Electrogenerated chemiluminescence biosensing for the detection of prostate PC-3 cancer cells incorporating antibody as capture probe and ruthenium complex-labelled wheat germ agglutinin as signal probe

A highly selective and sensitive electrogenerated chemiluminescence (ECL) biosensor for the detection of prostate PC-3 cancer cells was designed using a prostate specific antibody as a capture probe and ruthenium complex-labelled wheat germ agglutinin as a signal probe. The ECL biosensor was fabricated by covalently immobilising the capture probe on a graphene oxide-coated glassy carbon electrode. Target PC-3 cells were selectively captured on the surface of the biosensor, and then, the signal probe was bound with the captured PC-3 cells to form a sandwich. In the presence of tripropylamine, the ECL intensity of the sandwich biosensor was logarithmically directly proportion to the concentration of PC-3 cells over a range from 7.0 × 10² to 3.0 × 10⁴ cells mL⁻¹, with a detection limit of 2.6 × 10² cells mL⁻¹. The ECL biosensor was also applied to detect prostate specific antigen with a detection limit of 0.1 ng mL⁻¹. The high selectivity of the biosensor was demonstrated in comparison with that of a lectin-based biosensor. The strategy developed in this study may be a promising approach and could be extended to the design of ECL biosensors for highly sensitive and selective detection of other cancer-related cells or cancer biomarkers using different probes.     

Analysis of Strychnos alkaloids in traditional Chinese medicines with improved sensitivity by sweeping micellar electrokinetic chromatography

A new amperometric method was developed for rapid detection of Escherichia coli (E. coli) density using a bienzyme biosensor. The bienzyme biosensor was fabricated based on the covalent immobilization of laccase and horseradish peroxidase (HRP) at indium tin oxide (ITO) electrode by (3-aminopropyl) triethoxysilane (APTES) monolayer. The bienzyme biosensor showed a high sensitivity in determination of the polyphenolic compounds, which was microbially generated from the salicylic acid (SA) added into the culture medium during the course of E. coli metabolism. Since the amount of polyphenolic compounds depends on E. coli density, the bienzyme biosensor was applied for the rapid and high sensitive detection of E. coli density after the E. coli solution was incubated in culture medium with salicylic acid for 2.5 h at 37 °C. By chronoamperometry, the amplified response current was obtained at the bienzyme biosensor, due to the substrate recycling of the polyphenolic compounds driven by bienzyme-catalyzed oxidation and electrochemical reduction. The amplified response current at the biosensor was linear with the E. coli density ranging from 1.6 × 10³ to 1.0 × 10⁷ cells/mL. The bienzyme biosensor could detect the E. coli density with a detection limit of 9.7 × 10² cells/mL within 3 h.     

Detection of P. aeruginosa using nano-structured electrode-separated piezoelectric DNA biosensor

A DNA biosensor for detection of Pseudomonas aeruginosa was set up based on the modification of two membranes (nano-TiO₂ and nano-TiO₂-polyethylene glycol hybrid membrane) to the ESPS surface. These two membrane materials were synthesized by sol-gel method. The detection was accomplished by modifying ss-DNA on the sensitive membrane and then hybridizing with their complementary strands from the P. aeruginosa in liquid phase. UV spectrum was used to identify the purity and concentration of extracted DNA; IR spectrum and SEM were used to characterize the properties of the membrane. The detection was highly improved by adoption of nanotechnology and hybrid membrane. Less than 3 h was sufficient. The detection linear range was from 10⁻¹ to 10⁻³ g l⁻¹ and the limit of detection was 10⁻⁴ g l⁻¹.     

