2,3-Dihydroxypyridine Loaded Amberlite XAD-2 (AXAD-2-DHP): Preparation, Sorption–Desorption Equilibria with Metal Ions, and Applications in Quantitative Metal Ion Enrichment from Water, Milk and Vitamin Samples

2,3-Dihydroxypyridine loaded (via –N=N–linker) Amberlite XAD-2 (AXAD-2-DHP) was prepared and characterized by elemental analyses, TGA and FT-IR spectra. It (1g packed in a column of 1cm diameter; surface area 135.5m²g^–1) was found to be an effective solid phase sorbent for enriching Zn²⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺, Cu²⁺, Fe³⁺ and Co²⁺ at pH 3.5 to 7.0 using flow rates between 1.0–5.0mLmin^–1. For desorption (recovery 97.0–99.8%) of the metal ions, 8 to 10mL of 2.0molL^–1 HCl or 1.5molL^–1 HNO₃ at a flow rate of between 2.0 and 4.0mLmin^–1 were found most suitable. The t_1/2 (time for 50% sorption) is between 2 and 10min when a 50mL solution (containing a total amount of metal of 2mg) was equilibrated with 0.5g of resin. Sorption of all metal ions except Pb²⁺ follows the Langmuir model, whereas for Pb the data fits with the Freundlich model. The sorption capacity is between 60.7 (for Cd) and 406.7 (for Cu) µmolg^–1. The resin can withstand an acid concentration of 6molL^–1 and can be reused for thirty cycles of sorption–desorption. The preconcentration factor varies between 100 and 300. For Cd, Ni and Cu the sorption capacity of 2,3-dihydroxypyridine loaded cellulose is lower than that of the present resin. The tolerance limits of electrolytes, humic acid, complexing agents, Ca²⁺ and Mg²⁺ in the enrichment of all metal ions are reported. The limits of detection are 3.88, 5.37, 8.72, 13.88, 4.71, 1.24, 0.59 and 0.30µgL^–1 for Zn²⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺, Cu²⁺, Fe³⁺ and Co²⁺, respectively. The calibration curves for flame AAS determination were linear in the ranges 0.018–1.0, 0.067–5.0, 0.2–5.0, 0.9–20, 0.028–2.0, 0.077–5.0, 0.19–10 and 0.1–3.5µgmL^–1, respectively. All the eight metal ions in river and synthetic water samples, Co in vitamin tablets and Zn in milk samples have been quantitatively enriched with Amberlite XAD-2-DHP and determined by flame atomic absorption spectrometry.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Adsorptive Catalytic Voltammetry of Physcion in the Presence of Dissolved Oxygen at a Carbon Paste Electrode

A novel electroanalytical method for the determination of physcion is described for the first time. Physcion yields an adsorption catalytic voltammetric peak at –0.74V (vs. SCE) in 0.4molL^–1 NH₄Cl–NH₃·H₂O buffer solution (pH 10.5) at a carbon paste electrode (CPE). The experimental results indicated that physcion is efficiently accumulated at a CPE by adsorption. In the subsequent potential scan, physcion was reduced to a homologous anthrahydroquinone compound. The compound was then immediately oxidized to physcion by the dissolved oxygen in the solution, and then physcion was again reduced at the CPE. As a result, a cyclic catalytic reaction was established. The second-order derivative peak current is proportional to the physcion concentration in the ranges of 2.0×10^–104.0×10^–9molL^–1 (accumulation 90s) and 4.0×10^–92.0×10^–8molL^–1 (accumulation 60s). The limit of detection is 8×10^–11molL^–1 (S/N=3) for a 120s accumulation time. The method was applied to the direct determination of physcion in the medicinal plant polygonum multiflorum Thumb with satisfactory results.     

