A new organic semiconducting polymer from Cu2+ chelate of poly(vinyl alcohol)and iodine

A new, easily processed, organic semiconductor was prepared from poly(vinyl alcohol) (PVA). The Cu²⁺ chelate of PVA exhibited excellent surface resistivity around 10³ Ω cm^?2 when modified with iodine. Favorable conditions for preparing the chelate effective for the conduction were investigated. The resistivity was significantly affected by the amounts of cupric salts and iodine, satisfactory results being given by more than 15 wt% of cupric salts and about 4 wt% of iodine. Effects of molecular weight of PVA and the chelate structure were also studied.     

Study on correlation of morphology of electrospun products of polyacrylamide with ultrahigh molecular weight

Polyacrylamide (PAAm) with ultrahigh molecular weight of 9 × 10⁶ g/mol has been processed by means of electrospinning, to afford products with a variety of morphologies, including polymer colloids, beaded fibers, smooth fibers, and ribbons. These morphologies can be controlled by a minute change of solution concentration in a small concentration range (0.3–3.0 wt %), because of the high molecular weight of the polymer. Under our experimental conditions, no electrospun product was obtained at the concentrations below 0.3 wt %. Beaded fibers and smooth fibers formed at the concentrations between 0.3 and 0.7 wt %. At concentrations between 0.7 and 2.0 wt %, smooth fibers and ribbons coexisted. At concentrations above 2.0 wt %, ribbons were the only product. Special morphologies such as triangular beads, helical fibers, and zigzag ribbons were also observed. With a lower molecular weight PAAm, branched fibers were found in the product. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2190–2195, 2005     

Nuclear magnetic resonance relaxation studies of polyacrylamide solution

 The cohesive interaction among polymer chains in a polyacrylamide (PAAm)–D₂O solution has been studied by NMR relaxation. The NMR relaxation times of PAAm in the good solvent D₂O were measured at different temperatures. The results show that the solution system has a high local viscosity and that its relaxation characteristic is soft-solid-like. The temperature dependence of the relaxation behavior of the solution is obviously different from that of ordinary polymer solutions. The difference lies in the relaxation behavior of the methylene protons in the main chain of PAAm, as shown by analyzing the relaxation process with single exponential and biexponential decays. As the temperature increases, the solvation is weakened, leading polymer chains to form curling coils, thus hindering the movement of the methylene protons among the main chains. It can be expected from the existence of 80% fast-relaxing protons that there are a zhigh number of entanglements among the polymer chains in PAAm solution. The information about entanglements among the polymer chains can be deduced from the biexponential dependence of the spin–spin relaxation on the concentration of the polymer solutions. Received: 14 April 1999/Accepted in revised form: 12 October 1999     

Swelling of polyacrylamide gels in polyacrylamide solutions

Swelling behavior of polyacrylamide (PAAm) and polyacrylamide-co-polyacrylic acid (PAAm-co-PAAc) gels was investigated in aqueous solutions of monodisperse PAAms with molecular weights (M_w) ranging from 1.5 × 10³ to 5 × 10⁶ g/mol. The volume of the gels decreases as the PAAm concentration in the external solution increases. This decrease becomes more pronounced as the molecular weight of PAAm increases. The classical Flory–Huggins (FH) theory correctly predicts the swelling behavior of nonionic PAAm gels in PAAm solutions. The polymer–polymer interaction parameter χ₂₃ was found to decrease as the molecular weight of PAAm increases. The swelling behavior of PAAm-co-PAAc gels in PAAm solutions deviates from the predictions of the FH theory. This is probably due to the change of the ionization degree of AAc units depending on the polymer concentration in the external solution. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1313–1320, 1998     

Polyacrylamide gels formed with Cr+3 ion and Cr(acetate)3: Thermodynamically and kinetically controlled crosslinking reactions

