Investigation of polyelectrolytes by total reflection X-ray fluorescence spectrometry

Water soluble polyelectrolyte samples containing mono-, bi- and trivalent metal ions were investigated without any pretreatment. Acid digestion of linear polymers may lead to a product insoluble in water so the digestion has to be avoided. The determination of analytical characteristics and limitations of the total reflection X-ray fluorescence (TXRF) analysis for poly(vinylalcohol-vinylsulfate) copolymers containing the following cations: Cs⁺; Ba²⁺; Cu²⁺ and La³⁺ are presented in this communication. On the basis of our results efficiency of ion-exchange during preparation of polyelectrolytes and stoichiometry of the end-product were determined. TXRF results were compared with data gained by inductively coupled plasma atomic emission spectrometry (ICP-AES) measurements except in the case of Cs⁺, which has poor sensitivity in ICP-AES. Good agreement was found between the results of the two techniques and calculations from titrimetric data. Concentration of Li⁺ and Mg²⁺ in polymer samples was measured only by ICP-AES.     

Extension of AOAC official method 999.14 (choline in infant formula and milk) to the determination of choline in dietary supplements

AOAC Official Method 999.14 is applicable for the determination of choline in milk and infant formulas. To date, its use has not been extended beyond these matrixes. We modified Official Method 999.14 and applied it to the determination of choline in a range of choline-containing dietary supplements. Dietary supplement tablets, capsules, wafers, softgels, liquid products, and drink powders were included. We found that the standard curve could be extended to cover a wider range of choline concentrations and defined a procedure for the use of Norit for samples in which the vitamin C content was high enough to interfere with the analysis. Recoveries of choline added to infant formula powders and to representative dietary supplement tablets, capsules, powdered drink mix, and wafer products were 85-114%. The use of Norit during the procedure did not affect the recovery of choline added to infant formula powders or to dietary supplements. An alkaline digestion was included for use with a product containing lecithin as the sole source of choline. Ten of 11 dietary supplement products analyzed by the modified method contained amounts of choline at or above declarations found on the product labels. The remaining product contained about 40% of the label-declared amount of choline.     

A method for trace element determination of single Daphnia specimens using total reflection X-ray fluorescence spectrometry

Two new preparation techniques for total-reflection X-ray fluorescence (TXRF) element determination of single freshwater crustacean specimens (dry weight: 3–40 μg ind⁻¹) have been developed and tested using Daphnia pulex from a deep, oligotrophic freshwater lake located in southern Chile. Dry method: Specimens were washed with 0.2 μm filtered lake water and frozen in liquid nitrogen. The freeze-dried Daphnia specimens were weighed using an ultra-fine microbalance and placed on quartz glass carriers for TXRF analysis. Wet method: Specimens were washed with 0.2 μm filtered lake water and placed on quartz glass carriers for TXRF analysis and dried in air. The dry weight was determined using the previously established body length–dry weight relationship. Method validation for both the dry and the wet preparation method in combination with TXRF spectrometry for the element determination in small single freshwater crustaceans showed that both methods can be used for routine investigations. There were no significant differences between the dry and the wet methods concerning the elements Ca, K, Fe, Zn, Br, P, Cu, but the determination of Mn, S and Sr revealed significant differences between the two methods. It seems that the dry method yields more precise results, but the wet method is easier to handle in the field when samples cannot be fixed with liquid nitrogen.     

Determination of total iodine in foods and dietary supplements using inductively coupled plasma-mass spectrometry

A method was developed and validated for the determination of total iodine in a wide variety of food products and dietary supplements. The method involves a unique sample digestion with a KOH solution in an oven or by using an open-vessel microwave system. After digestion, a stabilizer is added and the solution is taken to volume, then filtered and analyzed either directly or after dilution. The amount of iodine is determined with inductively coupled plasma-mass spectrometry (ICP-MS). The method was validated by experiments to determine its precision, accuracy, linearity, specificity, ruggedness, and robustness. The LOQ of this method is 25-50 microg/kg. The method demonstrated an average RSD of 2.27% during analysis of milk powder and 4.30% during analysis of a dietary supplement tablet reference material. The accuracy of the method as determined with these same reference materials was 100 and 94.2%, respectively. The method has been used successfully on commodity foods, processed foods, dairy products, pet food, infant formula, animal feed, mineral premixes, and a variety of dietary supplements.     

