Thermal expansion in the Burns-phase of barium titanate stannate

The thermal expansion S_T has been measured in the system BaTi_1−xSn_xO₃, both for the pure compositions x=0 (BT) and x=1 (BS), and for solid solutions 0.025≤x≤0.2 (BTS). For all ceramics examined, a non-linear temperature dependence S_T(T) has been observed at elevated temperatures This is related to thermally generated impurities and, below the Burns-temperature T_d of BT and BTS, to the non-linear strain contribution of polar nanoregions. With increasing Sn-content x, a steep increase of the Burns-temperature is found in BTS for compositions x≥0.025.     

Characterization of LaMnAl11O19 by FT-IR spectroscopy of adsorbed NO and NO/O2

The nature of the NO_x species produced during the adsorption of NO at room temperature and during its coadsorption with oxygen on LaMnAl₁₁O₁₉ sample with magnetoplumbite structure obtained by a sol-gel process has been investigated by means of in situ FT-IR spectroscopy. The adsorption of NO leads to formation of anionic nitrosyls and/or cis-hyponitrite ions and reveals the presence of coordinatively unsaturated Mn³⁺ ions. Upon NO/O₂ adsorption at room temperature various nitro-nitrato structures are observed. The nitro-nitrato species produced with the participation of electrophilic oxygen species decompose at 350 °C directly to N₂ and O₂. No NO decomposition is observed in absence of molecular oxygen. The adsorbed nitro-nitrato species are inert towards the interaction with methane and block the active sites (Mn³⁺ ions) for its oxidation. Noticeable oxidation of the methane on the NOx⁻-precovered sample is observed at temperatures higher than 350 °C due to the liberation of the active sites as a result of decomposition of the surface nitro-nitrato species. Mechanism explaining the promoting effect of the molecular oxygen in the NO decomposition is proposed.     

Liénard-type chemical oscillator

Using first-principles calculation, we have studied the properties of a series of M _x Co_1?x /Co(0001) (M = Pd, Pt) bimetallic surface alloys with atom M ratios from 0.25 to 1.0, then the effect of alloyed M metal on the properties of S adsorbed on these surfaces are discussed. Our calculations show that the alloying of metal Pd, Pt on Co(0001) weakens the S-M (M = Pd, Pt, Co) bond strength compared to monometallic surfaces and the site preference of sulfur atom is dependent on the alloyed metal M and its surface concentration. Moreover, bimetallic surface electronic structure modifications with and without sulfur are analyzed in comparison with clean Co(0001), and the correlation between the sulfur adsorption energy and the bimetallic surface d-band center is presented.     

Al versus Si competition in FeSiAl alloys

In FeSiAl alloys, when Si substitutes for Al, important changes take place in the magnetism as well as in the structural properties. Alloys in the two composition series Fe₇₅Al_25−xSi_x (x=0, 7.5, 12.5, 17.5, 25) and Fe₇₀Al_30−xSi_x (x=0, 9, 15, 21, 30) were prepared by induction melting; afterwards they were crushed and then annealed in order to recover the DO₃ stable phase. The deformed FeAl samples show larger lattice parameters than the ordered ones; however, this difference (Δa) decreases when Si substitutes for Al until it becomes zero (i.e. until the ordered samples and the deformed ones have the same lattice parameters). This trend is the same for both sample series and does not depend on the Fe content of the alloy. However, the magnetization has a different behaviour depending on the Fe content. For deformed Fe₇₅Al_25−xSi_x alloys the saturation magnetization decreases with increasing Si content while for Fe₇₀Al_30−xSi_x deformed alloys the saturation magnetization has a plateau in which the saturation magnetization values do not vary.     

