The sol–gel chromium-modified V<Subscript>6</Subscript>O<Subscript>13</Subscript> as a cathodic material for lithium batteries

A new V₆O₁₃-based material has been synthesized via the sol–gel route. This sol–gel mixed oxide has been obtained from an appropriate heat treatment of the chromium-exchanged V₂O₅ xerogel performed under reducing atmosphere. This new compound, with the chemical formula Cr_0.36V₆O_13.50, exhibits a monoclinic structure (C2/m) with the following unit cell parameters, a=11.89 Å, b=3.68 Å, c=10.14 Å, β=101.18°. The electrochemical characterization of this compound has been performed using galvanostatic discharge–charge experiments in the potential range 4–1.5 V and completed by ac impedance spectroscopy measurements. It exhibits a specific capacity of about 370 mAh g^?1, which makes the compound Cr_0.36V₆O_13.50 the best one in the V₆O₁₃-based system: 85% of the initial capacity (315 mAh g^?1) after the 35th cycle is still available at C/25 without any polarization. From impedance spectroscopy, a high kinetics of Li transport (D _Li=1.8×10^?9 cm² s^?1) is found at mid-discharge.     

Subsolidus phase relations in the Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Li<Subscript>2</Subscript>O-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript> (Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>) systems

The phase composition has been studied and an equilibrium phase diagram has been designed for the Al₂O₃-Li₂O-R₂O₅ (R = Ta or Nb) systems in the subsolidus region up to 1000°C and 85 mol % Li₂O. New phases with the composition Li_1+x Al_1?x O_2?x , where x = 0–0.67, have been found.     

Supramolecular architecture of catechol and its 2:1 complex with dimethylsulfoxide

The crystal structures of catechol (o-dihydroxybenzene) and its 2:1 complex with dimethylsulfoxide are determined at T = 150 K. Crystal data: C₁₄H₁₈O₅S, M = 298.37, triclinic, space group P \(\bar 1\), unit cell parameters: a = 7.7285(13) Å, b = 9.9924(17) Å, c = 10.3188(18) Å, α = 89.963(4)°, β = 89.968(4)°, γ = 69.076(5)°, V = 744.3(2)ų, Z = 2, D _x = 1.331 g/cm³, R1 = 0.048; C₆H₆O₂, M = 110.11, monoclinic, space group P2₁/n, a = 9.8206(6)Å, b = 5.5903(3)Å, c = 10.4439(6)Å, β = 114.952(2)°; V = 519.85(5) ų, Z = 4, D _x = 1.407 g/cm³, R1 = 0.0289. In the 2:1 complex the molecules are joined in a supramolecular ensemble by D-H...A hydrogen bonds (D = O, C; A = O, π); in catechol they are bonded only by O-H...O. The state diagram of the catechol-dimethylsulfoxide system is examined by DTA.     

<Emphasis Type="Italic">cis</Emphasis>-Dioxomolybdenum(VI) complexes of sterically encumbered phenol-based tetradentate N<Subscript>2</Subscript>O<Subscript>2</Subscript> ligands: Structural,spectroscopic, and electrochemical studies

Two cis-dioxomolybdenum(VI) complexes [MoO₂L] (L: L ¹, 2 and L: L ², 3) in a phenol-based sterically encumbered N₂O₂ ligand environment have been synthesized, and their crystallographic characterizations are reported. The orange crystals of 2 are monoclinic, space group P2₁/a with unit cell dimensions as a=16.2407(17) Å, b=7.2857(8) Å, c=18.400(2) Å, β=98.002(9)°, Z=4, and d _cal=1.486 g cm^?3. The light orange crystals of 3, however, are orthorhombic, space group, Pbcn, with unit cell dimensions a=8.3110(12) Å, b=12.637(3) Å, c=34.673(5) Å, Z=4, and d _cal=1.187 g cm^?3. The structures were refined by a full-matrix least-squares procedure on F ² to a final R=0.046 (0.055 for 3) using 4944 (3677) all independent data. In both the cases, the Mo atom exists in a distorted octahedral geometry defined by a N₂O₄ donor set, which features a cis-Mo(–O)₂ and a trans-Mo(OPh)₂ arrangement. Compound 2 undergoes a quasireversible one-electron reduction at ?1.3 V vs Ag/AgCl reference due to Mo^VIO₂/Mo^VO₂ electron transfer and thus providing a rare example of steric solution to the comproportionation–dimerization problem encountered frequently in the development of valid biomimetic models for the active sites of oxomolybdenum enzymes.     

