Optimizing adsorptive removal of malachite green and methyl orange dyes from simulated wastewater by Mn‐doped CuO‐Nanoparticles loaded on activated carbon using CCD‐RSM: Mechanism,regeneration, isotherm,kinetic, and thermodynamic studies

In the present work, Mn‐doped CuO‐NPs‐AC was prepared by a simple method, characterized using various techniques such as FESEM, EDX, XRD, PSD, and pH_pzc and finally used for the adsorption of malachite green (MG) and methyl orange (MO) in a number of single and binary solutions. A series of adsorption experiments were conducted to investigate and optimize the influence of various factors (such as different pH, concentration of MG and MO, adsorbent mass, and sonication time) on the simultaneous adsorption of MG and MO using response surface methodology. Under optimal conditions of pH 10, adsorbent dose of 0.02 g, MG concentration of 30 mg L^?1, MO concentration of 30 mg L^?1, and sonication time of 4.5 min at room temperature, the maximum predicted adsorption was observed to be 100.0%, for both MG and MO, showing that there is a favorable harmony between the experimental data and model predictions. The adsorption isotherm of MO and MG by Mn‐doped CuO‐NPs‐AC could be well clarified by the Langmuir model with maximum adsorption capacity of 320.69 mg g^?1 and 290.11 mg g^?1 in the single solution and 233.02 mg g^?1 and 205.53 mg g^?1 in the binary solution by 0.005 g of adsorbent mass for MG and MO, respectively. Kinetic studies also revealed that both MG and MO adsorption were better defined by the pseudo‐second order model for both solutions. In addition, the thermodynamic constant studies disclosed that the adsorption of MG and MO was likely to be influenced by a physisorption mechanism. Eventually, the reusability of the Mn‐doped CuO‐NPs‐AC after six times showed a reduction in the adsorption percentage of MG and MO.     

Cellulose from Tamarix aphylla’s stem via acetocell for cadmium adsorption

This study emphasized the efficiency of unconventional delignification treatment “Acetocell” as a basic pretreatment to isolate cellulose fiber from Tamarix aphylla’s stem. Chemical proprieties of obtained cellulose were determined and its efficiency for cadmium ions adsorption was evaluated subsequently. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction analysis, thermogravimetric analysis (TGA), Scanning Electron Microscopy (SEM), fluorescence microscope and Morfi were used to analyze the thermochemical and morphological characteristics of the fibers before and after treatment. Cellulose was used as a biosorbent to remove cadmium ions from polluted water. The effects of many parameters on the efficiency removal of cadmium were investigated; the amount of cellulose, the contact time, pH and the initial concentration of cadmium ions. The optimum conditions were 45 mg of adsorbent, 45 mg L^?1, 1200 min and pH 8 which provide best adsorption capacity equal to 44.21 mg g^?1. The energy value E = 6.65 kJ mol^?l which confirm the physical interaction between cellulose-cadmium ions.Then Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models were followed for modeling adsorption. Langmuir isotherm and the pseudo-second order model seems the most suitable which describe better the adsorption of cadmium ions with best R² values which equal to 0.9937 and 0.9979, respectively.     

Highly efficient elimination of thorium(IV) from aqueous solution using poly(cyclotriphosphazene-co-melamine) microspheres

Highly crosslinked organic–inorganic hybrid polymer poly(cyclotriphosphazene-co-melamine) microspheres (PZM) were synthesized by a simple method. The microspheres was characterized by FTIR, SEM and EDX. It was applied to eliminate thorium(IV) from aqueous solution under various conditions, i.e., pH, initial concentration, dosage and contact time. The experimental data were well-imitated via the pseudo-second-order kinetic model and its adsorption processes comply with the Langmuir isotherm model. Adsorption thermodynamic studies demonstrated that the adsorption process, in essence, was spontaneous and endothermic. Furthermore, the maximum experimental adsorption capacity was 98.6 mg g^?1 for initial thorium(IV) concentration 50 mg L^?1. When pH?=?0.0, the thorium(IV) removal efficiency reached at 76.9%, which indicates that the adsorbent can also was used in a peracid environment. Adsorption behavior of thorium(IV) onto the microspheres were weakly affected via temperature, implying that adsorption would be done at room temperature.

