Characteristics of SrBi2Ta2O9 ferroelectric films in an in situ applied low electric field prepared by metalorganic decomposition

SrBi₂Ta₂O₉ (SBT) films were prepared on Pt/TiO₂/SiO₂/Si substrates at 750 °C in oxygen by metalorganic decomposition method. A low electric field was in situ applied during the film crystallization. It was first found that a low electric field and its direction have significant influence on the microstructures and ferroelectric properties of SBT films. Under a positive electric field (assuming that the bottom electrode is electrically grounded), the films show stronger c-axis-preferred orientation than without electric field and under a negative electric field. As a possible origin is proposed that the interface-induced nucleation growth between SBT and Pt coated substrate with application of low electric field plays a key role. Above all, an in situ applied low electric field during the film crystallization is a promising technique controlling film orientation for film preparation by wet chemical method.     

C-V studies on metal-ferroelectric bismuth vanadate (Bi2VO5.5)-semiconductor structure

Ferroelectric bismuth vanadate Bi₂VO_5.5 (BVO) thin films have been successfully grown on p-type Si(100) substrate by using chemical solution decomposition (CSD) technique followed by rapid thermal annealing (RTA). The crystalline nature of the films has been studied by X-ray diffraction (XRD). Atomic force microscopy (AFM) was used to study the microstructure of the films. The dielectric properties of the films were studied. The capacitance-voltage characteristics have been studied in metal-ferroelectric-insulator-semiconductor (MFIS) configuration. The dielectric constant of BVO thin films formed on Si(100) is about 146 measured at a frequency of 100 kHz at room temperature. The capacitance-voltage plot of a Bi₂VO_5.5 MFIS capacitor subjected to a dc polarizing voltages shows a memory window of 1.42 V during a sweep of ±5 V gate bias. The flatband voltage (V_f) shifts towards the positive direction rather than negative direction. This leads to the asymmetric behavior of the C-V curve and decrease in memory window. The oxide trap density at a ramp rate of 0.2 V/s was estimated to be as high as 1.45×10¹² cm⁻².     

Enhanced ferroelectric property of (Pb0.95Ca0.05)(Nb0.02Zr0.80Ti0.20)O3 thin films prepared by RF magnetron sputtering

(Pb_0.95Ca_0.05)(Nb_0.02Zr_0.80Ti_0.20)O₃ [PCNZT] thin films were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering with and without a LaNiO₃ [LNO] buffer layer. Ca and Nb elements in PZT films enhance the ferroelectric property, LaNiO₃ buffer layer improves the crystal quality of the PCNZT thin films. PCNZT thin films possess better ferroelectric property than that of PZT films for Ca and Nb ion substitution, moreover, PCNZT thin films with a LNO buffer layer possess (1 0 0) orientation and good ferroelectric properties with high remnant polarization (P_r = 38.1 μC/cm²), and low coercive field (E_c = 65 kV/cm), which is also better than that of PCNZT thin films without a LNO buffer layer (P_r = 27.9 μC/cm², E_c = 74 kV/cm). The result shows that enhanced ferroelectric property of PZT films can be obtained by ion substitution and buffer layer.     

Microstructure and dielectric properties of (Ba0.6Sr0.4)TiO3 thin films grown on super smooth glazed-Al2O3 ceramics substrate

Modified substrates with nanometer scale smooth surface were obtained via coating a layer of CaO-Al₂O₃-SiO₂ (CaAlSi) high temperature glaze with proper additives on the rough-95% Al₂O₃ ceramics substrates. (Ba_0.6Sr_0.4)TiO₃ (BST) thin films were deposited on modified Al₂O₃ substrates by radio-frequency magnetron sputtering. The microstructure, dielectric, and insulating properties of BST thin films grown on glazed-Al₂O₃ substrates were investigated by X-ray diffraction (XRD), atomic force microscope (AFM), and dielectric properties measurement. These results showed that microstructure and dielectric properties of BST thin films grown on glazed-Al₂O₃ substrates were almost consistent with that of BST thin films grown on LaAlO₃ (1 0 0) single-crystal substrates. Thus, the expensive single-crystal substrates may be substituted by extremely cheap glazed-Al₂O₃ substrates.     

