Changes in Porosity and Amounts of Adsorbed Water in Sol-Gel Derived Porous Silica Films with Heat Treatment

Porous silica films were obtained by a heat treatment of poly(ethyleneglycol)-containing gels for micro-patterning. Changes in porosity and the amount of adsorbed water with the heat treatment temperature in the silica films were evaluated from the refractive index of the films. The apparent refractive index of the silica films in an ambient atmosphere was much higher than the intrinsic refractive index of the film due to the large amount of adsorbed water in the films. The amount of adsorbed water in the films decreased with an increase in the heat treatment temperature and became almost zero after a heat treatment at 850°C. The decrease in the amount of adsorbed water in the films was caused by the decrease in silanol groups, which acted as the sites for water adsorption in the films. The drastic decreases in thickness and in porosity of the films at temperatures from 850 to 950°C occurred after the disappearance of silanol groups in the films. The densification of the films due to collapse of the pores at high temperatures should have resulted from the viscous flow of silica network.     

Thermogravimetry as a Reliable tool to Estimate the Density of Silanols on a Silica Gel Surface

A method was developed to estimate the density of the silanol groups attached to silica gel surfaces from thermogravimetric data. Depending on the mechanism of condensation of silanol groups during heating, after removing physically adsorbed water, the results obtained ranged from 4.3 to 6.7 OH nm^-2 for a series of silicas. The data are in good agreement with those obtained by other techniques. Thermogravimetry proved to be a reliable tool for this kind of study, with the great advantage of being a simple, quick and inexpensive method requiring only a few mg of the silica sample. This revised version was published online in July 2006 with corrections to the Cover Date.     

Adsorption of codeine on hydrophilic silica and silica surface modified by hydrophobic groups in the presence of electrolytes

The adsorption of codeine from aqueous solution onto colloidal silica and silica surface-modified with chemiadsorbed octadecyl dimethyl silane (ODDMS) or dimethyl silane (DMS) groups was studied in the presence of neutral electrolytes at different pH values. From codeine-hydrochloride solutions codeine cations are strongly bound to negatively charged silica surfaces. Inorganic salts (NaCl, NaNO₃) reduce the adsorption of the organic cation. On silica modified by ODDMS (10% of surface silanol groups are occupied), codeine cations are adsorbed to a higher extent at pH 6, while at pH 8 the adsorbed amounts are lower than on the bare silica surface. Neutral electrolytes reduce codeine adsorption on the ODDMS modified silica. On the hydrophobic silica, completely covered by DMS groups, codeine adsorption is considerably lower than on the bare silica, but neutral salts increase the adsorption. The adsorption of codeine is compared with the adsorption of aggregating surfactant ions. Common and different features of their interactions with silica surfaces are outlined.     

NIR studies of the surface modification in silica fillers

Methods of estimating the degree of condensation of the surface silanol groups of silica due to its modification by silane coupling agents are reported.Also, a procedure for estimating the surface silanol groups for the pre- and post-modified silicas for the NIR 7326 cm^–1 band is given.Using electron microscope studies and heats of immersion of silica surfaces, the silane effect on agglomeration of silica particles and, thus, on the physicochemical properties of its surface has been demonstrated.     

Structures and Unexpected Dynamic Properties of Phosphine Oxides Adsorbed on Silica Surfaces

Solid‐state NMR spectroscopy of selected phosphine oxides adsorbed on silica surfaces establishes the surface mobilities, even of phosphine oxides with high melting points. Crystal structures of the adducts Ph₃PO ? HOSiPh₃ and Cy₃PO ? H₂O indicate that the interactions with silica involve hydrogen bonding of the P?O group to adsorbed water and surface silanol groups.     

Dependence of surface properties of silylated silica on the length of silane arms