Electrochemiluminescence biosensor for the assay of small molecule and protein based on bifunctional aptamer and chemiluminescent functionalized gold nanoparticles

An electrochemiluminescence (ECL) biosensor for simultaneous detection of adenosine and thrombin in one sample based on bifunctional aptamer and N-(aminobutyl)-N-(ethylisoluminol) functionalized gold nanoparticles (ABEI-AuNPs) was developed. A streptavidin coated gold nanoparticles modified electrode was utilized to immobilize biotinylated bifunctional aptamer (ATA), which consisted of adenosine and thrombin aptamer. The ATA performed as recognition element of capture probe. For adenosine detection, ABEI-AuNPs labeled hybridization probe with a partial complementary sequence of ATA reacted with ATA, leading to a strong ECL response of N-(aminobutyl)-N-(ethylisoluminol) enriched on ABEI-AuNPs. After recognition of adenosine, the hybridization probe was displaced by adenosine and ECL signal declined. The decrease of ECL signal was in proportion to the concentration of adenosine over the range of 5.0 × 10⁻¹²–5.0 × 10⁻⁹ M with a detection limit of 2.2 × 10⁻¹² M. For thrombin detection, thrombin was assembled on ATA modified electrode via aptamer–target recognition, another aptamer of thrombin tagged with ABEI-AuNPs was bounded to another reactive site of thrombin, producing ECL signals. The ECL intensity was linearly with the concentration of thrombin from 5 × 10⁻¹⁴ M to 5 × 10⁻¹⁰ M with a detection limit of 1.2 × 10⁻¹⁴ M. In the ECL biosensor, adenosine and thrombin can be detected when they coexisted in one sample and a multi-analytes assay was established. The sensitivity of the present biosensor is superior to most available aptasensors for adenosine and thrombin. The biosensor also showed good selectivity towards the targets. Being challenged in real plasma sample, the biosensor was confirmed to be a good prospect for multi-analytes assay of small molecules and proteins in biological samples.     

Amperometric choline biosensors prepared by layer-by-layer deposition of choline oxidase on the Prussian blue-modified platinum electrode

An amperometric choline biosensor was developed by immobilizing choline oxidase (ChOx) in a layer-by-layer (LBL) multilayer film on a platinum (Pt) electrode modified with Prussian blue (PB). 6-O-Ethoxytrimethylammoniochitosan chloride (EACC) was used to prepare the ChOx LBL films. The choline biosensor was used at 0.0 V versus Ag/AgCl to detect choline and exhibited good characteristics such as relative low detection limit (5 × 10⁻⁷ M), short response time (within 10 s), high sensitivity (88.6 μA mM⁻¹ cm⁻²) and a good selectivity. The results were explained based on the ultrathin nature of the LBL films and the low operating potential that could be due to the efficient catalytic reduction of H₂O₂ by PB. In addition, the effects of pH, temperature and applied potential on the amperometric response of choline biosensor were evaluated. The apparent Michaelis-Menten constant was found to be (0.083 ± 0.001) ×10⁻³ M. The biosensor showed excellent long-term storage stability, which originates from a strong adsorption of ChOx in the EACC multilayer film. When the present choline biosensor was applied to the analysis of phosphatidylcholine in serum samples, the measurement values agreed satisfactorily with those by a hospital method.     

Biosensor for chlorogenic acid based on an ionic liquid containing iridium nanoparticles and polyphenol oxidase

A biosensor based on the ionic liquid, 1-n-butyl-3-methylimidazolium hexafluorophosphate containing dispersed iridium nanoparticles (Ir-BMI.PF₆) and polyphenol oxidase was constructed. This enzyme was obtained from the sugar apple (Annona squamosa), immobilized in chitosan ionically crosslinked with oxalate. The biosensor was used for determination of chlorogenic acid by square wave voltammetry. The polyphenol oxidase catalyzes the oxidation of chlorogenic acid to the corresponding o-quinone, which is electrochemically reduced back to this substance at +0.25 V vs. Ag/AgCl. Under optimized operational conditions the chlorogenic acid concentration was linear in the range of 3.48 × 10⁻⁶ to 4.95 × 10⁻⁵ mol L⁻¹ with a detection limit of 9.15 × 10⁻⁷ mol L⁻¹. The biosensor was applied in the determination of chlorogenic acid in organic and decaffeinated coffee and the results compared with those obtained using the capillary electrophoresis method. The recovery study for chlorogenic acid in these samples gave values of 93.2-105.7%.     