Simple and Sensitive Assay for Nucleic Acids Using their Quenching Effect on the Chemiluminescence Reaction Between Luminol and Hydrogen Peroxide with Manganese-Tetrasulfonatophthalocyanine as a New Catalyst

The manganese-tetrasulfonatophthalo-cyanine (MnTSPc) catalyzed luminol-hydrogen peroxide chemiluminescence (CL) system can be quenched in the presence of nucleic acids. A new and highly sensitive CL quenching method for determining nucleic acids in aqueous solutions has been developed. Under optimum conditions, linear relationships were found between the quenched intensity of CL and the concentration of nucleic acids in the range 0.10–2.0µgmL^–1 for calf thymus DNA and 0–1.6µgmL^–1 for fish sperm DNA. The limits of detection were 14.8ngmL^–1 for calf thymus DNA and 21.7ngmL^–1 for fish sperm DNA. The relative standard deviation (RSD) of nine replicate measurements is 1.4% for 1.0µgmL^–1 calf thymus DNA. The method was applied to the analysis of nucleic acids in synthetic samples and the results are satisfactory.Received December 2, 2002; accepted June 2, 2003 published online September 1, 2003     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Solid-Phase Extraction and Spectrophotometric Determination of Trace Amounts of Mercury in Natural Samples

A sensitive and selective solid phase spectrophotometric method for the determination of trace amounts of inorganic mercury is described. Hg²⁺ was sorbed on a silica gel-packed column as an Hg²⁺–N,N-bis(2-mercaptophenyl)ethanediamide (H₂L) complex. The Hg²⁺ complex was eluted from the column using 7mL of acetone. Various parameters including pH, column flow rate, and ligand concentration were optimized. The complex was found to obey Beers law from 2.3 to 73.7µgmL^–1 within the optimum range when the preconcentration factor was two. The effective molar absorption coefficient at 523nm was 1.17×10³Lmol^–1cm^–1 at 523nm. The concentration limits in Beers law dropped from 0.09 to 2.95µgmL^–1 within the optimum range when the preconcentration factor was 50. The relative standard deviation at a concentration level of 5µgmL^–1 Hg²⁺ (9 repetitive determinations) was 1.6%. The detection limits are 0.34µgmL^–1 and 0.015µgmL^–1 when the preconcentration factors are 2 and 50, respectively. The method has been used for routine determination of trace levels of Hg²⁺ in natural waters. The potential application of this method for the removal of Hg²⁺ from natural samples (sea water and lake water) spiked with 100ngmL^–1 of Hg²⁺ was studied. In order to validate the proposed method, LGC 6156 (harbour sediment – extractable metals) was analysed by this method. The results proved that excellent extraction of Hg²⁺ from both natural water samples was obtained by solid phase extraction using N,N-bis(2-mercaptophenyl) ethanediamide.     

Polarographic Determination of Lovastatin in the Presence of H2O2 in Pharmaceuticals, Human Urine and Serum

The polarographic reduction and catalytic behavior of lovastatin are studied by polarography and cyclic voltammetry. The reduction wave of lovastatin appears at ca. –1.49V (vs. SCE) in 0.16molL^–1 Na₂B₄O₇–KH₂PO₄ (pH=7.4) supporting electrolyte containing 20% ethanol. It is ascribed to a 2e^–, 2H⁺ addition to the carbonyl group on lactone ring. If H₂O₂ is present, the reduction wave is catalyzed to produce a polarographic catalytic wave. Based on the catalytic wave, a novel method for the determination of lovastatin is proposed. A rectilinear calibration curve of the catalytic wave was obtained for lovastatin concentration in the range 1.5×10^–8 to 1.0×10^–6molL^–1. The peak current of the catalytic wave is ca. 12 times higher than that of the corresponding reduction wave. The detection limit is 8.0×10^–9molL^–1. The proposed method is simpler, faster and more sensitive than the known methods for lovastatin analysis, and can be applied to the direct determination of lovastatin in pharmaceuticals, urine and serum without preliminary separation.     

Structural studies and diffusion measurements of water-swollen cellophane by NMR imaging

NMR imaging and spatially resolved diffusometry have been used to study the distribution of water within swollen cellophane and measure its diffusion coefficient. Water concentration and diffusion coefficient were found to be essentially constant across most of the film thickness. However, significantly slower diffusion was indicated for water near the film surface (D=0.5×10^–9m²s^–1) compared with water in the centre of the film (D=0.88×10^–9m²s^–1). This was also reflected in lower T ₂ values at the edge of the film indicating water with more restricted motion. These observations were interpreted in terms of dense surface regions of cellulose (skin) over a more porous interior (core).     

