3-氰基-5-[2-(3-乙基-2-苯并噻唑啉基)亚乙基] 4-苯基-2(5H)-呋喃酮蒸发膜的结构与光、电导性能的关系

众所周知, 部花著染料已作为照相材料的光学增感剂, 并可能作为太阳能电池及光导器件材料, 本工作就是为了探索这种材料进行了标题化合物的合成, 单晶的培养, 蒸发膜的研制及其性能的研究, 并探讨了结构与性能的关系及其导电机制。     

电化学聚对苯膜的现场ESR及其性能研究

本文用现场电化学-ESR联合测试的技术, 对电化学聚对萃膜在浓H_2SO_4中的性质进行了研究, 结果表明: 聚对苯膜具有高的电导率和相对低的自旋磁化率, 极化子与偶极化子为主要导电者, 并在一定的电位下相互转化, 自旋粒子有很大的离域性。膜中链与链之间可能存在部分的氧桥结构, 而引起体系结构的某些变化, 使聚对苯膜的电导提高以及掺杂容易进行。掺杂量受电位控制, 浓H_2SO_4中的HSO_4~-嵌入/脱嵌的电化学可逆性很好, 最大掺杂量可相当于每5个苯环单元氧化出一个正电荷, 可望将电化学聚对苯用作稳定的二次电池电极材料。     

Effects of polymerization media on the nanoscale conductivity and current-voltage characteristics of chemically synthesized polyaniline films

A current sensing atomic force microscope (CS-AFM) was used to probe the conducting homogeneity and band structures of fully doped polyaniline (PANI) films prepared from in situ chemical polymerization/deposition of aniline on indium tin oxide in various inorganic acids. The charge transport properties of PANI films depend on the film thickness as well as polymerization medium. Fluctuations in conductivity are observed on all acid-doped PANI films and the conducting homogeneity was dependent on the film thickness: the conductivity of thick film is more uniform. The current-voltage (I-V) characteristics of all thick (>200 nm) films displayed a metal-like behavior and conductivity as high as 40 S/cm was detected in high conducting regions of film thicker than 400 nm. Whereas thin (<120 nm) films revealed insulating, semiconducting, and semimetal conducting, wide distribution in conductivity and interband distances (estimated from the I-V ordI/dV-V curves) was found. The interband distances is 0-1.35, 0-1.0, and 0-0.78 eV for thin PANI film prepared from HCl(aq), HClO(4)(aq), and H2SO4(aq), respectively. PANI film (260 nm) prepared from H2SO4(aq) revealed fiberlike morphology, and compared to PANI films prepared from HCl(aq) and HClO4(aq) with similar thickness, it has higher average nanoscale conductivity but lower bulk conductivity. This result could be direct evidence which supports that the bulk conductivity of PANI depended on the carriers hopping between the conducting domains.     

Study of polyaniline conducting/electroactive polymer as sensor for some agricultural phosphorus pesticides

Abstract  

Due to their wide applications as insecticides, pesticides, chemical warfare agents, etc., detection of organophosphorus compounds is of great importance. This paper deals with application of polyaniline conducting polymer (PANi) as a sensor material for detection of some agricultural organophosphorus compounds that are commonly used as insecticides and pesticides. The compounds employed in this investigation are dichlorvos, trichlorophon, and chlorpyrifos. The effects of some important parameters such as concentration, thickness of the polymer film, etc., on electrical conductivity and conductivity stability for these compounds have also been investigated. In situ electrical conductivity measurements were performed using a standard direct-current (DC) four-point probe technique. It was found that adsorption and desorption of these compounds on PANi film cause measurable change in the resistance of conducting polymers.     

CONFINING CONDUCTING POLYANILINE IN A STABLE INORGANIC NETWORK

Water soluble conducting polyaniline with electrical conductivity of 10~(-1)-10~(-2) S/cm was prepared employingdopant induced water solubility technology. The water resistance of the conducting film was significantly improvedemploying sol-gel hybrids method, especially when the conductive polyaniline loading was below 30 wt%. The reason forthe improvement is that the conducting polyaniline chains are confined in a stable inorganic network.     

