A study of the temperature dependence of the rate constant for the reaction of O<Subscript>2</Subscript> with surface alkoxy radicals

A method for studying the reactions of surface alkoxy radicals with O₂ at temperatures of 230 to 300 K is described. Alkoxy radicals were generated directly in the cavity of an EPR spectrometer. Surface organic radicals, prepared from paraffin wax ((CH₃)₂(CH₂) _n , n = 16–20), were applied to Aerosil particles from a solution in heptane. The Aerosil sample was placed in the cavity of the EPR spectrometer in a cylindrical cup with a central hole for pumping out gases and exposed to H atoms. In this way, it is possible observe a steady increase in the EPR signal from the surface radicals. To measure the rate constant at tropospheric temperatures, the reaction tube was placed in a Teflon jacket, through which cool nitrogen vapor was pumped. The temperature in the reactor was varied from 230 to 300 K. The recorded EPR spectra belong to the (RO) _s radical. After obtaining a stable EPR signal from the surface radicals, treatment with H atoms was stopped, additional flow of O₂ was introduced ([O₂] = 10¹⁴–10¹⁶ cm⁻³), and the reaction of O₂ with the surface organic radicals was studied by monitoring the EPR signal decay. The temperature dependence of the rate constant for the (RO) _s + O₂ → HO₂ + ketone was obtained within T = 230–300 K. The extrapolation of the data to real tropospheric conditions ([O₂] = 10¹⁸ cm⁻³) was performed.     

Lithium diffusion in Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>-based electrodes: a joint analysis of electrochemical impedance,cyclic voltammetry,pulse chronoamperometry,and chronopotentiometry data

In order to establish the mechanism and to determine the parameters of lithium transport in electrodes based on lithium-vanadium phosphate (Li₃V₂(PO₄)₃), the kinetic model was designed and experimentally tested for joint analysis of electrochemical impedance (EIS), cyclic voltammetry (CV), pulse chronoamperometry (PITT), and chronopotentiometry (GITT) data. It comprises the stages of sequential lithium-ion transfer in the surface layer and the bulk of electrode material’s particles, including accumulation of lithium in the bulk. Transfer processes at both sites are of diffusion nature and differ significantly, both by temporal (characteristic time, τ) and kinetic (diffusion coefficient, D) constants. PITT data analysis provided the following D values for the predominantly lithiated and delithiated forms of the intercalation material: 10^?9 and 3 × 10^?10 cm² s^?1, respectively, for transfer in the bulk and 10^?12 cm² s^?1 for transfer in the thin surface layer of material’s particles. D values extracted from GITT data are in consistency with those obtained from PITT: 3.5–5.8 × 10^?10 and 0.9–5 × 10^?10 cm² s^?1 (for the current and currentless mode, respectively). The D values obtained from EIS data were 5.5 × 10^?10 cm² s^?1 for lithiated (at a potential of 3.5 V) and 2.3 × 10^?9 cm² s^?1 for delithiated (at a potential 4.1 V) forms. CV evaluation gave close results: 3 × 10^?11 cm² s^?1 for anodic and 3.4 × 10^?11 cm² s^?1 for cathodic processes, respectively. The use of complex experimental measurement procedure for combined application of the EIS, PITT, and GITT methods allowed to obtain thermodynamic E,c dependence of Li₃V₂(PO₄)₃ electrode, which is not affected by polarization and heterogeneity of lithium concentration in the intercalate.     

Surface modification of polycrystalline oxides (V<Subscript>2</Subscript>O<Subscript>5</Subscript>, MoO<Subscript>3</Subscript>, and WO<Subscript>3</Subscript>) irradiated with high-power ion beams

The influence of a high-power ion beam on polycrystalline oxides (V₂O₅, MoO₃, and WO₃) is investigated. Oxide irradiation with ion beams with current densities of greater than ～30 A/cm² is established to initiate changes in the color of irradiated layers and lead to surface-layer particle melting. It is demonstrated that a distinctive feature of the interaction between a high-power ion beam and V₂O₅ is the formation of surface nanosheets and nanowires whose characteristic cross-sectional size and thickness are ～1 μm and up to ～40 nm, respectively. The nanosheets are generated near emerging surface cracks if the beam current density is ～100 A/cm². Possible mechanisms of surface nanostructures formation under the action of pulsed ion beams are discussed.     