Density functional theory study of Ir atom deposited on γ-Al2O3 (001) surface

Iridium adsorption on γ-Al₂O₃ (001) surface has been studied using the ab initio calculation method and the electronic structures of the bare and the Ir adsorbed γ-Al₂O₃ (001) surfaces have been analyzed. By modeling different adsorption sites, one can conclude that the energetically most favorable sites for the Ir are the top sites of the O atoms at the γ-Al₂O₃ (001) surface terminated with octahedral Al. Charge redistribution around the Ir atom adsorbed on the surface improves the activity of the Ir atom as a catalyst.     

Vehicular traffic through a self-similar sequence of traffic lights

We study the dynamical behavior of vehicular traffic through a sequence of traffic lights positioned self-similarly on a highway, where all traffic lights turn on and off simultaneously with cycle time T_s. The signals are positioned self-similarly by Cantor set. The nonlinear-map model of vehicular traffic controlled by self-similar signals is presented. The vehicle exhibits the complex behavior with varying cycle time. The tour time is much lower such that signals are positioned periodically with the same interval. The arrival time T(x) at position x scales as (T(x)-x)∝x^d_f, where d_f is the fractal dimension of Cantor set. The landscape in the plot of T(x)−x against cycle time T_s shows a self-affine fractal with roughness exponent α=1−d_f.     

First-principles study of half-metallic ferromagnetism in Zn1−xCrxSe

The first-principles full-potential linearized augmented plane-wave method within the generalized gradient approximation for the exchange-correlation functional is used to investigate the structural, electronic and magnetic properties of Zn_1−xCr_xSe (x=0.25, 0.5, 0.75 and 1.0). We find that Zn_1−xCr_xSe exhibits a half-metallic characteristic, and the ferromagnetic state is more favourable in energy than the antiferromagnetic state. The calculated total magnetic moment of Zn_1−xCr_xSe per Cr atom is 4.00 μ_B, which mainly arises from the Cr atom with a little contribution from the Se and Zn atoms. Furthermore, the robustness of half-metallicity with respect to the variation of lattice constants of Zn_1−xCr_xSe is discussed.     

Effect of carbon content on structure and magnetic properties for (Fe,Ni)1−xCx by mechanical alloying

FCC (Fe₅₅Ni₄₅)_1−xC_x   supersaturated solid solution was prepared in a wide concentration range (0?x?0.9)$(0?x?0.9)$ by mechanical alloying of nanocrystalline Fe₅₅Ni₄₅ with graphite. The lattice constant of Fe₅₅Ni₄₅ increases linearly with increasing carbon content up to x=0.25$x=0.25$. At the same time, it is found that the magnetic moment per metal atom (Fe, Ni) decreases linearly with increasing carbon content for 0?x?0.25$0?x?0.25$ with a slope of 1.2 μ_B/at. For high carbon content, x?0.5$x?0.5$, it is observed that the decrease of lattice constant and increase of moment per metal atom (Fe, Ni) with increasing C content, indicates that the dissolution of carbon is hindered by the high-volume fraction of graphite in the initial powder mixture. The complete amorphization of x=0.5$x=0.5$ does not occur after the extended ball milling. The alloying effect of carbon on the magnetization is compared with other metalloid B, P, and Si in Fe- and Ni-based binary system.     

Magnetic and transport property studies of nanocrystalline ZnxFe3−xO4

The magnetic and transport properties of nanocrystalline Zn_xFe_3−xO₄ with x=0.0, 0.2, 0.4, 0.5, 0.6, 0.8 and 1.0, respectively, fabricated by the sol-gel method have been investigated. Large magnetoresistance (MR) was observed and found to be originated both from the tunneling of the spin-polarized electrons across the adjacent ferromagnetic grains and the scattering by the canted spins at the grain surface near the grain boundaries. It has been revealed that the MR for the Zn_xFe_3−xO₄ samples (x=0, 0.5 and 1.0) increases with the temperature decreasing from room temperature until a maximum is reached at around 55 K. Then a sharp drop occurs with the further decrease in temperature, regarded as a spin (cluster) glass transition. For the samples studied, a biggest low field (0.5 T) MR value of about 20% for x=0 at 55 K has been obtained. The mechanism of the MR behavior of the materials was discussed.     

