Preparation, characterization and electrochemical performance of γ-MnO2 and LiMn2O4 as cathodes for lithium batteries

The spinel LiMn₂O₄ is a very promising cathode material with economical and environmental advantages. LiMn₂O₄ materials have been synthesized by solid state method using γ-MnO₂ as manganese source, and Li₂CO₃ or LiNO₃ as Li sources. γ-MnO₂ is a commercial battery grade electrolytic manganese dioxide (TOSOH-Hellas GH-S) and LiMn₂O₄ samples were synthesized at a calcinations temperature up to 800 °C. γ-MnO₂ and LiMn₂O₄ samples were characterized by X-ray diffraction, thermal and electrochemical measurements. X-ray powder diffraction of as prepared LiMn₂O₄ showed a well-defined highly pure spinel single phase. The electrochemical performance of LiMn₂O₄ and its starting material γ-MnO₂ was evaluated through cyclic voltammetry, galvanostatic (constant current charge-discharge cycling) The electrochemical properties in terms of cycle performance were also discussed. γ-MnO₂ showed fairly high initial capacity of about 200 mAhg⁻¹ but poor cycle performance. LiMn₂O₄ samples showed fairly low initial capacity but good cycle performance.     

Anchoring alpha-manganese oxide nanocrystallites on multi-walled carbon nanotubes as electrode materials for supercapacitor

The partial coverage of manganese oxide (MnO₂) particles was achieved on the surfaces of multi-walled carbon nanotubes (MWCNTs) through a facile hydrothermal process. These particles were demonstrated to be alpha-manganese dioxide (α-MnO₂) nanocrystallites, and exhibited the appearance of the whisker-shaped crystals with the length of 80–100 nm. In such a configuration, the uncovered CNTs in the nanocomposite acted as a good conductive pathway and the whisker-shaped MnO₂ nanocrystallites efficiently increased the contact of the electrolyte with the active materials. Thus, the highest specific capacitance of 550 F g⁻¹ was achieved using the resulting nanocomposites as the supercapacitor electrode. In addition, the enhancement of the capacity retention was observed, with the nanocomposite losing only 10% of the maximum capacity after 1,500 cycles.     

A novel method for preparing lithium manganese oxide nanorods from nanorod precursor

Lithium manganese oxide nanorods were prepared from manganese dioxide nanorods precursor. The structure and morphology were confirmed by X-ray diffraction (XRD) and transmission electron microscope (TEM). The data of the Rietveld refinement indicate that the nanorods preferentially grow along the [111] direction. After charge–discharge test at 1.0 mA cm⁻² in 3.0–4.4 V, the nanorods LiMn₂O₄ showed the 134.5 mAh g⁻¹ initial discharge capacity and only lost 1.1% of initial capacity after 30 cycles, which is better than that of bulk particles LiMn₂O₄ prepared by traditional solid-state reaction method. This effective and simple route to synthesis nanorods LiMn₂O₄ from one-dimensional (1D) precursor could also be extended to prepare 1D other nanomaterials with special electrochemical properties.     

Synthesis and characterisation of new nanostructured manganese oxides for lithium batteries

A variety of new Co-substituted and Al-substituted manganese dioxide materials, having various structures, and various morphologies with nanosize crystals have been prepared by the electrochemical-hydrothermal method. The results of structural and physico-chemical characterizations are presented by comparison to non substituted MnO₂ compounds. The substitution leads to nanostructured deposits with different morphologies and much larger surface areas. Intrinsic electrochemical Li insertion properties of these new substituted γ-MnO₂ materials are also reported. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14 – 18, 2004.     

Rational synthesis of α-MnO2 and γ-Mn2O3 nanowires with the electrochemical characterization of α-MnO2 nanowires for supercapacitor

An acidification-hydrothermal method was developed to synthesize α-MnO₂ nanowires, which was subsequently treated with ethanol, resulting in γ-Mn₂O₃ nanowire bundles on a large scale. The electrochemical characterization was carried out by cyclic voltammetry, which indicated that the α-MnO₂ nanowires in 0.5 mol L⁻¹ Na₂SO₄ aqueous electrolyte was of an excellent electrode material for supercapacitor at the scan rate of 10 mV S⁻¹ in the range of 0.0-0.85 V.     