CeO<Subscript>2</Subscript> and Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> modified Ni-YSZ anode for solid oxide fuel cell

Ni sintering at high temperature (～ 800 °C) operation drastically degrades the performance of Ni-yttria-stabilized zirconia (YSZ) anode in solid oxide fuel cell (SOFC). Mixed ionic and electronic conductive oxides such as CeO₂ and Nb₂O₅ enhance the dispersion of Ni, CeO₂ enhances the redox behavior and promotes charge transfer reactions, and Nb₂O₅ increases the triple phase boundary. In the present work, anode-supported SOFC is fabricated and tested in H₂ fuel at 800 °C. YSZ and lanthanum strontium manganite (LSM)-YSZ are used as the electrolyte and composite cathode with NiO-YSZ, CeO₂-NiO-YSZ, and Nb₂O₅-NiO-YSZ as an anode. The peak power density obtained for the cell with 10% CeO₂–30% NiO-YSZ anode at the 5 and 25 h of operation is 330 and 290 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). The peak power density obtained for the cell with 10% Nb₂O₅–30% NiO-YSZ anode at the 5 and 25 h of operation is 301 and 285 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). Physical characterization has been carried to study morphology, elemental analysis, particle size, and phase formation of the fabricated anode before and after cell operation to correlate the cell performance.     

The Kinetic Mechanisms of the Trapping of Atmospheric Gases by Marine Salt Surfaces: IX. The Heat of Adsorption of Cl Atoms on the Surface of NaCl

The heterogeneous trapping of chlorine atoms on the surface of NaCl was studied using two coaxial stream reactors connected to an EPR cavity or a mass spectrometer. The kinetics of trapping was measured by the EPR method over a wide range of chlorine atom concentrations (10¹⁰–10¹³ cm^?3) at temperatures of 250–330 K. At [Cl] ≥ 10¹² cm^?3, chlorine atoms were recorded by the EPR method in the gas phase. At lower concentrations (~10¹⁰?3 × 10¹¹ cm^?3), Cl atoms were replaced with RO₂ radicals by adding hexane RH and O₂ at the entrance of the EPR cavity. This was followed by the matrix isolation of RO² in the cavity at liquid nitrogen temperature. The probability of the trapping of chlorine atoms on the chemically inactive surface of NaCl was found to increase as the concentration of Cl grew. The temperature dependence of the trapping coefficient γ was pronounced at a concentration of chlorine atoms of ~3 × 10¹⁰ cm^?3, whereas no such dependence was observed at a chlorine concentration of ~ 10¹³ cm^?3. The recombination of Cl atoms was well described by the Rideal-Eley mechanism, and the heat of adsorption of chlorine atoms on the inactive surface of NaCl was estimated at Q = 17 ± 0.6 kcal/mol. It was shown mass spectrometrically that the trapping coefficient γ of Cl atoms decreased with the time of measurements, like the partial coefficient of the formation of the HCl product, whereas the partial coefficient of the formation of the Cl₂ product, conversely, increased with the time. The characteristic time of the attainment of stationary values by all the γ coefficients weakly depended on the initial concentration of Cl and equaled several dozen seconds. Reactions of adsorbed Cl atoms formed in the trapping of NO₃ radicals by the surface of marine salt NaCl in coastal troposphere are discussed.     

