Ion conductivity studies of blends of poly(methyl methacrylate)-g-poly(ethylene glycol) and poly(ethylene glycol) complexed with LiCF3 SO3

Polymer electrolytes which are adhesive, transparent, and stable to atmospheric moisture have been prepared by blending poly(methyl methacrylate)-g-poly(ethylene glycol) with poly(ethylene glycol)/LiCF₃ SO₃ complexes. The maximum ionic conductivities at room temperature were measured to be in the range of 10⁻⁴ to 10⁻⁵ s cm⁻¹. The clarity of the sample was improved as the graft degree increased for all the samples studied. The graft degree of poly(methyl methacrylate)-g-poly(ethylene glycol) was found to be important for the compatibility between the poly(methyl methacrylate) segments in poly(methyl methacrylate)-g-poly(ethylene glycol) and the added poly(ethylene glycol), and consequently, for the ion conductivity of the polymer electrolyte. These properties make them promising candidates for polymer electrolytes in electrochromic devices. © 1996 John Wiley & Sons, Inc.     

Melting and thermodestruction processes in the poly(ethylene)-nanocrystalline nickel system

Composite materials (CM) based on poly(ethylene) (PE) and nanocrystalline nickel (Ni) have been produced. The effect of the content of nanocrystalline Ni and processes of structure formation of its particles on a melting temperature (T _m), interval of melting, true melting heat (ΔH _m), degree of crystallinity (χ) as well as characteristics of CM thermodestruction have been determined by DTA and thermogravimetry techniques. It was found that these characteristics are changed non-linearly when the content of nanocrystalline Ni increases. The most efficient influence of Ni on the above mentioned characteristics was observed for its low content (0.01 volume part of Ni). It was shown that a formation of a branched multifractal cluster of nickel above a percolation threshold favored a decrease in T _m, ΔH _m, χ of filled PE and a majority of thermal characteristics of CM thermodestruction as well. This revised version was published online in August 2006 with corrections to the Cover Date.     

High-Yield Synthesis of Gold Microplates Using Amphiphilic Block Copolymers: Are Lyotropic Liquid Crystals Required?

Summary : High-yield synthesis of gold microplates is achieved through autoreduction of hydrogen tetrachloroaureate (III) hydrate (HAuCl₄ · 3H₂O) in aqueous solutions of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer (Pluronic L64, EO₁₃PO₃₀EO₁₃) at ambient conditions, in the absence of added energy, reductant, or other surfactants. The formation by the amphiphilic block copolymer of lyotropic liquid crystals (e.g., ordered cylindrical/hexagonal or lamellar phases) is not required for templating the formation of such microplates.     

Poly(ethylene-oxide)-para-disubstituted benzene intercalates. Molecular conformation of the polymer molecule from far infrared spectra

The far infrared spectra of various poly(ethylene oxide)-para-disubstituted benzene intercalates are reported. From a detailed discussion, it is strongly suggested that the formula of these intercalates is either [(p-C₆H₄XY)₃(CH₂CH₂O–)₁₀] _n (for XY=ClCl, BrBr, BrCl, ICl, ClF and CH₃Br) or [(p-C₆H₄XY)₂(CH₂CH₂O)₇] _n (for XY=BrF and IF). In both cases the conformation of the polymer molecule is nearly TTG. In addition the previously described relative disposition of the host and guest molecules is confirmed.     

Fabrication of Gene Carrier via Self-assembly of Poly[(dimethylamino)ethyl Methacrylate] and Poly(aspartic acid)-grafted-Poly(ethylene glycol)

A biocompatible complex has been prepared as gene carrier via electrostatic interaction, which is composed of a polycation, that is, poly[(dimethylamino)ethyl methacrylate] end-capped with cholesterol moiety (Chol-PDMAEMA₃₀), along with a polyanion named poly(aspartic acid)-grafted-poly(ethylene glycol) (PASP-g-PEG). The complexes have less cytotoxicity compared to the case of alone Chol-PDMAEMA₃₀ or branched polyethylenimine (PEI) system.