Amorphous precipitated Zeosil 1165 MP silica was silylated with low grafting degrees of organosilicons bearing different alkoxy and hydrocarbon tails, like monomethoxy(dimethyl)octadecylsilane (DMODMS), monomethoxytrimethylsilane (TMMS), trimethoxymercaptopropylsilane (MPTS), and 3-octanoylthio-1-propyltriethoxysilane (NXT^?). Thermogravimetry and Elemental Analysis were used to determine the degree of silane grafting and the final number of free silanol OH groups/nm² on the modified Zeosil surface. Free energy, enthalpy and entropy of adsorption of hydrocarbon probes were determined by Inverse Gas Chromatography at infinite dilution and dispersive component, $\gamma_{s}^{d}$ , and specific interaction parameter, I ^sp , of the surface tension of the silica surface were calculated. Silylation changes the hydrophilic character of Zeosil silica to the hydrophobic one, on increasing the grafting degree and, mainly, the length of hydrocarbon tail of the silane molecule (DMODMS and NXT^?). The long hydrocarbon tails practically shield the silica particle surface and the adsorbed probes preferentially interact with them. In the case of TMMS-Zeosil the adsorbed probes practically interact with the silica surface, with loss of entropy well above that of the bare silica, while being equal the values of the enthalpy of adsorption. All the other modified silicas show loss of entropy lower than that of bare silica. Steric hindrance, played by the presence of methyl groups of TMMS, is suggested to reduce the freedom of translational and rotational movements of the adsorbed probe.     

Quantitative 1H NMR analysis of reacted silanol groups in silica nanoparticles chemically modified with monochlorosilanes

Quantitative analysis of reacted silanol groups in silica nanoparticles modified chemically with monochlorosilanes was performed by ¹H NMR after treatment with cesium fluoride. Silica nanoparticles were modified chemically by the reaction between the silanol groups and monochlorosilanes, and the structure of the organic moiety anchored onto the silica surface was confirmed with solid‐state ¹³C NMR. As monochlorosilanes react with silanol groups at 1:1 ratio unlike di‐ or trichlorosilanes, the number of the silanes introduced into silica nanoparticles equals that of reacted silanol groups. Organically modified silica nanoparticles were dissolved using cesium fluoride, and the amount of the soluble organic compounds originated from the introduced silanes was determined by a ¹H NMR internal standard method using pyrene as the reference. Those values determined by ¹H NMR were in good agreement with those determined by elemental analysis. Thus, the number of reacted silanol groups per one particle was calculated on the basis of the results obtained by the ¹H NMR method, and the values were highly dependent on the steric structure of the introduced silanes. Copyright © 2010 John Wiley & Sons, Ltd.     

Adsorption of polyethylene oxide on surface modified silica – stability of bare and covered particles in suspension

 The adsorption of poly-ethylene oxide (PEO) on modified colloidal silica and the stability of the aqueous suspension was investigated. With octanol some silanol groups at the silica surface were replaced by octylgroups. The size of the modified silica particles and the charge and chemical groups on the surface were charaterized by ultracentrifugation, photon correlation spectrometry, polyelectrolyte titration and IR spectrometry. The adsorbed amounts of polyethylene oxides of different molar mass were determined on the modified silica in water. With photon correlation spectrometry (PCS) the hydrodynamic layer thickness of the PEO layers on the particles were measured. The dependences of the layer thicknesses on molar mass of the PEO, polymer concentration and adsorption time were determined. The aggregation of the suspended PEO coated and uncoated modified silica particles was examined with PCS by the time dependence of the diffusion coefficient at different salt concentrations. The influence of molar mass and concentration of PEO as well as of the age of the dispersion was explored. The measured dependences are discussed and compared with the behavior of unmodified silica- and latex-particles. Received: 6 April 1998 Accepted: 27 May 1998     

Electron spin resonance studies of spin-labelled polymers—18: Adsorption of spin-labelled poly(vinyl acetate) on silica surfaces

The adsorption of spin-labelled poly(vinyl acetate) from dilute solutions in ethyl acetate, chloroform and toluene onto three silica adsorbents of different surface silanol contents was studied. The adsorption capacities of the three silica samples, which decreased with decreasing surface silanol content, were dependent on the nature of the solvent, being greatest in the poor solvent toluene and least in the good solvent ethyl acetate. The ESR spectra of the polymer adsorbed on the silica of highest silanol content suggested that the polymer had a relatively flat conformation when toluene or chloroform was solvent and a more looped conformation when ethyl acetate was solvent. With the silica of intermediate silanol content, the polymer adsorbed from chloroform solution also had a loopy conformation. The silica of lowest silanol content was prepared by treating the first silica absorbent with trimethylchlorosilane. The line-shapes in the ESR spectrum of the labelled polymer adsorbed on this modified silica indicated a change in mode of adsorption.     