The gelation of buffered aqueous Cr⁺³/polyacrylamide (PAAm) solutions has been studied over the pH range 2-11. With Cr⁺³ supplied as Cr(NO₃)₃ and a 7.5% hydrolyzed PAAm the upper limit for gelation was about pH 7, but Cr(acetate)₃/PAAm solutions gelled as high as pH 9. Evidence is presented that the formation of unreactive colloidal Cr(OH)₃(H₂O)₃, rather than polymer crosslinking, is favored thermodynamically for Cr⁺³/PAAm solutions at pH > 7. The crosslinks formed in Cr(acetate)₃/PAAm solutions at pH 7–9 are deduced to be kinetically controlled products. Independent evidence for the kinetic stability of Cr⁺³/PAAm gels above pH 7 has also been obtained. Other observations relevant to the mechanism of crosslinking of PAAm with Cr(acetate)₃ are described.     

Effect of oleic acid plasticizer on chitosan-lithium acetate solid polymer electrolytes

Plasticized polymer electrolytes composed of chitosan as the host polymer, oleic acid (OA) as the plasticizer and lithium acetate (LiOAc) as the doping salt were prepared by the solution cast technique. These complexes with different amounts of salts and plasticizers were investigated as possible ionic conducting polymers. The highest ionic conductivity of the plasticized chitosan-LiOAc was ∼10⁻⁵ S cm⁻¹ for the film containing 40.0 wt.% LiOAc and 10.0 wt.% of OA. Conductivity for the plasticized LiOAc-doped chitosan polymer was also studied as a function of temperature between 300 and 363 K. The plot of ln(σT) versus 10³/T for each sample obeys Arrhenius rule indicating the conductivity to be thermally assisted. XRD and FTIR spectroscopy techniques have been used for the structural studies.     

聚丙烯酰胺凝胶结构非均匀性的动态光散射研究

利用动态光散射技术研究了聚丙烯酰胺 (PAAm)凝胶结构的非均匀性 ,分析了PAAm凝胶结构非均匀性的形成原因及凝胶动态光散射的数据处理方法和分析结果的物理意义 .研究结果表明 ,PAAm凝胶中含有动态相关长度 (LC)不同的两相 ,其中 ,LC 为 10～ 2 0nm的区域是聚合物稀疏相 ,LC 为 85nm左右的区域是聚合物密集相 ,两相的不均匀分布形成了PAAm凝胶结构的非均匀性 .分析表明 ,PAAm凝胶存在两相主要是由于单体和交联剂的溶解度存在差异所致 .随交联度增大 ,PAAm凝胶结构的非均匀性显著增强     

Novel conjugated polymer containing anthracene backbone: Addition polymer of 9, 10-diethynylanthracene with 9, 10-anthracenedithiol and its properties

9,10-Diethynylanthracene was prepared by the alkaline hydrolysis of 9,10-bis (trimethylsilylethynyl) anthracene. Another new monomer of 9, 10-anthracenedithiol was prepared by the reduction of anthracene polydisulfide. A crystalline conjugated polymer of 9,10-diethynylanthracene with 9,10-anthracenedithiol was synthesized in a THF solution at 50°C by UV irradiation or by using radical initiators. The molecular weight (M?_n) of the insoluble polymer in THF is about 20000–30000 and the soluble is about 4000. From the sulfur content and IR spectrum of the insoluble polymer, it is realized that the obtained polymer has the alternating structure consisting of 9,10-diethynylanthracene and 9,10-anthracenedithiol units. X-ray pattern indicated that the polymer has a layer structure. The conductivity of the undoped polymer was about 10^?11S/cm, but enhanced up to 10^?6 S/cm by doping with iodine. The enhancement of the conductivity seems to be the existence of the CT complex among the polymer backbone and iodine or iodine anion.     

Ultrafast dynamics in aqueous polyacrylamide solutions.