Enhanced ferroelectric properties of (Pb0.90La0.10)Ti0.975O3 multilayered thin films prepared by RF magnetron sputtering

The (Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PLT/PT), PbTiO₃/(Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PT/PLT/PT) multilayered thin films with a PbO_x buffer layer were in situ deposited by RF magnetron sputtering at the substrate temperature of 600 °C. With this method, highly (1 0 0)-oriented PLT/PT and PT/PLT/PT multilayered thin films were obtained. The PbO_x buffer layer leads to the (1 0 0) orientation of the films. The dielectric, ferroelectric and pyroelectric properties of the PLT multilayered thin films were investigated. It is found that highly (1 0 0)-oriented PT/PLT/PT multilayered thin films possess higher remnant polarization 2P_r (44.1 μC/cm²) and better pyroelectric coefficient at room temperature p (p = 2.425 × 10⁻⁸ C/cm² K) than these of PLT and PLT/PT thin films. These results indicate that the design of the PT/PLT/PT multilayered thin films with a PbO_x buffer layer should be an effective way to enhance the dielectric, ferroelectric and pyroelectric properties. The mechanism of the enhanced ferroelectric properties was also discussed.     

Multiferroic properties of Bi0.8La0.2FeO3/CoFe2O4 multilayer thin films

Bi_0.8La_0.2FeO₃/CoFe₂O₄ (BLFO/CFO) multilayer thin films (totally 20 layers BLFO and 19 layers CFO) were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and transmission electron microscope measurements show that the films are polycrystalline and consisted of multilayered structure. Ferroelectric hysteresis loops with remnant polarization and saturated polarization of 4.2 and 13.3 μC/cm², respectively, were observed. On the other hand, the films show well-shaped magnetization hysteresis loops with saturated and remnant magnetization of 34.7 and 11.4 emu/cm³, respectively, which are significantly larger than pure BLFO thin films deposited under the same conditions. These results indicate that constructing epitaxial superlattice might be a promising way to fabricate multiferroics with improved properties.     

Switching phenomenon and optical properties of Se85Te10Bi5 films

Se₈₅Te₁₀Bi₅ films of different thicknesses ranging from 126 to 512 nm have been prepared. Energy-dispersive X-ray (EDX) spectroscopy technique showed that films are nearly stoichiometric. X-ray diffraction (XRD) measurements have showed that the Se₈₅Te₁₀Bi₅ films were amorphous. Electrical conduction activation energy (ΔE_σ) for the obtained films is found to be 0.662 eV independent of thickness in the investigated range. Investigation of the current voltage (I-V) characteristics in amorphous Se₈₅Te₁₀Bi₅ films reveals that it is typical for a memory switch. The switching voltage V_th increases with the increase of the thickness and decreases exponentially with temperature in the range from 298 to 383 K. The switching voltage activation energy (ε) calculated from the temperature dependence of V_th is found to be 0.325 eV. The switching phenomenon in amorphous Se₈₅Te₁₀Bi₅ films is explained according to an electrothermal model for the switching process. The optical constants, the refractive index (n) and the absorption index (k) have been determined from transmittance (T) and reflectance (R) of Se₈₅Te₁₀Bi₅ films. Allowed non-direct transitions with an optical energy gap (E_g^opt) of 1.33 eV have been obtained. ΔE_σ is almost half the obtained value of E_g^opt, which suggested band to band conduction as indicated by Davis and Mott.     

Influence of crystallization on the spectral features of nano-sized ferroelectric barium strontium titanate (Ba0.7Sr0.3Tio3) thin films

Ferroelectric barium strontium titanate (Ba_0.7Sr_0.3TiO₃)(BST) thin films have been prepared from barium 2-ethylhexanoate [Ba[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂]_, strontium 2-ethylhexanoate [Sr[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂] and titanium(IV) isopropoxide [TiOCH(CH₃)₂]₄ precursors using a modified sol-gel technique. The precursor except [TiOCH(CH₃)₂]₄ were synthesized in the laboratory. Transparent and crack-free films were fabricated on pre-cleaned quartz substrates by spin coating. The structural and optical properties of films annealed at different temperatures have been investigated. The as-fired films were found to be amorphous that crystallized to the tetragonal phase after annealing at 550 °C for 1 h in air. The lattice constants “a” and “c” were found to be 3.974 A and 3.990 A, respectively. The grain sizes of the films annealed at 450, 500 and 550 °C were found to be 30.8, 36.0 and 39.8 nm respectively. The amorphous film showed very high transparency (∼95%), which decreases slightly after crystallization (∼90%). The band gap and refractive index of the amorphous and crystalline films were estimated. The optical dispersion data are also analyzed in the light of the single oscillator model and are discussed.     