Determination of iodine anion in dried kelp and iodized throat tablets by reversed-phase ion-pair liquid chromatography with direct UV detection

Summary In this paper, the amount of iodine anion in dried kelp and iodized throat tablets was determined by reversed-phase ion-pair chromatography. A 300×4 mm I.D. columns packed with -Bondapak-C18 (5 m) was used and distilled water containing 10 mmol/l trimethylphenyl ammonium bromide was used as the eluent. UV detection at 231 nm was selected to monitor the iodine anion.     

Analytical determination of selenium in medical samples,staple food and dietary supplements by means of total reflection X-ray fluorescence spectroscopy

Selenium is essential for many aspects of human health and, thus, the object of intensive medical research. This demands the use of analytical techniques capable of analysing selenium at low concentrations with high accuracy in widespread matrices and sometimes smallest sample amounts.In connection with the increasing importance of selenium, there is a need for rapid and simple on-site (or near-to-site) selenium analysis in food basics like wheat at processing and production sites, as well as for the analysis of this element in dietary supplements. Common analytical techniques like electrothermal atomic absorption spectroscopy (ETAAS) and inductively-coupled plasma mass spectrometry (ICP-MS) are capable of analysing selenium in medical samples with detection limits in the range from 0.02 to 0.7 μg/l. Since in many cases less complicated and expensive analytical techniques are required, TXRF has been tested regarding its suitability for selenium analysis in different medical, food basics and dietary supplement samples applying most simple sample preparation techniques.The reported results indicate that the accurate analysis of selenium in all sample types is possible. The detection limits of TXRF are in the range from 7 to 12 μg/l for medical samples and 0.1 to 0.2 mg/kg for food basics and dietary supplements. Although this sensitivity is low compared to established techniques, it is sufficient for the physiological concentrations of selenium in the investigated samples.     

Extraction and detection of arsenicals in seaweed via accelerated solvent extraction with ion chromatographic separation and ICP-MS detection

An accelerated solvent extraction (ASE) device was evaluated as a semi-automated means of extracting arsenicals from ribbon kelp. The effect of the experimentally controllable ASE parameters (pressure, temperature, static time, and solvent composition) on the extraction efficiencies of arsenicals from seaweed was investigated. The extraction efficiencies for ribbon kelp (approximately 72.6%) using the ASE were fairly independent (< 7%) of pressure, static time and particle size after 3 ASE extraction cycles. The optimum extraction conditions for the ribbon kelp were obtained by using a 3 mL ASE cell, 30/70 (w/w) MeOH/H2O, 500 psi (1 psi = 7 KPa), ambient temperature, 1 min heat step, 1 min static step, 90% vol. flush, and a 120 s purge. Using these conditions, two other seaweed products produced extraction efficiencies of 25.6% and 50.5%. The inorganic species present in the extract represented 62.5% and 27.8% of the extracted arsenic. The speciation results indicated that both seaweed products contained 4 different arsenosugars, DMA (dimethylarsinic acid), and As(V). One seaweed product also contained As(III). Both of these seaweed products contained an arsenosugar whose molecular weight was determined to be 408 and its structure was tentatively identified using ion chromatography-electrospray ionization-mass spectrometry/mass spectrometry (IC-ESI-MS/MS).     