Phase composition,formation parameters,and morphology of precipitates in the LiVO<Subscript>4</Subscript>-VOSO<Subscript>4</Subscript>-H<Subscript>2</Subscript>O system

The phase and chemical compositions of the precipitates formed in the LiVO₃-VOSO₄-H₂O system at initial pH within 1 ≤ pH ≤ 4 and 90°C were studied. The following phases were prepared: an α phase Li_1.4(VO)_1.3[H₂V₁₀O₂₈] · nH₂O and a β phase Li_{0.6 ? x} H_{1.4 + x} [V₁₂O_{31 ? y/2}] · nH₂O (0 ≤ x ≤ 0.5, 1.3 ≤ y ≤ 2.0) with a layered structure. Li_0.4V₂O₅ · H₂O nanorods with the interlayer distance 10.30 ± 0.08 Å were synthesized at 180°C in an autoclave. The morphology, IR spectra, and main formation processes for these polyvanadates were studied.     

The R<Subscript>2</Subscript>Pd<Subscript>3</Subscript>Ge<Subscript>5</Subscript> (R = La–Nd,Sm) germanides: synthesis,crystal structure and symmetry reduction

Direct synthesis and structural characterization of a series of polar rare earth palladium germanides of R₂Pd₃Ge₅ composition (R = La–Nd, Sm) is reported. The crystal structure of the Nd representative was determined by single-crystal X-ray diffraction analysis (U₂Co₃Si₅-type, SG: Ibam, oI40, Z = 4, a = 10.1410(6), b = 12.0542(8), c = 6.1318(4) Å, wR ₂ = 0.0306, 669 F ² values, 31 variables). The crystal structures of the other homologues were ensured by powder X-ray diffraction pattern analysis. A smooth variation of the cell dimensions is observed through the rare earth series. The structure of the studied compounds can be interpreted as consisting of a complex three-dimensional [Pd₃Ge₅]^δ? network spaced by the rare earth cations. Within the concept of symmetry reduction, a Bärnighausen tree is used to rationalize the related crystal structures of the RPd₂Ge₂, RPdGe₃ and R₂Pd₃Ge₅ ternary compounds, enriching the large family of the BaAl₄ derivatives. Moreover, syntheses with metal fluxes were performed, some of which were successful to obtain large crystals of La₂Pd₃Ge₅ (using Bi as solvent) and Nd₂Pd₃Ge₅ (using Pb as solvent) stoichiometry.     

Synthesis and study of high-temperature heat capacity of erbium orthovanadate

Orthovanadate ErVO₄ has been prepared by solid-phase synthesis from a stoichiometric mixture of high pure V₂O₅ and chemically pure Er₂O₃ by multistage calcination in air in the temperature range 873–1273 K. The effect of temperature (380–1000 K) on the heat capacity of orthovanadate ErVO₄ was studied by hightemperature calorimetry. Thermodynamic properties of erbium orthovanadate (enthalpy change H°(T)–H°(380 K), entropy change S°(T)–S°(380 K), and reduced Gibbs energy Φ°(T)) have been calculated from the experimental C_p = f(T) data. It has been shown that the specific heat varies in a row of oxides and orthovanadates of Gd-Lu naturally depending on the radius of the R³⁺ ion within the third and fourth tetrads.     

