Oxidation of methanol catalyzed by silica-supported polystannazane–copper complex

Silica-supported polystannazane–copper complex has been prepared and used as a catalyst for the oxidation of methanol. The results showed that the catalyst could catalyze the oxidation of methanol to formaldehyde at a high yield and selectivity at 30°C and under 1 atm mild conditions. The N/Cu mole ratio in the complex, temperature and the amount of NaOH additive had much influence on the catalytic activity. The complex was stable during the reaction and could be used repeatedly.     

X‐ray photoelectron spectroscopy study of oxygen‐containing polymer [poly(vinyl methyl ether), poly(vinyl methyl ketone), and poly(methyl methacrylate)] surfaces metalized by vacuum‐deposited nickel

Surfaces of poly(vinyl methyl ether) (PVME), poly(vinyl methyl ketone) (PVMK), and poly(methyl methacrylate) (PMMA) were covered with different thicknesses of nickel with a metal‐vapor‐condensation method, and the metal–polymer interfaces were analyzed by X‐ray photoelectron spectroscopy. In the very first steps of the metalization, it was found that a systematic degradation of the polymer surface occurs through CO or CO₂ losses, depending on the polymer functionalities. Then, at the interface with the polymer, the condensed metal reacts by oxidization with the oxygen atoms that are still available after the surface degradation. Nickel oxide is then formed at the interface, whatever the nature of the initial polymer functional group. These new oxide species are not chemically bonded to the polymer structure, and their formation is not affected by the type of bond existing between oxygen and carbon atoms in the original polymer. Finally, the accumulation of metal on the substrate induces an amorphization of the polymer carbon structure because thermal energy is transferred from the metal coating to the polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 82–94, 2002     

Interest and durability of multilayers: from model films to complex films

In a first part, this paper focuses on the interest of using a multilayer for vacuum insulation panels envelope. It is shown that piling up layers of metallized poly(ethylene terephthalate) does not seem to improve the initial barrier performance. In parallel, a permeation model to predict barrier properties of multilayer films was developed and validated with experimental results. In a second part, durability of a multilayer composite was investigated using accelerated hydrothermal ageing tests. It is shown that physical properties and in particular barrier properties decrease with ageing time. Polyurethane layer used as adhesive system in multilayer films is responsible for complete degradation of aluminum layer after 6 ageing months at 70°C – 90% relative humidity. Copyright © 2009 John Wiley & Sons, Ltd.     

Conductivity,structure, and thermal properties of chitosan‐based polymer electrolytes with nanofillers

This paper focus on the effect of nanosize (<50 nm BET) inorganic alumina (Al₂O₃) filler on the structural, conductivity, and thermal properties of chitosan‐based polymer electrolytes. Films of chitosan and its complexes were prepared using solution‐casting technique. Different amounts of Al₂O₃ viz., 3, 4.5, 6, 7.5, 9, 12, and 15 wt% were added to the highest room temperature conducting sample in the chitosan–salt system, i.e. sample containing 60 wt% chitosan–40 wt% NH₄SCN. The conductivity value of the sample is 1.29 × 10^?4 S cm^?1. On addition of 6 wt% Al₂O₃ filler the ionic conductivity increased to 5.86 × 10^?4 S cm^?1. The amide and amino peaks in the spectrum of chitosan at 1636 and 1551 cm^?1, respectively, shift to lower wavenumbers on addition of salt. The glass transition temperature T_g for the highest conducting composite is 190°C. The increase in T_g with increase in more than 6 wt% filler content is attributed to the increase in degree of crystallinity as proven from X‐ray diffraction studies. Copyright © 2009 John Wiley & Sons, Ltd.     

Dimensional instabilities of polyester and polyolefin films as origin of delamination in laminated multilayer

Polymer–metal multilayer films provide attractive barrier properties to air and water, provided by several films bonded together. Used in high temperature and humidity, the delamination is the most common degradation mechanism. This mode of failure is critical because it leads to premature loss of barrier properties. Therefore, delaminations limit the use of multilayer in these conditions. Delamination should result from interfacial shear stress, and plausibly from difference of shrinkage of the films, due to relaxation of internal stress. A method was developed for measuring the deformations of each individual film. The measurements indicate that the shrinkage is anisotropic and controls the decohesion in the multilayer. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 309–319     

Determination of thermodynamic properties of macroporous glycidyl methacrylate‐based copolymers by inverse gas chromatography