Low thermal expansion behavior and transport properties of Ni and Ge co-doped manganese nitride materials at cryogenic temperatures

A series of Ni and Ge co-doped manganese nitride materials were fabricated by mechanical ball milling followed by solid-state sintering. Their thermal expansion properties and electrical and thermal conductivities were investigated in the temperature range of 77–300 K. The results show that Ni and Ge co-doped manganese nitride materials have negative thermal expansion (NTE), and the operation-temperature window of NTE shifts toward the lower temperature region and the variation of linear thermal expansion (ΔL/L _(300K)) in the operation-temperature window of NTE decreases with increasing Ni content. The combination of these two factors results in a low coefficient of thermal expansion (CTE) at cryogenic temperatures. The average CTE of Mn₃(Cu_0.2Ni_0.4Ge_0.4)N drops to ‘zero’ in the temperature range of 190–77 K. The values of electrical and thermal conductivities of the Ni and Ge co-doped manganese nitride materials are in the ranges of 2–3×10³ (ohm cm)⁻¹ and 1.6–3.4 W (m K)⁻¹, respectively.     

Protonic batteries based on chemically synthesized MnO2

Synthesis temperature, during air-oxidation of manganese hydroxide, of γ-MnO₂ influences performance of the protonic solid-state battery. X-ray powder diffraction analyses reveal a high degree of De Wolff disorder in samples synthesized at 40 and 60 °C, resulting in poor battery performance. The discharge profile of cell with proton-conducting solid electrolyte and composite zinc as anode, recorded at a constant load condition, indicates proton intercalation. MnO₂ synthesized at 80 °C exhibits improved battery performance.     

Fluorescent Method for the Determination of Sulfide Anion with ZnS:Mn Quantum Dots

Water-soluble Mn²⁺-doped ZnS quantum dots (QDs) were prepared using mercaptoacetic acid as the stabilizer. The optical properties and structure features were characterized by X-Ray, absorption spectrum, IR spectrum and fluorescence spectrum. In pH 7.8 Tris-HCl buffer, the QDs emitted strong fluorescence peaked at 590 nm with excitation wavelength at 300 nm. The presence of sulfide anion resulted in the quenching of fluorescence and the intensity decrease was proportional to the S²⁻ concentration. The linear range was from 2.5 × 10⁻⁶ to 3.8 × 10⁻⁵ mol L⁻¹ with detection limit as 1.5 × 10⁻⁷ mol L⁻¹. Most anions such as F⁻, Cl⁻, Br⁻, I⁻, CH₃CO₂ ⁻, ClO₄ ⁻, CO₃ ²⁻, NO₂ ⁻, NO₃ ⁻, S₂O₃ ²⁻, SO₃ ²⁻ and SO₄ ²⁻ did not interfere with the determination. Thus a highly selective assay was proposed and applied to the determination of S²⁻ in discharged water with the recovery of ca. 103%.     

Study of Enhanced Chemiluminescence of Diperiodatocuprate (III) on 1,10-Phenanthroline/Hydrogen Peroxide/Cetyltrimethylammonium Bromide System

In the paper, a chemiluminescence (CL) system was developed based on the catalytical effect of diperiodatocuprate (III) (DPC) on the 1,10-phenanthroline (phen)/hydrogen peroxide (H₂O₂) in the presence of cetyltrimethylammonium bromide (CTAB). The effects of experimental conditions were investigated. Meanwhile the increase of CL intensity of the DPC/phen/H₂O₂/CTAB system is proportional to the concentration of phen in the range of low concentration. The linear range of the calibration curve is 5.0 × 10⁻⁹–1.0 × 10⁻⁶ mol L⁻¹, and the corresponding detection limit is 1.9 × 10⁻⁹ mol L⁻¹. The effects of phenolic compounds (PCs) on the system were investigated. Hydroquinone was used as an example to investigate the application of the CL system to the determination of PCs. The quenched CL intensity is linearly related to the logarithm of concentration of hydroquinone. The linear range of the calibration curve is 2.5 × 10⁻⁹–1.0 × 10⁻⁵ g mL⁻¹, and the corresponding detection limit is 1.8 × 10⁻⁹ g mL⁻¹. This phen and hydroquinone can be synchronously determined. The method was applied to the determination of hydroquinone in water samples and the recoveries were from 92% to 106%.     