Electrochemical properties of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> prepared with tartaric acid chelating agent

Lithium manganese oxide (LiMn₂O₄) has been prepared using sol-gel technique under acidic (pH = 5.8) and alkaline (pH = 9) conditions with tartaric acid as chelating agent. X-ray studies show that under acidic condition, an Mn₂O₃ peak was observed indicating the presence of impurities. No impurity was observed for LiMn₂O₄ under alkaline conditions. The particle size is mostly in the range of 124 to 185 nm from HR-TEM. The lithium diffusion coefficient, D _Li+ in LiMn₂O₄ is of the order 10^?9 cm² s^?1. By using density functional theory (DFT) calculations, structural properties have been obtained. The specific discharge capacity of the cells with LiMn₂O₄ prepared under alkaline condition and with LiMn₂O₄ prepared under acidic condition discharged at 0.5 C is in the ranges of 132 to 142 and 128 to 139 mAh g^?1, respectively.     

Effect of Fe2O3 nanoparticles on combustion of coal surrogate (Anisole): Enhanced ignition and formation of persistent free radicals

This contribution explores the effect of nanoparticles of iron (III) oxide (Fe₂O₃) on the combustion of coal surrogate, i.e., anisole, identifying the changes in ignition features as well as the occurrence of persistent organic pollutants in the initiation channels. The method applies packed-bed reactor coupled with Fourier transform infrared (FTIR) spectroscopy to quantitate the ignition temperature under typical fuel-rich conditions, in-situ electron paramagnetic resonance (EPR) to elucidate the formation of environmentally-persistent free radicals (EPFR), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) to monitor the chemisorption of organic substrates on the nanoparticles, as well as X-ray diffraction for particles characterisation (PXRD). We employ cluster-based quantum mechanical calculation to map the reaction pathway within the scope of the density functional theory. The results of Fe₂O₃-mediated combustion of anisole depict an excessive reduction in ignition temperature from 500?°C around 220?°C at λ?=?0.8. As confirmed both from EPR and DRIFTS measurements, the chemisorption of anisole on α-Fe₂O₃ surfaces follows the direct dissociation of the O–CH₃ (and OCH₂–H), leading to the formation of surface-bound phenoxy radicals at temperatures as low as 25?°C and incurring an estimated energy barrier of E_a?=?18?kJ mol^?1 and a preexponential factor of A?=?2.7?×?10¹² M^?1 s^?1. This insight applies to free-radical chain reactions that induce spontaneous fires of coal, as coal comprises ferric oxide nanoparticles, and equally to coexistence of aromatic fuels with thermodynamically reactive Fe₂O₃ surface, e.g., in fly ash, at the cooled-down tail of combustion stacks.     

On electrochemistry of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-coated LiCoO<Subscript>2</Subscript> composite cathode with improved cycle stability

LiCoO₂-based cathode does still have a powerful competition in high-end mobile electronics due to its relatively high true density (about 5.2 g/cm³). When the operation potential range is extended, the improvement in its cycle stability has attracted more attention. The extension of its operation potential can be realized by partial replacement of Co by Ni and Mn or by surface modification. However, Ni and Mn replacing partial Co results in decreased true density; for example, the true density of LiNi_0.5Mn_0.3Co_0.2O₂ is about 4.6 g/cm³. In this case, the increase in its practical energy density is impossible. As a result, the surface modification technology becomes very important to extend its operation potential range. In this article, an Al₂O₃-coated LiCoO₂ cathode was synthesized. X-ray diffraction test did not show any impurity. Scanning electron spectroscopy measurements showed that the basic microstructure of pristine LiCoO₂ grain is sustained after coating Al₂O₃. The surface characteristic of pure and Al₂O₃-coated LiCoO₂ was also analyzed using an X-ray photoelectron spectroscopy (XPS) technique. Unusual XPS peaks of O 1s, Al 2p, and Co 2p binding energy were found and may be caused by the possible H existence in crystal structure. The electrochemical behavior was systematically investigated, and the cathode was cycled at different charge cutoff voltages (4.30～4.60 V). The charge-discharge and cyclic voltammetry measurements showed an obviously improved cyclic performance after coating Al₂O₃. The electrocatalytic activity is not clearly changed before and after coating Al₂O₃. From our systematical investigation, it could be concluded that the Al₂O₃-coated LiCoO₂ cathode is suitable for practical application in the potential range of 3.70～4.50 V vs. Li/Li⁺.     