In the present study, biocompatible complexes have been prepared as gene carrier via electrostatic interaction, which is composed of a polycation, that is, poly[(dimethylamino)ethyl methacrylate] end-capped with cholesterol moiety (Chol-PDMAEMA₃₀), along with a polyanion named poly(aspartic acid)-grafted-poly(ethylene glycol) (PASP-g-PEG). We first synthesized polysuccinimide (PSI) via condensation polymerization of aspartic acid, and then used PEG-NH₂ to react with the partial pentacyclic rings of PSI to yield a kind of graft copolymer polysuccinimide-grafted-poly(ethylene glycol) (PSI-g-PEG). After hydrolysis of the residual succinimide units, a new biodegradable and biocompatible graft copolymer PASP-g-PEG was prepared successfully. Chol-PDMAEMA₃₀ was synthesized via oxyanion-initiated polymerization, as reported in our previous literature. We investigated the interactions between every pair among calf thymus DNA, Chol-PDMAEMA₃₀, and PASP-g-PEG by agarose gel retardation assay. The results indicate that the prepared complexes could completely bind DNA and may become more stable during systemic circulation. The complexes have less cytotoxicity compared to the case of alone Chol-PDMAEMA₃₀ or branched polyethylenimine (PEI) system. Furthermore, the physicochemical properties of the complexes were also investigated by zeta potential, transmission electron microscopy (TEM) and dynamic light scattering (DLS) measurements. These biodegradable and biocompatible polymeric carriers have potential applications in gene delivery.     

Hydrophilic segmented block copolymers based on poly(ethylene oxide) and monodisperse amide segments

Segmented block copolymers based on poly(ethylene oxide) (PEO) flexible segments and monodisperse crystallizable bisester tetra‐amide segments were made via a polycondensation reaction. The molecular weight of the PEO segments varied from 600 to 4600 g/mol and a bisester tetra‐amide segment (T6T6T) based on dimethyl terephthalate (T) and hexamethylenediamine (6) was used. The resulting copolymers were melt‐processable and transparent. The crystallinity of the copolymers was investigated by differential scanning calorimetry (DSC) and Fourier Transform infrared (FTIR). The thermal properties were studied by DSC, temperature modulated synchrotron small angle X‐ray scattering (SAXS), and dynamic mechanical analysis (DMA). The elastic properties were evaluated by compression set (CS) test. The crystallinity of the T6T6T segments in the copolymers was high (>84%) and the crystallization fast due to the use of monodisperse tetra‐amide segments. DMA experiments showed that the materials had a low T_g, a broad and almost temperature independent rubbery plateau and a sharp flow temperature. With increasing PEO length both the PEO melting temperature and the PEO crystallinity increased. When the PEO segment length was longer than 2000 g/mol the PEO melting temperature was above room temperature and this resulted in a higher modulus and in higher compression set values at room temperature. The properties of PEO‐T6T6T copolymers were compared with similar poly(propylene oxide) and poly(tetramethylene oxide) copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4522–4535, 2007     

Synthesis and thermal analysis of branched and “kinked” poly(ethylene terephthalate)

Poly(ethylene terephthalate) (PET) was synthesized by self-condensation of bis-(2-hydroxyethyl) terephthalate (BHET). Copolymerization of BHET with ethyl, bis-3,5-(2-hydroxyethoxy) benzoate (EBHEB) and ethyl, 3-(2-hydroxyethoxy) benzoate (E3HEB) yielded copolymers that contain varying amounts of branching and kinks, respectively. Copolymers of BHET with ethyl, 4-(2-hydroxyethoxy) benzoate (E4HEB), in which only the backbone symmetry is broken but without disruption of the linearity, were also prepared for comparison. The composition of the copolymers were established from their ¹H-NMR spectra. The intrinsic viscosity of all the copolymers indicated that they were of reasonably high molecular weights. The thermal analysis of the copolymers using DSC showed that both the melting temperatures (T_m) and the percent crystallinity (as seen from the enthalpies of melting) (ΔH_m) decreased with increasing comonomer (defect concentration) content, although their glass transition temperatures (T_g) were less affected. This effect was found to be most pronounced in the case of branching, while the effects of kinks and linear disruptions, on both T_m and ΔH_m, were found to be similar. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 309–317, 1998     

