Electrochemical properties of thin TiO2 electrode on Li1 + xAlxGe2 − x(PO4)3 solid electrolyte

A fabrication of all-solid-state thin-film rechargeable lithium ion batteries by sol-gel method is expected to achieve both the simplification and cost reduction for fabrication process. TiO₂ thin film electrode was prepared by PVP (polyvinylpyrrolidone) sol-gel method combined with spin-coating on Li_1 + xAl_xGe_2 − x(PO₄)₃ (LAGP) solid electrolyte which has wide electrochemical window. The thin film was composed of anatase TiO₂ that is the most active phase for Li insertion and extraction and contacted well with LAGP substrate. In the cyclic voltammogram, a redox couple was observed at 1.8 V vs. Li/Li⁺ assigned to Li insertion/extraction into/from anatase TiO₂, indicating that the thin film worked as electrode for lithium battery. The charge and discharge test in various charge and discharge rates revealed that the discharge process (delithiation) is thought to be faster than charge process (lithiation). It is attested that the sol-gel process, which derives both simplification and cost reduction for fabrication process, can be applied to thin film battery using LAGP solid electrolyte.     

Crystalline-structure-dependent green and red upconversion emissions of Er-Yb-Li codoped TiO2

Crystalline structures and infrared-to-visible upconversion luminescence spectra have been investigated in 1 mol% Er³⁺, 10 mol% Yb³⁺ and 0-20 mol% Li⁺ codoped TiO₂ [1Er10Yb(0-20)Li:TiO₂] nanocrystals. The crystalline structures of 1Er10Yb(0-20)Li:TiO₂ were divided into three parts by the addition of Yb³⁺ and Li⁺. Both green and red upconversion emissions were observed from the ²H_11/2/⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 transitions of Er³⁺ in Er³⁺-Yb³⁺-Li⁺ codoped TiO₂, respectively. The green and red upconversion emissions of 1Er:TiO₂ were enhanced significantly by Yb³⁺ and Li⁺ codoping, in which the intensities of green and red emissions and the intensity ratio of green to red emissions (I_green/I_red) were highly dependent on the crystalline structures. The significant enhanced upconversion emissions resulted from the energy migration between Er³⁺ and Yb³⁺ as well as the distortion of crystal field symmetry of Er³⁺ caused by the dissolving of Li⁺ at lower Li⁺ codoping concentration and the phase transformation at higher Li⁺ concentration. It is concluded that codoping with ions of smaller ionic radius like Li⁺ can efficiently improve the upconversion emissions of Er³⁺ or other rare-earth ions doped luminsecence materials.     

Role of Cl ions in photooxidation of propylene on TiO2 surface

The effect of Cl⁻ ions on photooxidation of propylene on TiO₂ semiconductor was investigated. Cl⁻/TiO₂ catalysts were prepared by annealing Degussa P25 TiO₂ in the gas flow of N₂ and Cl₂ under 100-400 °C. The photocatalytic oxidation of propylene was carried out in a continuous flow system, with the chromatograph to analyze the products on line. The experimental results showed that the activity of Cl⁻/TiO₂ catalysts increased as heat-treated temperature decreased. The activity of the sample heat-treated at 100 °C was about two times higher than that of pure TiO₂. Moreover, as to TiO₂, the main product of the propylene photocatalytic oxidation was CO₂, but with Cl⁻/TiO₂ catalysts, not only CO₂ but also trace CO was determined. The adsorbed species on TiO₂ surface before and after reaction were analyzed by X-ray photoelectron spectroscopy (XPS) and thermogravimetric/differential thermal analyses (TG-DTA) coupled to a mass spectrometer (MS). XPS analysis showed that there was Cl⁻ absorbed on the Cl⁻/TiO₂ surface, and the absorption amount of Cl⁻ decreased after the photooxidation reaction of propylene. TG-DTA-MS analysis confirmed chlorine absorbed on the surface of TiO₂ in the form of Cl⁻ ion. These results illuminated that absorbed Cl⁻ on the surface of TiO₂ formed a weak physical absorption on TiO₂ at low temperature, and subsequently participated in the photooxidation of propylene, finally removed from TiO₂ surface.     