Electrochemical Behavior of Epinephrine at a Penicillamine Self-Assembled Gold Electrode,and its Analytical Application

The fabrication and electrochemical characteristics of a penicillamine (PCA) self-assembled monolayer modified gold electrode were investigated. The self-assembled electrode shows obvious electrocatalytic activity for the oxidation of epinephrine (EP). In phosphate buffer (pH 7.73), a sensitive oxidation peak was observed at 0.190V with the PCA modified Au electrode. The peak current is proportional to the concentration of EP in the range of 2.0×10^–56.0×10^–4molL^–1 and 5.0×10^–6 2.0×10^–4molL^–1 for cyclic voltammetry (CV) and differential pulse voltammetry (DPV) with the detection limits of 1.8×10^–7 and 1.3×10^–7molL^–1, respectively. The possible reaction mechanism is also discussed. The PCA self-assembled monolayer modified gold electrode is highly stable and can be applied to the determination of EP in practical injection samples. Application is simple, rapid and produces accurate results.     

Determination of Trace Proteins by Rayleigh Light Scattering Technique with Indophenol Blue

The interaction of indophenol blue (IPB) with proteins in aqueous solution has been studied by optical absorption and Rayleigh light scattering (RLS) spectroscopy. At pH 3.8, the weak RLS of IPB is enhanced by proteins. Based on this phenomenon, a novel method for the determination of proteins at nanogram levels using the RLS technique is developed. The method is simple, practical and sensitive. The linear range is 0.25–20.9µgmL^–1 for BSA, and 0.25–17.6µgmL^–1 for HSA. The detection limits (S/N=3) are 23ngmL^–1 for BSA and 22ngmL^–1 for HAS. The results for the determination of proteins in human serum samples are very close to those obtained by an established clinical method. There is very little interference from amino acids, metal ions or other coexisting compounds.     

Kinetics of formation,dissociation and equilibrium constants of pentacyanoaquoruthenate(II) with heterocycles

The kinetics of formation and dissociation reactions of [Ru(CN)₅L]^3– with a series of heterocyclic ligands were studied in aqueous media. In this presence of an excess of heterocycle, the observed second order rate constants were calculated from the k_obs versus [ligand] plot at =0.100m NaClO₄. Activation parameters for the formation reactions (H=28±7kJmol^–1 and S=140±35JK^–1mol^–1) are comparable for all systems, indicating a common mechanism. The kinetics of exchange of coordinated heterocycles for 1,3,5-triazine yielded a rate saturation typical of a limiting dissociative mechanism. Activation parameters of the limiting first order specific rate of dissociation reactions were H=85±7kJmol^–1 and S=18±4JK^–1mol^–1. Equilibrium constants were calculated from the second order rates of formation and pseudo-first order rates of dissociation reaction.     

Selective Kinetic Determination of Cu2+ with Tetraazamacrocyclic Bis(Methylphosphonate) Ligand (Dipon)

A new macrocyclic ligand, 1,4,8,11-tetraazacyclotetradecane-1,8-bis(methylphosphonic acid) (refered to as dipon) exhibits high thermodynamic and kinetic selectivity for Cu²⁺ compared to other transition metal ions. The initial-rate method (=310nm, pH=3.75, c_L4.6×10^–3molL^–1) was chosen as an optimal experimental approach in order to achieve maximum sensitivity of determination. The dynamic range of the method is (5–200)×10^–6molL^–1, and the detection limit is 2.5×10^–6molL^–1. A standard addition procedure was applied to the kinetic determination of Cu²⁺ to eliminate the effect of interfering ions (e.g. Zn²⁺, Ca²⁺, Mg²⁺, Cd²⁺, Pb²⁺, Mn²⁺, Co²⁺, Ni²⁺, HCO^–₃, Cl^–, SO₄^2–, etc.). The method was tested on artificial and real samples (alloys, pure and spiked mineral water) and gave satisfactory results which are in agreement with the values for some certified materials. The advantage of the proposed method is rapidity, simplicity and robustness in the presence of other metal ions.     