A New Sandwich Polyoxometalate Constructed from a Zn<Stack><Subscript>6</Subscript><Superscript>12+</Superscript></Stack> Hexagon Cluster Sandwiched by Two B-α-[BiW<Subscript>9</Subscript>O<Subscript>33</Subscript>]<Superscript>9−</Superscript>

A new sandwich polyoxometalate Na₄Zn₂[Zn₂(H₂O)₁₀(ZnCl)₆(B-α- BiW₉O₃₃)₂] · 40.5H₂O (1) has been obtained in aqueous solution and characterized by IR, UV, element analysis, TG and single-crystal X-ray analysis. Polyoxoanion 1 is composed of a Zn ₆ ¹²⁺ hexagon sandwiched by two [BiW₉O₃₃]^9? units, which is firstly observed in tungstobismutate. The crystal data for compound 1: Triclinic, space group P–1, a = 15.426(3) Å, b = 15.467(3) Å, c = 15.526(3) Å, α = 74.24(3)°, β = 64.37(3)°, γ = 60.73(3)°, V = 2905.3(1) ų, Z = 1.     

Structural and vibrational investigation of 1, 2-<Emphasis Type="Italic">bis</Emphasis>(3, 4-dimethoxyphenyl) ethane-1, 2-dione (Veratril): experimental and theoretical studies

The molecular and crystal structures of 1,2-bis(3,4-dimethoxyphenyl)ethane-1,2-dione (TMBZ = tetramethoxybenzil) were determined by a single-crystal X-ray diffraction, ¹H NMR, and FT-IR spectroscopy. The compound TMBZ (C₁₈H₁₈O₆, M _r = 330.32) crystallized in the orthorhombic Fdd2 space group wherein: a = 39.145(4), b = 18.167(2), c = 4.3139(5) Å and β = 90°, Z = 8. The packing of the molecules in the crystal lattice is stabilized by intermolecular C–H?O contacts in the herringbone arrangement. The molecular geometry and harmonic frequencies of TMBZ in the ground state were calculated utilizing density functional (B3LYP) method with the 6-311++G(d, p)-basis set. The density functional theory optimized the geometric structure, and vibrational wave numbers of TMBZ in gas phase were compared with the experimental data. A complete assignment of the fundamentals was proposed based on the total energy distribution calculation.     

2-Propylamino-5-[4-(2-hydroxy-3,5-dichlorobenzylideneamino) phenyl]-1,3,4-thiadiazole: X-ray and DFT-calculated structures

2-Propylamino-5-[4-(2-hydroxy-3,5-dichlorobenzylideneamino) phenyl]-1,3,4-thiadiazole, formulated as C₁₈H₁₆Cl₂N₄OS (I), was synthesized. The crystal and molecular structure of (I) have been determined by ¹H-NMR, IR, and X-ray single crystal diffraction. The compound (I) crystallizes in the monoclinic, space group P2(1)/c with unit cell parameters a = 9.0576(2) Å, b = 24.3382(8) Å, c = 9.0585(2) Å, M _r = 407.31, V = 1851.13(9) Å³, Z = 4, R ₁ = 0.036, and wR ₂ = 0.096. Molecular geometry from X-ray experiment of (I) in the ground state has been compared using the density functional method (B3LYP) with 6-31G(d) basis set. To determine conformational flexibility, molecular energy profile of (I) was obtained by semi-empirical (PM3) calculations with respect to selected degree of torsional freedom, which was varied from ?180° to +180° in steps of 10°. The results are indicative that the Schiff base, which contains a thiadiazole ring, prefers to be in E-configuration. In addition, molecular electrostatic potential, frontier molecular orbitals, and natural bond orbitals analysis were performed by the B3LYP/6-31G(d) method.     