Preparation and characterization of iodine-doped mesoporous TiO2 by hydrothermal method

Iodine-doped mesoporous TiO₂ (I/TiO₂) was prepared by hydrothermal method, using tetrabutyl titanate as precursor, potassium iodate as iodine sources. The as-prepared I/TiO₂ catalysts were characterized by UV-vis, XRD, TEM, BET, TG/DTA, XPS and photoluminescence (PL) spectroscopy. Production of OH radicals on the I/TiO₂ surface was detected by the PL technique using terephthalic acid as a probe molecule. The effects of hydrothermal reaction temperature, calcination temperature and iodine doping content on the structure and properties of the catalysts were investigated. The results showed that iodine-doped TiO₂ calcinated at 300 °C have good anatase crystal. The optimal hydrothermal conditions have been determined to be that reaction temperature 120 °C, calcinated temperature 300 °C and added 1.16 mmol iodine dopants. The average particle size of I/TiO₂ synthesized under optimal condition (I-3 sample) is about 3.9 nm. The I-3 photocatalyst contains 100% anatase crystalline phase of TiO₂. BET specific surface area of I-3 sample is184.8 m² g⁻¹ and is 3.67 times that of pure TiO₂ (50.37 m² g⁻¹). Iodine in I/TiO₂ catalyst mainly exists in the form of I₂, and photoactivity of I/TiO₂ catalyst in visible light comes from photosensitize of I₂. I/TiO₂ catalysis shows very high efficiency for the degradation of phenol under visible light.     

Synthesis and characterization of TiO2 thin films coated on metal substrate

Nanostructured titanium dioxide (TiO₂) thin films have been prepared on metal substrates using a facile layer-by-layer dip-coating method. The phase structure and morphologies of preparing samples were characterized by means of X-ray powder diffraction (XRD) and field-emission scanning electron microscopy (FESEM). The results confirm that films are highly crystalline anatase TiO₂ and free from other phases of titanium dioxide. Scanning electron microscopy (SEM) shows that the nanoparticles are sintered together to form a compact structure. The electrical properties of samples were investigated by cutternt-voltage analysis, the result indicates that a rectifying junction between the nanocrystalline TiO₂ film and metal substrate was formed. The photoelectrochemical characteristics recorded under 1.5 AM illumination indicates that the as-fabricated thin film electrode possesses the highest photocurrent density at 450 °C, which is 1.75 mA/cm² at 0 V vs. Ag/AgCl.     

Preparation, characterization and visible-light photocatalytic activity of AgI/AgCl/TiO2

In this paper, a novel composite photocatalyst AgI/AgCl/TiO₂ was prepared by ion exchange method and characterized by XRD, SEM and UV-Vis spectrometry. The as-prepared AgI/AgCl/TiO₂ composites show much higher photocatalytic activity than AgCl/TiO₂ and AgI/TiO₂ under visible-light irradiation (λ > 400 nm) in the process of methyl orange (MO) degradation. When the molar percentage of AgI to initial AgCl is 20% (sample SE-20%), the maximal degradation efficiency of MO has reached 85.8% after irradiation for 120 min. The enhancement of photocatalytic activity of the composite photocatalyst AgI/AgCl/TiO₂ will be attributed to its good absorption in the visible-light region, especially low recombination rate of the electron-hole pairs based on the photoluminescence (PL) spectra investigation of AgI/AgCl/TiO₂ and the matching band structures of AgI, AgCl and TiO₂. The detection of reactive species by radical scavengers displays that O₂⁻ and H₂O₂ are the main reactive species for the degradation of MO under visible-light irradiation. Moreover, PL analysis by using terephthalic acid (TA) as a probe molecule further reveals that OH can be negligible for the degradation of MO.     

Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu,S-codoped TiO2 nanoparticles

A novel copper and sulfur codoped TiO₂ photocatalyst was synthesized by modified sol-gel method using titanium(IV) isopropoxide, CuCl₂·2H₂O and thiourea as precursors. The samples were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), scanning electron microscopy equipped with energy dispersive X-ray micro-analysis (SEM-EDX), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) analysis. The XRD results showed undoped and Cu,S-codoped TiO₂ nanoparticles only include anatase phase. Effect of calcination temperature showed rutile phase appears in 650 and 700 °C for undoped and 0.1% Cu,S-codoped TiO₂, respectively. The SEM analysis revealed the doping of Cu and S does not leave any change in morphology of the catalyst surface. The increase of copper doping enhanced “red-shift” in the UV-vis absorption spectra. The TEM images confirmed the dopants suppressed the growth of TiO₂ grains. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. The results showed photocatalytic activity of the catalysts with 0.05% Cu,0.05% S and 0.1% Cu,0.05% S were higher than that of other catalysts under ultraviolet (UV) and visible irradiation, respectively. Because of synergetic effect of S and Cu, the Cu,S-codoped TiO₂ catalyst has higher activity than undoped and Cu or S doped TiO₂ catalysts.     

Photooxidation of different organic dyes (RB, MO, TB, and BG) using Fe(III)-doped TiO2 nanophotocatalyst prepared by novel chemical method

The nano-structured Fe(III)-doped TiO₂ photocatalysts with anatase phase have been developed for the oxidation of non-biodegradable different organic dyes like methyl orange (MO), rhodamine B (RB), thymol blue (TB) and bromocresol green (BG) using UV-Hg-lamp. The different compositions of Fe_xTi_1−xO₂ (x = 0.005, 0.01, 0.05, and 0.1) nanocatalysts synthesized by chemical method (CM), have been characterized by X-ray diffraction (XRD), UV-vis diffuse reflectance spectra, specific surface area (BET), transmission electronic microscopy (TEM) analysis, XPS, ESR and zeta potential. From XRD analysis, the results indicate that all the compositions of Fe(III) doped in TiO₂ catalysts gives only anatase phase not rutile phase. For complete degradation of all the solutions of the dyes (MO, RB, TB, and BG), the composition with x = 0.005 is more photoactive compared all other compositions of Fe_xTi_1−xO₂, and degussa P25. The decolorization rate of different dyes decreases as Fe(III) concentration in TiO₂ increases. The energy band gap of Fe(III)-doped TiO₂ is found to be 2.38 eV. The oxidation state of iron has been found to be 3+ from XPS and ESR show that Fe³⁺ is in low spin state.     

High-pressure study on the adsorption and oxidation of CO on gold/titania model catalysts

The results of an IR study on the interaction of CO/O₂ gas mixtures with planar Au/TiO₂ model catalysts at elevated pressures and at room temperature are presented. The model catalysts were prepared by deposition of a flat titania film on a Ru(0 0 0 1) substrate and subsequent evaporation of gold on the titania film. In the presence of the gas mixtures, an IR band in the CO stretching region was formed, pointing to linearly adsorbed CO. The position of this band is nearly independent of the Au coverage employed. Compared to pure CO, the IR band is shifted to higher wave numbers when CO/O₂ gas mixtures are used. Although the production of CO₂ was detected in the CO oxidation reaction on the model catalysts, the formation of other IR bands, revealing the build-up of carbonates or other side-products which is usually observed for Au/TiO₂ real powder catalysts, was very weak.     

Highly ordered anodic TiO2 nanotube arrays and their stabilities as photo(electro)catalysts

Highly ordered TiO₂ nanotube arrays with an average diameter of 230 nm, a wall thickness of 30 nm and a length of 1.8 μm were fabricated within a large domain by electrochemically anodizing of a titanium foil in a mixed solution of glycerol and NH₄F aqueous electrolyte. The TiO₂ nanotubes exhibit an anatase structure after annealing at 450 °C in air for 3 h. The direct photolysis (DP), photocatalytic (PC), electrocatalytic (EC) and photoelectrocatalytic (PEC) activities of the TiO₂ nanotube arrays were investigated using methyl orange (MO) as the model pollutant. The degradation of MO in PC process is faster than that in DP process, which confirms the photocatalysis of TiO₂ nanotube arrays. The degradation rate in PEC process is much higher than those in EC and PC processes, which demonstrates the synergetic effect between PC and EC processes. The synergetic factor is 4.1, which suggests that the synergetic effect is strong. Moreover, the stabilities of morphology, structure and photo(electro)catalytic degradation performance of the TiO₂ nanotube arrays were studied in order to evaluate their applicability as photo(electro)catalysts. The photo(electro)catalytic experiments bring neither morphological nor structural modifications to the nanotube arrays. The photo(electro)catalytic degradation rates of the TiO₂ nanotube arrays maintain stable in 10 cycles, which indicates that the TiO₂ nanotube arrays are appropriate to be applied as photo(electro)catalysts.     

