Improved thermosets obtained from cycloaliphatic epoxy resins and γ‐butyrolactone with lanthanide triflates as initiators. I. Study of curing by differential scanning calorimetry and Fourier transform infrared

3,4‐Epoxycyclohexylmethyl 3,4‐epoxycyclohexane carboxylate was cured with different proportions of γ‐butyrolactone with lanthanum, samarium, and ytterbium triflates as catalysts. The curing was studied with differential scanning calorimetry (DSC) and Fourier transform infrared in the attenuated‐total‐reflection mode (FTIR/ATR). FTIR/ATR was used to monitor the competitive reactive processes and to quantify the evolution of the epoxide, lactone, and intermediate spiroorthoester groups. The glass‐transition temperature of the crosslinked materials was high and increased when the proportion of lactone decreased. The kinetics were studied with DSC experiments and were analyzed with isoconversional procedures. The differences in the reactivities of the systems were related to the Lewis acidity of the lanthanide salt used as the initiator. An increase in the proportion of lactone produced an increase in the reaction rate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2337‐2347, 2005     

Structural and phenomenological study on the cationic curing of mixtures of epoxy resin and 5,5‐dimethyl‐1,3‐dioxane‐2‐one

Ytterbium and lanthanum triflates were used as initiators to cure a mixture of diglycidylether of bisphenol A (DGEBA) and 5,5‐dimethyl‐1,3‐dioxane‐2‐one (DMTMC). The evolution of the curing was studied by differential scanning calorimetry (DSC) and Fourier transform infrared in the attenuated‐total‐reflection mode (FTIR/ATR). FTIR/ATR was used to monitor the competitive reactive processes and to quantify the evolution of the groups involved in the curing process. We observed the formation of a five‐membered cyclic carbonate, which remains unreacted at the chain ends because of an equilibrium process between the spiroortho carbonates that had formed as intermediate species and also the loss of CO₂, which was quantified by thermogravimetry. The kinetics were studied by DSC and analyzed by isoconversional procedures. Thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA) experiments were used to evaluate the properties of the thermosets obtained. The phenomenological changes that take place during curing were studied and represented in a time‐temperature‐transformation (TTT) diagram. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4546–4558, 2006     

N,N‐dimethylaminopyridine as initiator in the copolymerization of diglycidylether of bisphenol A with six‐membered cyclic carbonates

N,N‐Dimethylaminopyridine (DMAP) was used as initiator to cure mixtures of diglycidylether of bisphenol A (DGEBA) and 1,3‐dioxan‐2‐one (TMC) or 5,5‐dimethyl‐1,3‐dioxan‐2‐one (DMTMC). The curing was studied by differential scanning calorimetry (DSC) and Fourier transform infrared in the attenuated‐total‐reflection mode (FTIR/ATR). FTIR/ATR was used to monitor the competitive reactive processes and to quantify the evolution of the groups involved in the curing. We observed the formation of five‐membered cyclic carbonates and anionic carbonate groups that remain unreacted at the chain ends. The formation of these groups was explained by the attack of the anionic propagation species on the methylene carbon of the carbonate group, which leads to an alkyl‐oxygen rupture. By performing the cure in the thermobalance we could evaluate the loss of CO₂ produced in the samples containing carbonates. The kinetics were studied by DSC and analyzed with isoconversional procedures. The addition of carbonates slows down the curing rate. Thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA) experiments were used to evaluate the properties of the materials obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2873–2882, 2006     

Cationic copolymerization of cycloaliphatic epoxy resin with a spirobislactone with lanthanum triflate as initiator: I. Characterization and shrinkage

3,4‐Epoxycyclohexylmethyl 3,4‐epoxycyclohexane carboxylate (ECH) was cured with different proportions of 1,6‐dioxaspiro [4,4]nonane‐2,7‐dione (s(γ‐BL)) using lanthanum triflate as a catalyst. The shrinkage undergone during curing was monitored by means of thermomechanical analysis (TMA) in isothermal experiments. Fourier transform infrared spectroscopy in attenuated‐total‐reflection mode (FTIR/ATR) was used to study the evolution of lactone, epoxide, and intermediate spiroorthoester (SOE) groups to identify the different reactions that take place during the curing process. DSC was used to study the thermal characteristics of the curing process and to assess the glass‐transition temperature (T_g) of the cured material. The dynamic mechanical properties of the cured material were determined based on the data obtained by DMTA. An increase in the proportion of s(γ‐BL) led to a decrease in the gelation time and the shrinkage after gelation. By combining the data obtained by TMA and FTIR/ATR, it was also possible to identify the reactive processes responsible for the shrinkage. It was observed that an increase in the proportion of s(γ‐BL) also increases the speed of the curing process and modifies the structure of the material, thus giving rise to more flexible materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3421–3432, 2005     

