Effects of temperature and anion species on CO2 permeability and CO2/N2 separation coefficient through ionic liquid membranes

The permeability of carbon dioxide (CO₂) through imidazolium-based ionic liquid membranes was measured by a sweep gas method. Six species of ionic liquids were studied in this work as follows: [emim][BF₄], [bmim][BF₄], [bmim][PF₆], [bmim][Tf₂N], [bmim][OTf], and [bmim][dca]. The ionic liquids were supported with a polyvinylidene fluoride porous membrane. The measurements were performed at T = (303.15 to 343.15) K. The partial pressure difference between feed and permeate sides was 0.121 MPa. The permeability of the CO₂ increases with temperature for the all ionic liquid species. Base on solution diffusion theory, it can be explained that the diffusion coefficient of CO₂ in an ionic liquid affects the temperature dependence more strongly than the solubility coefficient. The greatest permeability was obtained with the [bmim][Tf₂N] membrane. The membrane of [bmim][PF₆] presents the lowest permeability.The separation coefficient between CO₂ and N₂ through the ionic liquid membranes was also investigated at the volume fraction of CO₂ at feed side 0.10. The separation coefficient decreases with the increase of temperature for the all ionic liquid species. The membrane of [emim][BF₄] and [bmim][BF₄] gives the highest separation coefficient at constant temperature. The lowest separation coefficient was obtained from [bmim][Tf₂N] membrane which presents the highest permeability of CO₂.     

Cationic ring-opening polymerization of 3,3-bis（chloromethyl）oxacyclobutane in ionic liquids

Cationic ring-opening polymerization of 3,3-bis(chloromethyl)oxacyclobutane catalyzed by BF_3·OEt_2 was carried out in ionic liquids [bmim]BF_4 and [bmim]PF_6.The influences of BCMO concentration and molar ratio of BCMO/BF_3·OEt_2 on the molecular weights and yield of PBCMO were investigated.The polymerization in ionic liquids proceed to high conversions,although molecular weights are limited,similar to polymerization in organic solvent such as CH_2Cl_2.Follow a viewpoint of green chemistry, we feel ionic liquid [bmim]BF_4 is superior to [bmim]PF_6.Extracting [bmim]PF_6 from the product using organic solvent as extractant limits its advantage as a green reaction media.     

离子液体型表面活性剂研究

以1-甲基咪唑为原料, 制备了6个常规离子液体: 1-正丁基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[bmim][BF₄]及[bmim][PF₆])、1-正己基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[hmim][BF₄]及[hmim][PF₆])、1-正十六烷基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[C₁₆mim][BF₄]及[C₁₆mim][PF₆])和4个功能化离子液体: 1-(2-羟乙基)-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[2-hemim][BF₄]及[2-hemim][PF₆])、1-乙氧羰基甲基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[eocmmim][BF₄]及[eocmmim][PF₆]). 研究了这两类离子液体的一些物理性能, 旨在挖掘离子液体在香料香精化妆品工业中的应用价值. 分别检测了它们与一般溶剂的互溶性, 并测定了它们的表面张力和发泡性能, 实验结果表明, 仅[C₁₆mim][BF₄]和[C₁₆mim][PF₆]具有发泡性能, 发泡力分别为68和120 mm.     

1,3-Cycloaddition of nitrile oxides in ionic liquids. An easier route to 3-carboxy isoxazolines, potential constrained glutamic acid analogues

Several improvements in the cycloaddition of carboethoxyformonitrile oxide (CEFNO) with different alkenes are observed in the ionic liquids [bmim][BF₄] and [bmim][PF₆]. The possibility of obtaining good yields of the corresponding isoxazolines opens the way towards parallel collections of glutamic acid (Glu) analogues.     

Bicyclic imidazolium-based ionic liquids: synthesis and characterization

We previously reported the use of imidazole as starting compound for preparing a bicyclic imidazolium ionic liquid, [b-3C-im][NTf₂], with an overall 29% isolated yield in four synthetic steps. This new room temperature ionic liquid was shown to be far more chemically stable than commonly used [bmim][PF₆], [bdmim][PF₆], and [bdmim][NTf₂]. Because of this intriguing chemical stability, it prompted us to develop a more generalized and high yielding synthesis so that molecular diversity of bicyclic ionic liquids may be explored. In this work, we amended the previous synthetic route by employing 4-chlorobutyronitrile or 5-chlorovaleronitrile as starting materials and successfully developed a five-step synthesis of a series of novel bicyclic imidazolium-based ionic liquids in 40-53% overall isolated yields. We investigated intrinsic reactivity of all bicyclic ionic liquids prepared and found that, under strongly basic conditions, among all tested ionic liquids the 5,5-membered [R-3C-im][NTf₂] ionic liquids were most stable to solvent deuterium isotope exchange while the previously reported [bdmim][NTf₂] ionic liquid was 50% deuterium exchanged at its C-2 methyl in 30 min at ambient temperature. Under identical condition, the commonly used [bmim][NTf₂] ionic liquid was deuterium exchanged instantaneously at its C-2 hydrogen. In the absence of bases, only [bmim][PF₆] was deuterium exchanged (50% within 1 h) and all other ionic liquids gave no detectable exchanges even after 25 days at ambient temperature. Moreover, both [bmim][NTf₂] and [bdmim][NTf₂] ionic liquids were readily methylated at C-2 position with methyl iodide under basic condition at room temperature. Under the same condition, [R-3C-im][NTf₂] and [R-4C-im][NTf₂] ionic liquids were completely stable and chemically inert. We envisioned that [R-3C-im][NTf₂] should be well suited as solvents for organic synthesis.     