Photocatalytic activity of multielement doped TiO2 in the degradation of congo red

TiO₂ although considered a promising photocatalyst for the degradation of aqueous pollutants, it suffers from poor absorption in the visible region and hence requires ultraviolet (UV) light for activation. To make TiO₂ a visible active photocatalyst, multielement (C, N, B, and F) doping has been done. The synthesised CNBF/TiO₂ catalysts were calcined at different temperatures and characterized by XRD, BET surface area, UV DRS, XPS, HRSEM-EDAX, and TEM techniques. These catalysts found to show less band gap values when compared to bare TiO₂. These catalysts were tested for their catalytic activity towards the degradation of a textile dye - congo red (CR) under different reaction conditions. It was found that the photocatalytic activity was dependent on both doping of multielement and the calcination temperature of CNBF/TiO₂. The co-doped catalysts which were calcined at 400 °C and 600 °C (100% intensity in anatase phase) were found to be the best catalysts (100% decolourisation of CR in 21/2 h and 2 h respectively). TOC analysis carried out for the samples at the reaction time of 5 h showed very high percentage (83%) degradation of CR over CNBF/TiO₂ catalysts calcined at 600 °C when compared to the other catalysts calcined at different temperatures. CNBF/TiO₂ (1000 °C) showed very less photocatalytic activity due to the formation of rutile phase.     

A nanogravimmetric investigation of the charging processes on ruthenium oxide thin films and their effect on methanol oxidation

The charging processes and methanol oxidation that occur during the oxidation-reduction cycles in a ruthenium oxide thin film electrode (deposited by the sol-gel method on Pt covered quartz crystals) were investigated by using cyclic voltammetry, chronoamperometry and electrochemical quartz crystal nanobalance techniques. The ruthenium oxide rutile phase structure was determined by X-ray diffraction analysis. The results obtained during the charging of rutile ruthenium oxide films indicate that in the anodic sweep the transition from Ru(II) to Ru(VI) occurs followed by proton de-intercalation. In the cathodic sweep, electron injection occurs followed by proton intercalation, leading to Ru(II). The proton intercalation/de-intercalation processes can be inferred from the mass/charge relationship which gives a slope close to 1 g mol⁻¹ (multiplied by the Faraday constant) corresponding to the molar mass of hydrogen. From the chronoamperometric measurements, charge and mass saturation of the RuO₂ thin films was observed (440 ng cm⁻²) during the charging processes, which is related to the total number of active sites in these films. Using the electrochemical quartz crystal nanobalance technique to study the methanol oxidation reaction at these films was possible to demonstrate that bulk oxidation occurs without the formation of strongly adsorbed intermediates such as CO_ads, demonstrating that Pt electrodes modified by ruthenium oxide particles can be promising catalysts for the methanol oxidation as already shown in the literature.     

A novel approach towards high-performance composite photocatalyst of TiO2 deposited on activated carbon

TiO₂ photocatalysts deposited on activated carbon (TiO₂/AC) were prepared by dip-hydrothermal method at 180 °C using peroxotitanate as a precursor, then calcinated at 300-800 °C. The samples were characterized by X-ray diffraction, scanning electron microscopy, Raman spectroscopy and the nitrogen absorption. Their photocatalytic activity was evaluated by degradation of methyl orange (MO). The results showed that TiO₂ particles of anatase type were well deposited on the activated carbon surface. TiO₂/AC calcinated at 600 °C exhibited the best photocatalytic performance. For the comparison, the same photocatalysis experiment was carried out for two mixtures of commercial TiO₂ (Degussa P25) with AC and synthetic TiO₂ with AC. It was found that the composite catalyst TiO₂/AC was better than the two mixtures. Besides, different from fine powdered TiO₂, the granular TiO₂/AC photocatalysts could be easily separated from the bulk solution and reused; indeed, its photocatalytic ability was hardly decreased after a five-cycle for MO degradation. The kinetics of the MO degradation fitted well the Langmuir-Hinshelwood model.     