On-chip integrated hydrolysis, fluorescent labeling, and electrophoretic separation utilized for acetylcholinesterase assay

A sensitive on-chip acetylcholinesterase (AChE) assay that serves as a basis for the development of a fully integrated on-chip AChE-inhibitor detection assay is presented. The sequential steps required for the on-chip analysis process were integrated into a microchip. Transport and mixing of the reagents occurred by a combination of electroosmosis and electrophoresis using computer-controlled electrokinetic transport. AChE-catalyzed hydrolysis of acetylthiocholine to thiocholine was determined by on-chip reaction of thiocholine with eosinmaleimide, and the resulting thioether was electrophoretically separated and detected by laser-induced fluorescence (LIF). Enzyme-substrate mixing and reaction by confluent flow of reagents was compared with electrophoretically mediated microanalysis (EMMA), based on injection of an enzyme plug, and the utilization of differences in electrophoretic mobility as a driving force for efficient mixing and reaction. Both methods yielded similar results, however the EMMA-plug technique is preferable. The EMMA-plug technique was optimized for length and pushing time of enzyme plug, length of dyes mixture plug, acetylthiocholine concentration, and detector location. Detection of O-ethyl S-[2-(diisopropylamino)ethyl] methylphosphonothiolate (VX) and paraoxon, two AChE inhibitors, was demonstrated by off-chip mixing of the inhibitor and AChE, followed by the on-chip AChE assay. Limit of detection of VX for 5.5 min incubation and of paraoxon for 8 min incubation was 4 × 10⁻¹⁰ and 4 × 10⁻⁷ M, respectively. Utilization of the AChE microchip assay for inhibition kinetics was demonstrated also by evaluation of the inhibitor-enzyme bimolecular reaction constant (k_i). The evaluated k_i values for VX and paraoxon for AChE from the electric eel were 3.5 × 10⁷ and 1.7 × 10⁵ M⁻¹ min⁻¹, respectively, conforming well to reported values obtained by bulk methods.     

Use of bioluminescent bacterial sensors as an alternative method for measuring heavy metals in soil extracts

The luminescence based bacterial sensor strains Pseudomonas fluorescens OS8 (pTPT11) for mercury detection and Pseudomonas fluorescens OS8 (pTPT31) for arsenite detection were used in testing their application in detecting heavy metals in soil extracts. Three different soil types (humus, mineral and clay) were spiked with 1, 100 or 500 μg g⁻¹ Hg²⁺ or As³⁺. Samples were taken 1, 14 and 30 days and extracted with water, ammonium acetate, hydrogen peroxide and nitric acid to represent water soluble, bioavailable, organic matter bound and residual fractions, respectively. The lowest mercury-concentration measured using biosensor (0.003 μg kg⁻¹) was considerably lower than by chemical method (0.05 μg kg⁻¹). The sensor strain with pTPT31 appeared to have a useful detection range similar to that of chemical methods. Concentration results with chemical and biosensor analysis were very similar in the case of mercury-spiked samples. Although some of the arsenite samples showed higher variation between methods, it is concluded that the bacteria can be used as an alternative traditional methods for different types of samples.     