Crosslinkable interpolymer complexes of novolac resin and poly(ethylene oxide)

Crosslinkable interpolymer complexes of novolac resin and poly(ethylene oxide) (PEO) were prepared by mutual mixing ethanol solutions of novolac and PEO. Fourier transform infrared (FTIR) studies revealed that the driving force for the formation of novolac/PEO complex is hydrogen bonding interaction between the hydroxyl groups of novolac and the ether oxygens of PEO. The morphology and thermal properties of the complexes before and after curing were investigated by optical microscopy and differential scanning calorimetry (DSC). It was found that the uncured novolac/PEO complexes had a single composition-dependent glass transition temperature (T_g). The curing with 15 wt % hexamine (HMTA) (relative to novolac content) resulted in disappearing of T_g behaviour for both the neat novolac and the novolac-rich complexes, owing to less mobility of the novolac chain segments. The melting temperature (T_m) and crystallization rate of the HMTA-cured novolac/PEO complexes decreased with increasing novolac content, and no T_m was observed for the cured complexes with PEO content less than 50%. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36 : 401–411, 1998     

Novel synthesis of biodegradable amphiphilic linear and star block copolymers based on poly(ε‐caprolactone) and poly(ethylene glycol)

Biodegradable, amphiphilic, diblock poly(ε‐caprolactone)‐block‐poly(ethylene glycol) (PCL‐b‐PEG), triblock poly(ε‐caprolactone)‐block‐poly(ethylene glycol)‐block‐poly(ε‐caprolactone) (PCL‐b‐PEG‐b‐PCL), and star shaped copolymers were synthesized by ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) methyl ether or poly(ethylene glycol) or star poly(ethylene glycol) and potassium hexamethyldisilazide as a catalyst. Polymerizations were carried out in toluene at room temperature to yield monomodal polymers of controlled molecular weight. The chemical structure of the copolymers was investigated by ¹H and ¹³C NMR. The formation of block copolymers was confirmed by ¹³C NMR and DSC investigations. The effects of copolymer composition and molecular structure on the physical properties were investigated by GPC and DSC. For the same PCL chain length, the materials obtained in the case of linear copolymers are viscous whereas in the case of star copolymer solid materials are obtained with low T_g and T_m temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3975–3985, 2007     

Thermo‐mechanical Properties of PEO‐PU/PAN Semi‐Interpenetrating Polymer Networks and their LiClO4 Salt‐Complexes

This paper is an investigation on the thermo‐mechanical properties of a new class of materials, which holds promise for its potential use as solid polymer electrolytes, i.e., SPE material. A series of poly(ethylene oxide)‐polyurethane/poly(acrylonitrile) (PEO‐PU/PAN) semi‐IPNs, along with their LiClO₄ salt complexes, were characterized for their thermal, mechanical and dimensional stability using DSC, TG‐DTA, UTM and DMTA. The glass transition temperature (T_g) of both the undoped and doped semi‐IPNs, obtained by DSC, remained well below room temperature (～?50°C to ?35°C), satisfying one of the essential requirements to serve as a SPE host matrix. The crystallization process in the PEO segments of the PEO‐PU/PAN semi‐IPNs was prevented at higher salt concentrations, which is attributed to the Li⁺ ion mediated pseudo‐crosslinks. Good thermal stability of the semi‐IPNs was evident from the degradation onset temperature (T₀～240°C) with a three‐stage degradation process, which is independent of the PAN content as observed from differential thermogravimetric studies. The incorporation of PAN in the PEO‐PU networks results in improved mechanical properties, such as tensile strength and modulus while retaining the flexibility of the semi‐IPNs. The peak temperatures and storage modulus obtained from DMTA correlates well with the observations of DSC and tensile measurements.     