A combinatorial approach to the discovery and optimization of YCa4O(BO3)3-based luminescent materials

Thin films of YCa₄O(BO₃)₃ (YCOB)-based new luminescent materials were explored by the combinatorial pulsed laser deposition (PLD) method which enabled us to fabricate continuous composition spread film libraries. Strong red and green luminescence were found in the Y_1−xEu_xCOB (0 ≤ x ≤ 1), (YEuCOB) and Y_1−yTb_yCOB (0 ≤ y ≤ 1) (YTbCOB) films, respectively. The film libraries were characterized by photoluminescence (PL), PL decay, an electron-probe microanalyzer and an electron diffraction analysis. The luminescent intensities in the amorphous film libraries strongly depended on the chemical composition of each rare-earth (RE) ion. The optimum concentration of rare-earth ions in YEuCOB and YTbCOB were experimentally determined to be Eu = 7.5% and Tb = 20-30%, respectively.     

A comparative study of the physical properties of Sb2S3 thin films treated with N2 AC plasma and thermal annealing in N2

As-deposited antimony sulfide thin films prepared by chemical bath deposition were treated with nitrogen AC plasma and thermal annealing in nitrogen atmosphere. The as-deposited, plasma treated, and thermally annealed antimony sulfide thin films have been characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy, scanning electron microscopy, atomic force microscopy, UV-vis spectroscopy, and electrical measurements. The results have shown that post-deposition treatments modify the crystalline structure, the morphology, and the optoelectronic properties of Sb₂S₃ thin films. X-ray diffraction studies showed that the crystallinity of the films was improved in both cases. Atomic force microscopy studies showed that the change in the film morphology depends on the post-deposition treatment used. Optical emission spectroscopy (OES) analysis revealed the plasma etching on the surface of the film, this fact was corroborated by the energy dispersive X-ray spectroscopy analysis. The optical band gap of the films (E_g) decreased after post-deposition treatments (from 2.36 to 1.75 eV) due to the improvement in the grain sizes. The electrical resistivity of the Sb₂S₃ thin films decreased from 10⁸ to 10⁶ Ω-cm after plasma treatments.     

Effects of substrates on the structure and dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films

Ba(Sn_0.15Ti_0.85)O₃ (BTS) thin films were grown on Pt(1 1 1)/Ti/SiO₂/Si and LaNiO₃(LNO)/Pt(1 1 1)/Ti/SiO₂/Si substrates by a sol-gel processing technique, respectively. The BTS thin films deposited on annealed Pt(1 1 1)/Ti/SiO₂/Si and annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrates exhibited strong (1 1 1) and perfect (1 0 0) orientations, respectively. The BTS thin films grown on un-annealed Pt(1 1 1)/Ti/SiO₂/Si substrates showed random orientation with intense (1 1 0) peak, while the films deposited on un-annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrate exhibited random orientation with intense (1 0 0) peak, respectively. The dielectric constant of the BTS films deposited on annealed Pt(1 1 1)/Ti/SiO₂/Si, annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si, un-annealed Pt(1 1 1)/Ti/SiO₂/Si and un-annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrates was 512, 565, 386 and 437, respectively, measured at a frequency of 100 kHz. A high tunability of 49.7% was obtained for the films deposited on annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrate, measured at the frequency of 100 kHz with an applied electric field of 200 kV/cm. The high tunability has been attributed to the (1 0 0) texture of the films and larger grain sizes.     