     

Analysis of the role of various biochar in the remediation of heavy metals in contaminated water and its kinetics study

Biochar prepared from agricultural wastes has gained great attention as a cost-effective treatment for metal-contaminated water. In this study, the effectiveness of corn cob and sugarcane bagasse-derived biochar for metals (Pb, Ni, and Cu) removal from an aqueous medium was examined following their physical, chemical, and structural characterization. Batch sorption experiments were carried out by employing the Langmuir and Freundlich equations. The results indicated that separation factor (R_L) values lay in the range of 0 and 1 representing the productive adsorption. The optimum dosage for metal adsorption can be recommended as 30 g L^?1. The optimum adsorption conditions were found at 6.5 and 5.5 pH, 1.5 g adsorbent dose, and at 180 min equilibrium time, for both corn cob and sugarcane bagasse biochars. At pH 6.5, adsorption capacities of Pb, Ni, and Cu were found maximum i.e., 11.34, 15.71, and 11.96 mg kg^?1 for corn cob and 8.96, 15.46, and 12 mg kg^?1, for sugarcane bagasse biochars, respectively. The metal adsorption kinetics was analyzed via four different types of the pseudo-second-order kinetic model. Moreover, the corn cob biochar showed a more pronounced activity in the removal of metals compared to sugarcane bagasse biochar. Hence, it was concluded that corncob and sugarcane bagasse-derived biochars could be utilized as economical bio-adsorbents for the heavy metals removal from wastewater.     

Nitrate removal from aqueous solution using watermelon rind derived biochar-supported ZrO2 nanomaterial: Synthesis,characterization, and mechanism

Recently, biochar has attracted tremendous research interest for environmental applications. In this study, biochar-derived watermelon rind (WM) was produced via optimal pyrolysis at 500 °C for 2 h, and then improved the adsorption capacity by Zirconium oxide nanoparticles (ZrO₂ NPs). The WM@ZrO₂ was characterized using X-ray diffraction (XRD), Scanning electron microscopic - Energy-dispersive X-ray spectroscopy (SEM-EDS), and Fourier transform infrared (FTIR). The adsorptive capacities of synthesized ZrO₂ NPs were investigated for nitrate as a function of pH, adsorbent dosage, contact time, initial adsorbate concentration, and pyrolysis temperature in the batch experiment. The results showed that a Langmuir isotherm and a pseudo-second-order kinetics model were the best-fit for experimental nitrate data in its non-linear form as correlation coefficients (R²) were 0.985 and 0.998, respectively. The maximum adsorption capacity for the Langmuir isotherm model was 15.196 mg g^?1. The proposed mechanism, including electrostatic attraction and ligand exchange, played a dominant role in nitrate adsorption. After testing with the real domestic wastewater, the removal of nitrate for WM@ZrO₂ was achieved at 78 %, which was equivalent to the adsorption capacity of 8.1 mg g^?1 of adsorbent. Overall, the WM@ZrO₂ is proposed as a promising, effective, and environmentally friendly adsorbent in removing nitrate from an aqueous solution.     

Development of magnetic dispersive microsolid-phase extraction using lanthanum phosphate nanoparticles doped on magnetic graphene oxide as a highly selective adsorbent for pesticide residues analysis in water and fruit samples

Magnetic graphene oxide/lanthanum phosphate nanocomposite (MGO@LaP) was synthesized and used as an efficient adsorbent for magnetic dispersive microsolid-phase extraction (MD-µ-SPE) of pesticides before gas chromatography–electron capture detector (GC–ECD) analysis. The adsorbent was thoroughly characterized with scanning electron microscopy, vibrating sample magnetometer, energy-dispersive X-ray spectroscopy, and Fourier transform infrared spectroscopy. Optimized extraction conditions were investigated concerning extraction time, adsorbent amount, sample pH, and salt amount as well as desorption conditions (type and volume of desorption solvent and desorption time). Under the optimal conditions, the method demonstrated good linearity (3–1500 µg L^?1) with satisfactory determination coefficients of >?0.997 and low detection limits for both chlorpyrifos (0.67 µg L^?1) and hexaconazole (0.89 µg L^?1). Finally, the method showed high analyte relative recoveries in the range of 78–120% for the determination of the selected pesticides in water and fruit juice samples.