Elevated electrochemical property of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> originated from nano-sized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>

By employment of nano-sized pre-prepared Mn₃O₄ as precursor, LiMn₂O₄ particles have been successfully prepared by facile solid state method and sol-gel route, respectively. And the reaction mechanism of the used precursors of Mn₃O₄ is studied. The structure, morphology, and element distribution of the as-synthesized LiMn₂O₄ samples are characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Compared with LiMn₂O₄ synthesized by facile solid state method (SS-LMO), LiMn₂O₄ synthesized by modified sol-gel route (SG-LMO) possesses higher crystallinity, smaller average particle size (~175 nm), higher lithium chemical diffusion coefficient (1.17 × 10^?11 cm² s^?1), as well as superior electrochemical performance. For example, the cell based on SG-LMO can deliver a capacity of 85.5 mAh g^?1 at a high rate of 5 °C, and manifests 88.3% capacity retention after 100 cycles at 0.5 °C when cycling at 45 °C. The good electrochemical performance of the cell based on SG-LMO is ascribed mainly to its small particle size, high degree of dispersion, and uniform element distribution in bulk material. In addition, the lower polarization potential accelerates Li⁺ ion migration, and the lower atom location confused degree maintains integrity of crystal structure, both of which can effectively improve the rate capability and cyclability of SG-LMO.     

Detection of vortex excitations in a Bi<Subscript>2</Subscript>Sr<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>10</Subscript> crystal at temperatures above the critical temperature by EPR of the surface layer

Vortex excitations have been detected at temperatures both below and above the critical temperature when investigating local magnetic fields on the surface of a Bi₂Sr₂Ca₂Cu₃O₁₀ single crystal by means of an electron paramagnetic resonance (EPR) probe. A thin layer of a diphenyl picrylhydrazyl organic radical deposited on the crystal surface is used as the EPR probe. A narrow EPR signal makes it possible to detect weak distortions of the magnetic field appearing at T ≿ T _c. The analysis of the temperature dependences of the resonance field and the EPR linewidth is thebasis of the assumption of the vortex nature of magnetic excitations in this temperature range.     

Magnetic structure of the NiCr<Subscript>2</Subscript>O<Subscript>4</Subscript> nickel chromite

The magnetic properties of the NiCr₂O₄ chromite are investigated and compared with similar properties of the NiFe_1.1Cr_0.9O₄ nickel ferrite-chromite material. It is found for the first time that the tetrahedral (A) sublattice of the NiCr₂O₄ chromite is responsible for the total magnetic moment. Moreover, it is revealed that the NiCr₂O₄ chromite exhibits a giant magnetostriction of the paraprocess (λ _para ～ 200×10^?6) and an anomalously large volume magnetostriction (ω ～ 500×10^?6) at a temperature of 4.2 K in magnetic fields up to ～50 kOe. The inference is made that the observed paraprocess is caused by an increase in the degree of noncollinearity of the magnetic moments induced in the octahedral (B) sublattice of the NiCr₂O₄ chromite in an external magnetic field.     

Linear and nonlinear optical spectroscopy of gadolinium iron borate GdFe<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript>

The optical spectra and the second-harmonic generation (SHG) are studied in a noncentrosymmetric GdFe₃(BO₃)₄ magnet. In the region of weak absorption (α～20–400 cm^?1) below ～3 eV, three absorption bands are distinguished, which can be unambiguously assigned to forbidden electronic transitions from the ground ⁶A₁ state of the Fe³⁺ ion to its excited states ⁴T₁(～1.4 eV), ⁴T₂(～2 eV), and ⁴A₁, ⁴E(～2.8 eV). Intense absorption begins in the region above 3 eV (α～2–4×10⁵ cm^?1), where two bands at ～4.0 and 4.8 eV are observed, which are caused by allowed electric dipole charge-transfer transitions. The spectral features of SHG in the 1.2–3.0-eV region are explained by a change in the SHG efficiency caused by a change in the phase mismatch. It is shown that in the weak absorption region, phase matching can be achieved for SHG.     