We have investigated the ultrafast dynamics of aqueous polyacrylamide ([-CH(2)CH(CONH(2))-](n), or PAAm) solutions using femtosecond optical heterodyne-detected Raman-induced Kerr effect spectroscopy (OHD-RIKES). The observed aqueous PAAm dynamics are nearly identical for both M(w) = 1500 and 10 000. Aqueous propionamide (CH(3)CH(2)CONH(2), or PrAm) solutions were also studied, because PrAm is an exact model for the PAAm constitutional repeat unit (CRU). The longest time scale dynamics observed for both aqueous PAAm and PrAm solutions occur in the 4-10 ps range. Over the range of concentrations from 0 to 40 wt %, the picosecond reorientation time constants for the aqueous PAAm and PrAm solutions scale linearly with the solution concentration, despite the fact that the solution shear viscosities vary exponentially from 1 to 264 cP. For a given value of solution concentration in weight percent, constant ratios of measured reorientation time constants for PAAm to PrAm are obtained. This ratio of PAAm to PrAm reorientation time constants is equal to the ratio of the volume for the PAAm constitutional repeat unit (-CH(2)CHCONH(2)-) to the molecular volume of PrAm. For these reasons, we assign the polymer reorientation dynamics to motions of the entire constitutional repeat unit, not only side group motions. Simple molecular dynamics simulations of H[-CH(2)CH(CONH(2))-](7)H in a periodic box with 180 water molecules support this assignment. Amide-amide and amide-water hydrogen-bonding interactions lead to strongly oscillatory femtosecond dynamics in the Kerr transients, peaking at 80, 410, and 750 fs.     

Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

Cupric sulfate–hydrazine system as an initiator of vinyl polymerization. II. Polymerization of methyl methacrylate in aqueous solution in the absence of oxygen

The cupric sulfate–hydrazine system has been used to initiate the aqueous solution polymerization of methyl methacrylate at pH 9.25 in the absence of oxygen. There is no decomposition of hydrazine on the surface of the reduced cupric hydroxide until a flocculant precipitate is formed (cupric sulfate concentration of about 10^?3 mole/1). Below this concentration, the initiating reaction occurs solely in solution, the rate of polymerization decreasing when the reaction mixture becomes depleted in cupric ions. When a suitable surface area of the precipitated polymer is attained, adsorption and decomposition of hydrazine occurs on its surface, causing further initiation of polymerization.     

Polyacrylamide-methanesulfonic acid gel polymer electrolytes for tin-air battery

The present work describes the synthesis and characterization of gel polymer electrolytes containing methanesulfonic acid (MSA) with Polyacrylamide (PAAm). The PAAm–MSA gel electrolytes were prepared with different concentrations of MSA. Addition of 0.5 M of MSA into the electrolyte increased the ionic conductivity of PAAm from 1.35 × 10^?3 to 1.56 × 10^?2 S cm^?1. The maximum ionic conductivity of 7.0 × 10^?1 S cm^?1 was obtained with 3 M MSA at room temperature. The chemical interaction between PAAm and MSA was studied by Fourier transformed infra-red. The performance as a polymer electrolyte was evaluated from the cell discharge and open circuit potential measurements of a tin-air cell. The tin-air cell supported relatively high current, up to 12 mA cm^?2 with a maximum power density of 5 mW cm^?2. The open-circuit potential of the cell was 1.27 V for 24 h.     

High-molecular-weight poly(amino acid)s by the direct polycondensation reaction promoted by triphenyl phosphite and LiCl in the presence of polyvinylpyrrolidone

Poly(α-amino acid)s of high molecular weight were obtained by the direct polycondensation reaction of α-amino acids in the presence of polyvinylpyrrolidone (PVP) as a matrix of triphenyl phosphite and LiCl in N-methylpyrrolidone (NMP). Molecular weights of the polymer produced were improved by use of an increasing amount of matrix of higher molecular weight. Most favorable results were obtained by the reaction at 80°C for 16 hr at a monomer concentration of 0.33 mole/liter in a NMP solution that contained about 3 wt % LiCl in the presence of an equivalent unit mole of PVP with the molecular weight of 3.6 x 10⁵. The polymer from β-alanine with high molecular weight, which is difficult to obtain by the NCA method, was easily prepared by this process.     