A reagentless DNA biosensor based on cathodic electrochemiluminescence at a C/CxO1−x electrode

A reagentless signal-on electrochemiluminescence (ECL) biosensor for DNA hybridization detection was developed based on the quenching effect of ferrocene (Fc) on intrinsic cathodic ECL at thin oxide covered glassy carbon (C/C_xO_1−x) electrodes. To construct the DNA biosensor, molecular beacon (MB) modified with ferrocene (3′-Fc) was attached to a C/C_xO_1−x electrode via the covalent bound between labeled amino (5′-NH₂) and surface functional groups. It was found that the immobilization of the probe on the electrode surface mainly depended on the fraction of surface carbonyl moiety. When a complementary target DNA (cDNA) was present, the stem-loop of MB on the electrode was converted into a linear double-helix configuration due to hybridization, resulting in the moving away of Fc from the electrode surface, and the restoring of the cathodic ECL signal. The restoration of the ECL intensity was linearly changed with the logarithm of cDNA concentration in the range of 1.0 × 10⁻¹¹ to 7.0 × 10⁻⁸ M, and the detection limit was ca. 5.0 pM (S/N = 3). Additionally, single-base mismatched DNA can be effectively discriminated from the cDNA. The great advantage of the biosensor lies in its simplicity and cost-effective with ECL generated from the electrode itself, and no adscititious luminophore is required.     

Fabrication of a novel impedance cell sensor based on the polystyrene/polyaniline/Au nanocomposite

Gold nanoparticles (AuNPs) were assembled on the surface of polystyrene (PS) and polyaniline (PANI) core-shell nanocomposite (PS@PANI) for the immobilization of HL-60 leukemia cells to fabricate a cell electrochemical sensor. The immobilized cells exhibited irreversible voltammetric response and increased the electron transfer resistance with a good correlation to the logarithmic value of concentration ranging from 1.6 × 10³ to 1.6 × 10⁸ cells mL⁻¹ with a limit of detection of 7.3 × 10² cells mL⁻¹ at 10σ. This biosensor was simple, low cost and disposable, which implied that the PS@PANI/Au composites can regard as the potential applications for clinical applications.     

A rapid method for determining Mycobacterium tuberculosis based on a bulk acoustic wave impedance biosensor

The bulk acoustic wave impedance biosensor was set up and used to monitor the growth of Mycobacterium tuberculosis (M.TB). This sensor is rapid, simple, sensitive (lower limit is 2×10³ cells ml⁻¹) and cheap (easy to generalize). The typical response curve was different from other bacteria's, such as Escherichia coli, Staphylococcus aureus, Proteus mirabilis. The frequency detection time was used to quantitatively determine M.TB. It was proportional to logarithm of the initial concentration of M.TB in the range of 2×10³-3×10⁷ cells ml⁻¹. The set up sensor was applied to the direct diagnosis of M.TB samples. The interference of other bacteria was eliminated by pretreatment. Our results confirmed that the use of the set up biosensor was reliable, sensitive. It gives out the potential use for determining M.TB.     

Sensitive fluorimetric flow injection analysis for fluoride ion with a novel reagent, 2',7'-dichlorofluorescein di-tert-butyldimethylsilyl ether

A novel reagent, 2′,7′-dichlorofluorescein di-tert-butyldimethylsilyl ether (FCl₂TBS), was synthesized for fluoride ion and used for a sensitive fluorimetric flow injection analysis by detecting the recovery of fluorescence due to cleavage of Si-O bond. Four kinds of fluorescein di-tert-butyldimethylsilyl ether (FTBS) analogues were synthesized and FCl₂TBS was the best. By introducing chlorine to FTBS, stability of the reagent, reactivity and the baseline signals were improved. The FIA system was three lines. The sample solution (aqua medium) was injected in the carrier solution (water) and merged with the reagent solution (2.0 × 10⁻⁵ M FCl₂TBS acetone solution), then mixed with phosphate buffer solution (pH 7.5). The fluorescence intensities were measured at λ_ex 503 nm and λ_em 527 nm. The calibration graph had linear relationship between (1.0-50.0) × 10⁻⁶ M and the determinable limit was 1.0 × 10⁻⁶ M. The relative standard deviation of 12 measurements with 1.0 × 10⁻⁵ M F⁻ solution was 1.0% and the sample throughput was 13 h⁻¹. The developed method was successfully applied to river and tap water samples.     