Macroporous crosslinked poly(glycidyl methacrylate‐co‐ethylene glycol dimethacrylate) (PGME) was synthesized by suspension copolymerization and modified by ring‐opening reaction of the pendant epoxy groups with ethylene diamine (EDA). Inverse gas chromatography (IGC) at infinite dilution was applied to determine the thermodynamic interactions of PGME and modified copolymer, PGME‐en. The specific surface areas of the initial and modified copolymer samples were determined by the BET method, from low‐temperature nitrogen adsorption isotherms. The specific retention volumes, V, of 10 organic compounds of different chemical nature and polarity (nonpolar, donor, or acceptor) were determined in the temperature range 333–413 K. The weight fraction activity coefficients of test sorbates, , and Flory–Huggins interaction parameters, , were calculated and discussed in terms of interactions of sorbates with PGME and PGME‐en. Also, the partial molar free energy, , partial molar heat of mixing, , sorption molar free energy, ΔG, sorption enthalpy ΔH, and sorption entropy, ΔS, were calculated. Glass transitions in PGME and PGME‐en, determined from IGC data, were observed in the temperature range 373–393 K and 363–373 K, respectively. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2524–2533, 2005     

Enhanced thermal conductivity of epoxy–matrix composites with hybrid fillers

The results of thermal conductivity study of epoxy–matrix composites filled with different type of powders are reported. Boron nitride and aluminum nitride micro‐powders with different size distribution and surface modification were used. A representative set of samples has been prepared with different contents of the fillers. The microstructure was investigated by SEM observations. Thermal conductivity measurements have been performed at room temperature and for selected samples it was also measured as a function of temperature from 300 K down to liquid helium temperatures. The most spectacular enhancement of the thermal conductivity was obtained for composites filled with hybrid fillers of boron nitride–silica and aluminum nitride–silica. In the case of sample with 31 vol.% of boron nitride–silica hybrid filler it amounts to 114% and for the sample with 45 vol.% of hybrid filler by 65% as compared with the reference composite with silica filler. However, in the case of small aluminum nitride grains application, large interfacial areas were introduced, promoting creation of thermal resistance barriers and causing phonon scattering more effective. As a result, no thermal conductivity improvement was obtained. Different characters of temperature dependencies are observed for hybrid filler composites which allowed identifying the component filler of the dominant contribution to the thermal conductivity in each case. The data show a good agreement with predictions of Agari‐Uno model, indicating the importance of conductive paths forming effect already at low filler contents. Copyright © 2014 John Wiley & Sons, Ltd.     

Polymer Composites for Thermoelectric Applications

This review covers recently reported polymer composites that show a thermoelectric (TE) effect and thus have potential application as thermoelectric generators and Peltier coolers. The growing need for CO₂‐minimizing energy sources and thermal management systems makes the development of new TE materials a key challenge for researchers across many fields, particularly in light of the scarcity or toxicity of traditional inorganic TE materials based on Te and Pb. Recent reports of composites with inorganic and organic additives in conjugated and insulating polymer matrices are covered, as well as the techniques needed to fully characterize their TE properties.     

Catalytic behaviors of magnesia-supported polytitanazane–platinum complex on the oxygenation of 3-heptanol

A kind of inorganic polymer–platinum complex, magnesia-supported polytitanazane–platinum complex (MgO-Ti-N–Pt), was prepared and used to catlayze the oxygenation of 3-heptanol. It was found that this kind of catalyst was very active and stable in the reaction. The objective product (3-heptanone) was obtained near 100% yield in 40 hr under moderate reaction temperature and atmospheric oxygen pressure.     

Controlled‐release systems based on the intercalation of polymeric metribuzin onto montmorillonite

A series of polymer–clay composites carrying metribuzin as herbicide moieties were prepared. Linear copolymers containing metribuzin via an imide linkage were prepared by the free‐radical polymerization of metribuzin monomer (N,N‐diacryloyl metribuzin) with different comonomers. The intercalation of the copolymers onto montmorillonite through a cationic exchange process was carried out and yielded metribuzin composite products. The prepared materials were characterized with a wide variety of analytical techniques, including gel permeation chromatography, NMR, IR, elemental microanalysis, gravimetric analysis (calcination), and swelling measurements. The release rates for the prepared materials were investigated in media of different pHs with an ultraviolet spectrophotometer. Also, these compounds were studied for the control of herb growth. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2513–2525, 2002     

Polymeric Selectin Ligands Mimicking Complex Carbohydrates: From Selectin Binders to Modifiers of Macrophage Migration

Novel polymeric cell adhesion inhibitors were developed in which the selectin tetrasaccharide sialyl‐Lewis^X (SLe^X) is multivalently presented on a biocompatible poly(2‐hydroxypropyl)methacrylamide (PHPMA) backbone either alone (P1) or in combination with O‐sulfated tyramine side chains (P2). For comparison, corresponding polymeric glycomimetics were prepared in which the crucial “single carbohydrate” substructures fucose, galactose, and sialic acid side chains were randomly linked to the PHPMA backbone (P3 or P4 (O‐sulfated tyramine)). All polymers have an identical degree of polymerization, as they are derived from the same precursor polymer. Binding assays to selectins, to activated endothelial cells, and to macrophages show that polyHPMA with SLe^X is an excellent binder to E‐, L‐, and P‐selectins. However, mimetic P4 can also achieve close to comparable binding affinities in in vitro measurements and surprisingly, it also significantly inhibits the migration of macrophages; this provides new perspectives for the therapy of severe inflammatory diseases.     