Crosslinking study of mixtures of DGEBA and 1,3‐dioxan‐2‐one catalyzed by lanthanide triflates

Ytterbium and lanthanum triflates were used as catalysts to cure diglycidylether of bisphenol A with different proportions of 1,3‐dioxan‐2‐one. The curing was studied by differential scanning calorimetry (DSC) and Fourier transform infrared in the attenuated‐total‐reflection mode (FTIR/ATR). FTIR/ATR was used to monitor the competitive reactive processes and to quantify the evolution of the groups involved in the curing process. We observed the formation of a five‐membered cyclic carbonate that remains unreacted at the chain ends, because of an equilibrium process between the spiroorthocarbonates that had formed as intermediate species. The kinetics were studied by DSC experiments and analyzed with isoconversional procedures. The system catalyzed by ytterbium triflate had a higher curing rate. Thermogravimetric analysis and dynamic mechanical thermal analysis experiments were used to evaluate the properties of the materials obtained. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5799–5813, 2005     

Novel thermosets obtained by UV‐induced cationic copolymerization of DGEBA with an spirobislactone

The photocuring process of the diglycidyl ether of bisphenol A (DGEBA) with the bislactone 1,6‐dioxaspiro[4,4]nonane‐2,7‐dione (s(γ‐BL)) was studied. Triarylsulfonium hexafluoroantimonate was employed as photoinitiator. FTIR/ATR was used to study the evolution of epoxy, lactone, and intermediate spiroorthoester groups to identify the different reactions that take place during the photocuring process. Photo‐DSC and DSC were used to study the thermal evolution of the photocuring process and to assess the T_g of the fully cured material. Thermogravimetric analysis (TGA) was used to determine the thermal stability of the fully cured material. The thermomechanical properties of the materials were investigated using dynamic mechanical‐thermal analysis. Shrinkage undergone during photocuring and gelation was studied with TMA. A strong influence of the photocuring temperature on the photocuring process of the DGEBA‐ s(γ‐BL) system was observed. Differences in the reactivity of the different species were observed with respect to the thermally cured system using ytterbium triflate as cationic thermal initiator. As a consequence, photocured materials exhibited a superior thermal stability and lower flexibility. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5446–5458, 2007     

Synthesis of a new diglycidylic Meldrum acid derivative and study of the curing with lanthanide triflates as initiators

A new epoxy resin derived from Meldrum acid (DGMA) was synthesized by a two steps synthetic procedure and structurally characterized by the usual spectroscopic techniques and elemental analysis. Ytterbium and lanthanum triflates were tested as cationic initiators to cure this resin and its mixtures with diglycidylether of bisphenol A (DGEBA) in several proportions. By FTIR‐ATR spectroscopy the evolution of the groups, which participate in the curing was followed. The evolution of the curing and the T_g of the materials were studied by differential scanning calorimetry and the kinetic parameters were calculated applying isoconversional procedures. Ytterbium triflate led to a quicker curing than lanthanum. The thermal stability of the materials obtained was evaluated by thermogravimetry and the higher thermal degradability of the materials containing DGMA was confirmed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3088–3097, 2008     

New poly(ether‐ester) thermosets obtained by cationic curing of DGEBA and 7,7‐dimethyl‐6,8‐dioxaspiro[3.5] nonane‐5,9‐dione with several Lewis acids as initiators

Scandium, ytterbium, and lanthanum triflates and boron trifluoride monoethylamine were used as cationic initiators to cure a mixture 2:1 (mol/mol) of diglycidylether of bisphenol A (DGEBA) and 7,7‐dimethyl‐6,8‐dioxaspiro[3.5]nonane‐5,9‐dione (MCB). The evolution of the epoxy and lactone during curing and the linear ester groups in the final materials were evaluated by Fourier Transform Infrared in the attenuated‐total‐reflection mode. The kinetic parameters of the curing process were calculated from DSC analysis applying isoconversional procedures. The shrinkage on curing and the thermal degradability of the materials on varying the initiator used were evaluated. The expandable character of MCB was confirmed. The materials obtained were more degradable than conventional epoxy resins due to the tertiary ester groups incorporated in the network by copolymerization. © 2008 Wiley Periodicals, Inc J Polym Sci Part A: Polym Chem 46: 1229–1239, 2008     