X-ray diffraction study on phase transition of orthorhombic LiMnO2 in electrochemical conversions

Orthorhombic LiMnO₂ was synthesized by hydrothermal reaction. Phase transition during electrochemical process has been investigated using the high-resolution X-ray diffraction. Contrary to numerous earlier reports, phase analysis of the orthorhombic LiMnO₂ electrode cycled for three times evidences the irreversible structure transition from orthorhombic LiMnO₂ (Pmnm) to spinel LiMn₂O₄ (Fd3m) and rock salt Li_0.5Mn_0.5O (Fm \( \overline{3} \) m). Here, the spinel structure with a cell parameter a?=?8.241 (1) Å has a large cationic disorder on lithium and manganese sites, i.e., about 9% of the Li positions are occupied by Mn and vice versa. For Li_0.5Mn_0.5O, the cell parameter is a?=?4.121 (3) Å, and both Li⁺ and Mn³⁺ cations occupy the octahedral 4a sites with mole ratio 1:1. The quantity of Li_0.5Mn_0.5O phase is greatly dependent on cycling rate, namely, the higher the current density is, the larger the quantity of formed-rock salt structure is.     

Synthesis,crystal structure and fungicidal activity of 1-(4-chlorophenyl)-2-(5-((3,5-dimethyl-1H-pyrazol-1-yl)methyl)-4-phenyl-4H-1,2,4-triazol-3-ylthio)ethanone

A novel bis-heterocyclic compound was synthesized and characterized. The crystal structure of the title compound (C₂₂H₂₀ClN₅OS, Mr = 437.94) has been determined by single-crystal X-ray diffraction. The crystal is of triclinic, space group P-1 with a = 8.646 (2), b = 9.148 (3), c = 14.540 (4) Å, α = 94.422 (4), β = 98.500 (4), γ = 102.823 (4)°, V = 1101.8 (5) Å³, Z = 2, F(000) = 312, Dc = 1.320 g/cm³, μ = 0.2900 mm^?1, the final R ₁ = 0.041000 and wR ₂ = 0.1160 for 2675 observed reflections with I > 2σ(I). A total of 5623 reflections were collected, of which 3866 were independent (R _int = 0.019000). The fungicidal activity of title compound was determined, the results showed the title compound displayed moderate fungicidal activity against G. zeae Petch, Phytophthora infestans (Mont.) de Bary, Botryosphaeria berengeriana f. sp. piricola (Nose) koganezawa et Sakuma, Fusarium oxysporum f.sp. cucumerinum, and Cercospora arachidicola.     

The structure of dehydrated (Li<Subscript>0.7</Subscript>Na<Subscript>0.3</Subscript>)-analcime: Trigonal deformation of the ANA framework and new low coordinated non-framework positions

The dehydrated form of (Li,Na)-substituted analcime, Li_1.30Na_0.53[Al_1.83Si_4.17O₁₂], has been prepared and investigated with single crystal X-ray diffraction: a = 32.167(6) Å, b = 18.551(2) Å, c = 11.693(2) Å; β = 90.06(1)°, V = 6978(1) ų, Z = 24, space group C2. The structure was analyzed through considering the aluminosilicate framework as a system of tubes composed from corrugated 6-membered rings joint by triples of tetrahedra. Volume decrease by 6.5% and trigonal distortion of the structure are explained by the localization of the non-framework cations in new unusual positions. On dehydration of Li, Na-analcime, 67% of Na⁺ and 20% of Li⁺ migrated from the standard M-positions at the periphery of the tubes into essentially different positions Na^W and Li^L situated on the axes of the tubes. Among the total of the fixed tube positions— 12Na^W and 16Li^L — one half is aggregated in the tubes parallel to [001] and has a planar three-fold coordination by framework O-atoms. The configuration and cation population of the tubes in other directions follow the motif of the “basic” system.     