Adsorption CO2 on the perfect and oxygen vacancy defect surfaces of anatase TiO2 and its photocatalytic mechanism of conversion to CO

The adsorption energies for physisorption and the most stable chemisorption of CO₂ on the neutral charge of perfect anatase [TiO₂] (0 0 1) are −9.03 and −24.66 kcal/mol on the spin-unpolarized and −12.98 and −26.19 kcal/mol on the spin-polarized surface. The small activation barriers of 1.67 kcal/mol on the spin-unpolarized surface and of 6.66 kcal/mol on the spin-unpolarized surface were obtained. The adsorption mechanism of CO₂ on the oxygen vacancy defect [TiO₂ + V_O] surface of anatase TiO₂ using density functional theory calculations was investigated. The energetically preferred conversion of CO₂ to CO was found either on the spin-unpolarized or spin-polarized surfaces of oxygen vacancy defect surface [TiO₂ + V_O] as photocatalyst.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Investigation on mechanism of photocatalytic activity enhancement of nanometer cerium-doped titania

A series of Ce-TiO₂ are prepared by the sol-gel process with ammonium cerium(IV) nitrate and tetra-n-butyl titanium as raw materials and characterized with XRD, TEM, DRS, and XPS. The aberrance (0.355) of anatase(1 0 1) plane of 0.1% Ce/TiO₂ increases compared to that of TiO₂. Cerium is found to be present as a mixture of Ce^3+/4+ oxidation states, that is, the oxidation state of some cerium in Ce-TiO₂ has changed after calcination. Ce/TiO₂ yields a large red shift compared to TiO₂. Moreover, the reflectance decreases in the visible region after cerium doped on TiO₂, and the lower the reflectance the higher the activity. Cerium appears to enhance the photocatalytic activity of Ce/TiO₂ by suppressing electron-hole recombination with electron trapping at Ce⁴⁺. 0.1% Ce/TiO₂ shows highest activity for the degradation of aqueous suspension of formaldehyde.     

Synthesis of spinel lithium titanate anodes incorporated with rutile titania nanocrystallites by spray drying followed by calcination

Lithium insertion into spinel Li₄Ti₅O₁₂ incorporated with rutile TiO₂ was investigated in order to clarify the redox mechanism responsible for the first plateau at 1.5 V vs. Li/Li⁺. Spherical Li₄Ti₅O₁₂ powders with an average diameter of 2-3 μm can be achieved by spray drying followed by sintering process. The Li/Ti molar ratio in the precursor is selected as the factor for preparing spinel Li₄Ti₅O₁₂ powders with different concentrations of rutile TiO₂. The specific capacity from the first plateau at 1.5 V contributes to the major portion in the overall capacity. The rutile TiO₂ in spinel Li₄Ti₅O₁₂ anodes tends to improve the specific capacity at the first plateau. This can be attributed to two possible reasons: (i) rutile TiO₂ provides an additional number of sites (i.e., oxygen octahedral vacancy in rutile TiO₂) for the Li insertion, and (ii) less amount of residual Li oxides results in high electronic conductivity. The Li₄Ti₅O₁₂ anodes display high rate capability with low irreversible capacity, indicating good reversibility of insertion/de-insertion of Li ions. The results presented in this work show unambiguously that the presence of rutile TiO₂ in spinel Li₄Ti₅O₁₂ has a positive effect on the performance promotion of Li₄Ti₅O₁₂ anodes.     