Magnetic properties and magneto electric effect in ferroelectric rich Ni0.5Zn0.5Fe2O4+BPZT ME composites

Magneto electric composites with composition (x) Ni_0.5Zn_0.5Fe₂O₄+(1-x) Ba_0.8Pb_0.2Zr_0.8Ti_0.2O₃ (BPZT—barium lead zirconate titanate) in which x varies as 0.0, 0.15, 0.30, 0.45 and 1.0 mol% were prepared by standard double sintering ceramic method. The presence of constituent phases such as ferrite and ferroelectric was confirmed by X-ray diffraction. The structural analyses were carried out by using X-ray diffraction pattern. Scanning electron micrographs (SEM) were taken to understand the microstructure of the samples. The calculated values of the porosity of the samples lie between 4.5% and 16.2%. The hysteresis measurements were made to determine saturation magnetization (M_s), magnetic moment (μ_B) and coercivity (H_c). From the AC susceptibility measurements the contribution of both the single domain (SD) particles of the ferrite phase and mixed domain (SD+MD) particles of the composites in ME output were explained. The static magneto electric voltage coefficients (dE/dH)_H were measured as a function of intensity of magnetic field and the maximum ME coefficient were observed for the composites with 30% of ferrite+70% of ferroelectric phase.     

Nitrogen-rich carbon nitride materials shock-synthesized from carbon tetrahalide and sodium dicyanoamide

Shock reactions between CX₄ (X=Br or I) and NaN(CN)₂ were investigated to prepare carbon nitrides. The post shock samples were characterized by the powder X-ray diffraction (XRD) technique. The XRD spectrum of the product showed a peak in the range of 0.324-0.336 nm in d-value corresponding to the (002) basal plane diffraction in graphitic structure. Elemental analysis (C, H, N, O) of the product showed that the atomic ratio of nitrogen to carbon (N/C) ranged from 0.38 to 1.3. Analysis of data revealed that the d-value increased and the nitrogen content decreased with the increase of the impact velocity.     

Electron-doped Sm1−xSrxMnO3 perovskite manganites: Crystal and magnetic structures and physical properties

We present the results of a study of electron-doped Sm_1−xSr_xMnO₃ (x>0.5) perovskite manganites by combining high-resolution neutron powder diffraction with measurements of resistivity, magnetization and magnetic susceptibility. Although investigated Sm_0.45Sr_0.55MnO₃ and Sm_0.37Sr_0.63MnO₃ compounds belonging to the same phase diagram area differ significantly in the strontium content, they are homogeneous antiferromagnetic (AF) insulators and do not exhibit CMR. They have different crystallographic symmetries (orthorhombic Pbnm and tetragonal I4/mcm, respectively) in the entire temperature range under study (1.5-288 K), differ in the type of spin ordering at low temperatures (AF-A and AF-C), are characterized by different orbital polarizations (d_x²_−y² and d_3z²_−r²), and possess two- and one-dimensional magnetic properties, respectively. The lack of magnetoresistance for these compositions is explained by the lack of coexisting magnetic phases involving double exchange ferromagnetism, in contrast to what is observed for the magnetoresistive Sm_1−xSr_xMnO₃ compounds, that is with x?0.52.     

Magnetic ordering above room temperature in the sigma-phase of Fe66V34

Magnetic properties of four sigma-phase Fe_100−xV_x samples with 34.4?x?55.1 were investigated by Mössbauer spectroscopy and magnetic measurements in the temperature interval 4.2-300 K. Four magnetic quantities, viz. hyperfine field, Curie temperature, magnetic moment and susceptibility, were determined. The sample containing 34.4 at% V was revealed to exhibit the largest values found up to now for the sigma-phase for average hyperfine field, 〈B〉=12.1 T, average magnetic moment per Fe atom, 〈μ〉=0.89 μ_B, and Curie temperature, T_C=315.3 K. The quantities were shown to be strongly correlated with each other. In particular, T_C is linearly correlated with 〈μ〉 with a slope of 406.5 K/μ_B, as well as 〈B〉 is so correlated with 〈μ〉, yielding 14.3 T/μ_B for the hyperfine coupling constant.     