Synthesis and Characterization of a Novel 3D Organic–Inorganic Hybrid Framwork Templated by Keggin Anions

A novel 3D compound, {K₃H₂[Cu(Gly)₂]₃BW₁₂O₄₀}·10H₂O 1 (Gly = glycine), has been synthesized and characterized by elemental analyses, IR, TG analyses, cyclic voltammetry, and single-crystal X-ray diffraction. Compound 1 contains square-grid layers constructed by potassium cations and copper-glycine coordination complexes, the [BW₁₂O₄₀]^4? anions as templates are accommodated in the square grids by connecting with the K atoms. The K atoms link [BW₁₂O₄₀]^4? anions from different layers together to yield a 3D novel structure. The crystal data for compounds 1: monoclinic, space group p2(1)/n, a = 18.832(4) Å, b = 16.488(3) Å, c = 20.570(4) Å, β = 106.21(3)°, V = 6133(2) Å³, Z = 4.     

New hybrids of clozapine and haloperidol and their isosteric analogues: synthesis,X-ray crystallography,conformational analysis and preliminary pharmacological evaluation

Schizophrenia is a debilitating mental disorder which affects approximately 1% of the world’s population. Clozapine is an atypical antipsychotic showing unmatched effectiveness in the control of treatment-resistant schizophrenia. Unlike typical antipsychotics, clozapine does not induce extrapyramidal side effects (EPS), tardive dyskinesia or elevate prolactin levels. However, clozapine can induce a potentially fatal blood disorder, agranulocytosis, in 1–2% of patients, severely limiting its clinical use. The model for antipsychotic activity under investigation is based on obtaining a clozapine-like profile with preferential dopamine D₄ and serotonin 5-HT_2A receptor affinity. Profiled herein are three unique members of a series of prospective antipsychotic agents. Compound (I) originated from the structural hybridization of the commercial therapeutics, clozapine and haloperidol, whilst compounds (II) and (III) possess an alternative tricyclic nucleus derived from JL13; a clozapine-like atypical antipsychotic developed by Liégeois et al. These compounds have been synthesized and characterized by means of elemental analysis, IR, ¹H and ¹³C-NMR spectroscopy, MS and X-ray diffraction. Compound (I) crystallizes in space group P(?1) with a = 10.5032(1), b = 10.6261(2), c = 12.6214(3) Å, α = 81.432(1)°, β = 83.292(1)°, γ = 61.604(1)°, Z = 2, V = 1223.62(4) Å³, C₂₈H₂₉ClN₄O, M _r = 473.00, D _c = 1.284 Mg/m³, μ = 0.185 mm^?1, F(000) = 500, R = 0.0506 and wR = 0.1304. Compound (II) crystallizes in the monoclinic space group P2₁/c with a = 10.8212(2), b = 9.3592(2), c = 22.9494(5) Å, β = 106.471(1)°, Z = 4, V = 2228.88(8) Å³, C₂₅H₂₅ClN₄O₂, M _r = 448.94, D _c = 1.338 Mg/m³, μ = 0.202 mm^?1, F(000) = 944, R = 0.0529 and wR = 0.1129. Compound (III) crystallizes in the monoclinic space group P2₁/c with a = 10.5174(2), b = 9.3112(2), c = 24.2949(5) Å, β = 98.666(1)°, Z = 4, V = 2352.03(8) Å³, C₂₅H₂₄Cl₂N₄O₂, M _r = 483.38, D _c = 1.365 Mg/m³, μ = 0.306 mm^?1, F(000) = 1008, R = 0.0478 and wR = 0.1067. The solid state conformations of (I), (II) and (III) exhibit the characteristic V-shaped buckled nature of the respective dibenzodiazepine and pyridobenzoxazepine nuclei with the central seven-membered heterocycle in a boat conformation. The molecules of (I) form a head-to-tail dimeric motif stabilized by hydrogen bonding. The results of a conformational analysis of compounds (I)–(III) investigating the effect of environment (in vacuo and aqueous solution) are presented. These analogues were tested for in vitro affinity for the dopamine D₄ and serotonin 5-HT_2A receptors and their comparative receptor binding profiles to clozapine and JL13 are reported.     