Cilostazol determination by the enhancement of the green emission of Tb3+ optical sensor

The efficiency of excited-state interaction between Tb³⁺ and the industrial product Cilostazol (CIL) has been studied in different solvents. High luminescence intensity peak at 545 nm of terbium complex in acetonitrile was obtained. The photophysical properties of the green emissive Tb³⁺ complex have been elucidated, the terbium was used as optical sensor for the assessment of CIL in the pharmaceutical tablets and body fluids at pH 3.1 and λ_ex = 320 nm with a concentration range 1.0 × 10⁻⁹–1.0 × 10⁻⁶ mol L⁻¹ of CIL, correlation coefficient of 0.998 and detection limit of 7.5 × 10⁻¹⁰ mol L⁻¹.     

Preparation of MnO<Subscript>2</Subscript>/WMNT composite and MnO<Subscript>2</Subscript>/AB composite by redox deposition method and its comparative study as supercapacitive materials

The manganese oxide/multi-walled carbon nanotube (MnO₂/MWNT) composite and the manganese oxide/acetylene black (MnO₂/AB) composite were prepared by translating potassium permanganate into MnO₂ which formed the above composite with residual carbon material using the redox deposition method and carbon as a reducer. The products were characterized by X-ray diffraction, Fourier transform infrared, and scanning electron microscope. Electrochemical properties of both the MnO₂/MWNT and MnO₂/AB electrodes were studied by using cyclic voltammetry, electrochemical impedance measurement, and galvanostatic charge/discharge tests. The results show that the MnO₂/MWNT electrode has better electrochemical capacitance performance than the MnO₂/AB electrode. The charge–discharge test showed the specific capacitance of 182.3 F·g⁻¹ for the MnO₂/MWNT electrode, and the specific capacitance of 127.2 F·g⁻¹ for the MnO₂/AB electrode had obtained, within potential range of 0–1 V at a charge/discharge current density of 200 mA·g⁻¹ in 0.5 mol·L⁻¹ potassium sulfate electrolyte solution in the first cycle. The specific capacitance of both the MnO₂/MWNT and MnO₂/AB electrodes were 141.2 F·g⁻¹ and 78.5 F·g⁻¹ after 1,200 cycles, respectively. The MnO₂/MWNT electrode has better cycling performance. The effect of different morphologies was investigated for both MnO₂/MWNT and MnO₂/AB composites.     

Spectrofluorimetric Assessment of Hydrochlorothiazide Using Optical Sensor Nano-Composite Terbium Ion Doped in Sol-Gel Matrix

A new, simple, sensitive and selective spectrofluorimetric method for the determination of Hydrochlorothiazide was developed in acetonitrile at pH 6.2. The Hydrochlorothiazide can remarkably enhance the luminescence intensity of the Tb³⁺ ion doped in sol–gel matrix at λ_ex = 370 nm. The intensity of the emission band of Tb³⁺ ion doped in sol–gel matrix was increased due to the energy transfer from the triplet excited state of Hydrochlorothiazide to (⁵D₄) excited energy state of Tb³ ion. The enhancement of the emission band of Tb³⁺ ion doped in sol–gel matrix at (⁵D₄→⁷ F₅) 545 nm was directly proportion to the concentration of Hydrochlorothiazide with a dynamic ranges of 5.0 × 10⁻¹⁰—5.0 × 10⁻⁶ mol L⁻¹ and detection limit of 2.2 × 10⁻¹¹ mol L⁻¹.     

The influence of hydrogen plasma pre-treatment on the structure of BDND electrode surface applied for phenol detection

The surface properties of boron-doped nanocrystalline diamond films treated with H₂ plasma was investigated in regard to their electrochemical response for phenol oxidation. The surface of these films is relatively flat formed by crystallites with sizes of about 40 nm. X-ray photoelectron spectroscopy analyses showed that electrode surface has a high amount of C–H bonds. This behavior is in agreement with Mott-Schottky plot measurements concerning the flat band potential that presented a value as expected for hydrogenated diamond surface. This electrode presented the phenol detection limit of 0.08 mg L⁻¹ for low phenol concentrations from 40 to 250 μmol L⁻¹.     