Concerted reactions of aldehyde groups during polymerization of an aldehyde‐functional benzoxazine

Polymerization reactions of a new aldehyde‐functional benzoxazine (4HBA‐a) were investigated in detail. The curing behavior of 4HBA‐a was studied by differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) methods. The results indicate that the disappearance of the aldehyde group from 4HBA‐a and the ring‐opening reaction of 4HBA‐a occur simultaneously. Gases evolved during the curing process of 4HBA‐a were analyzed by thermogravimetric analyzer interfaced with FTIR spectra. The elimination of CO₂ is attributed to the oxidation and decarboxylation of the aldehyde groups. In addition, the crosslink sites of the aldehyde groups in the polymer structure are confirmed by model reactions. A possible reactive position should be sited in ortho position of phenol rather than ortho and/or para positions of N‐phenyl ring. Finally, the crosslinked structures of polymerized 4HBA‐a have been proposed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Reduction of the shrinkage of thermosets by the cationic curing of mixtures of diglycidyl ether of bisphenol A and 6,6‐dimethyl‐(4,8‐dioxaspiro[2.5]octane‐5,7‐dione)

Ytterbium and lanthanum triflates were used as initiators to cure mixtures of diglycidyl ether of bisphenol A and 6,6‐dimethyl‐(4,8‐dioxaspiro[2.5]octane‐5,7‐dione) in several proportions. The evolution of the epoxy and 6,6‐dimethyl‐(4,8‐dioxaspiro[2.5]octane‐5,7‐dione) bands during curing and the linear ester groups in the final materials were evaluated with Fourier transform infrared in the attenuated‐total‐reflection mode. The use of a conventional cationic initiator, boron trifluoride monoethylamine, was also studied to test the advantages of lanthanide triflates. The shrinkage after curing and the thermal degradability of the materials with variations in the comonomer ratio and the initiator were evaluated and related to the chemical structure of the final network. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6869–6879, 2006     

Thermal curing behavior of MWCNT modified vinyl ester‐polyester resin suspensions prepared with 3‐roll milling technique

This study aims to investigate the curing behavior of a vinyl ester‐polyester resin suspensions containing 0.3 wt % of multiwalled carbon nanotubes with and without amine functional groups (MWCNTs and MWCNT‐NH₂). For this purpose, various analytical techniques, including Differential Scanning Calorimetry (DSC), Fourier infrared spectroscopy (FTIR), Raman Spectroscopy, and Thermo Gravimetric Analyzer (TGA) were conducted. The resin suspensions with carbon nanotubes (CNTs) were prepared via 3‐roll milling technique. DSC measurements showed that resin suspensions containing CNTs exhibited higher heat of cure (Q), besides lower activation energy (E_a) when compared with neat resin. For the sake of simplicity of interpretation, FTIR investigations were performed on neat vinyl ester resin suspensions containing the same amount of CNTs as resin. As a result, the individual fractional conversion rates of styrene and vinyl ester were interestingly found to be altered dependent on MWCNTs and MWCNT‐NH₂. The findings obtained from RS measurements of the cured samples are highly proportional to those obtained from FTIR measurements. TGA measurements revealed that CNT modified nanocomposites have higher activation energy of degradation (E_d) compared with the cured polymer. The findings obtained revealed that CNTs with and without amine functional groups alter overall thermal curing response of the surrounding matrix resin, which may probably impart distinctive characteristics to mechanical behavior of the corresponding nanocomposites achieved. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1511–1522, 2009     

New thermosets obtained by the cationic copolymerization of diglycidyl ether of bisphenol A with γ‐caprolactone with an improvement in the shrinkage. I. Study of the chemical processes and physical characteristics

Diglycidyl ether of bisphenol A was cured with different proportions of γ‐caprolactone with ytterbium triflate as an initiator. The curing was studied by means of differential scanning calorimetry and Fourier transform infrared in the attenuated total reflection mode. The latter was used to monitor the competitive reactive processes and to quantify the conversions of the epoxide, lactone, and intermediate spiroorthoester groups. A partial depolymerization process from the cured material to free γ‐caprolactone was also identified. The formation of a stable carbocation and the coordinative capability of ytterbium triflate were the reasons for this unexpected process. The thermal and dynamic mechanical properties of the cured materials were determined with differential scanning calorimetry, thermogravimetric analysis, and dynamic mechanical thermal analysis. An increase in the proportion of γ‐caprolactone resulted in an increased curing rate, a decrease in the shrinkage after gelation, and a significant decrease in the glass transition temperature. The introduction of ester linkages into the three‐dimensional structure led to more thermally degradable thermosets. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1968–1979, 2007     

