caster (No. 4CC) put into operation at Kakogawa Works. This heating system is a single-phase A.C. plasma type with two torches. This report describes research on the molten steel heating technique utilized by the A. C. plasma system, the effects of tundish atmosphere on the characteristics of plasma electric potter, and the counter- measures devised to increase the arc voltage using a suitable torch structure.     

Effects of Nozzle Length and Process Parameters on Highly Constricted Oxygen Plasma Cutting Arc

The influence of nozzle length and two process parameters (arc current, mass flow rate) on the plasma cutting arc is investigated. Modeling results show that nozzle length and these two process parameters have essential effects on plasma arc characteristics. Long nozzle torch can provide high velocity plasma jet with high heat flux. Both arc voltage and chamber pressure increase with the nozzle length. High arc current increases plasma velocity and temperature, enhances heat flux and augments chamber pressure and thus, the shock wave. Strong mass flow has pinch effect on plasma arc inside the torch, enhances the arc voltage and power, therefore increases plasma velocity, temperature and heat flux.     

Generation of Long, Laminar Plasma Jets at Atmospheric Pressure and Effects of Flow Turbulence

Long, laminar plasma jets at atmospheric pressure of pure argon and a mixture of argon and nitrogen with jet length up to 45 times its diameter could be generated with a DC arc torch by restricting the movement of arc root in the torch channel. Effects of torch structure, gas feeding, and characteristics of power supply on the length of plasma jets were experimentally examined. Plasma jets of considerable length and excellent stability could be obtained by regulating the generating parameters, including arc channel geometry, gas flow rate, and feeding methods, etc. Influence of flow turbulence at the torch nozzle exit on the temperature distribution of plasma jets was numerically simulated. The analysis indicated that laminar flow plasma with very low initial turbulent kinetic energy will produce a long jet with low axial temperature gradient. This kind of long laminar plasma jet could greatly improve the controllability for materials processing, compared with a short turbulent arc jet.     

Comparative Study of Flow Characteristics Inside Plasma Torch with Different Nozzle Configurations

A numerical analysis of the influence of different nozzle configurations on the plasma flow characteristics inside D.C plasma torches is presented to provide an advanced nozzle design basis for plasma spraying torches. The assumption of steady-state, axis-symmetric, local thermodynamic equilibrium, and optically thin plasma is adopted in a two-dimensional modeling of plasma flow inside the plasma torch. The PHOENICS software is used for solving the governing equations, i.e. the conservation equations of mass, momentum, and energy along with the equations describing the K-epsilon model of turbulence. The calculated arc voltages are consistent with the experimental results when arc current, gas inflow rate, and working gas are the same as the experimental parameters. Temperature, axial velocity contours inside plasma torches, profiles along the torch axis and profiles at the outlet section are presented to show the plasma flow characteristics. Comparisons are made among those torches. The results show that torches with different anode nozzle configurations produce different characteristics of plasma flows, which suggest some important ideas for the advanced nozzle design for plasma spraying. In order to validate the model and to show its level of predictivity, a comparison of the model with experimental results encountered in the literature is presented in the last part.     

Effect of Anode Arc Root Position on the Behavior of the DC Non-transferred Plasma Jet at Field Free Region

A special bi-anode plasma torch that can change the anode arc root position without changing working gas flow rate has been developed to investigate the effect of anode arc root position on the behavior of the plasma jet. It has two nozzle-shaped anodes at different axial distances from the cathode tip. The arc root can be formed at anodes either close to the cathode tip (anode I) or far away from it (anode II) to obtain different attachment positions and arc voltages. The characteristics of pure argon plasma jets operated in different anode modes were measured in the field free region by using an emalpy probe, and the thermal efficiency of the torch was determined by measuring the temperature differences between cooling water flowing in and out of the torch. The results show that compared with the normal arc operated in anode I mode, the elongated arc operated in anode II mode significantly reduced the plasma energy loss inside the torch, resulting in a higher temperature and a higher velocity of the plasma jet in the field free region.     

Influence of the Gas Injection Angle on the Jet Characteristics of a Non-transferred DC Plasma Torch

The non-transferred direct current (DC) plasma torch has been widely used in various industrial applications due to its special jet characteristics. The jet characteristics are determined by different factors, including the working parameters, the torch construction, the gas injection angle (GIA) etc. As there is little study on the influence of the GIA on the jet characteristics, experimental study on the GIA’s effects on the jet characteristics has been carried out on a specially designed non-transferred DC plasma torch, whose GIA can be changed by replacing a gas injection component. The arc voltages and thermal efficiencies of the plasma torch, the specific enthalpies and jet lengths of the plasma jets at different working conditions were obtained and analyzed. It has been found that the GIA greatly affects the arc voltage, the thermal efficiency, the specific enthalpy and the jet length. Based on these findings, plasma torch with appropriate GIA could be used to help generating the plasma jet with desired characteristics.     