Synthesis and characterization of high-dimensional structure based on paradodecatungstate clusters and sodium–aminoacetic acid complex subunits

An organic–inorganic hybrid material based on paradodecatungstate building blocks and sodium–aminoacetic acid complex subunits,{Na₁₀(H₃N–CH₂–COO)₂[H₂W₁₂O₄₂]}·28H₂O (1), have been synthesized under mildly acidic conditions. This compound was characterized by single-crystal X-ray diffraction, elemental analysis, IR and UV–visible spectroscopies, and cyclic voltammetry. The compound crystallizes in the triclinic space group P-1 with a = 11.879(2) Å, b = 12.706(2) Å, c = 13.067(2) Å, α = 74.11(3)°, β = 79.71(3)°, γ = 65.95(3)°, V = 1727.2(5) Å³, and Z = 1. The crystal structure consists of infinite 2D layers constructed from [H₂W₁₂O₄₂]^10? clusters and sodium–aminoacetic acid complexes; adjacent layers are further joined by the complex units and sodium cations to yield a three-dimensional network.     

Structure and thermal decomposition of Cs<Subscript>2</Subscript>HPO<Subscript>4</Subscript> · 2H<Subscript>2</Subscript>O

The thermal transformations of disubstituted cesium orthophosphate crystal hydrate under heating in air up to 400°C have been studied. The dehydration process occurs in two stages with the loss of 0.6 water molecules at 60?100°C and 1.4 water molecules at 100?160°C. Anhydrous Cs₂HPO₄ is stable up to 300°C and is completely converted into cesium pyrophosphate Cs₄P₂O₇ at 330°C. The structure of Cs₂HPO₄ · 2H₂O has been determined. The compound crystallizes in monoclinic space group P2₁/c and has the unit cell parameters a = 7.4761(5) Å, b = 14.2125(8) Å, c = 7.9603(6) Å, β = 116.914(5)°, V = 754.20(9) ų, and Z = 4 at?123°C. An earlier unknown polymorph of Cs₄P₂O₇ has been found. According to X-ray powder diffraction data, hexagonal space group Р6₃ has been proposed for the formed pyrophosphate.     

Tetramminenickel hydrogen hexamolybdometalates(III)

Tetramminenickel hydrogen hexamolybdoaluminate and hexamolybdogallate(III) of compositions [Ni(NH₃)₄] · H[AlMo₆O₁₈(OH)₆] · 10H₂O (I) and [Ni(NH₃)₄] · H[GaMo₆O₁₈(OH)₆] · 10H₂O (II) were synthesized and characterized by mass spectrometry, thermogravimetry, X-ray powder diffraction, and IR spectroscopy. Their crystals are triclinic. For compound I, a= 17.30 Å, b= 14.69 Å, c= 10.45 Å, α = 129.07, β = 65.91°, γ = 138.01°, V = 1338.7l ų, ρ_calcd = 2.75g/cm³, Z = 2; for compound II, a = 17.38 Å, b= 14.75 Å, c= 10.51 Å, α = 131.38°, β= 65.96°, γ = 138.09, V = 1338.15 ų, ρ_calcd = 2.68 g/cm³, Z = 2.     