Segmental dynamics of poly(styrene-b-2-vinylpyridine) in bulk and at the surface/air interface

Anionically polymerized poly(α-deuterostyrene) and poly(β-deuterostyrene-b-2-vinylpyridine) (DSVP), selectively deuterated on the styrene backbone, were studied using deuterium wide-line NMR in bulk and adsorbed on silica and alumina. Changes in the segmental dynamics of the bulk and adsorbed polymers were inferred via changes in the NMR line shape with temperature. The DSVP bulk sample, which consisted of micellar aggregrates with a 2-vinylpyridine core, was more rigid than the homopolystyrene of a similar molecular weight. A significant change in mobility occurred at 20°C higher in the DSVP bulk sample than it did in homopolystyrene. The DSVP-adsorbed sample showed more restrictive mobility than bulk DSVP. The spectra of the adsorbed samples contained “rigid” Pake patterns with considerable intensity at temperatures where the collapse of the Pake pattern for the DSVP bulk sample was observed. DSVP bound to the silica surface was found to have a mobility similar to the same copolymer on alumina. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1609–1616, 1998     

New anti‐bacterial polychelates: synthesis,characterization, and anti‐bacterial activities of thiosemicarbazide–formaldehyde resin and its polymer–metal complexes

New polymeric ligand (resin) was prepared by the condensation of thiosemicarbazides with formaldehyde in the presence of acidic medium. Thisemicarbazide–formaldehyde polymer–metal complexes were prepared with Mn(II), Co(II), Ni(II), Cu(II) and Zn(II) in 1:2 metal:ligand molar ratio. The polymeric ligand and its polymer–metal complexes were characterized by elemental analysis, thermogravimetric analysis (TGA), FTIR, ¹³C NMR and ¹H NMR. The geometry of central metal ions was conformed by electronic (UV–vis) and EPR spectra. The antibacterial activities of all the synthesized polymers were investigated against Bacillus subtilis and Staphylococcus aureus (Gram‐positive) and Escherichia coli and Salmonella typhi (Gram‐negative). These compounds showed excellent activities against these bacteria using the shaking flask method. Copyright © 2008 John Wiley & Sons, Ltd.     

Polymers for targeted and/or sustained drug delivery

Recent advances in the use of polymers for passive targeting of drugs attached or incorporated into polymeric species (enhanced permeability and retention, EPR) as well as active targeting of drugs by ligands or antibodies of receptors overexpressed on the surface of the targeted cells, is discussed in the present review. Examples of sustained, slow release of a drug incorporated into a polymeric matrix are cited. Drugs used for passive modes of targeting have been described in the context of polymer‐drug conjugates, drugs in the polymer coated liposomes, and drugs inserted into polymeric micelles. Active targeting of the drugs and their internalization by receptors, on the surface of the targeted cells, was also discussed. Release of the drugs inside cells, after are broken the environmentally sensitive links attaching them to polymeric platforms was described. Examples illustrate targeting drug by local heat generated by ultrasound, or by photodynamic treatment. Delivery modes of drugs incorporated into other nanoparticles and the concept of prodrugs have been investigated. Copyright © 2008 John Wiley & Sons, Ltd.     

Investigation of clay modifier effects on the structure and rheology of supercritical carbon dioxide‐processed polymer nanocomposites

Superior property enhancements in polymer–clay nanocomposites can be achieved if one can significantly enhance the nanoclay dispersion and polymer–clay interactions. Recent studies have shown that nanoclays can be dispersed in polymers using supercritical carbon dioxide (scCO₂). However, there is need for a better understanding of how changing the clay modifier affects the clay dispersability by scCO₂ and the resultant nanocomposite rheology. To address this, the polystyrene (PS)/clay nanocomposites with “weak” interaction (Cloisite 93A clay) and “strong” interaction (Cloisite 15A clay) have been prepared using the supercritical CO₂ method in the presence of a co‐solvent. Transmission electron microscopy images and small‐angle X‐ray diffraction illustrate that composites using 15A and 93A clays show similar magnitude of reduction in the average tactoid size, and dispersion upon processing with scCO₂. When PS and the clays are coprocessed in scCO₂, the “dispersion” of clays appears to be independent of modifier or polymer–clay interaction. However, the low‐frequency storage modulus in the scCO₂‐processed 15A nanocomposites is two orders of magnitude higher than that of 93A nanocomposites. It is postulated that below percolation (solution blended composites), the strength of polymer–clay interaction is not a significant contributor to rheological enhancement. In the scCO₂‐processed nanocomposites the enhanced dispersion passes the percolation threshold and the interactions dictate the reinforcement potential of the clay–polymer–clay network. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 823–831, 2010     

