Sr2 CeO4电荷迁移发光的光谱结构规律研究

利用高温固相反应法分别合成了不同物相形成机理的Sr2CeO4，Sr2CeO4：Ca^2 和Sr2CeO4：Ba^2 样品，并对其光谱特性进行了研究．结果发现，对于由SrO和CeO2直接反应生成的Sr2CeO4(Ⅰ)，激发主峰位于256nm左右；而对于SrCeO4和SrO反应生成的Sr2CeO4(Ⅱ)，激发主峰位于279nm左右．在Sr2CeO4(Ⅰ)中掺入Ca^2 ，其激发光谱随着Ca^2 离子浓度的增加逐渐接近于Sr2CeO4(Ⅱ)的激发光谱．激发主峰带应属于CeO6八面体终端Ce^4 -O^2-键的电荷迁移带．对于激发光谱中340nm左右的弱激发峰，其峰值波长不受形成机理及Ca^2 掺杂的影响，只是其强度随着激发主峰的红移而增加，它可能属于CeO6八面体平面上Ce^4 -O^2-键的电荷迁移带．形成机理及Ca^2 掺杂对发射光谱没有影响．Ca^2 在Sr2CeO4(Ⅱ)与Ba^2 在Sr2CeO4(Ⅰ)和(Ⅱ)中均难于替代Sr^2 的位置．     

复合氧化物SrEu2O4的合成与光谱特性

以SrCO3和Eu2O3为原料,采用高温固相反应法在空气气氛中合成了一种Eu和Sr的复合氧化物.利用XRD,TG/DTA和荧光光谱等测试手段对该种新物相的组成、结构和发光性质进行了研究.XRD结果显示,该物相的分子式组成为SrEuO4,与BaEu2O4同构.荧光光谱表明,SrEu2O4存在一个双峰结构的Eu3 -O2-电荷迁移带,峰值分别位于257和280 nm;在紫外光激发下,SrEu2O4以5D0→7F2电偶极发射跃迁(618 nm)最强,发出强的红光.     

Dy含量对红色长余辉发光材料Sr3Al2O6:Eu2+,Dy3+性能的影响

采用溶胶凝胶法制备了Sr3Al2O6:Eu2+,Dy3+红色长余辉发光材料,利用X射线衍射仪对材料的物相进行了分析,结果表明,1200℃下制备的样品的物相为Sr3Al2O6,少量的Eu和Dy掺杂没有影响样品的相组成.采用荧光分光光度计、照度计测定了样品的发光特性.结果表明Sr3Al2O6:Eu2+和Sr3Al2O6:Eu2+,Dy3+的激发光谱均为激发峰位于473 nm的宽带谱.Sr3Al2O6:Dy3+的发射峰位于530.1 nm,对应于Dy3+代替Sr2+位置后基质中形成的施主-受主对Dy·Sr-V″Sr的重新组合.Sr3-0.02-yAl2O6:0.02Eu2+,yDy3+(0相似文献   

溶胶-凝胶法合成Sr2CeO4及其发光性能的研究

采用Pechini溶胶－凝胶法合成了Sr2CeO4粉末。利用X射线衍射（XRD）、扫描电镜（SEM）、热重及差热分析（TG－DTA）以及发光光谱等测试手段对Sr2CeO4的结晶过程、发光性质进行了研究。XRD结果表明，用Pechini溶胶－凝胶法合成的样品800℃时已开始结晶，900℃时可得到三斜晶系的Sr2CeO4多晶粉末。扫描电镜照片可以看出颗粒大小不均匀，粒径约为1－5μm。发光光谱测试表明Sr2CeO4粉末的激发光谱是一个宽带双峰结构，分别位于310nm和340nm。这个宽带属于Ce^4 的电荷迁移带。用340nm激发样品，其发射光谱也是一个宽带，最大峰位于475nm，这个峰属于Ce^4 的f→t1g跃迁。用310nm激发得到的发射光谱与用340nm激发得到的发射光谱相同。     

白光LED用红色荧光粉CeO_2∶Eu~(3+)的光谱性能研究

使用共沉淀法制备不同掺杂浓度的CeO2∶Eu3+的荧光粉,并利用XRD,激发和发射光谱对其光学性质进行了研究。PL激发光谱中出现300~400nm的源于基质CeO2的强吸收宽带以及较弱的Eu3+的7 F0-5 D2(467nm)吸收峰。由于Ce4+和Eu3+半径十分接近,因而Eu3+在CeO2中具有较高的固溶度。当高浓度Eu3+掺杂CeO2时,出现了7F0-5 D2(467nm)吸收峰的极大增强。在467nm激发下获得了Eu3+的5 D0—7 F1(592nm)和5 D0—7 F2(612nm)跃迁的特征红光发射。与电荷迁移带激发下获得的红光相比,在467nm蓝光激发下获得的红光强度是其5倍。7 F0—5 D2(467nm)的强电子吸收与蓝光LED芯片的输出波长相匹配,在蓝光激发下获得明亮的红光发射。因此,Eu3+掺杂CeO2荧光粉是一种有潜力的用于白光LED的红色荧光粉。     