Interactions of glucose and polyacrylamide in solutions and gels

The swelling of polyacrylamide (PAAm) gels increased with rising glucose concentrations, and so did the osmotic pressure of the soluble polymer and its intrinsic viscosity. A Flory–Huggins‐based model for the osmotic pressure of a nonionic hydrophilic polymer in a ternary solution consisting of a main solvent, a polymer, and a nondissociating low‐molecular‐weight cosolute was developed and examined. The model‐calculated values were in reasonably good agreement with experimental results for the water–PAAm–glucose system studied when PAAm–water and glucose–water interaction coefficients from the binary systems were used, and only the PAAm–glucose interaction coefficient was adjusted. Its negative value suggested a favorable interaction of glucose and PAAm, supporting the notion of glucose being a good cosolvent for PAAm. Isothermal titration microcalorimetry results showed no evidence for the binding of glucose to PAAm, but an exothermic interaction was indicated between glucose and PAAm. Microcalorimetrically determined enthalpic contributions to the Flory–Huggins interaction coefficients showed enthalpically favorable binary interactions, particularly the enthalpic component of the PAAm–glucose interaction coefficient (χ_H23), which was slightly negative. The enthalpically favorable interaction between glucose and PAAm may explain the increased osmotic pressure of PAAm in glucose solutions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3053–3063, 2003     

Studies on stable aqueous poly(o-toluidine) prepared with the use of a water soluble support polymer,polyacrylamide

Polymerization of o-methylaniline or o-toluidine (OT) was studied in aqueous acidic (HCl) medium with or without the use of the support of a water soluble polymer, polyacrylamide (PAAm). Poly(o- toluidine) (POT) produced with PAAm support was in the form of aqueous solution or dispersion that showed high stability and good processibility. High degree of dispersion or near solubility and storage stability of POT thus prepared are explained on the basis of establishment of hydrogen bonding between segments of POT being formed and the PAAm present in the medium thus resulting in a template effect. Studies by UV-visible spectroscopy and FTIR spectroscopy lend support to this view. POT-PAAm composites commonly show higher thermal stability than POT and the composites show DC-electrical conductivities in the range of 10⁻⁹–10⁻¹ S · cm⁻¹ depending on the POT content. Morphological analysis of the optically clear aqueous POT-PAAm solution by transmission electron microscopy (TEM) shows the presence of large clusters of PAAm-supported near-spherical POT nanoparticles in the aqueous PAAm solution. Scanning electron microscopic (SEM) analysis of isolated POT-PAAm composites shows a cocontinuous phase morphology without any trend of gross phase separation. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3243–3256, 1999     

Photometric titration of total iodine at trace levels in concetrated chloride solutions

The method is based on reduction of total iodine (10^?7?10^?5 M), to iodide with sulphite in acidic solution. The excess of sulphur dioxide is removed by bubbling with nitrogen, and the resulting solution is titrated spectrophotometrically with a standard solution of iodate, the absorbance being measured at 230 nm. Some Italian table salts, iodized or common, were analyzed for their iodide and total iodine content.     

Water determination of precursor solutions with oxidant cations by the Karl Fischer method: the YBCO-TFA case

Uncontrolled water content in non-aqueous precursor solutions can be a source of irreproducibility in thin film performance through changes in the gel network. Towards gaining control on the solution properties, water determination in metalorganic solutions of YBCO-TFA has been studied by the Karl Fischer titration in a volumetric-type unit. However, oxidizing cations usually present when preparing functional oxides by chemical solution routes severely interfere in the Karl Fischer analysis. In the case of YBCO-TFA, cupric ions in the initial solution oxidize the iodide produced in the Karl Fischer reaction back to iodine, which in turn feeds the titration reaction and consumes more water, causing a negative error in the analysis, which can be as large as 70%. However, such chemical interference of cupric salts can be modelled and quantified. A corrected Karl Fischer methodology is proposed for accurately measuring water content in YBCO-TFA solutions, which could be potentially extended to other precursor solutions containing oxidant cations.     