Instrumental Neutron Activation Analysis of Iodine Levels in Fourteen Seaweed Species from the Coastal Belt of Ghana

Fourteen seaweed species were sampled from October 1997 to May 1999 along the rocky shores of Ghana, which is being washed by the Gulf of Guinea (part of the Atlantic Ocean). Instrumental neutron activation analysis (INAA) was used to measure the iodine levels in the species, with the basic aim of selecting seaweed species that are rich in iodine and hence can be used as supplement in the diet of humans. This is to help solve the problems associated with iodine deficiency disorders (IDD). The levels of iodine found in the seaweed species ranged between 55 to 804 ppm. The precision, expressed in terms of relative standard deviation, and accuracy of measurements are within ±5–10%. The results show high variability in and between species and among sampling sites. The high values of iodine concentrations in the macroalgae suggest that these marine organisms can be used as supplement in the diet of humans.     

Extraction and detection of arsenicals in seaweed via accelerated solvent extraction with ion chromatographic separation and ICP-MS detection

An accelerated solvent extraction (ASE) device was evaluated as a semi-automated means of extracting arsenicals from ribbon kelp. The effect of the experimentally controllable ASE parameters (pressure, temperature, static time, and solvent composition) on the extraction efficiencies of arsenicals from seaweed was investigated. The extraction efficiencies for ribbon kelp (approximately 72.6%) using the ASE were fairly independent ¶(< 7%) of pressure, static time and particle size after 3 ASE extraction cycles. The optimum extraction conditions for the ribbon kelp were obtained by using a 3 mL ASE cell, 30/70 (w/w) MeOH/H₂O, 500 psi (1 psi = 7 KPa), ambient temperature, 1 min heat step, 1 min static step, 90% vol. flush, and a 120 s purge. Using these conditions, two other seaweed products produced extraction efficiencies of 25.6% and 50.5%. The inorganic species present in the extract represented 62.5% and 27.8% of the extracted arsenic. The speciation results indicated that both seaweed products contained 4 different arsenosugars, DMA (dimethylarsinic acid), and As(V). One seaweed product also contained As(III). Both of these seaweed products contained an arsenosugar whose molecular weight was determined to be 408 and its structure was tentatively identified using ion chromatography-electrospray ionization-mass spectrometry/mass spectrometry (IC-ESI-MS/MS).     

Perchlorate in seawater: bioconcentration of iodide and perchlorate by various seaweed species

There has been no reliable published data on the presence of perchlorate in seawater. Seaweeds are among the most important plant life in the ocean and are good sources of iodine and have been widely used as food and nutritional supplement. Perchlorate is known to inhibit the transport of iodide by the sodium iodide symporter (NIS), present e.g., in the thyroid and mammary glands. With perchlorate being increasingly detected in drinking water, milk and various other foods, increasing the iodide intake through inexpensive natural supplements may be an attractive solution for maintaining iodine assimilation. We report here measurable concentrations of perchlorate in several samples of seawater (detectable in about half the samples analyzed). We also report the iodide and perchlorate concentrations of 11 different species of seaweed and the corresponding bioconcentration factors (BCF) for perchlorate and iodide, relative to the seawater from which they were harvested. All seaweed samples came from the same region, off the coast of Northeastern Maine. Concentrations of iodide and perchlorate in four seawater samples collected from the region near harvest time were 30 ± 11 and 0.16 ± 0.084 μg l⁻¹, respectively. Concentrations of both iodide and perchlorate varied over a wide range for different seaweed species; iodide ranging from 16 to 3134 mg kg⁻¹ and perchlorate from 0.077 to 3.2 mg kg⁻¹. The Laminaria species had the highest iodide concentration; Laminaria digitata is the seaweed species most commonly used in the kelp tablets sold in health food stores. Our sample of L. digitata contained 3134 ± 15 mg iodide/kg dry weight. The BCF varied widely for different species, with Laminaria species concentrating iodide preferentially over perchlorate. The iodide BCF (BCF_i) to perchlorate BCF (BCF_p) quotient ranged from 0.66 to 53; L. digitata and L. saccarina having a BCF_i/BCF_p value of 45 and 53, respectively, far greater than a simple anion exchange process will allow. Although most seaweed samples contain some amount of perchlorate, the great majority contains iodide in so much higher amount that at least for the commonly used Laminaria species, the iodide/perchlorate ratio is greater than the square of the perchlorate to iodide selectivity factor reported for the mammalian NIS and should thus lead to net beneficial iodine nutrition even in a two-stage mother-infant scenario.     