     

Glutaraldehyde cross-linked epoxyaminated chitosan as an adsorbent for the removal and recovery of copper(II) from aqueous media

A novel glutaraldehyde cross-linked epoxyaminated chitosan (GA-C-ENCS) prepared through chemical modification was used as an adsorbent for the removal and recovery of Cu(II) from aqueous media. The adsorbent was characterized by FTIR, SEM-EDS, ESR, TG/DTG, BET-surface area and potentiometric titration. The Cu(II) adsorption process, which was pH dependent showed maximum removal at pH 6.0. Adsorption equilibrium was achieved within 3 h. The adsorption of Cu(II) followed a reversible-first-order kinetics. The equilibrium data were evaluated using the Langmuir, Freundlich and Dubinin–Radushkevich isotherm models. The best interpretation for the equilibrium data was given by the Dubinin–Radushkevich isotherm. The adsorption capacity of the adsorbent increased from 3.11 to 3.71 mmol g⁻¹ when the temperature was increased from 20 to 50 °C. The complete removal of 20.7 mg L⁻¹ Cu(II) from electroplating industry wastewater was achieved by 0.4 g L⁻¹ GA-C-ENCS. Regeneration experiments were tried for four cycles and the results indicate a capacity loss of <7.0%.     

Solid phase extraction of hexavalent chromium by Mannich base polymer wrapped flower-like layered double hydroxide

In the present work, synthesis of polymer wrapped flower-like MgAl layered double hydroxide was done through condensation of 1,4 phenylenediamine and resorcinol by p-formaldehyde. The nanocomposite was characterised with X-ray diffraction analysis, fourier transform infrared spectroscopy, thermogravimetric analysis and field emission scanning electron microscopy techniques and employed for effective adsorption of Cr(VI) from aqueous solution prior to flame atomic absorption spectrometer determination. Optimum level of effective parameters (pH, reaction time and adsorbent dosage) and their interaction was determined by response surface methodology. To investigate applicability of method for trace heavy metal adsorption, the method was employed for preconcentration of Cr(VI) in water samples. At the optimum conditions, pH = 4.5, shaking time of 15 min and adsorbent dosage of 20 mg, analytical performance of the method was evaluated and results showed that calibration curve is linear in the concentration range of 2–100 μg L^?1. Moreover, limit of detection was 0.22 µg L^?1 and relative standard deviation of six replicate experiments at initial concentration of 0.1 mg L^?1 was 3.3%. Isotherm study showed that Freundlich model can better describe adsorption behaviour as well as the sorbent showed the adsorption capacity of 62.5 mg g^?1. Moreover, thermodynamic study revealed that chromate adsorption was spontaneous and followed the endothermic path. Regeneration of sorbent was performed using 1.0 mol L^?1 of NaOH solution. The sorbent was employed for Cr(VI) determination from food additives and seawater samples.     

Immersion enthalpy and the constants of Langmuir model in the 3-chloro phenol adsorption on activated carbon