Interactions between inorganic salts and polyacrylamide in aqueous solutions and gels

The swelling of poly(acrylamide) (PAAm) gels and the osmotic pressure of linear PAAm in aqueous solutions were predominantly affected by anion type and increased according to the lyotropic series ranking of sodium halide anions: F^? < (H₂O) < Cl^? < Br^? < I^?. The osmotic pressure of PAAm in all examined salt solutions followed the scaling theory, with an exponent of 2.3 ± 0.1. In solutions of a sodium halide series, the value of the pre‐exponential factor seemed to depend on salt concentration, anion radius, and the apparent “anionic‐portion radius” of the water molecule. This radius, extracted from the literature data, marks a transition point of the anion radius effect. Larger anions increase the osmotic pressure of PAAm more significantly as their concentration increases and vice versa. The effects of the anions on the osmotic pressure of PAAm are related to their preferential interactions with the polymer. Iodide, which increased the osmotic pressure of PAAm with respect to its value in pure water, seemed to preferentially adsorb onto the polymer with a binding constant of K_b = 9.7 ± 2.0 M^?1 determined by isothermal titration microcalorimetry. However, fluoride, which decreased the osmotic pressure, was preferentially repulsed. The mechanisms of attraction and repulsion were attributed to ion‐water‐polymer interactions and the solvent quality of the hydrated ions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 508–519, 2003     

Radical polymerization of metal-coordinated monomers with ligands of pyrrole-containing schiff bases

The copper complexes and the cobalt complex with the ligand of 3-(2-pyrrolylmethyl-enimino)propene-1 (PIP) or p-(2-pyrrolylmethylenimino)styrene (PIS) were synthesized and homopolymerizations and the copolymerization with styrene, acrylonitrile, methyl methacrylate and acrylic acid studied. In the polymerization of chelate monomers, inhibition of radical polymerization by the central metal ion was observed, but the chelate polymer could be obtained only if the initiator was present in higher concentrations in the feed. It is considered that the strength of inhibition depends on the electronic configuration of d-orbitals of the central metal ion. The initiation mechanism of the cupric chelate monomer may be reduction of the metal ion by the redox reaction with a primary radical via the intramolecular electron transfer through the π-conjugated system of the ligand prior to the propagation step. This mechanism was verified by studying the redox reaction of various copper complexes with DPPH. In the system of the copper complex containing PIS and acylic acid the alternating copolymer could be obtained at any mole fraction of monomer mixture in feed.     

Blends of polyester having amino sulfonic acid moieties with poly(vinyl alcohol) and their metal complex formation

Polyester having amino sulfonic acid moieties (TBES) was prepared by a liquid/solid biphase polycondensation of terephthaloyl chloride (TPC) and N,N-bis(2-hydroxyethyl)-2-aminoethanesulfonic acid (BES) in trimethyl phosphate (TMP) using triethylamine (TEA) as an acid acceptor. Blends of TBES with PVA and their metal complexes with Ni²⁺ and Co²⁺ ions were prepared. A strong interaction was observed between TBES and PVA. An electric conductivity of 10⁻⁶ S cm⁻¹ was attained for the blend films containing about 5 wt % water. A coordination structure with two chelate rings is proposed for the metal complex with Ni²⁺ and Co²⁺ ions when the molar ratio of amino sulfonic acid groups in TBES to metal ions is larger than 2. Polymer blends complexed with Ni²⁺ or Co²⁺ ions result in semi-interpenetrating polymer networks from chelate formation. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3561–3569, 1997