Determination of Iron in Tap and Waste Water Using Liquid–Liquid Extraction in a Flow-Injection System

A flow-injection procedure for the determination of iron(III) in water is described. The procedure is based on the formation of an ion pair between the tetraphenylarsonium (Ph₄As⁺) (TPA) or tetrabutylammonium (But₄N⁺) (TBA) cations and the tetrathiocyanatoferrate(III) complex (TTF). This ion pair is extracted with chloroform, and the absorbance of the organic phase is measured at 503nm (for Ph₄As⁺) or 475nm (for But₄N⁺). Iron concentrations higher than 0.9×10^–6molL^–1 (50µgL^–1) can be detected in the first case, with a relative standard deviation of 1.9% (n=12), a linear application rangeof between 1.34 and 54.0×10^–6molL^–1 (75–3015µgL^–1), and a sampling frequency of 30h^–1. For the ion pair with But₄N⁺, the detection limit is 0.52×10^–6molL^–1 (29µgL^–1), with a relative standard deviation of 1.6% and a linear application range between 0.73 and 54.0×10^–6molL^–1. Under the proposed working conditions, only Pd(IV), Cu(II) and Bi(III) interfere. With the application of the merging zones technique, considerable amounts of organic reagent can be saved. The TBA method was applied to the analysis of iron(III) in tap and industrial waste waters.     

Electrochemical Determination of Ascorbic Acid at γ-MnO<Subscript>2</Subscript> Modified Carbon Black Microelectrodes

A carbon black microelectrode modified by -MnO₂ has been prepared. The electrocatalytical oxidation of ascorbic acid (AA) at this microelectrode was investigated. The 2nd-order linear scan voltammograms of AA are recorded from –0.5 to 0.5V (vs. SCE). The relationship between the oxidation peak current of AA and its concentration in the range of 1.0×10^–64.0×10^–3molL^–1 is linear. The detection limit (3) was found to be 6.0×10^–7molL^–1. Also, the determination of AA in samples is evaluated, and the results are satisfactory.     

Statistical Evaluation of Cu,Mn and Zn Determinations in Biological Samples by Radiofrequency Capacitively Coupled Plasma Atomic Emission Spectrometry Using the Bland and Altman Test

This paper presents a statistical comparison of Cu, Mn and Zn determinations in biological samples by low power radiofrequency capacitively coupled Ar plasma (275W; 27.12MHz; 0.4Lmin^–1 flow rate) atomic emission spectrometry and flame atomic absorption spectrometry using statistical analysis according to the Bland and Altman test and linear regression. For a content (µgg^–1 dry mass) of 5-43 Cu, 10-15800 Mn and 8-1100 Zn in fish fillet and freshwater molluscs, there was no significant bias in r.f.CCP-AES for a 95% confidence level. Certified reference materials were analysed by r.f.CCP-AES, and a good agreement between analysis results and certified values was obtained. Matrix effects of Ca and Na and their influence on the detection limits of Cu, Mn and Zn are presented for both methods. As compared to FAAS, r.f.CCP-AES is more prone to interferences and, consequently, the detection limits for Cu, Mn and Zn in biological samples (2; 2 and 3µgg^–1 dry mass) are higher than those in FAAS. In spite of these problems, r.f.CCP-AES is capable of accurate and precise analyses of biological samples.     

Application of L-Cysteine-Capped ZnS Nanoparticles in the Determination of Nucleic Acids Using the Resonance Light Scattering Method

Nanometer-sized L-cysteine-capped ZnS particles were synthesized by a colloidal aqueous method. The functionalized nanoparticles are water-soluble and suitable for biological applications. In Tris-HCl buffer solution, nucleic acids combine with cysteine-capped nano-ZnS particles by intermolecular forces to form larger nanoparticles. There are two resonance light scattering peaks at 304.5nm and 373.8nm, respectively. The enhanced RLS is related to the concentration of nucleic acids in the range of 0.04 to 1.2µgmL^–1 for calf thymus DNA and 0.2 to 1.0µgmL^–1 for fish sperm DNA. The detection limits (3) are 19ngmL^–1 for calf thymus DNA and 23ngmL^–1 for fish sperm DNA, respectively. Four synthetic samples were analyzed satisfactorily.     