Generation of chemisorbed benzyl radicals on silica nanoparticles

Functionalized silica nanoparticles (NP) were obtained by esterification of the silanol groups of fumed silica nanoparticles with benzyl alcohol. These particles were characterized by Fourier transform infrared spectroscopy, ¹³C and ²⁹Si NMR spectroscopy, thermogravimetry, total organic carbon, Brunauer–Emmett–Teller analysis, UV-visible spectroscopy, and transmission electron microscopy. NP suspensions in water/acetonitrile mixtures were used as quenchers of benzophenone (BP) phosphorescence in time-resolved experiments at the excitation wavelength of 266 nm. The phosphorescence signals obtained in the presence of the nanoparticles were fitted to biexponential decays. Both decays were accelerated in the presence of increasing amounts of NP. A model, including the reversible adsorption of BP on the NP, which was supported by computer simulations accounts for the observed results. Laser flash-photolysis experiments with excitation at 266 nm of NP suspensions in water/acetonitrile in the presence of BP generated benzyl radicals that were attached to the silica surface. These radicals were detected at their absorption maxima (320 nm) by transient optical techniques.     

On the nature of the Brønsted acidic groups on native and functionalized mesoporous siliceous SBA-15 as studied by benzylamine adsorption from solution

The concentration and Br?nsted acidity of surface silanol groups on mesoporous silica (SBA-15) has been studied by following the adsorption of benzylamine, BA, from water as a function of pH. The adsorbed amount of BA from water was compared to the maximum amount of BA that could be adsorbed from cyclohexane. Furthermore, the surface concentration and acidity of carboxylic acid functions on surface-functionalized SBA-15 was also studied, which allowed the relative surface concentration of remaining silanols to be obtained. Two types of silanols can be identified, where about 1/5 of the silanols have a pKa 相似文献   

A Mixed Retention Model of Reversed Phase HPLC

The retention behavior of solutes in reversed phase chromatographic system, especially containing hydrophobic ions in mobile phase, has been studied by many authors, but the silanol effect on alkyl-modified silica surface was neglected. Actually, because of stereo hindrance, numerous unreacted (residual) silanol groups, which can interact with some solutes, are left within the bonded phase after the silica surface has be modified. A mixed retention model, which considers adsorbed hydrophobic ions on the bonded phase can decrease the hydrophobicity and mask residual silanol groups, is proposed, based on hydrophobic distribution of neutral solutes, ion-pair distribution of ionic solutes and coulombic attraction between cationic solutes and the dissociated silanols.     

Study of radiation-induced polymerization of vinyl monomers adsorbed on inorganic substances. VII. Effect of pretreatment temperature of silica gel on styrene–silica gel system

To investigate the reaction mechanism of radiation-induced polymerization of styrene adsorbed on silica gel, the effect of pretreatment temperature of silica gel was studied. Preheating of silica gel was carried out at 200, 500, and 800°C. The number of silanol groups of silica gel surface decreased as preheating temperature increased. The rate of polymerization on the silica gel preheated at 500°C was faster than that at 200°C, but the polymerization rate on the silica gel preheated at 800°C was the lowest. These results suggest that rate of polymerization on the silica gel is affected by the conditions of silica gel surface such as the number of silanol groups and the pore size. At the same monomer conversion, percent grafting decreased as preheating temperature of silica gel increased. The GPC spectra of both graft polymers and homopolymers have two peaks at all preheating temperatures. The monomer conversion of low molecular weight peaks of graft polymers decreased as preheating temperature of silica gel increased. This result suggests that there is a probability that the grafting sites of low molecular weight peaks of graft polymers somehow interact with silanol groups.     

Molecular macrocluster formation on silica surfaces in phenol-cyclohexane mixtures

The adsorption of phenol, an aromatic compound with a hydrogen-bonding group, onto a silica surface in cyclohexane was investigated by colloidal probe atomic force microscopy (AFM), attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and adsorption isotherm measurements. ATR-FTIR measurements on the silica surface indicated the formation of surface macroclusters of phenol through hydrogen bonding. The ATR-FTIR spectra were also measured on the H-terminated silicon surface to observe the effect of the silanol groups on the phenol adsorption. The comparison of the ATR-FTIR spectra for both the silicon oxide and H-terminated silicon surfaces proved that the silanol groups are necessary for the formation of phenol clusters on the surface. The surface force measurement using colloidal probe AFM showed a long-range attraction between the two silica surfaces in phenol-cyclohexane mixtures. This long-range attraction resulted from the contact of the adsorbed phenol layers for the phenol concentrations below 0.6 mol %, at which no significant phenol clusters formed in the bulk solution. The attraction started to decrease at 0.6 mol % phenol due to the exchange of the phenol molecules between the clusters in the bulk phase and on the surface. The surface density of phenol in the adsorbed layer was calculated on the basis of the long-range attraction and found to be much smaller than the liquid phenol density. The plausible structure of the adsorbed phenol layer was drawn by referring to the crystal structure of the bulk phenol and orientation of the phenol molecules on the surface, estimated by the dichroic analysis of ATR-FTIR spectroscopy. The investigation of the phenol adsorption on the silica surface in a nonpolar solvent using this novel approach demonstrated the effect of the aromatic ring on the surface packing density.     