The adsorption process of 3-chloro phenol from aqueous solution on a activated carbon prepared from African palm stone and which presents a specific surface area of 685 m² g⁻¹, a greater quantity of total acid groups and a pH_PZC of 6.8 is studied. The adsorption isotherms are determined at pH values of 3, 5, 7, 9 and 11. The adsorption isotherms are fitted to the Langmuir model and the values of the maximum quantity adsorbed that are between 96.2 and 46.4 mg g⁻¹ are obtained along with the constant K_L with values between 0.422 and 0.965 L mg⁻¹. The maximum quantity adsorbed diminishes with the pH and the maximum value for this is a pH of 5. The immersion enthalpies of the activated carbon in a 3-chloro phenol solution of constant concentration, of 100 mg L⁻¹, are determined for the different pH levels, with results between 37.6 and 21.2 J g⁻¹. Immersion enthalpies of the activated carbon in function of 3-chloro phenol solution concentration are determined to pH 5, of maximum adsorption, with values between 28.3 and 38.4 J g⁻¹, and by means of linearization, the maximum immersion enthalpy is calculated, with a value of 41.67 J g⁻¹. With the results of the immersion enthalpy, maximum quantity adsorbed and the constant K_L, establish relations that describe the adsorption process of 3-chloro phenol from aqueous solution on activated carbon.     

Application of Photo-Fenton,Electro-Fenton,and Photo-Electro-Fenton processes for the treatment of DMSO and DMAC wastewaters

Biological treatment, due to the formation of hazardous chemicals to remove organic compounds such as dimethyl sulfoxide (DMSO) and N, N-dimethylacetamide (DMAC), has limited potential. Advanced oxidation processes (AOPs) are regarded as a viable alternative for treating molecules containing carbon-hydrogen bonds that cannot be broken down by traditional physico-chemical methods. In this investigation, various AOPs such as Photo-Fenton, Electro-Fenton, and Photo-Electro-Fenton processes were studied to treat wastewaters containing DMSO and DMAC. The effects of the operating parameters, including various initial concentrations of DMSO and DMAC, initial pH, reaction time, different concentrations of Fenton’s reagent, power of UV lamp, different concentrations of electrolytes, the distance between electrodes and current intensity, were investigated. The findings of the experiments revealed that a pH of 3 and a reaction time of 120 min were optimal. At 2000 mg L^?1 of DMSO, maximum degradation and the final concentration of TOC were 98.64 % and 256.8 mg L^?1, respectively, by the Electro-Fenton process under the optimal conditions. The Electro-Fenton process was successful in determining the maximum degradation of DMAC (96.31 %) and the final TOC concentration (10.03 mg L^?1) at 250 mg L^?1 of DMAC under optimal conditions. Finally, it can be concluded that the Electro-Fenton process was the best process for the efficient removal of DMSO and DMAC. The second step of the kinetic model follows a pseudo-first-order reaction for 250 and 500 mg L^?1 of pollutants and obeyed a pseudo-second-order kinetic model for concentrations of 1000, 2000 mg L^?1.     

Structural and adsorption behaviour of ZnO/aminated SWCNT-COOH for malachite green removal: face-centred central composite design

In this study, an effective adsorbent was synthesized to remove malachite green (MG), which is one of the toxic dyes. Firstly, single walled carbon nanotube with carboxylated acid (SWCNT-COOH) was functionalized with diethylenetriamine and a new nanocomposite was obtained using nano zinc oxide (ZnO) powder. The effects of pH (3–7), the amount of adsorbent (5–15 mg) and the initial concentration (10–50 mg L^–1) of the solution on the adsorption uptake were investigated. The optimal parameters that maximize the adsorption uptake according to the specified working range are found to be 4.63 for pH, 49.94 mg L^–1 for initial concentration, 5.25 mg for the adsorbent dose, and the maximum adsorption capacity has been found as 52.26 mg g^–1. The excellent fitting of the pseudo-second kinetic model with (R² = 0.9912) was fitted the experimental data. The Freundlich isotherm model gave a clue about the type of adsorption. Furthermore, thermodynamic results showed that adsorption process was endothermic.     