A new amperometric bienzymatic biosensor based on biocomposites for the determination of gluconic acid in wines

A new amperometric bienzymatic biosensor for gluconic acid based on the coimmobilization of gluconokinase (EC 2.7.1.12) and phosphogluconate dehydrogenase (EC 1.1.1.44) by polysulfone membrane entrapment onto the surface of a graphite-epoxy composite is reported. This biosensor represents an alternative to gluconate dehydrogenase (EC 1.1.99.3) based methods, which is no longer commercially available. Measurements were done at an applied potential of +0.800 V, room temperature and phosphate buffer pH 7.50; obtaining a linear response range for gluconic acid extended from 7.0 × 10⁻⁶ to 2.5 × 10⁻⁴ M. Constructed biosensors showed good reproducibility for calibrations using different electrodes (RSD of 1.74%). Finally, biosensor was applied to real wine samples, and the results obtained were validated by comparison with those provided by a reference laboratory. Good correlation was found when the biosensor results were plotted vs. the reference values (slope = 1.03 ± 0.04, intercept = 0.01 ± 0.02, r² = 0.995).     

Electrochemical immunosensor designs for the determination of Staphylococcus aureus using 3,3-dithiodipropionic acid di(N-succinimidyl ester)-modified gold electrodes

The preparation of novel Staphylococcus aureus (S. aureus) amperometric immunosensing designs based on the covalent immobilization of RbIgG at gold electrodes using the heterobifunctional cross-linker 3,3-dithiodipropionic acid di(N-succinimidyl ester) (DTSP), are reported. Two different competitive immunosensing configurations have been tested and compared. In the first one, protein A-bearing S. aureus cells and HRP-labelled antiRbIgG compete for immobilized RbIgG binding sites, while in the second case HRP-labelled protein A was used. In both cases, the evaluation of the developed immunosensors performance was accomplished through the monitoring at 0.00 V (vs. Ag/AgCl) of the catalytic current originated after addition of hydrogen peroxide, using tetrathiafulvalene as redox mediator entrapped at the modified electrode surface by cross-linking with glutaraldehyde. Optimization of variables concerning the composition of the immunosensors as well as the detection conditions was carried out in 0.1 M NaAc/0.1 M NaCl buffer of pH 5.6. The configuration that employed antiRbIgG-HRP resulted in better analytical characteristics, with a detection limit of 1.4 × 10⁴ cells mL⁻¹ for S. aureus cells submitted to wall lyses by ultrasonic treatment. This immunosensor design was also evaluated using gold screen-printed electrodes in order to reduce the analysis time and cost. In this case, a limit of detection of 3.7 × 10² cells mL⁻¹ and a dynamic range from 1.3 × 10³ to 7.6 × 10⁴ cells mL⁻¹ was obtained. A RSD value of 10.5% was found for the responses to 9.6 × 10³S. aureus cells mL⁻¹ obtained with seven different Au/SPEs-immunosensors. These disposable immunosensors were applied to the quantification of S. aureus in milk spiked at two concentration levels, 1.2 × 10³ and 4.8 × 10³ cells mL⁻¹, with good recoveries.     

Total internal reflectance fluorescence (TIRF) biosensor for environmental monitoring of testosterone with commercially available immunochemistry: antibody characterization, assay development and real sample measurements