Analytical approaches for Hg determination in wastewater samples by means of total reflection X-ray fluorescence spectrometry

At present, there is a considerable interest in Hg monitoring in wastewater samples due to its widespread occurrence and the high toxicity of most of its compounds. Hg determination in water samples by means of total reflection X-ray fluorescence spectrometry (TXRF) entails some difficulties due to the high vapor pressure and low boiling point of this element that produce evaporation and loss of Hg from the surface of the reflector during the drying process, commonly used for sample preparation in TXRF analysis.The main goal of the present research was to develop a fast and simple chemical strategy to avoid Hg volatilization during the analysis of wastewater samples by TXRF spectrometry. Three different analytical procedures were tested for this purpose: (i) increasing the viscosity of the wastewater sample by adding a non-ionic surfactant (Triton^® X-114), (ii) Hg immobilization on the quartz reflectors using the extractant tri-isobutylphosphine (Cyanex 471X) and (iii) formation of a stable and non-volatile Hg complex into the wastewater sample. The best analytical strategy was found to be the formation of a Hg complex with thiourea (pH = 10) before the deposition of 10 μL of sample on the reflector for following TXRF analysis. Analytical figures of merit such as linearity, limits of detection, accuracy and precision were carefully evaluated. Finally, the developed methodology was applied for the determination of Hg in different types of wastewater samples (industrial effluents, municipal effluents from conventional systems and municipal effluents from constructed wetlands).     

An electrochemical enrichment procedure for the determination of heavy metals by total-reflection X-ray fluorescence spectroscopy

An electrolytic separation and enrichment technique was developed for the determination of trace elements by total-reflection X-ray fluorescence spectroscopy (TXRF). The elements of interest are electrodeposited out of the sample solution onto a solid, polished disc of pure niobium which is used as sample carrier for the TXRF measurement. The electrochemical deposition leads to a high enrichment of the analytes and at the same time to a removal of the matrix. This results in substantially improved detection limits in the lower picogram per gram region. The deposited elements are directly measured by TXRF without any further sample preparation step. The homogeneous thin layer of the analytes is an ideal sample form for TXRF, because scattered radiation from the sample itself is minimized. The proposed sample preparation method is useful particularly for the analysis of heavy metals in liquid samples with for TXRF disturbing matrices, e.g. sea water.     

Determination of trace elements in bee honey,pollen and tissue by total reflection and radioisotope X-ray fluorescence spectrometry

Multielemental determinations in samples of various types of bee honey, pollen and bee tissue have been carried out using total reflection X-ray fluorescence spectrometry (TXRF) and radioisotope excited X-ray fluorescence spectrometry (XRF). The objective was to establish whether the elemental content of bee honey, in particular, correlates with any useful information about the environment, variety of honey, etc. An attempt has also been made to determine the X-ray techniques' ability to compete with atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES), with regard to elemental sensitivity, accuracy, sample preparation procedures, and in particular, economic performance, which is very important in selecting an appropriate technique for the analysis of large numbers of samples. The results confirm the advantages of the TXRF method for trace element analysis, but only when utilising monochromatic excitation and selecting a proper sample preparation procedure. The radioisotope XRF technique, which does not require any sample preparation, is still very competitive in analysis of elements with concentrations above a few ten ppm. Preliminary results also confirm some correlations between the elemental content of honey and the status of the environment, and encourage further work in this direction     

Novel Bio-Coacervation Extraction of Selenium Based on Microassemblies Biosurfactants with Ionic Liquid and Quantitative Analysis by HPLC/UV