The Formation of Dimeric Centers of Copper,Iron and Gadolinium in Modified Pb<Subscript>5</Subscript>Ge<Subscript>3</Subscript>O<Subscript>11</Subscript>

It is discovered that the electron paramagnetic resonance (EPR) spectrum of the doubly charged copper centers occurs in single crystals of Pb₅Ge₃O₁₁ doped with gadolinium or iron after annealing in an atmosphere containing chlorine and bromine. Similar annealing of the crystals doped with copper in a chlorine and fluorine atmosphere leads to redistribution of the intensities of the EPR spectra of two types of Cu²⁺ centers. The influence of annealing on the ongoing intensity of spectra of the dimeric triclinic centers Fe³⁺–A, Gd³⁺–A (where A represent Cl^?, Br^?, O^2?, F^?) was the subject of this research. Consideration is given to the mechanisms for changing the charge state and association of copper center with defects.     

Roles of Al-doped ZnO (AZO) modification layer on improving electrochemical performance of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> thin film cathode

Al-doped ZnO (AZO) was sputtered on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ (NCM) thin film electrode via radio frequency magnetron sputtering, which was demonstrated to be a useful approach to enhance electrochemical performance of thin film electrode. The structure and morphology of the prepared electrodes were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer, and transmission electron microscopy techniques. The results clearly demonstrated that NCM thin film showed a strong (104) preferred orientation and AZO was uniformly covered on the surface of NCM electrode. After 200 cycles at 50 μA μm^?1 cm^?2, the NCM/AZO-60s electrode delivered highest discharge capacity (78.1 μAh μm^?1 cm^?2) compared with that of the NCM/AZO-120s electrode (62.4 μAh μm^?1 cm^?2) and the bare NCM electrode (22.3 μAh μm^?1 cm^?2). In addition, the rate capability of the NCM/AZO-60s electrode was superior to the NCM/AZO-120s and bare NCM electrodes. The improved electrochemical performance can be ascribed to the appropriate thickness of the AZO coating layer, which not only acted as HF scavenger to keep a stable electrode/electrolyte interface but also reduced the charge transfer resistance during cycling.     

EPR and optical absorption studies of Cu<Superscript>2+</Superscript> ions in [ZnPd(CN)<Subscript>4</Subscript>(C<Subscript>4</Subscript>H<Subscript>12</Subscript>N<Subscript>2</Subscript>O<Subscript>2</Subscript>)] single crystals

A Cu²⁺-doped single crystal of catena-trans-bis(N-(2-hydroxyethyl)-ethylenediamine) zinc(II)-tetra-m-cyanopaladate(II) [ZnPd(CN)₄(C₄H₁₂N₂O₂)] complex has been investigated by electron paramagnetic resonance (EPR) technique at room temperature. EPR spectra indicate that Cu²⁺ ions substitute for magnetically equivalent Zn²⁺ ions and form octahedral complexes in [ZnPd(CN)₄(C₄H₁₂N₂O₂)] hosts. The crystal field affecting the Cu²⁺ ion is nearly axial. The optical absorption studies show two bands at 322 nm (30864 cm⁻¹) and 634 nm (15337 cm⁻¹) which confirm the axial symmetry. The spin Hamiltonian parameters and the relevant wave function are determined.     

Facile one-pot synthesis of cellulose nanocrystal-supported hollow CuFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles as efficient catalyst for 4-nitrophenol reduction