Microstructure and protonic conductivity of H3PO4‐doped polyethylenimine–siloxane chemically covalently organic–inorganic hybrids

The chemically covalent polyethylenimine–siloxane hybrids doped with various amounts of ortho‐phosphoric acid (H₃PO₄) were prepared and characterized by FTIR, DSC, TGA, and solid‐state NMR spectra. The protonic conduction behavior of these materials was also investigated by means of impedance measurements. These observations indicate that the hydrogen bonding and protonic interactions exist between the dopant H₃PO₄ and the hybrid host, resulting in an increase in T _g of polyethylenimine segments. These hybrids are thermally stable up to 200 °C from TGA analysis. Conductivity studies show an Arrhenius behavior characteristic and the Grotthus‐like proton conduction, and a high conductivity of 10^?2–10^?3 S cm^?1 at 110 °C in dry atmosphere for the hybrid membrane with H₃PO₄/EI of 0.5. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2135–2144, 2006     

New thermosets obtained from DGEBA and Meldrum acid with lanthanum and ytterbium triflates as cationic initiators

Ytterbium and lanthanum triflates were used as cationic initiators to cure mixtures of diglycidylether of bisphenol A (DGEBA) and Meldrum acid (MA) in several proportions of comonomers and initiators. The evolution of epoxy and lactone groups during curing, and of linear ester formed in the final materials were evaluated by Fourier transform infrared in the attenuated-total-reflection mode (FTIR/ATR).

The global evolution of the curing process was investigated by calorimetric analysis and the activation energy was calculated by isoconversional procedures.

Shrinkage on curing and thermal degradability of the final materials on varying the initiator and the proportion of Meldrum acid in the mixtures were evaluated. The expandable character of MA was confirmed. The materials obtained were more degradable than conventional epoxy resins due to the tertiary ester groups incorporated into the network by copolymerization, especially those obtained with ytterbium triflate. On increasing the proportion of initiator the degradability was also increased.     

Syntheses of conductive adhesives based on epoxy resin and polyanilines by using N‐tert‐butyl‐5‐methylisoxazolium perchlorate as a thermally latent curing reagent

Conductive composites consisted of epoxy resin and polyanilines (PANIs) doped with dodecylbenzenesulfonic acid ( 1 ), dodecylsulfonic acid (2), di(2‐ethylhexyl)sulfosuccinic acid (3), and HCl were synthesized by use of N‐tert‐butyl‐5‐methylisoxazolium perchlorate (5) under various reaction conditions. It was found that the composites with PANI doped with acid 2 (PANI‐2) prepared by curing with 10 mol % of reagent 5 at 80 °C for 12 h showed high electroconductivity along with the low conducting percolation threshold (3 wt % of PANI‐2). Furthermore, the composite with even ?10 wt % of PANI‐2 exhibited ?10^?1 S/cm of electroconductivity. The UV–vis and IR measurements indicated that the conductive emeraldine salt form of PANI‐2 in the composite was maintained after the curing reaction. The thermal stability was studied by TGA and DSC measurements, and then, the T_d10 and T_g of the composite with 5 and 10 wt % of PANI‐2 were found to be similar to those with the cured epoxy resin itself. In addition, the similar investigation with an oxetane resin instead of the epoxy resin was also carried out. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 718–726, 2006     

Copolymerization of diglycidyl ether of bisphenol A with γ‐butyrolactone catalyzed by ytterbium triflate: Shrinkage during curing

Diglycidyl ether of bisphenol A (DGEBA) was cured with γ‐butyrolactone (γ‐BL) with ytterbium triflate as a catalyst. The curing was studied with differential scanning calorimetry, Fourier transform infrared (FTIR), and thermomechanical analysis. FTIR studies confirmed that four elemental reactions took place during the curing process: the formation of a spiroorthoester (SOE) by the reaction of DGEBA with γ‐BL, the homopolymerization of SOE, the homopolymerization of DGEBA, and the copolymerization of SOE and DGEBA. Moderate proportions of γ‐BL produced materials with higher glass‐transition temperatures, and the curing occurred with lower shrinkage after gelation because of the polymerization of SOE, with near‐zero shrinkage during the final stages of the curing. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2794–2808, 2003     

Synthesis and characterization of poly(dimethylsiloxane‐urethane) elastomers: Effect of hard segments of polyurethane on morphological and mechanical properties