STUDIES ON ENHANCED CONDUCTIVITY OF STRETCHED CONDUCTING POLYMERS

A physical model of series of the conductivity on chain and the interchain conductivitybetween chains is proposed to explain enhanced conductivity of stretched conducting polymers.This model suggests that the enhanced conductivity for stretched conducting polymers might bedue to increasing of the interchain conductivity between chains along the elongation direction afterdrawing processes if the conductivity on chain is assumed much larger than that of the interchainconductivity between chains. According to this model, it is expected that the temperaturedependence of conductivity measured by four-probe method for stretched conducting polymers iscontrolled by a variation of the interchain conductivity between chains with temperature, whichcan be used to explain that a metallic temperature dependence of conductivity for stretchedconducting polymers is not observed although the conductivity along the elongation direction isenhanced by two or three orders of magnitude.     

浸渍聚合法制备透明导电聚苯胺薄膜的研究

采用浸渍聚合法制备透明导电的聚苯胺薄膜，并系统地研究了基片、反应温度、氧化剂和掺杂剂等因素对聚苯胺透明导电薄膜的电学和光学性能的影响．在最佳的制备条件下，所得薄膜的室温电导率可达１～５Ｓ／ｃｍ．当厚度为０５μｍ时，在４５０至６５０ｎｍ的透光窗口内，该薄膜的透光率可达８０％．借助结构表征讨论了薄膜的生长机理和它的结构组成．     

SYNTHESIS AND PROPERTIES OF POLYMERIC BIS (ETHYLENEDITHIO)-TETRATHIAFULVALENES

A polymer containing bis(ethylenedithio)-tetrathiafulvalene moiety wassynthesized and its electrochemical properties were studied by cyclic voltammetry. Thecharge transfer complexes of the polymer with TCNQ and I_2 were obtained by chemicaloxidation in dichlorobenzene. All of them are semi-conductors. A film of the polymer wasobtained by casting. Its conductivity, after oxidation with iodine, is 2.24×10~(-6)S·cm~(-1)and its conducting state is stable in air.     

聚合物单阳离子导体的制备—羧酸型梳状单离子导体

本文报道一种制备聚合物单阳离子导体的新方法。马来酸酐－醋酸乙烯酯及马来酸酐－苯乙烯共聚物以聚乙二醇单甲醚醇解，使酸酐环打开而得到带有聚乙二醇侧链的羧酸型梳状聚合物，其锂盐在加入适当增塑剂成膜后，可作为聚合物单阳离子导体，其结构以非晶态为主，具有较低的玻璃化转变温度及较好的热稳定性，增塑后的室温电导率最高可达１０＾－６Ｓ／ｃｍ。此外还研究了聚合物结构、阳离子半径、增塑剂、温度及外加额率等因素对电导率     

Electrical properties of the YSZ/STO/YSZ-STO superlattice electrolyte film at low temperatures

This study is focused on characterization of the low temperature properties of the YSZ/STO/YSZ superlattice film deposited onto unilateral polished SrTiO₃ (STO) monocrystalline substrates using pulsed laser deposition (PLD). The phase composition, structure, surface morphology and electrical properties of the oxygen ion conducting electrolyte YSZ/STO/YSZ multilayers were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). The minimum conductivity activation energy of YSZ/STO/YSZ is 0.76 eV at 300–500°C. The YSZ/STO/YSZ superlattice film shows an enhancement in conductivity by three orders of magnitude compared to bulk YSZ at a temperature of 300°C.     