Adsorption of a semiflexible wormlike chain

Adsorption of ideal polymers with stiff backbone onto a flat surface is considered theoretically. Both scaling approach and quantitative theory are developed. We predict a self-similar monomer concentration profile c(x) ∼ x ^-4/3 near the surface (when the distance to the surface x is much smaller than the chain persistence length l /2). The typical conformation of a weakly adsorbed chain can be viewed as a sequence of alternating flat (2-dimensional) trains of wormlike short loops (flat blobs) and coil-like (3-dimensional) loops forming a triple-layer structure: contact layer (x < Δ) of adsorbed fragments virtually laid on the surface, proximal layer (Δ < x < l) of flat blobs, and more dilute distal corona layer (x > l). Here Δ defines the range of monomer/surface attraction, Δ ≪ l. The adsorption transition is continuous. However, its relative width is small (T ^* is the adsorption temperature, ΔT is the relevant temperature interval): ∼ , i.e. a discontinuous transition in the limit Δ/l↦ 0. Received 10 October 2002 and Received in final form 22 November 2002 RID="a" ID="a"Permanent address: Physics Department, Moscow State University, Moscow 119992, Russia. e-mail: semenov@polly.phys.msu.ru     

First-principles study of single-walled armchair Cx(BN)y nanotubes

The structural and electronic properties of the armchair C_x(BN)_y nanotubes are studied using the density functional theory with a generalized gradient approximation. The results show that the properties of the C_x(BN)_y nanotubes are intermediate between those of carbon nanotubes and BN nanotubes, and also adjustable by their radius, ratio of carbon component, and configurations.     

Density functional theory study into the adsorption of CO2, H and CHx (x = 0-3) as well as C2H4 on α-Mo2C(0 0 0 1)

The structures and energetics of the chemisorbed CO₂, CH_x species and H as well as C₂H₄ on the α-Mo₂C(0 0 0 1) surface have been computed at the GGA-RPBE level of density functional theory. It is found that CO₂ adsorbs dissociately into CO and O, in agreement with the experimental finding. The adsorbed O, CH_x and H species prefer the site of three surface molybdenum atoms over a second layer carbon atom (V_C site). On the basis of the calculated adsorption energies of CH_x and H, the sequential dehydrogenation of CH₄ and the C/C coupling reaction of CH_x have been discussed.     

Study of the magnetization and transport properties of the La(2+x)/3Sr(1−x)/3Mn1−xCrxO3 (0≤x≤0.2) system

The samples with the Mn³⁺/Mn⁴⁺ ratio fixed at 2:1 La_(2+x)/3Sr_(1−x)/3Mn_1−xCr_xO₃ (0≤x≤0.20) have been prepared. The magnetic, electrical transport, and magnetoresistance properties have been investigated. Remarkable transport and colossal magnetoresistance (CMR) effect, as well as cluster glass (CG) behaviors have been clearly observed in the samples studied. It was found that the Curie temperature T_c and insulator−metal transition temperature T_p1 are strongly affected by Cr substitution. The experiment observations are discussed by taking into account the variety of tolerance factors t; the effects of A-site radius 〈r_A〉 and the A-site mismatch effect (σ²).     