Nowadays, little technology exists that can monitor various water sources quickly and at a reasonable cost. The ultra-sensitive, fully automated and robust biosensor River Analyser (RIANA) is capable of detecting multiple organic targets rapidly and simultaneously at a heterogeneous assay format (solid phase: bulk optical glass transducers). Commercialization of such a biosensor requires the availability of commercial high-affinity recognition elements (e.g. antibodies) and suitable commercial haptens (modified target molecules) for surface chemistry. Therfore, testosterone was chosen as model analyte, which is also a task of common analytical methods like gas chromatography-mass spectrometry (GC-MS), because they have to struggle with detecting sub-nanogram per liter levels in environmental samples. The reflectometric interference spectroscopy (RIfS) was used to characterize the commercially available immunochemistry resulting in a high-affinity constant of 2.6 ± 0.3 × 10⁹ mol⁻¹ for the unlabeled antibody. After the labeling procedure, necessary for the TIRF-based biosensor, a mean affinity constant of 1.2 × 10⁹ mol⁻¹ was calculated out of RIfS (1.4 ± 0.4 × 10⁹ mol⁻¹) and TIRF (1.0 ± 0.3 × 10⁹ mol⁻¹) measurements.Thereafter, the TIRF-based biosensor setup was used to determine the steroidal hormone testosterone at real world samples without sample pre-treatment or sample pre-concentration. Results are shown for rapid and ultra-sensitive analyses of testosterone in aqueous samples with at a remarkable limit of detection (LOD) of 0.2 ng L⁻¹. All real world samples, even those containing testosterone in the sub-nanogram per liter range (e.g. 0.9 ng L⁻¹), could be determined with recovery rates between 70 and 120%. Therefore, the sensor system is perfectly suited to serve as a low-cost system for surveillance and early warning in environmental analysis in addition to the common analytical methods. For the first time, commercially available immunochemistry was fully characterized using a label-free detection method (RIfS) and successfully incorporated into a TIRF-based biosensor setup (RIANA) for reliable sub-nanogram per liter detection of testosterone in aqueous environmental samples.     

Synthesis and analytical application of a novel tetradentate N(2)O(2) Schiff base as a chromogenic reagent for determination of nickel in some natural food samples

A novel sensitive chromogenic reagent, N,N′-bis(3-methylsalicylidene)-ortho-phenylene diamine (MSOPD), has been synthesized and used in the spectrophotometric determination of nickel. At pH 8, MSOPD can react with nickel ion at room temperature to form a 1:1 complex. The apparent molar absorptivity is 9.5 × 10⁴ l mol⁻¹ cm⁻¹ at 430 nm. Beer's low is obeyed over the range 0-1.0 × 10⁻⁵ M of nickel with a detection limit of 1.36 × 10⁻⁸ M. The relative standard deviation for measurement of 3.41 × 10⁻⁶ M nickel is 1.3% (n = 10). The method has successfully been applied to determination of trace amounts of nickel in some natural food samples.     

ZnS quantum dots derived a reagentless uric acid biosensor

A reagentless amperometric uric acid biosensor based on zinc sulfide (ZnS) quantum dots (QDs) was firstly developed. It could detect uric acid without the presence of an electron mediator. The carboxyl group functionalized ZnS QDs were synthesized, and they were soluble biocompatible and conductive. ZnS QDs conjugates could provide increased enzyme binding sites, which may result in higher enzyme loading. Thus, the proposed uricase/ZnS QDs/l-cys biosensor exhibited higher amperometric response compared to the one without QDs (uricase/l-cys biosensor). In addition, there was little AA interference. It showed a linear dependence on the uric acid concentration ranging from 5.0 × 10⁻⁶ to 2.0 × 10⁻³ mol L⁻¹ with a detection limit of 2.0 × 10⁻⁶ mol L⁻¹ at 3σ.     

A novel amperometric biosensor for the detection of nitrophenol

We report on a novel amperometric biosensor for detecting phenolic compounds based on the co-immobilization of horseradish-peroxidase (HRP) and methylene blue (MB) with chitosan on Au-modified TiO₂ nanotube arrays. The titania nanotube arrays were directly grown on a Ti substrate using anodic oxidation first; a gold thin film was then coated onto the TiO₂ nanotubes by an argon plasma technique. The morphology and composition of the fabricated Au-modified TiO₂ nanotube arrays were characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Cyclic voltammetry and amperometry were used to study the proposed electrochemical biosensor. The effect of pH, applied electrode potential and the concentration of H₂O₂ on the sensitivity of the biosensor have been systemically investigated. The performance of the proposed biosensor was tested using seven different phenolic compounds, showing very high sensitivity; in particular, the linearity of the biosensor for the detection of 3-nitrophenol was observed from 3 × 10⁻⁷ to 1.2 × 10⁻⁴ M with a detection limit of 9 × 10⁻⁸ M (based on the S/N = 3).     