Synthesis and characterization of hydrophilic thermotropic block copolyetheresters

The block copolyetheresters with a hard segment of poly (hexamethylene p,p′-bibenzoate) and a soft segment of poly (ethylene oxide) were prepared by melt polycondensation of dimethyl-p,p′-bibenzoate, 1,6-hexanediol, and polyethylene glycol (PEG) with molecular weights of 400, 1000, 2000, or 4000. These block copolyetheresters were characterized by intrinsic viscosity, GPC, FT-IR, ¹H-NMR, and water absorption. The thermotropic liquid crystalline properties were investigated by DSC, polarized microscope, and x-ray diffraction. The block copolyetheresters exhibit smectic liquid crystallinity due to the polyester segment. The transitions are dependent on the molar content and the molecular weight of PEG used. The block copolyetheresters show high water absorption due to the hydrophilic nature of the poly (ethylene oxide) segment. The water absorption increases with increasing PEG content. As the molecular weight of PEG increases, the water absorption increases significantly. The results indicate that the water absorption of the poly (ethylene oxide) segment in the block copolymers is affected by the presence of polyester segments. © 1995 John Wiley & Sons, Inc.     

Hydrogen bond mediated self-assembly of two diblock copolymers

Two chemically dissimilar diblock copolymers, polybutadiene-b-poly(acrylic acid), PBd-b-PAA (M_w = 5.8–4 kg mol⁻¹) and poly(styrene)-b-poly(ethylene oxide), PS-b-PEO (M_w = 9–5 kg mol⁻¹) were blended in an effort to achieve morphologies typical of triblock copolymers. Blend compatibility was achieved by the hydrogen bond driven association of the PAA block of one diblock with the PEO block of the other. Small angle X-ray scattering was used to determine the morphologies of the compositions, which were further investigated using transmission electron microscopy and selective staining techniques. The crystallinity of the PEO block was determined by differential scanning calorimetry. The hydrogen bond interactions between PEO and PAA yielded a complex triblock lamellar morphology of the form PS-b-(PEO/PAA)-b-PBd-b-(PEO/PAA). This morphology was stable when crystallization of PEO was suppressed by sufficient interaction with PAA.     

Micellization to gelation of a triblock copolymer in water: Thermoreversibility and scaling

Aqueous solutions of a poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) triblock copolymer, Pluronic F108 (PEO₁₃₃PPO₅₀PEO₁₃₃), ranging from 1 to 35 wt %, were studied with differential scanning microcalorimetry and rheology. The thermoreversible micellization and gelation were examined through a heating process and a subsequent cooling process at a fixed rate of 1 °C/min. The critical micellization temperature (CMT), determined by the onset temperature of the endothermic peak in the heating process, was a decreasing function of the F108 concentration. A small secondary endothermic peak appeared only when the polymer concentration was 22.5 wt % or higher, indicating that there was a sol–gel transition but that the gelation was a nearly athermic process. Upon heating, an abrupt increase was observed in both the dynamic storage modulus (G′) and dynamic loss modulus (G″) within a narrow temperature range. T_G′, the temperature for the transition in G′, was a linear decreasing function of the polymer concentration and different from CMT. T_G′ tended to approach CMT with an increasing F108 concentration. Beyond this transition, G′ reached a plateau, and the plateau increased in height and broadened with the polymer concentration. The value of G′ at 70 °C (G′₇₀) could be approximately scaled with concentration c by G′₇₀ ∝ c^7.3. In addition, the definition for a gel to obey G′ > G″ was valid only when c was greater than 22.5 wt %, and this was in agreement with the secondary endothermic peak found with differential scanning calorimetry. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2014–2025, 2004     

Crystallization and melting behaviour of poly(m-xylene adipamide)