Water sorption in hybrid silica gels containing colloidal nontronite

Hybrid silica gels (HSGs) were prepared according to an acid-catalyzed sol–gel method using tetraethoxysilane (TEOS) as silica precursors and colloidal suspension of nontronite clay mineral. The silica surfaces were hydrophilic in relation to silanol groups and it was of interest to increase hydrophobicity by substituting silanol by methylated groups through addition of methyltrimethoxysilane (MTMS) in a molar ratio TEOS: MTMS equaled to 1:0.4. The aim of the present paper was to predict effects of water content in soil on HSG hydration by characterizing HSG water desorption and sorption with dynamic vapor sorption device. From desorption kinetics, TEOS HSGs showed higher ability to water surface evaporation and diffusion compared to the TEOS–MTMS HSGs. After complete dehydration, water sorption isotherms Type II were obtained for HSGs. Isotherms were fitted with Brunauer-Emmett-Tellet (BET) and Guggenheim, Andersen, de Boer (GAB) models. The higher monolayer values of water adsorbed for HSGs containing nontronite suggested a major influence of clay minerals on overall hydration. However, the water binding energy depended upon the nature of silica matrix indicating weaker bonds with methylated groups at solid surface in MTMS–TEOS HSGs. Apparent water sorption diffusivities, D_app were calculated according to Fick’s diffusion model. Maximal D_app values were obtained in the range 0.2??.3 a_w after which the D_app decreased in relation with capillary condensation.     

Thermally- and photoinduced changes in the water wettability of low-surface-area silica and titania

The surface properties of silica and titania are mainly determined by the presence, density, and type of terminal hydroxyl groups (Si-OH "silanol" and Ti-OH "titanol"). Thermal treatment at elevated temperatures causes dehydroxylation on both surfaces, confirmed by streaming potential and ToF-SIMS measurements. The magnitude of the zeta potential markedly decreases after heat treatment, but the IEP is not affected. The intensity ratio MOH(+)/M(+) (M = Si or Ti), which reflects the surface density of OH groups, also decreases noticeably after high-temperature treatment. The mechanism is condensation of adjacent silanol/titanol groups into siloxane/titanoxane bonds. Ultraviolet light (lambda = 254 nm) has little effect on silica but rapidly induces hydrophilicity on titania surfaces. There is a strong correlation between the amount of hydrocarbons adsorbed on the surface and the density of titanol groups (thence the water contact angle). The effect of UV radiation can be entirely attributed to photolytic decomposition of organic contaminants. Dehydroxylated titania and silica (at 1050 degrees C) show very different wetting behavior: silica is moderately hydrophobic (water contact angle of about 40 degrees), while titania is hydrophilic (0 degrees). This dissimilarity can be explained with a simple model estimating the van der Waals and acid-base interfacial interactions.     

Study of cooperative effects of silanols on modified silica by dielectric relaxation method

Two types of chemically modified silica gels with covalently bonded hydrophobic (alkyl, SiO₂-C₈) and hydrophilic (aminoalkyl, SiO₂-NH₂) groups were studied by dielectric relaxation method. For SiO₂-C₈ two relaxation maxima were detected at 140 and 238K. From comparison with bulk silica the lower temperature maximum was assigned to cooperative re-orientation of residual silanols and higher one to melting of physically adsorbed water. Both maxima are much weaker for SiO₂-C₈ then for bulk silica. In Arrhenius coordinates relaxation at 238K exhibits similar behavior as OH groups in polyvinyl alcohol and so it was assigned to mobility of orientation defects in mono-dimensional chain of physically adsorbed water. For SiO₂-NH₂ no low temperature relaxation effect was observed. Intensive relaxation was measured at 248 K only. Strong interaction between supramolecules of silanol groups, bonded aminogroups and adsorbed water was assumed.     