The role of iron in the formation of the magnetic structure and related properties of La0.8Sr0.2Co1−xFexO3 (x=0.15, 0.2, 0.3)

La_0.8Sr_0.2Co_1−xFe_xO₃ (x=0.15, 0.2, 0.3) samples were studied by means of AC magnetic susceptibility, magnetization, magnetoresistance and ⁵⁷Fe Mössbauer spectrometry. Iron was found to take on a high spin 3d^5−α electronic state in each of the samples, where α refers to a partly delocalized 3d electron. The compounds were found to exhibit a spin-cluster glass transition with a common transition temperature of ∼53 K. The spin-cluster glass transition is visualized in the ⁵⁷Fe Mössbauer spectra as the slowing down of magnetic relaxation below ∼70 K, thereby showing that iron takes part in the formation of the glassy magnetic phase. The paramagnetic-like phase found at higher temperatures is identified below T_c≈195 K as being composed of weakly interacting, magnetically ordered nanosized clusters of magnetic ions in part with a magnetic moment oriented opposite to the net magnetic moment of the cluster. For each of the samples a considerable low-temperature negative magnetoresistance was found, whose magnitude in the studied range decreases with increasing iron concentration. The observed results obtained on the present compounds are qualitatively explained assuming that the absolute strengths of magnetic exchange interactions are subject to the relation ∣J_Co–Co∣<∣J_Fe–Co∣<∣J_Fe–Fe∣.     

Jahn-Teller distortion and magnetoresistance in electron doped Sr1-xCexMnO3 (x = 0.1, 0.2, 0.3 and 0.4)

Neutron and electron diffraction, electrical transport and magnetic measurements have been carried out on a newly synthesized electron doped Sr_1-xCe _x MnO₃ (x = 0.1, 0.2, 0.3 and 0.4) system. For x=0.1, while cooling, it undergoes a first-order metal-insulator transition at 315 K which is associated with a structural transition from cubic (Pm3m) to tetragonal (I4/mcm) due to Jahn-Teller ordering () which stabilizes a chain like (C-type) antiferromagnetic ground state with . The antiferromagnetic insulator state is insensitive to an applied magnetic field of 7 T. With increase of x, while the nuclear structure at room temperature for x=0.2 and 0.3 remains tetragonal, for x=0.4 it becomes orthorhombic (Imma) where the doping electrons seem to occupy mainly the d _x2-y2 symmetry. Further, the JT distortion and the antiferromagnetic interactions decrease with doping and a small negative magnetoresistance appears for . Magnetic measurements show that the dilution of antiferromagnetic interaction results into a spin glass like behaviour at low temperature for the samples with x=0.3 and 0.4. This behaviour is in contrast with the CMR properties of calcium based electron doped systems and hole doped manganites. The stability of C-type antiferromagnetic ordering in the electron doped system with large A-site cationic size may be responsible for the absence of double exchange ferromagnetism and CMR effect. Received 10 September 1999     

Structure, magnetic, and transport properties of the Co-doped manganites La0.9Te0.1Mn1−xCoxO3 (0≤x≤0.25)

The effect of Co doping at Mn-site on the structural, magnetic and electrical transport properties in electron-doped manganties La_0.9Te_0.1Mn_1−xCoxO₃ (0≤x≤0.25) has been investigated. The room temperature structural transition from rhombohedra to orthorhombic (Pbnm) symmetry is found in these samples with x≥0.20 by the Rietveld refinement of X-ray powder diffraction patterns. All samples undergo the paramagnetic-ferromagnetic (PM-FM) phase transition. The Curie temperature T_C of these samples decreases and the transition becomes broader with increasing Co-doping level. The magnetization magnitude of Co-doping samples increases at low temperatures with increasing Co-doping level for x≤0.15 and decreases with increasing Co-doping content further. The metal-insulator (M-I) transitions observed in the sample with x=0 are completely suppressed with Co doping, and the resistivity displays semiconducting behavior within the measured temperature region for these samples with x>0. All results are discussed according to the changes of the structure parameters and magnetic exchange interaction caused by Co-doping. In addition, the different effects between the Co doping and Cu doping in the Mn site for the electron-doped manganites are also discussed.