含有添加剂及LiClO_4的接枝聚酯网络的离子导电性能研究

研究了碳酸丙烯酯（添加量５％）与γ－丁内酯（添加量１０％）对由数均分子量为８００的聚氧化乙烯（ＰＥＯ８００）大单体交联不饱和聚酯（含ＬｉＣｌＯ４）形成的接枝聚酯网络的离子导电性能影响，发现其电导率主要取决于体系中的ＬｉＣｌＯ４浓度．当［ＥＯ链节］／［Ｌｉ＋］＝３０时，室温电导率达最大值，σ２９８Ｋ＝（４．０—４．５）×１０－５Ｓｃｍ－１．这类接枝聚酯网络的玻璃化转变温度（Ｔｇ）同样取决于盐类浓度，而与网络的交联程度无关．网络中的极性添加剂并不显著影响其交联程度与Ｔｇ，但较大幅度提高离子导电性能，这可能与极性添加剂加速载荷离子在导电通道中的迁移性有关．若在上述接枝网络中引入环氧树脂网络，形成接枝聚合物互穿网络，则成膜后的机械强度有进一步提高，同时具有优良的室温电导率，σ２９８Ｋ＝２．４×１０－５Ｓｃｍ－１。     

FREE STANDING FILM OF POLYANILINE

A free standing film of polyaniline as large as 18 cm×18cm×0.002 cm can be obtained by evaporation of a solution of the chemically synthesized base in NMP. Its structure was examined by the elemental analysis, IR, U.V.-visible spectra, XPS, DSC, SEM and X-ray scattering and its conducting behavior as well as electrochemical properties were studied. Results show that the composition, structure of main chain, physical properties of the free standing film of polyanilme is similar to that of the powder. However, some differences in its electronic structure, conductivity at room temperature and potential of redox couple between the flee standing film and powder are observed, which may be due to cross-linking of the film of polyaniline.     

Impedance change induced by varying polymerization temperature of conducting polymer thin films

In this study, we use a conducting polymer precursor to build layer-by-layer (LbL) films. Thermal conversion of the polymer precursor to conducting polymer makes the LbL films intractable, so the LbL films can be used as protective layers in salt solution. The conducting polymer LbL film shows stabilizing effect on top of another LbL thin film that contains nanoparticles. The LbL film prepared in this study shows a 35-fold increase of conductivity than the literature values obtained from non-conducting polymer films. The stabilization of the films is the result of the polymerization of the conducting polymer, so other anionic polymers or nanoparticles may be used to afford additional functionalities.     

Study on Conductivity Properties of PEDOT Prepared through a Modified LB Film Method

Adopting LB film method, an arachidic acid (AA)/PEDOT multilayer LB film was chosen, and polymerized EDOT monomers in hydrophilic group of LB to prepare arachidic acid (AA)/PEDOT multilayer LB film. UV‐Vis, FT‐IR and XPS analyses implied that EDOT was effectively polymerized in film, and thus PEDOT conducting polymer was produced. Analyses of XRR and SIMS indicated that film had a well‐arranged lamella structure, and further research showed that polymerization of EDOT in AA film destroyed the orderliness of the original LB film. This phenomenon could be related to the destructive effect of polymerization on layered structure. We used four‐point probe and semiconductor instrument to study the conductivity property of the film, and observed that the conductivity of AA/PEDOT film had sudden changes with the processing time of changes in effective conduction network. That was caused by "permeability" in conducting channel of multilayer film. The test results also indicated that the conductivity of AA/PEDOT film was obviously better than that of spin‐coating PEDOT/PSS film or that of ODA‐SA/PEDOT‐PSS film, which was due to the higher π structure of PEDOT structure and ordered film structure.     

尼龙6/石墨纳米导电复合材料的制备与性能

通过原位插层聚合制备了尼龙 6 /石墨纳米导电复合材料 ,其室温导电渗滤阈值为 =0 75vol% ,远远低于常规导电粒子填充的聚合物复合材料 .当石墨体积分数为 2 0vol%时 ,室温电导率可达 10 -4 S/cm .透射电镜研究表明 :由于石墨经高温膨胀后其片层被剥离导致了片状石墨粒子具有巨大的径厚比 ,经原位插层聚合其片层厚度进一步被剥离为几十个纳米 ,同时原位插层聚合使得石墨粒子能够均匀分散在尼龙 6基体中 ,因而导致了该导电复合材料的低渗滤阈值和高导电性能 .     