Deactivation of silica surfaces with a silanol-terminated polysiloxane; structural sharacterization by inverse gas chromatography and solid-state NMR

Retention gape deactivated with Silicone OV-1701-OH show good chromatographic performance and remarkable stability against water induced stationary phase degradrdation. In an attempt to better understand the findamentals off the deactivation process using silanol terminated polysiloxanes, a fumed silica was deactivated with Silicon OV-1701-OH. In contrast to fused silic capillaries, fumed silica (Aerosil A-200) can be studied by ²⁹Si cross-polarization magic-angle-spinning (CPMAS) NMR, thus serving as a model substrate for fused silica. Retention data from inverse gas chromatography at infinite dilurion and ²⁹Si CP MAS NMR data of five Aerosil phases, differing in residual silanol surface concentration, are correlated with the aim of validating this approach for stationary phase characterization. A comparatively detailed model of the deactivating polymer layer that explains the observed absorption activities is deduced. Surface silanols are shown to play a key role in the polymer layer, the structure of which is of primary importance for the absorption behavior after deactivation. Contrary to common belief, the absolute silanol surface concentration after deativation is only of secondary importance for the overall absorption activity. High silanol surface concentrations enhance degradation of the polysiloxane chains into small cyclic fragments as well as subsequent absorption and immobolization to the silica substrate surface. The mobility of linear polysiloxane chains in the kHz regime (as determined bby NMR cross-polarization dynamics) appears to determine the extent which the residual silanols are accessible for analytes. It is therefore anticipated that there is an optimum silanol surface concentration of fused silica surfaces to be deactivated with silanol terminated polysiloxanes; it should be lazrge enough to adsord polymer fragments, but not large to avoid excessive residual silanol activity.     

The structure of water and methanol adsorbed on silica gel by FT-NIR spectroscopy

The NIR adsorption spectra were analyzed quantitatively on the fundamental, combination and first overtone region of OH vibrations of silanol groups, water and methanol adsorbed on mesoporous silica gels. Adsorbed methanol constitutes first layer of about 3 molecules/um^–2 and second layer, the structure of which is similar to that of bulk methanol liquid. Adsorbed water consists of a first layer of about 3 molecules/nm^–2, the second layer of about 9 molecules/nm^–2 and the third layer has a structure similar to the that of bulk water. The molecular configuration at the interface is discussed.     

Adsorption behaviour and surfactant elution of cationic salivary proteins at solid/liquid interfaces,studied by in situ ellipsometry

Adsorption of the cationic salivary proteins lactoferrin, lactoperoxidase, lysozyme and histatin 5 to pure (hydrophilic) and methylated (hydrophobized) silica surfaces was investigated by in situ ellipsometry. Effects of concentration (≤10 μg ml⁻¹, for lysozyme ≤200 μg ml⁻¹) and dependence of surface wettability, as well as adsorption kinetics and elutability of adsorbed films by buffer and sodium dodecyl sulphate (SDS) solutions were investigated. Results showed that the amounts adsorbed decreased in the order lactoferrin ≥ lactoperoxidase > lysozyme ≥ histatin 5. On hydrophilic silica, the adsorption was most likely driven by electrostatic interactions, which resulted in adsorbed amounts of lactoferrin that indicated the formation of a monolayer with both side-on and end-on adsorbed molecules. For lactoperoxidase the adsorbed amounts were somewhat higher than an end-on monolayer, lysozyme adsorption showed amounts corresponding to a side-on monolayer, and histatin 5 displayed adsorbed amounts in the range of a side-on monolayer. On hydrophobized substrata, the adsorption was also mediated by hydrophobic interactions, which resulted in lower adsorbed amounts of lactoferrin and lactoperoxidase; closer to side-on monolayer coverage. For both lysozyme and histatin 5 the adsorbed amounts were the same as on the hydrophilic silica. The investigated proteins exhibited fast adsorption kinetics, and the initial kinetics indicated mass transport controlled behaviour at low concentrations on both types of substrates. Buffer rinsing and SDS elution indicated that the proteins in general were more tightly bound to the hydrophobized surface compared to hydrophilic silica. Overall, the surface activity of the investigated proteins implicates their importance in the salivary film formation.