Electrochemiluminescent disposable cholesterol biosensor based on avidin–biotin assembling with the electroformed luminescent conducting polymer poly(luminol-biotinylated pyrrole)

An electrochemiluminescent cholesterol disposable biosensor has been prepared by the formation of assembled layers on gold screen-printed cells. The detection layer is based on the electro-formation of new luminol copolymers with different synthesized biotinylated pyrroles prepared by click-chemistry, offering a new transduction layer with new electroluminescent properties on biosensors. The electrochemiluminescence (ECL) luminol copolymers are electroformed by cyclic voltammetry (five cycles) at pH 7.0 uses a10⁻³ M biotinylated pyrrole–luminol ratio of 1:10 in PBS buffer. With respect to the recognition layer, cholesterol oxidase was biotinylated by incubation with biotin vinyl sulfone, and immobilized on the copolymer by avidin–biotin interaction. The analytical signal of the biosensor is the ECL enzymatic initial rate working in chronoamperometric mode at 0.5 V excitation potential with 10 s between pulses at pH 9.5. The disposable device offers a cholesterol linear range from 1.5 × 10⁻⁵ M to 8.0 × 10⁻⁴ M with a limit of detection of 1.47 × 10⁻⁵ M and accuracy of 7.9% for 9.0 × 10⁻⁵ M and 14.1% for 2.0 × 10⁻⁴ M, (n = 5). Satisfactory results were obtained for cholesterol determination in serum samples compared to a reference procedure.     

Integrated multienzyme electrochemical biosensors for monitoring malolactic fermentation in wines

Integrated amperometric biosensors for the determination of l-malic and l-lactic acids were developed by coimmobilization of the enzymes l-malate dehydrogenase (MDH) and diaphorase (DP), or l-lactate oxidase (LOX) and horseradish peroxidase (HRP), respectively, together with the redox mediator tetrathiafulvalene (TTF), on a 3-mercaptopropionic acid (MPA) self-assembled monolayer (SAM)-modified gold electrode by using a dialysis membrane. The electrochemical oxidation of TTF at +100 mV (vs. Ag/AgCl), and the reduction of TTF⁺ at −50 mV were used for the monitoring of the enzyme reactions involved in l-malic and l-lactic acid determinations, respectively. Experimental variables concerning the biosensors composition and the detection conditions were optimized for each biosensor. Good relative standard deviation values were obtained in both cases for the measurements carried out with the same biosensor, with no need of cleaning or pretreatment of the bioelectrodes surface, and with different biosensors constructed in the same manner. After 7 days of continuous use, the MDH/DP biosensor still exhibited 90% of the original sensitivity, while the LOX/HRP biosensor yielded a 91% of the original response after 5 days. Calibration graphs for l-malic and l-lactic were obtained with linear ranges of 5.2 × 10⁻⁷ to 2.0 × 10⁻⁵ and 4.2 × 10⁻⁷ to 2.0 × 10⁻⁵ M, respectively. The calculated detection limits were 5.2 × 10⁻⁷ and 4.2 × 10⁻⁷ M, respectively. The biosensors exhibited a high selectivity with no significant interferences. They were applied to monitor malolactic fermentation (MLF) induced by inoculation of Lactobacillus plantarum CECT 748^T into a synthetic wine. Samples collected during MLF were assayed for l-malic and l-lactic acids, and the results obtained with the biosensors exhibited a very good correlation when plotted against those obtained by using commercial enzymatic kits.