SrCO3:Mn2+绿色荧光粉的合成和发光性能

采用共沉淀法结合高温固相法,在碳还原气氛下合成了SrCO3:Mn2+绿色荧光粉,用XRD和荧光光谱分别对样品的结构和发光性能进行了表征.XRD结果证实,样品为单一斜方晶系的SrCO3相;荧光光谱检测表明,样品在267nm左右紫外线激发下,产生峰位位于547 nm的明亮绿光,对应于Mn2+的4T1(4G)→6A1(6S)电子跃迁.样品的最佳烧结温度为1 000℃,Mn2+的最佳掺杂摩尔分数为2.0%.     

SrCO3:Mn2+绿色荧光粉的合成和发光性能

采用共沉淀法结合高温固相法,在碳还原气氛下合成了SrCO3:Mn2+绿色荧光粉,用XRD和荧光光谱分别对样品的结构和发光性能进行了表征.XRD结果证实,样品为单一斜方晶系的SrCO3相;荧光光谱检测表明,样品在267nm左右紫外线激发下,产生峰位位于547 nm的明亮绿光,对应于Mn2+的4T1(4G)→6A1(6S)...     

Si基CeO_2薄膜的发光特性

利用电子束蒸发技术在p型硅衬底上沉积了200 nm厚的CeO2薄膜样品,将样品置于弱还原气氛中高温退火后,观察到薄膜在385,418 nm以及445 nm左右出现三个明显的发光峰。结合激发光谱、吸收光谱以及XRD分析表明:CeO2薄膜在高温下容易发生失氧反应,出现Ce4+→Ce3+离子转变,Ce3+离子在紫外光的激发下,电子由O2p跃迁到5d能级,再由5d能级向4f能级跃迁,从而产生强烈的蓝紫外发射,而445 nm左右的发光峰则来自于SiO2薄膜的缺陷发光。样品选择900~1 200℃不同温度退火,并且在1 200℃下进行了不同时间的退火。研究结果显示:在1 200℃下进行2 h的退火,薄膜发光强度达到最大。     

K_2ZnSiO_4∶Eu~(3+)红色荧光粉的制备及发光性能

采用高温固相法合成了适合近紫外光、蓝光激发的K2ZnSiO4∶Eu3+红色荧光粉,研究了该荧光粉的发光特性。XRD结果显示,所合成的荧光粉主晶相为K2ZnSiO4。样品的激发光谱由O2-→Eu3+电荷迁移带(200~350nm)和Eu3+离子的特征激发峰(350~500nm)组成,最强峰位于396nm,次强峰位于466nm。在396nm和466nm激发下,样品均呈多峰发射,分别由Eu3+离子的5D0→7FJ(J=0,1,2,3,4)能级跃迁产生,其中619nm处峰值最大。增加Eu3+离子的掺杂浓度,荧光粉的发光逐渐增强。在实验测定的浓度范围内,未出现浓度猝灭现象。不同Eu3+浓度样品的色坐标均位于色品图红光区,非常接近NTSC标准。     

新型黄绿色荧光粉BaMoO_4:Pr~(3+)的制备与光致发光性质研究

采用高温固相法成功合成了新型BaMoO4:Pr3+黄绿色荧光材料,并对其晶体结构、形貌和发光性质进行了研究。X射线衍射(XRD)测试结果表明在1300℃制备的样品具有白钨矿类结构晶体,样品的形貌在扫描电镜(SEM)显示下呈不规则外形。荧光样品激发光谱由强的电荷迁移跃迁(CT)带和Pr3+离子的特征激发峰组成,主激发峰位于447nm(3 H4→3P2)、472nm(3 H4→3P1)和485nm(3 H4→3P0);其发射谱峰分别位于527nm(3P1→3 H4,5)、542nm和551nm(3P0→3 H5)、596nm(1 D2→3 H4)、614nm(3P0→3 H6)和642nm(3P0→3F2),最强发射峰位于642nm处。获得Pr3+的最佳掺杂摩尔分数为0.2%~0.3%。研究表明:BaMoO4:Pr3+是一种有望应用于蓝光发光二极管(LED)有效激发的黄绿色荧光粉材料。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.