Solubility of B-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> and the Hydrolysis of Niobium(V) in Aqueous Solution as a Function of Temperature and Ionic Strength

B-Nb₂O₅ was recrystallized from commercially available oxide, and XRD analyses indicated that it is stable in contact with solutions over the pH range 0 to 9, whereas solid polyniobates such as Na₈Nb₆O₁₉?13H₂O(s) appear to predominate at pH>9. Solubilities of the crystalline B-Nb₂O₅ were determined in five NaClO₄ solutions (0.1≤I _m /mol?kg^?1≤1.0) over a wide pH range at (25.0±0.1)?°C and at 0.1 MPa. A limited number of measurements were also made at I _m =6.0 mol?kg^?1, whereas at I _m =1.0 mol?kg^?1 the full range of pH was also covered at (10, 50 and 70)?°C. The pH of these solutions was fixed using either HClO₄ (pH≤4) or NaOH (pH≥10) and determined by mass balance, whereas the pH on the molality scale was measured in buffer mixtures of acetic acid?+?acetate (4≤pH≤6), Bis-Tris (pH≈7), Tris (pH≈8) and boric acid?+?borate (pH≈9). Treatment of the solubility results indicated the presence of four species, \(\mathrm{Nb(OH)}_{n}^{5-n}\) (where n=4–7), so that the molal solubility quotients were determined according to:

$0\mathrm{.5Nb}_{2}\mathrm{O}_{5}\mathrm{(cr)+0}\mathrm{.5(2}n-5\mathrm{)H}_{2}\mathrm{O(l)}_{\leftarrow}^{\to}\mathrm{Nb(OH)}_{n}^{5-n}+(n-5)\mathrm{H}^{+}\quad (n=4\mbox{--}7)$

and were fitted empirically as a function of ionic strength and temperature, including the appropriate Debye-Hückel term. A Specific Interaction Theory (SIT) approach was also attempted. The former approach yielded the following values of log?₁₀ K _sn (infinite dilution) at 25?°C: ?(7.4±0.2) for n=4; ?(9.1±0.1) for n=5; ?(14.1±0.3) for n=6; and ?(23.9±0.6) for n=7. Given the experimental uncertainties (2σ), it is interesting to note that the effect of ionic strength only exceeded the combined uncertainties significantly in the case of log?₁₀ K _s6 to I _m =1.0 mol?kg^?1, such that these values may be of use by defining their magnitudes in other media. Values of Δ _f G ^o, Δ _f H ^o, S ^o and \(C_{p}^{\mathrm{o}}\) (298.15 K, 0.1 MPa) for each hydrolysis product were calculated and tabulated.

     

Crystal structures of Ti(NH<Subscript>4</Subscript>)<Subscript>2</Subscript>P<Subscript>4</Subscript>O<Subscript>13</Subscript> and Sn(NH<Subscript>4</Subscript>)<Subscript>2</Subscript>P<Subscript>4</Subscript>O<Subscript>13</Subscript>

The characteristics of crystal structures of the titanium(IV) diammonium (Ti(NH₄)₂P₄O₁₃) and tin(IV) diammonium (Sn(NH₄)₂P₄O₁₃) tetraphosphates, which are isostructural with similar silicon(IV) and germanium(IV) salts, have been obtained by the Rietveld method using X-ray powder diffraction data. The compounds crystallize in the triclinic system, space group P \(\overline 1 \), Z = 2, a = 15.0291(7) Å, b = 7.9236(4) Å, c = 5.0754(3) Å, α = 99.168(3)°, β = 97.059(3)°, γ = 83.459(3)° for Ti(NH₄)₂P₄O₁₃ and a = 15.1454(7) Å, b = 8.0103(5) Å, c = 5.1053(3) Å, α = 99.898(6)°, β = 96.806(3)°, γ = 83.881(4)° for Sn(NH₄)₂P₄O₁₃. The structure is refined in the isotropic approximation using the pseudo-Voigt function: R _p = 0.077, R _Bragg = 0.045, R _F = 0.057 for Ti(NH₄)₂P₄O₁₃; R _p = 0.082, R _Bragg = 0.044, R _F = 0.046 for Sn(NH₄)₂P₄O₁₃. The hydrogen atoms of the ammonium cations are placed in the calculated positions. A comparative analysis of the structures of the compounds of the M^IV(NH₄)₂P₄O₁₃ (M^IV = Si, Ge, Ti, Sn) series has been carried out.