Synthesis of CuS nanoparticles loaded on activated carbon composite for ultrasound‐assisted adsorption removal of dye pollutants: Process optimization using CCD‐RSM,equilibrium and kinetic studies

In this study, the CuS nanoparticles loaded on activated carbon (CuS‐NPs‐AC) composite was synthesized and then, characterized by XRD and FE‐SEM analyses. The prepared composite was used as a potential adsorbent for the simultaneous ultrasound‐assisted removal of Indigo Carmine (IC) and Safranin‐O (SO). The CuS‐NPs‐AC dose (0.01‐0.03 g), sonication time (1‐5 min), initial SO concentration (5‐15 mg L^‐1) and initial IC concentration (5‐15 mg L^‐1) as expectable effective parameters were studied by central composite design (CCD) under response surface methodology (RSM) to obtain an useful knowledge about the effect of simultaneous interaction between IC and SO on their removal percentage. The optimum SO and IC removal percentages were determined to be 98.24 and 97.15% at pH = 6, 0.03 g of the CuS‐NPs‐AC, 3 min sonication time, 12 and 10 mg L^‐1 of IC and SO. The values of coefficient of determination (R²) for SO and IC were 0.9608 and 0.9796, respectively, indicating the favorable fitness of the experimental data to the second order polynomial regression model. The isotherm data were well correlated with Freundlich model. The maximum monolayer adsorption capacities of 87.5 and 69.90 mg g^‐1 at room temperature for IC and SO in the investigated binary system expressed the high efficiency of the novel adsorbent for water cleanup within a short time. The investigation of correlation between time and rate of adsorption revealed that IC and SO adsorption onto the CuS‐NPs‐AC followed pseudo‐second‐order and intra‐particle diffusion simultaneously.     

Preparation of ferric nitrate–graphene nanocomposite and its adsorption of arsenic(V) from simulated arsenic‐containing wastewater

Ferric nitrate–graphene (FG) nanocomposites synthesized via the equivalent‐volume impregnation method were used for the removal of As(V) species from simulated arsenic‐containing wastewater. Effects of various factors were assessed, such as the reaction temperature, solution pH, adsorbent dosage, and reaction time. The results indicated that the As(V) removal efficiency was as high as 99%, and the concentration of arsenic‐containing wastewater after FG treatment was as low as 9.4 μg L^–1 as a result of the optimal absorption capacity and maximum specific surface area (171.766 m²/g) of this material. The equilibrium adsorption capacity of FG for As(V) was achieved in approximately 20 min, and the maximum adsorption capacity was calculated to be 112.4 mg g^–1 by Langmuir adsorption isotherm, which was higher than that of other adsorbents such as manganese‐incorporated iron(III) oxide–graphene (14.42 mg g^–1). Moreover, the removal efficiency of As(V) can be maintained above 95% under acidic and alkaline conditions. Brunauer–Emmett–Teller analysis showed that the modified FG pore structure was regular. Based on the characterizations by X‐ray diffraction, X‐ray photoelectron spectroscopy, and Fourier transform infrared, the products on the surface of the used FG were Fe(OH)₃, FeAsO₄, and other compounds, and As(V) was mainly removed by the formation of insoluble compounds and coprecipitation.     

Three-dimensional graphene materials for UO22+ electrosorption

In this paper, three-dimensional graphene (3DG) electrode material was prepared by hydrothermal reduction using graphene oxide as precursor. Its morphology and structure were characterized by SEM, BET, XRD, Raman, FTIR and TG, and its electrochemical performance was also measured. The results showed that 3DG possessed hierarchical pore structure, large specific surface area, high specific capacitance and low impedance. Using 3DG as electrode material for electrosorption of UO₂²⁺, it showed that the saturated adsorption capacity can reach up to 113.80 mg g^?1 and the adsorption rate is 0.32 mg g^?1 min^?1 at a given optimal applied voltage of 1.8 V.

     

Preparation of carbon coated Fe3O4 nanoparticles for magnetic separation of uranium

Uranium(VI) was removed from aqueous solutions using carbon coated Fe₃O₄ nanoparticles (Fe₃O₄@C). Batch experiments were conducted to study the effects of initial pH, shaking time and temperature on uranium sorption efficiency. It was found that the maximum adsorption capacity of the Fe₃O₄@C toward uranium(VI) was ∼120.20 mg g⁻¹ when the initial uranium(VI) concentration was 100 mg L⁻¹, displaying a high efficiency for the removal of uranium(VI) ions. Kinetics of the uranium(VI) removal is found to follow pseudo-second-order rate equation. In addition, the uranium(VI)-loaded Fe₃O₄@C nanoparticles can be recovered easily from aqueous solution by magnetic separation and regenerated by acid treatment. Present study suggested that magnetic Fe₃O₄@C composite particles can be used as an effective and recyclable adsorbent for the removal of uranium(VI) from aqueous solutions.     