Crystallization-dependent magnetic properties of Mn1.56Co0.96Ni0.48O4 thin films

The effects of magnetic property dependence of the Mn_1.56Co_0.96Ni_0.48O₄ (MCN) films on crystallization are investigated in the growth temperature of 450-750 °C. With the growth temperature increase, both the crystalline quality and the grain size improve. The MCN films exhibit paramagnetic to ferromagnetic transition and the paramagnetic parts fit to the modified Curie-Weiss law. The ferromagnetic couplings of the magnetic ions in the MCN films enhance at elevated growth temperature. The saturation magnetization at 5 K increases with increasing growth temperature, but coercive field decreases monotonously. The magnetic properties of the MCN films strongly depend on their microstructures.     

c-Axis orientation control of YBa2Cu3O7−x films grown on inclined-substrate-deposited MgO-buffered metallic substrates

Biaxially textured YBa₂Cu₃O_7−x (YBCO) films were grown on non-textured metal substrates with inclined-substrate-deposited (ISD) MgO as template. The biaxial texture feature of the films was examined by X-ray pole-figure analysis, φ-scan, and 2θ-scan. A tilt angle of 32° of the MgO[001] with respect to the substrate normal was observed. Epitaxial growth of YBCO films with c-axis tilt angle of 32° with respect to the substrate normal was obtained on these substrates with SrTiO₃(STO) as buffer layer. Whereas, by choosing yttria-stabilized ZrO₂ and CeO₂ instead of STO as buffer layer, a c-axis untilted YBCO film was obtained. Higher values of T_c=91 K and J_c=5.5×10⁵ A/cm² were obtained on the c-axis untilted YBCO films with 0.46 μm thickness at 77 K in zero field. Comparative studies revealed a unique role of CeO₂ in controlling the orientation of the YBCO films grown on ISD-MgO buffered metal substrates.     

Optical and structural studies on Ba(Mg1/3Ta2/3)O3 thin films obtained by radiofrequency assisted pulsed plasma deposition

Single-phase Ba(Mg_1/3Ta_2/3)O₃ thin films were prepared by radiofrequency plasma beam assisted pulsed laser deposition (RF-PLD) starting from a bulk ceramic target synthesized by solid state reaction. Atomic force microscopy, X-ray diffraction and spectroscopic ellipsometry were used for morphological, structural and optical characterization of the BMT thin films. The X-ray diffraction spectra show that the films exhibit a polycrystalline cubic structure. From spectroscopic ellipsometry analysis, the refractive index varies with the thin films deposition parameters. By using the transmission spectra and assuming a direct band to band transition a band gap value of ≈4.72 eV has been obtained.     

Electrical behavior of BaZr0.1Ti0.9O3 and BaZr0.2Ti0.8O3 thin films

BaZr_0.1Ti_0.9O₃ and BaZr_0.2Ti_0.8O₃ (BZT) thin films were deposited on Pt/Ti/LaAlO₃ (1 0 0) substrates by radio-frequency magnetron sputtering, respectively. The films were further annealed at 800 °C for 30 min in oxygen. X-ray diffraction θ-2θ and Φ-scans showed that BaZr_0.1Ti_0.9O₃ films displayed a highly (h 0 0) preferred orientation and a good cube-on-cube epitaxial growth on the LaAlO₃ (1 0 0) substrate, while there are no obvious preferential orientation in BaZr_0.2Ti_0.8O₃ thin films. The BaZr_0.1Ti_0.9O₃ films possess larger grain size, higher dielectric constant, larger tunability, larger remanent polarization and coercive electric field than that of BaZr_0.2Ti_0.8O₃ films. Whereas, BaZr_0.1Ti_0.9O₃ films have larger dielectric losses and leakage current density. The results suggest that Zr⁴⁺ ion can decrease dielectric constant and restrain non-linearity. Moreover, the enhancement in dielectric properties of BaZr_0.1Ti_0.9O₃ films may be attributed to (1 0 0) preferred orientation.     

Structure, magnetic and electrical transport properties of cosputtered Fe0.5Ge0.5 nanocomposite films

Fe_0.5Ge_0.5 nanocomposite films with different film thicknesses were fabricated using cosputtering. The films are composed of Ge, Fe and Fe₃Ge₂, and are ferromagnetic at room temperature. The saturation magnetization and magnetic interaction including dipolar interaction and exchange coupling increase with the increasing film thickness. The electrical conductance mechanism turns from metallic to semiconducting and the saturation Hall resistivity ρ_xys increases with the decreasing film thickness. At 28 nm, ρ_xys is ∼137 μΩ cm at 2 K, about 150 times larger than that of pure Fe film (0.9 μΩ cm) and four orders larger than that of bulk Fe. The ρ_xy-H curves of all the films show the same linearity character in low-field range even though the temperature-independent slope is different at different film thicknesses. At high temperatures, the skew scattering mechanism is dominant. At low temperatures, side-jump effect should be dominant at large resistivity ρ_xx regime for the thin films, and the skew scattering is dominant at small ρ_xx regime for the thick films.     