An ionic liquid-type multiwall carbon nanotubes paste electrode for electrochemical investigation and determination of morphine

The direct electrochemistry of morphine on modified multiwall carbon nanotubes using carbon ionic liquid (i.e., 1-butyl-3-methylimidazolium hexafluoro phosphate, ([C4mim]–[PF6])) was studied. It was found that the electrode showed sensitive voltammetric response to morphine. The experimental results suggested that the modified electrode promoted electron transfer reaction for the oxidation of morphine. The electron transfer coefficient and charge transfer resistant (R _ct) of morphine at the modified electrode were calculated. Under the optimized conditions at pH 8.0, the peak current was linear to morphine concentrations over the concentration range of 0.45–450 μmol L⁻¹, using differential pulse voltammetry. The detection limit was 0.14 μmol L⁻¹. The proposed method was successfully applied to the determination of morphine in both ampoules and urine samples.     

Structural and ionic conductivity studies on P(ECH-EO):γ-BL:LiClO<Subscript>4</Subscript> plasticized polymer electrolyte

The plasticized polymer electrolyte consisting of poly(epichlorohydrin-ethyleneoxide) [P(ECH-EO)], lithium perchlorate (LiClO₄) and γ-butyrolactone (γ-BL) have been prepared by simple solution casting technique. The polymer–salt–plasticizer complex has been confirmed by XRD analysis. The ionic conductivity studies have been carried out using AC impedance technique. The effect of plasticizer (γ-BL) on ionic conductivity has been discussed with respect to different temperatures. The maximum value of ionic conductivity is found to be 1.3 × 10⁻⁴ Scm⁻¹ for 70P(ECH-EO):15γ-BL:15LiClO₄ at 303 K. The temperature dependence of the plasticized polymer electrolyte follows the Vogel–Tamman–Fulcher formalism. The activation energy is found to decrease with the increase in plasticizer.     

Plasma-electrolytic formation, composition and catalytic activity of manganese oxide containing structures on titanium

In the present work, we report the data about formation of TiO₂-rutile or TiO₂ and Mn₂O₃, Mn₃O₄ containing oxide structures on titanium in aqueous electrolytes by means of plasma-electrolytic deposition. The layers formed are characterized by X-ray diffraction, electron probe microanalysis and scanning electron microscopy methods. The PEO coatings on titanium formed in sodium tetraborate solution contain the TiO₂ stabile rutile modification that is important when utilizing such a structure as a catalyst carrier. Manganese acetate adding into the electrolyte leads to formation of layers that contain Mn₂O₃, Mn₃O₄ and TiO₂-rutile in outer region. The manganese content in the surface layer depends on the formation conditions as well as on manganese acetate concentration in the electrolyte. Catalytic activity of the layers in CO → CO₂ reaction is studied in the static and flow conditions. The manganese-containing layers obtained possess the catalytic activity in CO → CO₂ oxidation reaction at the temperature range of 250-350 °C. The catalytic activity depends on the concentration and surface distribution of manganese as well as on the layers morphology.     

Fluorescence and Electrochemical Sensing of Pesticides Methomyl, Aldicarb and Prometryne by the Luminescent Europium-3-Carboxycoumarin Probe

This work describes the application of time resolved fluorescence in microtiterplates and electrochemical methods on glassy carbon electrode for investigating the interactions of europium-3-carboxycoumarin with pesticides aldicarb, methomyl and prometryne. Stern-volmer studies at different temperatures indicate that static quenching dominates for methomyl, aldicarb and prometryne. By using Lineweaver-Burk equation binding constants were determined at 303 K, 308 K and 313 K. A thermodynamic analysis showed that the reaction is spontaneous with ΔG being negative. The enthalpy ΔH and the entropy ΔS of reactions were all determined. A time-resolved (gated) luminescence-based method for determination of pesticides in microtiterplate format using the long-lived europium-3-carboxycoumarin has been developed. The limit of detection is 4.80, 5.06 and 8.01 μmol L⁻¹ for methomyl, prometryne and aldicarb, respectively. This is the lowest limit of detection achieved so far for luminescent lanthanide-based probes for pesticides. The interaction of the probe with the pesticides has been investigated using cyclic voltammetry (CV), differential pulse polarography (DPP), square wave voltammetry (SWV) and linear sweep voltammetry (LSV) on a glassy carbon electrode in I = 0.1 mol L⁻¹ p-toluenesulfonate at 25 °C. The diffusion coefficients of the reduced species are calculated. The main properties of the electrode reaction occurring in a finite diffusion space are the quasireversible maximum and the splitting of the net SWV peak for Eu(III) ions in the ternary complex formed . It was observed that the increase of the cathodic peak currents using LSV is linear with the increase of pesticides concentration in the range 5 × 10⁻⁷ to 1 × 10⁻⁵ mol L⁻¹. The detection limit (DL) were about 1.01, 2.23 and 1.89 μmolL⁻¹ for aldicarb, methomyl and prometryne, respectively. In order to assess the analytical applicability of the method, the influence of various potentially interfering species was examined. Influence of interfering species on the recovery of 10 μmol L⁻¹ pesticides has been investigated.     