Bio-adsorption of dyes from aqueous solution by powdered excess sludge (PES): Kinetic,isotherm, and thermodynamic study

Over 30 million tons of excess sludge is discharged from rural municipal sewage plants annually in China and it is predicted that this figure will keep increasing. However, most of the excess sludge is dumped in landfills except for minor applications. In this study, based on low-cost and recycling waste, the excess sludge was used to adsorb organic dyes from aqueous solution after being directly dewatered. The powdered excess sludge (PES) presents selective adsorption property to cationic dyes. Statics batch adsorption experiments of malachite green (MG) on PES were performed to evaluate the effects of pH, adsorbent dosage, and initial MG concentration. Results revealed that the bio-adsorption equilibrium of MG on the PES can be quickly achieved at 30 min with maximum percentage adsorption of 84% at pH 7, initial dye concentration of 20 mg L^?1, and adsorbent dosage of 1.5 g L^?1. Moreover, the adsorption kinetics follows a pseudo-second-order pathway, and the equilibrium adsorption data could be described well by the Langmuir isotherm equation. Intra-particle diffusion is not the only rate-controlling step in the entire adsorption process. The adsorption process is endothermic, spontaneous, and random. PES can be used as a low-cost adsorbent for refractory cationic organic dye in effluent.     

Preparation and characterization of nanocomposite,silica aerogel,activated carbon and its adsorption properties for Cd (II) ions from aqueous solution

A novel composite adsorbent, silica aerogel activated carbon was synthesized by sol-gel process at ambient pressure drying method. The composite was characterized by Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Nitrogen adsorption/desorption isotherms (BET).In the present study, the mentioned adsorbent was used moderately for the removal of cadmium ions from aqueous solutions and was compared with two other adsorbents of cadmium, activated carbon and silica aerogel. The experiments of Cd adsorption by adsorbents were performed at different initial ion concentrations, pH of the solution, adsorption temperature, adsorbent dosage and contact time. Moreover, the optimum pH for the adsorption was found to be 6.0 with the corresponding adsorbent dosage level of 0.1 g at 60 °C temperature. Subsequently, the equilibrium was achieved for Cd with 120 min of contact time.Consequently, the results show that using this composite adsorbent could remove more than 60% of Cd under optimum experimental conditions. Langmuir and Freundlich isotherm model was applied to analyze the data, in which the adsorption equilibrium data were correlated well with the Freundlich isotherm model and the equilibrium adsorption capacity (q_e) was found to be 0.384 mg/g in the 3 mg/L solution of cadmium.     

Surface‐initiated atom transfer radical polymerization of a new rhodanine‐based monomer for rapid magnetic removal of Co(II) ions from aqueous solutions

The present study reports synthesis and characterization of a new acrylamide‐based monomer containing rhodanine moiety, N‐3‐amino‐thiazolidine‐4‐one‐acrylamide (ATA). Poly(ATA)‐grafted magnetite nanoparticles (poly(ATA)‐g‐MNPs) were prepared using surface‐initiated atom transfer radical polymerization of the monomer on Fe₃O₄ nanoparticles. The grafted nanoparticles were characterized by Fourier transform infrared analysis, scanning electron microscopy, X‐ray diffraction, and vibrating sample magnetometry. The amount of the grafted polymer was 209 mg g⁻¹, as calculated from thermogravimetric analysis experiment. The capability of poly(ATA)‐g‐MNPs to remove Co(II) cations was shown under optimal conditions of contact time, pH, adsorbent dosage, and initial Co(II) concentration. About 86% of the Co(II) cations were removed over 7 minutes. The adsorption kinetics obeyed the pseudo–second‐order kinetic equation, and the Langmuir isotherm model best described the adsorption isotherm with a maximum adsorption capacity of 3.62 mg g⁻¹. The thermodynamic investigation showed spontaneous nature of the adsorption process (ΔG = −2.90 kJ mol⁻¹ at 25°C ± 1°C). In addition, the poly(ATA)‐g‐MNPs were regenerated by simply washing with an aqueous 0.1M HCl solution. The study of the reusability of the prepared magnetic sorbent revealed that the sorbent can be reused without a significant decrease in the extraction efficiency and be recovered by 95.4% after 7 cycles. These findings suggest that the grafted nanoparticles are stable and reusable adsorbent and can be potentially applied to water treatment in efficient removal of Co(II) cations.     