In this work, we introduce a new sample preparation method for the extraction and preconcentration of selenium in dietary supplement tablets and mineral water. The bio-coacervation extraction technique is based on the use of a three-part system consisting of an ionic liquid, a biosurfactant and water. The advantage of this method is that the three components are non-toxic, green and eco-friendly. Parameters affecting the extraction efficiency, such as the amount of biosurfactant, the volumes of water and ionic liquid, pH, ionic strength, time extraction, temperature and the extraction method, were optimized. The calibration graph was linear, in the range of 0.55–40 µg L⁻¹. The detection limit for selenium after quantitative analysis was 0.183 µg L⁻¹ and the enrichment factor 190. The relative standard deviation for six replicate measurements was 4.6 %.

     

Capability and limitations of the determination of sulfur in inorganic and biological matrices by total reflection X-ray fluorescence spectrometry

The capability and limitations of TXRF were explored for the determination of the light element sulfur in inorganic and biological samples. The recovery rates of sulfur were measured with tungsten L-radiation in the dry residues of various sulfates and sulfur containing amino acids with a sulfur concentration ranging from 0.5 to 20 mg/l. Furthermore, the surface topography of the dry residues of the samples was investigated by scanning electron microscopy (SEM) and their thickness profiles were recorded by an Alpha-Step. The results show that the reliable determination of sulfur in inorganic samples depends on the cation involved. Alkali sulfates tend to form bulky residues which disturb the determination of sulfur distinctly due to absorption effects of the soft sulfur K radiation. In this case the use of smoothing detergents like 1% HF, 1% malic acid and 2% hydrazine hydrate is necessary for the determinations with reasonable accuracy (tolerance range: ±10% of the recovery rate). The results for the biological samples measured agree well with the expected values. The investigations lead to the conclusion that TXRF combined with a proper sample preparation is well suited for the determination of sulfur in samples of various matrices in a wide range of concentrations.     

Determination of metal-cofactors in respiratory chain complexes by total-reflection X-ray fluorescence spectrometry (TXRF)

Total Reflection X-Ray Fluorescence Spectrometry (TXRF) offers many advantages for the detection of trace elements in enzymes as compared to other well known analytical techniques like flame-AAS or ICP-AES because of the significantly smaller amounts of sample required. Without any decomposition, elements like Fe, Ni, Cu, Zn, Mn and Mo could be determined with high accuracy, in spite of the large bio-organic matrix. Besides the metals also sulfur can be determined in protein samples. The two terminal oxidases, cytochrome c oxidase and quinol oxidase, isolated from the soil bacterium Paracoccus denitrificans, were transferred from their usual salt buffer into a solution of 100 mmol/L tris(hydroxymethyl)aminomethane (TRIS) acetate containing an appropriate detergent. By this procedure an improved signal/noise ratio is attained. The data for cytochrome c oxidase are in good agreement with values obtained by ICP-AES. Further results of quinol oxidase, which has different element ratios, also fit the expected values. The investigations lead to the conclusion that the method is well suited for the quantitative determination of metals in enzymes, and in particular their molar ratios, and requires only small amounts of the biological sample without any extensive pretreatment.     

Determination of metal-cofactors in respiratory chain complexes by total-reflection X-ray fluorescence spectrometry (TXRF)

Total Reflection X-Ray Fluorescence Spectrometry (TXRF) offers many advantages for the detection of trace elements in enzymes as compared to other well known analytical techniques like flame-AAS or ICP-AES because of the significantly smaller amounts of sample required. Without any decomposition, elements like Fe, Ni, Cu, Zn, Mn and Mo could be determined with high accuracy, in spite of the large bio-organic matrix. Besides the metals also sulfur can be determined in protein samples. The two terminal oxidases, cytochrome c oxidase and quinol oxidase, isolated from the soil bacterium Paracoccus denitrificans, were transferred from their usual salt buffer into a solution of 100 mmol/L tris(hydroxymethyl)aminomethane (TRIS) acetate containing an appropriate detergent. By this procedure an improved signal/noise ratio is attained. The data for cytochrome c oxidase are in good agreement with values obtained by ICP-AES. Further results of quinol oxidase, which has different element ratios, also fit the expected values. The investigations lead to the conclusion that the method is well suited for the quantitative determination of metals in enzymes, and in particular their molar ratios, and requires only small amounts of the biological sample without any extensive pretreatment. Received: 17 June 1997 / Revised: 21 November 1997 / Accepted: 27 November 1997     