Swelling of polyacrylamide gels in polyacrylamide solutions

Swelling behavior of polyacrylamide (PAAm) and polyacrylamide-co-polyacrylic acid (PAAm-co-PAAc) gels was investigated in aqueous solutions of monodisperse PAAms with molecular weights (M_w) ranging from 1.5 × 10³ to 5 × 10⁶ g/mol. The volume of the gels decreases as the PAAm concentration in the external solution increases. This decrease becomes more pronounced as the molecular weight of PAAm increases. The classical Flory–Huggins (FH) theory correctly predicts the swelling behavior of nonionic PAAm gels in PAAm solutions. The polymer–polymer interaction parameter χ₂₃ was found to decrease as the molecular weight of PAAm increases. The swelling behavior of PAAm-co-PAAc gels in PAAm solutions deviates from the predictions of the FH theory. This is probably due to the change of the ionization degree of AAc units depending on the polymer concentration in the external solution. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1313–1320, 1998     

Influence of the physical characteristics of the polymer on the glass transition of various chemically modified PVCs

Vinylchloride–vinylthiocresol and vinylchloride–vinylthionaphthol copolymers of various compositions were prepared by the substitution reaction of PVC with sodium thiocresol and sodium thionaphthol, respectively, in different solvents and at different temperatures. The variation of the glass transition temperature of these copolymers with chemical com-position does not follow the Flory–Fox equation, but is found to depend on the solvent and the temperature at which the copolymer is obtained. The comonomer sequence distribution and stereosequence content of the above copolymers, and those of vinylchloride–vinyl-thiobenzene copolymer, were determined by ¹H- and ¹³C-NMR spectroscopy. The depen-dence of comonomer distribution and stereoregularity content with chemical composition for the three series of copolymers, prepared in different solvents and temperatures, are similar. The T_g deviations for the three series of copolymers were attributed to the con-tribution of physical characteristics of the PVC structure, originating from polymer–solvent interactions. © 1995 John Wiley & Sons, Inc.     

Carbon–silica dual‐phase filler,a new‐generation reinforcing agent for rubber. Part VI. Time–temperature superposition of dynamic properties of carbon–silica‐dual‐phase‐filler‐filled vulcanizates

Dynamic properties such as shear modulus, loss modulus, and loss factor were obtained at a low strain amplitude over a wide range of frequencies and temperatures on vulcanizates filled with carbon black, silica, and carbon–silica dual‐phase filler. The data were shifted along the frequency scale. Instead of a single smooth master curve, a pseudomaster curve with a feather‐like structure is obtained. This effect is especially pronounced for the loss factor. Multiple factors may be responsible for this. Among others, filler networking and polymer–filler interaction may play a dominant role. The effect of the carbon–silica dual‐phase filler on the overall dynamic properties of the vulcanizates is similar to that of silica. Their tan δ values are much lower at lower frequencies and are relatively higher at higher frequencies. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1240–1249, 2000     

Radiation-induced graft polymerization of acrylic acid onto fluorinated polymers. II. Graft copolymer–metal complexes obtained by radiation grafting onto poly(tetrafluoroethylene-ethylene) copolymer

A study has been made on the graft copolymers obtained by radiation-induced grafting of acrylic acid onto poly(tetrafluoroethylene-ethylene) (ET) films. The conversion of the graft copolymer into metal acrylate copolymer complex was carried out by treatment with different metal salts. Such a prepared graft copolymer–metal complex was confirmed by different methods: IR, UV spectrometry, degree of coloration, and x-ray fluorescence. Some selected properties of the graft copolymer–metal complexes such as electrical conductivity, swelling behavior, and mechanical properties were investigated. The influence of metal complexes in the graft copolymers was determined and compared with the grafted films. The possibility of the practical uses for such prepared graft copolymer–metal complexes was discussed and determined. It was assumed that such materials may be of great interest in the field of semiconducting materials in addition to their applicability as cation-exchange membranes. © 1993 John Wiley & Sons, Inc.