Innovative separation and preconcentration technique of coagulating homogenous dispersive micro solid phase extraction exploiting graphene oxide nanosheets

A uniquely novel, fast, and facile technique is introduced for the first time in which a scant amount of graphene oxide (GO), without modification, has been utilized in dispersive mode of solid phase extraction (SPE) for an efficient yet simple separation. The proposed method of coagulating homogenous dispersive micro solid phase extraction (CHD-µSPE) is based on coagulation of homogeneous GO solution with the aid of polyetheneimine (PEI). CHD-µSPE use full adsorption capacity of GO because in this method was used GO solution obtained from synthesis process without drying step and stacking nanosheets. In optimized condition, 30 µL GO solution (7 mg mL⁻¹), obtained in synthesis process, was injected into 1.5 mL the sample solution followed by immediate injection of 53 µL PEI solution (1 mg mL⁻¹). After inserting PEI, GO sheets aggregate and can be readily separated by centrifugation. PEI not only cause aggregation of GO, but also form three-dimensional network of GO with easy handling in following separation steps. Lead, cadmium, and chromium were selected as model analytes and the effecting parameters including the amount of GO, concentration of PEI, sample pH, extraction time, and type of desorption solvent were investigated and optimized. The results indicate that the proposed CHD-µSPE method can be successfully applied GO in dispersive mode of SPE without effecting on good capability adsorption of GO. The novel method was applied in determination of lead, cadmium, and chromium in water, human saliva, and urine samples by electrothermal atomic absorption spectrometry. The detection limits are as low as 0.035, 0.005, and 0.012 µg L⁻¹ for Pb, Cd, and Cr respectively. The intra-day precisions (RSDs) were lower than 3.8%. CHD-µSPE method showed a good linear ranges of 0.24–15.6, 0.015–0.95 and 0.039–2.33 µg L⁻¹ for Pb, Cd and Cr respectively. Method performance was investigated by determination of mentioned metal ions in river water, human urine and saliva sample with good recoveries in range of 94.2–103.0%. The accuracy of the method was underpinned by correct analysis of a standard reference material (SRM: 2668 level I, Urine).     

Graphene oxide functionalized magnetic nanoparticles as adsorbents for removal of phthalate esters

We show that magnetic nanoparticles can be functionalized with graphene oxide (GO-MNPs) in two reaction steps, and that such nanoparticles can be used as adsorbents for the removal of phthalate esters (PAEs) from water samples. The GO-MNPs were characterized by scanning electron microscopy, transmission electron microscopy, Fourier-transform infrared spectroscopy, zeta potential, and vibrating sample magnetometer. The impacts of contact time, sample pH, ionic strength and sample volume on the adsorption process were investigated. The maximum adsorption capacity for diethyl phthalate was calculated to be 8.71 mg g^?1 according to the Langmuir adsorption isotherm. The adsorption efficiency was tested by removal of PAEs. More than 99 % of the total quantity of PAEs (0.12 mg L^?1) in 500 mL real water samples can be removed when GO-MNPs (275–330 mg) were used as an adsorbent. In addition, other species (estriol and fluorene) containing benzene rings were also almost completely removed with the PAEs using GO-MNPs, indicating that GO-MNPs are suitable for the removal of the species containing π-electron system through π-π interactions.