The melting and crystallisation behaviour of poly(m-xylene adipamide) (MXD6) are investigated by using the conventional DSC, X-ray diffraction and polarised light microscopy. Triple, double or single melting endotherms are obtained in subsequent heating scan for the samples after isothermal crystallisation from the melt state at different temperatures. The lowest melting peak can be ascribed to the melting of secondary crystals. The melting of primary crystals causes the medium melting peak and the highest melting peak is attributed to the melting of recrystallised species formed during heating. Following the Hoffman–Weeks theory, the equilibrium melting temperature is equal to 250°C and the equilibrium melting enthalpy ΔH _m ⁰ to 175 J g^–1. Then, using the Lauritzen–Hoffmann theory of secondary crystallisation, the analyse of the spherulitic growth shows that the temperature of transition between the growing regimes II and III is equal to 176°C. Finally the Gibbs-Thomson relationship allows the determination of the distribution function of crystalline lamellae.     

Anchoring of hydrophobically modified poly(sodium acrylate)s into DDP vesicle bilayers: hydrophobic match and mismatch

 Differential scanning microcalorimetric thermograms have been recorded for aqueous solutions containing vesicles formed by sodium di-n-dodecyl phosphate, in the presence of different concentrations of poly(sodium acrylate-co-n-alkyl methacrylate), where n-alkyl= C₉H₁₉, C₁₂H₂₅, C₁₈H₃₇. The mole fraction of hydrophobic moieties in the copolymer is 0.04. The main phase transition temperature (T _m) is hardly affected by the presence of poly(sodium acrylate)s bearing n-dodecyl chains, whereas the anchoring of polymers bearing n-nonyl or n-octadecyl groups reduces the main phase transition temperature significantly from ca. 34 °C to ca. 32 °C. In parallel, the enthalpy of transition per mole of DDP monomer (Δ_m H _int) is lowered upon adding polymer. Again, the polymer containing n-dodecyl moieties hardly affects Δ_m H _int. These patterns are explained by the notion that the extent of the disruptive effect of alkyl chains incorporated into the bilayer depends on the extent of the mismatch between the chain lengths of the intruding alkyl chains and the hydrophobic moieties composing the vesicle bilayer. Added hydrophobically modified polymers increase the cooperativity of the melting process, as shown by the increase of n _DDP. We suggest that the anchoring poly(sodium acrylate-co-n-alkyl methacrylate) relieves the strain in the curved outer monolayer of a pure DDP bilayer by allowing the presence of larger “patches” characterized by low curvature. Received: 12 May 1997 Accepted: 20 October 1997     

A facile synthesis of hydrophilic poly(ε-caprolactone)-based poly(ether-ester-amide)s

Segmented poly(ether-ester-amide)s, (PEEA)s, of controlled hydrophilicity degree, based on poly(ε-caprolactone) (PCL), were synthesized according to a facile two-step procedure using α,ω-dihydroxy oligomeric PCL, 4,7,10-trioxa-1,13-tridecanediamine and macromers prepared from poly(ethylene glycol)s and adipoyl chloride. The PEEAs showed M _n values in the range 5–11.5 kDa. A PCL-type crystallinity was found by WAXS. DSC indicated T_m values (49–51 °C) close to that of PCL macromer. Single glass transitions were observed both by DSC and DMTA techniques and the T_g values (−58–−50 °C by DSC) were slightly higher than that of PCL. The water uptake was in the range 4.8–26.0 wt.-% depending on the length of the poly(ethylene glycol) segment.

Monomers used to prepare the PEEAs.     

POLYMERIZATION OF ETHYLENE METHYL PHOSPHATE IN THE PRESENCE OF SODIUM POLY(ETHYLENE GLYCOL)ATE*

Poly(ethylene methyl phosphate)-poly(ethylene glycol)-poly(ethylene methyl phosphate) triblockcopolymers carrying hydroxyl group at both chain ends were synthesized with sodium poly(ethyleneglycol)ate as initiator. The effects of the factors such as solvent, amount of the initiator and reaction timewere investigated. The copolymers were characterized by IR, ~1H-NMR, ~1H{~(31)P}-NMR, ~(13)C-NMR, ~(31)P{~1H}-NMR, and DSC. High molecular weight of the copolymer and high yield of the polymerization were achievedwithin 3 min at 25℃. The polymerization process was studied by ~(31)P{~1H}-NMR and transesterification wasfound during longer polymerization time.     