Simultaneous quantitation of six major quassinoids in Tongkat Ali dietary supplements by liquid chromatography with tandem mass spectrometry

Tongkat Ali (Eurycoma longifolia) is one of the most popular traditional herbs in Southeast Asia and generally consumed as forms of dietary supplements, tea, or drink additives for coffee or energy beverages. In this study, the liquid chromatography with tandem mass spectrometry method for the simultaneous quantitation of six major quassinoids of Tongkat Ali (eurycomanone, 13,21‐dihydroeurycomanone, 13α(21)‐epoxyeurycomanone, 14,15β‐dihydroxyklaineanone, eurycomalactone, and longilactone) was developed and validated. Using the developed method, the content of the six quassinoids was measured in Tongkat Ali containing dietary supplement tablets or capsules, and the resulting data were used to confirm the presence of Tongkat Ali in those products. Among the six quassinoids, eurycomanone was the most abundant quassinoid in all samples tested. The developed method would be useful for the quality assessment of Tongkat Ali containing dietary supplements.     

Determination of hydrastine and berberine in goldenseal raw materials, extracts, and dietary supplements by high-performance liquid chromatography with UV: collaborative study

A multilaboratory collaborative study was conducted on a high-performance liquid chromatographic (HPLC) method utilizing UV detection, previously validated using AOAC single-laboratory validation guidelines for determination of hydrastine and berberine in goldenseal (Hydrastis canadensis L.) raw materials, extracts, and dietary supplements at levels ranging from 0.4 to 6% (w/w). Nine collaborating laboratories determined the hydrastine and berberine content in 8 blind samples. Sample materials included powdered botanical raw materials, whole root material, and 4 finished product dietary supplements containing either goldenseal powdered root material or extract. The materials were extracted with an acidified water and acetonitrile solution. HPLC analyses of the extracts were performed on a C18 column using UV detection at 230 nm. Results for powdered root material and capsule products ranged from about 0.2% (w/w) for each alkaloid to about 4% (w/w) for each alkaloid. Liquid tincture results were approximately 4000-5000 microg/mL for each alkaloid. Reproducibility relative standard deviations (RSDR) for hydrastine ranged from 2.68 to 6.65%, with HorRat values ranging from 0.77 to 1.89. RSDR for berberine ranged from 5.66 to 7.68%, with HorRat values ranging from 1.32 to 2.12. All finished products containing goldenseal extract yielded HorRat values <2.0. Based on these results, the method is recommended for Official First Action for determination of hydrastine and berberine in goldenseal raw materials and dietary supplement finished products containing powdered goldenseal and goldenseal extract.     

Elemental Analysis of Copper-Zinc Ores by Total Reflection X-Ray Fluorescence using Nonaqueous Suspensions

Novel rapid determination of copper-zinc ore elemental composition by total reflection X-ray fluorescence (TXRF) is proposed. Approaches for solid state sample analysis by TXRF are provided. The sample preparation is chosen to obtain the suspensions in ethylene glycol. The optimum suspension preparation conditions (sample mass, volume of dispersion medium) and the measurement conditions (internal standard element, spectra acquisition time) were determined. The sedimentation stability of suspensions was studied. It was found that the suspensions remain stable for approximately 2?min, which is sufficiently long for the sampling the suspension. The proposed technique allows determining the elemental composition of solid ore samples without sample digestion. The sample preparation time takes approximately 20?min. The relative standard deviation of the analytical results did not exceed 10%.