Heat Generation and Particle Injection in a Thermal Plasma Torch

The operation of plasma guns used for plasma spraying involves a continuous movement of the anode arc root. The resulting fluctuations of voltage and thermal energy input introduce an undesirable element in the spray process. This paper deals with the effects of these arc instabilities on the plasma jet, and the behavior of particles injected in the flow. The first part refers to the formation of the plasma jet. Measurements show that the static behavior of the arc depends strongly upon the plasma-forming gas mixture, especially the mass flow rate, of the heavy gas, injection mode, nozzle diameter, and arc current. These parameters control the electric field in the arc column, the arc length, its stability, and the gas velocity and temperature. The dynamic behavior of the arc is examined to determine how the tempeature and velocity of the plasma gas vary with voltage variations. Relationships between the gas velocity at the nozzle exit and the lifetime of the arc roots, and the independent operating parameters of the gun can be established from a dimensional analysis. The second part discusses the interaction between the plasma jet and the particles injected into the flow. The parameters controlling particle injection and trajectory are examined to determine how injection velocity must vary with particle size and density to achieve a given trajectory. The effect of the transverse injection of the powder carrier gas is investigated using a 3-D computational fluid dynamics code. Finally, the effect of the jet fluctuations on particle trajectory is studied under the assumption that the jet velocity follows the voltage variation. The result is a continuous variation of the particle spray jet position in the flow. Experimental observations confirm the model predictions.     

Characterization of d.c. plasma torch voltage fluctuations

The arc root fluctuations at the anode-nozzle of a d.c. plasma spray torch with a special configuration of the electrodes allowing to work with the same gas flowrate with nozzle diameters ranging from 6 to 10 mm were systematically studied. The plasma gas was Ar/H2 (25 vol % H2), the current was varied between 200 and 600 A and the plasma gas flowrate between 24 and 80 slm. After 30–60 mn working the nozzle wall started to be sufficiently eroded to have a stagnant arc spot which lived until arcing created another one. It was shown that the life time of the upstream arc spots were 30–40 % longer than the downstream ones which could play an important role in the electrode erosion. Dimensional analysis allowed to find a relationship between the nozzle diameter D, the arc current I and gas flow rate G and the mean spot lifetime which is closely connected with the difference between D and the electrical diameter of the arc column. The comparison of voltage signal and light emission at a point of the plasma jet close to the nozzle exit on its axis allowed to determine the mean electrical field within the plasma column and the mean position of the arc root. The comparison with the electrode erosion area for well defined conditions showed a good correlation with the calculated arc root position.     

Velocity Measurements for Arc Jets Produced by a DC Plasma Spray Torch

An optical method was used to determine the axial velocity of plasma jets produced by a DC plasma spray torch. Different experimental conditions were tested in order to systematically study the influence of the working parameters on the plasma velocity. In this way, the arc current ranged between 200 and 600 A, the gas flow rate between 30 and 80 slm, and the internal nozzle diameter between 6 and 10 mm; the plasma gases were either an Ar–H ₂ mixture or N ₂ . Rather well defined tendencies were observed and at the same time it appeared that the arc stability greatly influenced the fluctuations of the velocity.     

Development of a Submerged Thermal Plasma Process for Combustion of Organic Liquid Waste

Plasma Chemistry and Plasma Processing - A process for the destruction of organic liquid waste has been developed in which a nontransferred arc plasma torch is operated with oxygen as the plasma...     

High Speed Video Camera and Electrical Signal Analyses of Arcs Behavior in a 3-Phase AC Arc Plasma Torch

A 3-phase AC plasma torch has been developed and aims at overcoming some limits of the classical DC torches in terms of efficiency, cost and reliability. However, the arc behavior in 3-phase plasma torch remains poorly explored. This paper is dedicated to the high speed video camera at 100,000 frames per second and electrical signal analyses of arcs behavior in a 3-phase AC arc plasma torch. First, a reference case at 150 A, in nitrogen as working gas, has been deeply analyzed. Afterwards, a parametric study based on current and inter-electrode gap has been carried out. Results show that only one arc can exist at a given time and arcs rotate by switching from a pair of electrodes to another one, following the maximal electrical gap potential. However, a particular “abnormal” arc behavior was sometimes observed. Indeed, the arc motion within the inter-electrode gap increases the heat exchange and stabilizes the 3-phase discharge whereas the system is unbalanced when the arc is in the periphery. The analysis highlights that the arc motion is strongly influenced by the electrode jet velocity and repulsive Lorentz forces. The parametric study shows that the current increases both jet velocity and arc discharge stability. Elsewhere, the increase of the inter-electrode gap can also stabilizes the electrical 3-phase arc discharge. Furthermore, the correlation between arc motion and current waveform is highlighted. This work is likely to open the way toward a better understanding of 3-phase discharges in the perspective of their further optimization.     