高导电聚苯胺薄膜的制备及其电磁屏蔽性能的研究

随着电器制品、电子器件的商用、军事用和科学应用的迅速增长 ,产生了亟待解决的电磁干扰 (也称作电磁环境污染 )问题 ,电磁干扰屏蔽日益受到关注 .本文从聚苯胺掺杂工艺角度出发 ,通过改变掺杂剂用量和溶剂种类 ,制备出高导电的聚苯胺薄膜 ,并对其电磁屏蔽特性进行了初步的测试与理论分析 ,将屏蔽效能的实测结果与理论计算值进行了比较     

Effect of surface pressure on the insulator to metal transition of a langmuir polyaniline monolayer

A remarkable change in the conductivity of a polyaniline (PAN) Langmuir monolayer in the conducting state, as a function of surface pressure, has been observed using scanning electrochemical microscopy (SECM). The film conductivity, as expressed by the SECM current response of a redox mediator, was measured in-situ in a Langmuir film balance. The conductivity of the film increases significantly with surface pressure, above a threshold value of ca. 20 mN m-1.     

Covalent immobilization of glucose oxidase on films prepared by electrochemical copolymerization of 3-methylthiophene and thiophene-3-acetic acid for amperometric sensing of glucose: Effects of polymerization conditions on sensing properties

For the purpose of glucose sensing, enzyme electrodes were fabricated via covalent immobilization of glucose oxidase on the films of conducting polymer. The films were prepared electrochemically by the copolymerization of 3-methylthiophene and thiophene-3-acetic acid. The properties of the films were investigated by taking into account the polymerization conditions (the kind of supporting electrodes, the current, the amount of passed charge, and the monomer concentration) and the dedoping treatment. The glucose sensing performance of the enzyme electrode was found to be affected markedly by the following three factors of the conducting polymer film: surface morphology, conductivity and cohesion with support electrodes. It was suggested that the ideal conducting polymer used for the enzyme electrode should be a thin film having high conductivity and ordered nanostructure.     

聚苯基单醚喹噁啉的合成及性能

聚苯基单醚喹噁啉是从芳香族四胺和芳香族四酮缩聚制得。我们以对苯二甲腈为原料,采用二甲基亚砜为氧化剂,简便地合成芳香族四酮。聚合时系统地研究了单体不同克分子比合成的树脂对各种性能的影响,从而对这类树脂的加工成型提供了实验的数据。我们认为这种树脂可以作为在水、化学介质或油环境中使用的绝缘材料。     

Synthesis and characterization of epoxidized polybutadiene/polyaniline graft conducting copolymer

In this article the synthesis and characterization of an elastomeric conducting material, obtained by grafting polyaniline (EB) on commercial cis‐1,4‐polybutadiene (PB), are described. PB was first partially epoxidized in chloroform solution using meta‐chloroperbenzoic acid (MCPBA). The conducting polymer was then grafted to the activated polybutadiene (EPB) via the aminolysis reaction between the polyaniline NH₂ terminal groups and the oxirane rings. The material so obtained (EPBPAN) and the epoxidized intermediate product were characterized by ¹H NMR, ¹³C NMR, Fourier transform infrared, and ultraviolet–visible spectroscopy, thermal and mechanical analysis, and electrical conductivity measurements. The effect of the sample deformation on conductivity also was analyzed. The HCl doping of the EPBPAN film induced crosslinking reactions, generated by the acid cleavage of unreacted oxirane groups. The electrical conductivity of the doped material reached values of about 10^?5 Ω^?1 cm^?1. The key characteristics of our elastomeric conducting material are its simple synthesis, its starting as a commercial product, and the solubility of its undoped form in a common low‐boiling organic solvent like chloroform. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3082–3090, 2004