The Fluorescent Reaction Between Quinaldine Red and Nucleic Acids and its Application to Fluorescent Assay of DNA and RNA

The reaction between quinaldine red (QR) and nucleic acids was studied. The free QR alone has no fluorescence in solution. However, it becomes fluorescent after binding to nucleic acids, giving maximum emission at 607nm with maximum excitation at 557nm. Maximum fluorescence intensity is produced in the pH range of 3.2–3.6. Based on the fluorescent reactions, a novel fluorometric method was developed for rapid determination of nucleic acids using QR as the fluorescent probe. Under optimal conditions, the calibration graphs were linear in the range of 0–30.0µgmL^–1 for CT DNA and 0–20.0µgmL^–1 for yeast RNA. The limits of detection were 38ngmL^–1 for CT DNA and 142ngmL^–1 for yeast RNA. Four synthetic samples were determined with satisfaction.Received December 20, 2002; accepted March 27, 2003 Published online August 8, 2003     

Indirect Determination of Sulfide by Cold Vapor Atomic Absorption Spectrometry

A method for the determination of sulfide based on its interference with the determination of Hg by cold vapor atomic absorption spectrometry is described. The decrease in mercury absorbance at 253.7nm is proportional to the concentration of sulfide over the range of 10–320ngmL^–1. The limit of detection was found to be 7ngmL^–1 and the relative standard deviation (R.S.D.) for the determination of different concentrations of sulfide was in the range of 1.8–2.2%. This method was applied to the determination of sulfide in whole human blood after gas-phase separation.     

Electrochemical Determination of 4-Nitrophenol Using a Single-Wall Carbon Nanotube Film-Coated Glassy Carbon Electrode

A single-wall carbon nanotubes (SWNT) film coated glassy carbon electrode (GCE) was fabricated for the direct determination of 4-nitrophenol (4-NP). The electrochemical behaviors of 4-NP at the SWNT-film coated GCE were examined. In 0.1M phosphate buffer with a pH of 5.0, 4-NP yields a very sensitive and well-defined reduction peak at the SWNT-modified GCE. It is found that the SWNT film exhibits obvious electrocatalytic activity towards the reduction of 4-NP since it not only increases the reduction peak current but also lowers the reduction overpotential. Based on this, an electrochemical method was proposed for the direct determination of 4-NP. The reduction peak current varies linearly with the concentration of 4-NP ranging from 1×10^–8 to 5×10^–6M, and the detection limit is 2.5×10^–9M after 3min of open-circuit accumulation. The relative standard deviation at 2×10^–7M 4-NP was about 6% (n=10), suggesting excellent reproducibility. This new method was successfully employed to determine 4-NP in several lake water samples.     

Kinetic Determination of Microquantities of Rutin by Perturbation of the Bray-Liebhafsky Oscillatory Reaction in an Open System

A kinetic method is described for the microquantitative (microconcentration/microvolume) determination of rutin based on potentiometric monitoring of the concentration perturbations of the Bray-Liebhafsky (BL) oscillatory reaction being in a non-equilibrium stationary state close to a bifurcation point. The experiments are carried out in an open reactor. The response of the matrix system to perturbations by different concentrations of rutin ethanolic solutions is followed by a Pt-electrode. In the concentration range between 7.8×10^–8moldm^–3 and 9.1×10^–6mol dm^–3, we found a linear dependence of the maximal potential shift, E_m, on the logarithm of the rutin concentrations. The unknown concentrations can be determined from the calibration curve up to an accuracy of ±5%. The detection limit is 3.6×10^–8mol dm^–3. The amount of required sample can be as small as 10µL.