Facile route to control the surface morphologies of 3D hierarchical MnO<Subscript>2</Subscript> and its Al self-doping phenomenon

In this article, a catalytic-ion assisted hydrothermal method has recently been developed for synthesis of hierarchical manganese dioxide nanostructures. In this study, various shapes of hierarchical MnO₂ (nanorod, nanothorn sphere, sphere) were successfully synthesized using the hydrothermal method with quantitative control of Al³⁺ in solution. The aspect ratio of aligned nanorods on the nanothorn sphere was easily controlled by the amount of Al³⁺ in the MnSO₄ and (NH₄)₂S₂O₈ aqueous solution. Furthermore, we found that Al³⁺ species in the solution acted as a functional doping species into 2 × 2 tunnels of α-MnO₂ and also as a catalyst. The formation mechanism of hierarchical MnO₂ structures as a function of Al³⁺ concentration during hydrothermal reaction was sufficiently investigated, and the role of Al³⁺ as catalyst and doping species in the solution was discussed.     

Investigation of electrochemical performance of sol-gel derived MgFe2O4 nanospheres as aqueous supercapacitor electrode and bi-functional water splitting electrocatalyst in alkaline medium

Herein this work, we have used the sol-gel chemical synthesis method to prepare spherical shaped MgFe₂O₄ nanoparticles having size 45–50 nm. Using 1 mol L⁻¹ Sodium Perchlorate (NaClO₄) electrolyte, a capacitance of 61 F/g, a capacitance retention of 82.91% (after undergoing 1000 cycles), and an energy density of 41 Wh/kg have been achieved. Using 1 mol L⁻¹ Magnesium Perchlorate (Mg(ClO₄)₂) as electrolyte, a capacitance of 43 F/g, a capacitance retention of 82.15%, and an energy density of 29 Wh/kg have been realized. Furthermore, MgFe₂O₄ nanospheres exhibited an overpotential (η) = 1.09 V, a Tafel slope (b) = 317 mV/dec in regard to alkaline Oxygen Evolution Reaction (OER) electrocatalyst. It also achieved η = 402 mV and b = 241 mV/dec in regard towards alkaline Hydrogen Evolution Reaction (HER) electrocatalyst. These results signify the suitability of MgFe₂O₄ nanoparticles for high energy density aqueous supercapacitor and water splitting electrocatalyst applications.     

Studies on lithium bis(oxalato)-borate/propylene carbonate-based electrolytes for Li-ion batteries

Lithium bis(oxalato)-borate (LiBOB) is a promising salt for Li-ion batteries owing to its various characteristics such as non-fluorine, non-toxicity, low cost, and safety. It has the unique merits such as the stability at high temperature and the film-forming characteristics in propylene carbonate (PC)-based electrolyte. In this work, the utilization of PC as the basal solvent and dimethyl carbonate, γ-butyrolactone and ethylene carbonate as co-solvents for LiBOB have been investigated. The results indicate that the co-solvent has conducive effects on the conductivities, viscosities, and battery performance. The conductivity and viscosity of 0.7 mol L⁻¹ LiBOB in PC+GBL+EC+DMC (1:1:1:1, v/v) are 6.22 mS cm⁻¹ and 3.74 mPa s, respectively, and it is very stable in 0–5 V range. The capacity of Li/LiFePO₄ battery is about 160 mAh g⁻¹ at 0.5 °C. Moreover, the battery has exhibited the excellent rate performance.