Energy Fluctuations in a Direct Current Plasma Torch with Inter-Electrode Inserts Operated at Reduced Pressure

Direct current (dc) plasma torch with inter-electrode inserts has the merits of fixed arc length, relative high enthalpy and may show advantages in future plasma processes where stability and controllability are must-have. Energy fluctuations in the plasma may result from power supply ripple, arc length variation, and/or acoustic oscillation. Using an improved power supply with a flat waveform, the characteristics of an argon plasma energy instabilities under reduced pressure were studied by means of simultaneously monitoring the arc voltage and arc current spectrum. Dependence of the arc fluctuation behavior on the plasma generating parameters, such as the current intensity, the plasma gas flow rates and the vacuum chamber pressure were investigated and discussed. Results show that the plasma torch has a typical U-shaped voltage-ampere characteristic (VAC). The correlation between the VAC and the probability of energy distributions was studied. Through pressure measurements at the cathode cavity and the vacuum chamber, the existence of sonic flow in the inter-electrode insert channel was confirmed.     

Modeling of the Subsonic–Supersonic Flow and Heat Transfer in a DC Arc Plasma Torch

Two-dimensional modeling results are presented concerning the subsonic–supersonic flow and heat transfer within a DC plasma torch used for low-pressure (or soft vacuum) plasma spraying. The so-called fictitious anode method is used in the modeling in order to avoid inclusion of the complex three-dimensional effects near the anode arc root and also to avoid the forced heating of all the incoming cold gas stream by the arc. A nonorthogonal boundary-conforming grid, nonstaggered variable arrangement and the all-speed SIMPLE algorithm are employed for the solution of the governing equations, including gas viscous effects, temperature-dependent properties, and compressible effects. Good agreement of the predictions with available results for a few benchmarked compressible flow problems shows that the new version of the FAST-2D program can be employed for the present plasma flow modeling. Temperature, axial velocity, Mach number, and static pressure contours, and streamlines within the DC arc plasma torch are presented to show the flow and heat transfer characteristics. The flow transits gradually from upstream subsonic regime into downstream supersonic regime with the subsonic–supersonic transition within the cylindrical segment of the torch nozzle. Additional numerical tests show that gas viscosity and Lorentz force have only a slight effect on the plasma flow.     

Experimental Comparison of Methane Pyrolysis in Thermal Plasma

Methane pyrolysis via thermal plasma was investigated experimentally on a 2 kW DC arc plasma setup in argon atmosphere. Two widely applied methane pyrolysis profiles, i.e., pre-mixing methane and argon before fed into plasma torch, and injecting methane into pure argon plasma jet at torch outlet, were compared. Performances of methane pyrolysis regarding to methane conversion, acetylene selectivity, acetylene specific energy requirement (SER), and plasma stability were concluded. Results showed that pre-mixing methane and argon before fed into plasma torch would be efficient in converting methane and acetylene production, with higher conversion of methane and lower SER to acetylene at a given specific energy. Also, methane in arc zone would cause periodic fluctuations of plasma voltage and power, which could be reduced by controlling methane fraction in feed. On the other hand, when methane was injected into argon plasma jet at torch outlet, the energy efficiency in converting methane and producing acetylene would be lower. And the plasma would barely participate in the reaction other than providing heat, but the erosion of electrode was much slower and slighter. It was also validated that the SER of acetylene was limited by the thermal loss of the setup due to size-effect of reactor.     

Direct Measurement of the Gas Entrainment Into a Turbulent Thermal Plasma Jet

An experimental study is conducted to investigate the entrainment characteristics of a turbulent thermal plasma jet issuing from a DC arc plasma torch operating at atmospheric pressure. The mass flow rate of the ambient gas entrained into the turbulent plasma jet is directly measured by use of the so-called “porous-wall chamber” technique. It is shown that a large amount of ambient gas is entrained into the turbulent plasma jet. With the increase of the gas mass flow rate at the plasma jet inlet or the plasma torch exit, the mass flow rate of entrained ambient gas almost linearly increases but its ratio to the jet-inlet mass flow rate decreases. The mass flow rate of the entrained gas increases with the increase of the arc current or jet length. It is also found that using different ways to inject the plasma-forming gas into the plasma torch affects the entrainment rate of the turbulent plasma jet. The entrainment rate expression established previously by Ricou and Spalding (J. Fluid Mech. 11: 21, 1961) for the turbulent isothermal jets has been used to correlate the experimental data of the entrainment rates of the turbulent thermal plasma jet, and the entrainment coefficient in the entrainment rate expression is found to be in range from 0.40 to 0.47 for the turbulent thermal plasma jet under study.