Poly(vinyl alcohol)-Graft-Poly(ethylene glycol)-Supported Hydroxyproline Catalysis of Stereoselective Aldol Reactions

Summary: The good swelling and high loading of poly(vinyl alcohol)-graft-poly(ethylene glycol) (PVA-g-PEG) resins proved to be effective for performing supported proline-catalyzed aldol reactions stereoselectively in a wide range of polar non-protic, protic and non-polar solvents as well as in neat substrate. The catalysts could be recovered by filtration and recycled, without significant loss of activity. The use of poly(vinyl alcohol)-graft-poly(ethylene glycol) matrix improved the solubility of the proline-derived catalysts and expanded the scope of permissible solvents for performing selective aldol chemistry.     

Ring-Opening Polymerization of the Cyclic Ester Amide Derived from Adipic Anhydride and 1-Amino-6-hexanol in Melt and in Solution

The ring-opening polymerization (ROP) of the cyclic ester amide (cEA) 5 (systematic name, 1-oxa-8-aza-cyclotetradecane-9,14-dione) - prepared from adipic anhydride and 1-amino-6-hexanol - in the melt at 165 °C and in solution at 100 °C and 120 °C with Bu₂Sn(OMe)₂ or Ti(OBu)₄ as initiator yields the alternating poly(ester amide) (PEA) 4 (systematic name, poly(5-(6-oxyhexylcarbamoyl)-pentanoate) with regular microstructure. Kinetic studies for different monomer-to-initiator ratios, different reaction media, initiators and temperatures reveal that the ROP is a first-order reaction with respect to the monomer. Under suitable polymerization conditions termination and transfer reactions are suppressed. The elementary chain growth reaction proceeds by a coordination insertion mechanism in analogy to the polymerization of lactones. By using monohydroxy- and bishydroxy-functional telechelic poly(ethylene oxide) and Sn(octoate)₂ as the initiating system poly(ethylene oxide)-block-poly(ester amide)s and poly(ester amide)-block-poly(ethylene oxide)-block-poly(ester amide)s are obtained. The poly(ester amide) 4 is a semicrystalline material with a melting point of 140 °C, the block copolymers are phase separated systems showing two melting points characteristic for the respective homopolymers.     

High‐pressure DTA of poly(butylene terephthalate), poly(hexamethylene terephthalate), and poly(ethylene terephthalate)

Pressure effect on the melting behavior of poly(butylene terephthalate) (PBT) and poly(hexamethylene terephthalate) (PHT) was studied by high‐pressure DTA (HP‐DTA) up to 320 and 530 MPa, respectively. Cooling rate dependence on the DSC melting curves of the samples cooled from the melt was shown at atmospheric pressure. Stable and metastable samples were prepared by cooling from the melt at low and normal cooling rates, respectively. DTA melting curves for the stable samples showed a single peak, and the peak profile did not change up to high pressure. Phase diagrams for PBT and PHT were newly determined. Fitting curves of melting temperature (T_m) versus pressure expressed by quadratic equation were obtained. Pressure coefficients of T_m at atmospheric pressure, dT_m/dp, of PBT and PHT were 37 and 33 K/100 MPa, respectively. HP‐DTA curves of the metastable PBT showed double melting peaks up to about 70 MPa. In contrast, PHT showed them over the whole pressure region. HP‐DTA of stable poly(ethylene terephthalate) (PET) was also carried out up to 200 MPa, and the phase diagram for PET was determined. dT_m/dp for PET was 49 K/100 MPa. dT_m/dp increased linearly with reciprocal number of ethylene unit. The decrease of dT_m/dp for poly(alkylene terephthalate) with increasing a segmental fraction of an alkyl group in a whole molecule is explained by the increase of entropy of fusion. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 262–272, 2000