A series of poly(dimethylsiloxane‐urethane) elastomers based on hexamethylenediisocyanate, toluenediisocyanate, or 4,4′‐methylenediphenyldiisocyanate hard segment and polydimethylsiloxane (PDMS) soft segment were synthesized. In this study, a new type of soft‐segmented PDMS crosslinker was synthesized by hydrosilylation reaction of 2‐allyloxyethanol with polyhydromethylsiloxane, using Karstedt's catalyst. The synthesized soft‐segmented crosslinker was characterized by FT‐IR, ¹H, and ¹³C NMR spectroscopic techniques. The mechanical and thermal properties of elastomers were characterized using tensile testing, thermogravimetric analysis, differential scanning calorimetry (DSC), and dynamical mechanical analysis measurements. The molecular structure of poly(dimethylsiloxane‐urethane) membranes was characterized by ATR‐FTIR spectroscopic techniques. Infrared spectra indicated the formation of urethane/urea aggregates and hydrogen bonding between the hard and soft domains. Better mechanical and thermal properties of the elastomers were observed. The restriction of chain mobility has been shown by the formation of hydrogen bonding in the soft and hard segment domains, resulting in the increase in the glass‐transition temperature of soft segments. DSC analysis indicates the phase separation of the hard and soft domains. The storage modulus (E′) of the elastomers was increasing with increase in the number of urethane connections between the hard and soft segments. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2980–2989, 2006     

Studies on curing kinetics of a novel combined liquid crystalline epoxy containing tetramethylbiphenyl and aromatic ester‐type mesogenic group with diaminodiphenylsulfone

The curing kinetics of a novel liquid crystalline epoxy resin with combining biphenyl and aromatic ester‐type mesogenic unit, diglycidyl ether of 4,4′‐bis(4‐hydroxybenzoyloxy)‐3,3′,5,5′‐tetramethyl biphenyl (DGE‐BHBTMBP), and the curing agent diaminodiphenylsulfone (DDS) was studied using the advanced isoconvensional method (AICM). DGE‐BHBTMBP/DDS curing system was investigated the curing behavior by means of differential scanning calorimetry (DSC) during isothermal and nonisothermal processes. Only one exothermal peak appeared in isothermal DSC curves. A variation of the effective activation energy with the extent of conversion was obtained by AICM. Three different curing stages were confirmed. In the initial curing stage, the value of E_a is dramatically decreased from ～90 to ～20 kJ/mol in the conversion region 0–0.2 for the formation of LC phase. In the middle stage, the value of E_a keeps about ～80 kJ/mol for cooperative effect of reaction mechanism and diffusion control. In the final stage, a significant increase of E_a from 84 to 136 kJ/mol could be caused by the mobility of longer polymer chains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3922–3928, 2007     

Study of hydrogen bonding and thermal properties of polybenzoxazine and poly‐(ε‐caprolactone) blends

The thermal properties of physical blends containing benzoxazine monomer and polycaprolactone (PCL) were monitored by DSC and Fourier transform infrared spectroscopy (FTIR). The ring‐opening reaction and subsequent polymerization reaction of the benzoxazine were facilitated significantly by the presence of a PCL modifier. Hydrogen‐bond formation between the hydroxyl groups of polybenzoxazine and the carbonyl groups of PCL was evident from the FTIR spectra. Only one glass‐transition temperture (T_g) value was found in the composition range investigated, and the T_g value of the resulting blend appeared to be higher in the blend with a greater amount of PCL. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 736–749, 2001     

Effects of different acid functional groups on proton conductivity of polymer‐1,2,4‐triazole blends

Proton transfer reactions under anhydrous conditions have attracted remarkable interest due to chemical energy conversions in polymer electrolyte membrane fuel cells. In this work, 1H‐1,2,4‐triazole (Tri) was used as a proton solvent in different polymer host matrices such as Poly(vinylphosphonic acid) (PVPA), and poly(2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid) (PAMPS). PVPATri_x and PAMPSTri_x electrolytes were investigated where x is the molar ratio of Tri to corresponding polymer repeat unit. The interaction between polymer and Tri was studied via FTIR spectroscopy. Thermogravimetry analysis and differential scanning calorimetry were employed to examine the thermal stability and homogeneity of the materials, respectively. PVPATri_1.5 showed a maximum water‐free proton conductivity of 2.3 × 10^?3 S/cm at 120 °C and that of PAMPSTri₂ was 9.3 × 10^?4 S/cm at 140 °C. The results were interpreted in terms of different acidic functional groups and composition. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3315–3322, 2006