A facile and efficient one-pot method for the synthesis of well-dispersed hollow CuFe₂O₄ nanoparticles (H-CuFe₂O₄ NPs) in the presence of cellulose nanocrystals (CNC) as the support was described. Based on the one-pot solvothermal condition control, magnetic H-CuFe₂O₄ NPs were in-situ grown on the CNC surface uniformly. TEM images indicated good dispersity of H-CuFe₂O₄ NPs with uniform size of 300 nm. The catalytic activity of H-CuFe₂O₄/CNC was tested in the catalytic reduction of 4-nitrophenol (4-NP) in aqueous solution. Compared with most CNC-based ferrite catalysts, H-CuFe₂O₄/CNC catalyst exhibited an excellent catalytic activity toward the reduction of 4-NP. The catalytic performance of H-CuFe₂O₄/CNC catalyst was remarkably enhanced with the rate constant of 3.24 s^?1 g^?1, which was higher than H-CuFe₂O₄ NPs (0.50 s^?1 g^?1). The high catalytic activity was attributed to the introduction of CNC and the special hollow mesostructure of H-CuFe₂O₄ NPs. In addition, the H-CuFe₂O₄/CNC catalyst promised good conversion efficiency without significant decrease even after 10 cycles, confirming relatively high stability. Because of its environmental sustainability and magnetic separability, H-CuFe₂O₄/CNC catalyst was shown to indicate that the ferrite nanoparticles supported on CNC were acted as a promising catalyst and exhibited potential applications in numerous ferrite based catalytic reactions.

Open image in new window

Graphical abstract ?

     

Radiation enhanced diffusion in UO2 and (U,Pu)O2

Abstract

The radiation enhanced diffusion (coefficient D*) of U-233 and Pu-238 in UO₂ and (U, Pu)O₂ with 2.5 and 15% Pu was measured during fission in a nuclear reactor. Normal diffusion sandwiches with a thin tracer layer were used. A radio-frequency furnace allowed the temperatures to be varied between 130 and 1400°. Neutron fluxes (7 × 10¹² to 1.2 × 10¹⁴ n cm^?2 s^?1) and irradiation times (56 to 334 h) were also varied to cover ranges of fission rates [Fdot] between 7× 10¹¹ and 6.4 × 10¹³ f cm^?3 s^?1 and of doses F between 4.2 × 10¹⁷ and 3.1 × 10¹⁹ f cm³. Below ～1000°, D* was completely athermal and increased linearly with [Fdot]. It was described by D* = A[Fdot] with A = 1.2× 10^?29cm⁵. A possible temperature dependence was indicated between ～1000and 1200°. The results are explained in terms of thermal and pressure effects of fission spikes and are related with other studies of radiation damage as well as with technologically interesting processes occurring in UO₂ during irradiation.     

Effect of molybdenum on Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for rechargeable lithium ion batteries

Li₂Mn₄O₉ and molybdenum-doped Li₂Mn₄O₉ have been prepared by simple solid-state method. Molybdenum is used as a dopant since it is resistant to both corrosion and high-temperature creep deformation. The structural, morphological, and electrical performances of the samples have been analyzed. The material exhibits a cubic structure with the fd3m space group. Using EDAX, the chemical compositions of the samples have been identified. The dc electrical conductivity of the Mo-doped (LM2) sample is found to be increased to 7.44?×?10^?6 S cm^?1 at 393 K. The enhanced electrical property of the molybdenum-doped Li₂Mn₄O₉ reveals it as a feasible cathode material for rechargeable Li-ion batteries.     

Urea-assisted solvothermal synthesis of monodisperse multiporous hierarchical micro/nanostructured ZnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> microspheres and their lithium storage properties

High-quality monodisperse multiporous hierarchical micro/nanostructured ZnCo₂O₄ microspheres have been fabricated by calcinating the Zn_1/3Co_2/3CO₃ precursor prepared by urea-assisted solvothermal method. The as-prepared products are characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), and Brunauer-Emmett-Teller (BET) measurement to study the crystal phase and morphology. When tested as anode material for lithium ion batteries, the multiporous ZnCo₂O₄ microspheres exhibit an initial discharge capacity of 1,369 mAh g^?1 (3,244.5 F cm^?3) and retain stable capacity of 800 mAh g^?1 (1,896 F cm^?3) after 30 cycles. It should be noted that the good electrochemical performances can be attributed to the porous structure composed of interconnected nanoscale particles, which can promote electrolyte diffusion and reduce volume change during discharge/charge processes. More importantly, this ZnCo₂O₄ 3D hierarchical structures provide a large number of active surface position for Li⁺ diffusion, which may contribute to the improved electrochemical performance towards lithium storage.