Dielectric and leakage current properties of Li doped (Ba,Sr)TiO3 thick film interdigital capacitors on the alumina substrates

Li doped (Ba,Sr)TiO₃ thick films were fabricated by employing the screen printing method on the alumina (Al₂O₃) substrates. Interdigital capacitor patterns with seven fingers of 200 μm gap, 250 μm length were designed and screen printed on the alumina substrates. Ba_0.5Sr_0.5TiO₃ materials, paraelectric state at the room temperature, have been chosen for the microwave devices due to high dielectric permittivity and low loss tangent, however, the sintering temperature of (Ba,Sr)TiO₃ is over 1350 °C. In order to lower the sintering temperature, Li (3 wt%) was added to the (Ba,Sr)TiO₃ materials. Li doped (Ba,Sr)TiO₃ thick films screen printed on the alumina (Al₂O₃) substrates were sintered at 900 °C for 1.5 h. The structural feature was analyzed with X-ray diffraction method. Temperature dependent dielectric properties were characterized from 303 to 403 K at 1 MHz. Within the ±100 V of bias voltage, current-voltage characteristics of Li doped (Ba,Sr)TiO₃ films were investigated from 303 to 403 K. Through the current-voltage characteristics, the resistivity of Li doped (Ba,Sr)TiO₃ films were calculated.In this paper, the significant negative temperature coefficient of resistance (NTCR) of Li doped (Ba,Sr)TiO₃ films will be presented through the activation energy fitting. Measured activation energy is approximately 0.366 eV.     

The surface properties and the activities in catalytic wet air oxidation over CeO2-TiO2 catalysts

No-noble metal CeO₂-TiO₂ catalysts prepared by sol-gel method were developed and examined for catalytic wet air oxidation (CWAO) of acetic acid. The structure of the catalysts was measured by BET, SEM, XRD, XPS and DTA-TG. We investigated the effect of the interactions of Ce and Ti on the structure of CeO₂-TiO₂ catalysts. The mechanisms of the relationships between the different content of Ti and the activity of CeO₂-TiO₂ catalysts were discussed. The results showed that the average crystal size of CeO₂ decreased and the surface areas increased; the low valence of Ce³⁺ increase, and the chemisorbed oxygen slightly decreased with the increase of Ti content on the surface of CeO₂-TiO₂ catalysts. The order of the activity in CWAO of acetic acid followed: Ce/Ti 1/1 > Ce/Ti 3/1 > Ce/Ti 1/3 > Ce/Ti 5/1 > CeO₂ > TiO₂ > no catalyst. In CWAO of acetic acid, the optimal atomic ratio of Ce and Ti was 1, and the highest COD removal was over 64% at 230 °C, 5 MPa and 180 min reaction time over Ce/Ti 1/1 catalyst. The excellent activity and stability of CeO₂-TiO₂ catalysts was observed in our study.     

Targeted sonodynamic therapy using protein-modified TiO2 nanoparticles

Our previous study suggested new sonodynamic therapy for cancer cells based on the delivery of titanium dioxide (TiO₂) nanoparticles (NPs) modified with a protein specifically recognizing target cells and subsequent generation of hydroxyl radicals from TiO₂ NPs activated by external ultrasound irradiation (called TiO₂/US treatment). The present study first examined the uptake behavior of TiO₂ NPs modified with pre-S1/S2 (model protein-recognizing hepatocytes) by HepG2 cells for 24 h. It took 6 h for sufficient uptake of the TiO₂ NPs by the cells. Next, the effect of the TiO₂/US treatment on HepG2 cell growth was examined for 96 h after the 1 MHz ultrasound was irradiated (0.1 W/cm², 30 s) to the cells which incorporated the TiO₂ NPs. Apoptosis was observed at 6 h after the TiO₂/US treatment. Although no apparent cell-injury was observed until 24 h after the treatment, the viable cell concentration had deteriorated to 46% of the control at 96 h. Finally, the TiO₂/US treatment was applied to a mouse xenograft model. The pre-S1/S2-immobilized TiO₂ (0.1 mg) was directly injected into tumors, followed by 1 MHz ultrasound irradiation at 1.0 W/cm² for 60 s. As a result of the treatment repeated five times within 13 days, tumor growth could be hampered up to 28 days compared with the control conditions.