Magnetic,structural and electrical properties of ordered and disordered Co50Fe50 films

Co₅₀Fe₅₀ films with thickness varying from 100 to 500 Å were deposited on a glass substrate by sputtering process, respectively. Two kinds of CoFe films were studied: one was the as-deposited film, and the other the annealed film. The annealing procedure was to keep the films at 400 °C for 5 h in a vacuum of 5×10⁻⁶ mbar. From the X-ray study, we find that the as-deposited film prefers the CoFe(1 1 0) orientation. Moreover, the body-centered cubic (bcc) CoFe(1 1 0) line is split into two peaks: one corresponding to the ordered body-centered tetragonal (bct) phase, and the other, the disordered bcc phase. After annealing, the peak intensity of the ordered bct phase becomes much stronger, while that of the disordered bcc phase disappears. The annealing has also caused the ordered CoFe(2 0 0) line to appear. When the amount of the ordered bct phase in Co₅₀Fe₅₀ is increased, the saturation magnetization (M_s) and coercivity (H_c) become larger, but the electrical resistivity (ρ) decreases. From the temperature coefficient of resistance (TCR) measurement, we learn that the bct grains in the CoFe film start to grow at temperature 82 °C.     

Dependence of magnetic anisotropy of the La0.67Ca0.33MnO3 films on substrate and film thickness

Strain in the La_0.67Ca_0.33MnO₃ films has been tuned by varying substrate and film thickness, and its effects on magnetic anisotropy are studied based on the measurements of isothermal magnetization. Measuring the strain in the films by the out-of-plane lattice parameter (c), we found a strong dependence of the magnetic anisotropy constant (Ku) on strain. Ku decreases linearly from ∼−1.1×10⁶ erg/cm³ for c=0.763 nm to 1.2×10⁶ erg/cm³ for c=0.776 nm, corresponding to a change from tensile strain to compressive strain. Positive Ku signifies a uniaxial anisotropy with the easy axis perpendicular to the film plane, while negative Ku demonstrates an anisotropy of the easy plane character. Smaller or larger c leads a decrease or increase in Ku, which indicates the presence of other effects in addition to those associated with strain. Three distinctive processes for the magnetization are observed along the hard magnetic axis of the films on (001)SrTiO₃, suggesting a possibility of strain relaxation even in ultra-thin films.     

Exchange bias and negative magnetoresistance in [Co/Bi/Co]/IrMn thin films]

The artificial control of grain-boundary resistance and its contribution to magnetic and magneto-transport properties in [Co(3 nm)/Bi(2.5 nm)/Co(3 nm)]Ir₂₀Mn₈₀(12 nm) thin films that exhibit exchange bias is studied. Transverse magnetoresistance (MR) loops exhibit a negative MR in thin films grown by magnetron sputtering on Si/SiN_x(100 nm) substrates. This negative MR effect is of the giant-MR (GMR) type, although its magnitude is less than 1%. A considerable exchange bias (EB) effect is observed only at lower temperatures, where both, GMR and isothermal magnetization loops exhibit a shift of −600 Oe at 5 K.     

Structure and electrical properties of CdIn2O4 thin films prepared by DC reactive magnetron sputtering

CdIn₂O₄ thin films were prepared by direct-current (DC) reactive magnetron sputtering. The structure, surface morphology and the chemical composition of the thin films were analyzed by X-ray diffraction (XRD), atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS), respectively. The electrical properties of the films prepared in different oxygen concentration and annealing treatment were determined, and the effects of the preparing conditions on the structure and electrical properties were also explored. It indicates that the CdIn₂O₄ thin films with uniform and dense surface morphology contain mainly CdIn₂O₄, In₂O₃ phases, and CdO phase is also observed. The XPS analysis confirms the films are in oxygen-deficient state. The electrical properties of these films significantly depend on the preparing conditions, the resistivity of the films with the oxygen concentration of 4.29% is 2.95 × 10⁻⁴ Ω cm and the Hall mobility is as high as 60.32 cm²/V s. Annealing treatment can improve the electrical performance of the films.