1-Butyl-2,3-trimethyleneimidazolium bis(trifluoromethylsulfonyl)imide ([b-3C-im][NTf2]): a new, stable ionic liquid

Using imidazole as the starting material, the synthesis of a new bicyclic ionic liquid [b-3C-im][NTf₂] is described. Except for the alkylation reaction in the second step (40% yield) of this four-step synthesis of [b-3C-im][NTf₂], others were all high yielding reactions (85-94% isolated yields). We investigated intrinsic reactivity of this and other imidazolium-based ionic liquids and found that, under strongly basic conditions (KOD in CD₃OD/D₂O (1:1) solution), the new ionic liquid was stable to solvent deuterium isotope exchange while the previously reported [bdmim][NTf₂] and [bdmim][PF₆] ionic liquids were 50% deuterium exchanged at its C-2 methyl in 30 min at ambient temperature. At the same experimental condition, the most commonly employed [bmim][PF₆] ionic liquid was deuterium exchanged instantaneously at its C-2 hydrogen. In the absence of bases (CD₃OD/D₂O = 1:1), only [bmim][PF₆] was deuterium exchanged (50% within 1 h) and other ionic liquids gave no detectable exchanges even after one week at ambient temperature. It is therefore concluded that the new [b-3C-im][NTf₂] ionic liquid is far more chemically stable than previously reported [bmim][PF₆], [bdmim][NTf₂], and [bdmim][PF₆].     

Evaluation and comparison of global scalar properties for the simultaneous interaction of ionic liquids with thiophene and pyridine

Ab initio studies were carried out with mixtures containing ionic liquid with thiophene and pyridine for studying the simultaneous interaction. Global scalar properties such as HOMO/LUMO energies, HOMO–LUMO energy gap, chemical hardness, chemical potential, electronegativity, global hardness, global softness and electrophilicity index were determined for clusters containing ionic liquids with thiophene and pyridine. Ionic liquids containing: 1-butyl-3-methylpyrrolidinium [BUMPYR], 1-benzyl-3-methyimidazolioum [BeMIM] and 1-butyl-3-methylpyridinium [BUMPY] cations combined with inorganic anions containing fluorine ([BF₄] and [PF₆]) were studied in this work. [BeMIM][BF₄] (1-benzyl-3-methyimidazolioum tetrafluoroborate) with a HOMO–LUMO energy gap of 0.1882 Hartrees was found to be the most effective IL. Further a ranking based on all the mentioned scalar parameters also pointed out [BeMIM][BF₄] to be the most desirable IL. The overall ranking after taking into considerations all factors followed: [BeMIM][BF₄] > [BUMPYR][BF₄] > [BUMPY][PF₆] > [BUMPY][BF₄] > [BUMPYR][PF₆]. To validate the findings, infinite dilution activity coefficients were predicted using the quantum chemical based COSMO-RS methodology which gave the same trend as observed using scalar properties.     

Chemoselective reduction of aromatic nitro and azo compounds in ionic liquids using zinc and ammonium salts

Nitroarenes were chemoselectively reduced to the corresponding amines using zinc and aqueous ammonium salts in ionic liquids as a safe and recyclable reaction medium. Our results specify the effect of ammonium salts in the process; the combination of Zn/NH₄Cl in [bmim][PF₆] or Zn/HCO₂NH₄ in [bmim][BF₄] were the suitable conditions for the reduction of nitroarenes. Azobenzenes were also smoothly reduced to hydrazobenzenes with Zn/HCO₂NH₄ (aq.) in recyclable [bmim][BF₄] without any over reduction to the corresponding anilines.     

Amine basicity: measurements of ion pair stability in ionic liquid media

The stability constants relevant to the formation of amine/p-nitrophenol ion pairs have been determined in [bmim][BF₄] solution, in the presence of butylamine, piperidine, and triethylamine, by using spectrophotometric measurements. In order to evaluate how the ion pair stability is affected by ionic liquid structure, piperidine has been chosen as model amine for studies in [bmim][PF₆], [bmim][NTf₂], [bm₂im][NTf₂] and in several [bmim][BF₄]/1,4-dioxane binary mixtures. Data obtained in ionic liquid solutions have been compared with those previously reported in conventional organic solvents.     

Solubility of CO2 in imidazolium-based tetrafluoroborate ionic liquids

The solubility of CO₂ in imidazolium ionic liquids (ILs), 1-butyl-3-methyl imidazolium tetrafluoroborate ([bmim][BF₄]), 1-hexyl-3-methyl imidazolium tetrafluoroborate ([hmim][BF₄]) and 1-octyl-3-methyl imidazolium tetrtafluoroborate ([omim][BF₄]) was determined at 305-25 K and pressures from 1 to 9 MPa. The influence of chain length of alkyl substituents on the imidazolium cation on the solubility of CO₂ was investigated. The differences in solubility with chain length are in the sequence [omim][BF₄] > [hmim][BF₄] > [bmim][BF₄]. The solubility data were correlated by the extended Henry's law, and enthalpy, Gibbs free energy and entropy changes were obtained.     

Homogeneous catalytic aminocarbonylation of iodoalkenes and iodobenzene with amino acid esters under conventional conditions and in ionic liquids

Amino acid methyl esters were used as amine nucleophiles in palladium catalysed aminocarbonylation of iodobenzene and iodoalkenes (1-iodo-cyclohexene and 17-iodo-androst-16-ene). 2-Oxo-carboxamide type derivatives can be isolated as a result of double CO insertion by using iodobenzene as a substrate at elevated carbon monoxide pressure. On the contrary, carboxamides of expected structure were obtained exclusively in excellent yields in the whole pressure range by using iodoalkenes. The aminocarbonylation of 17-iodo-androst-16-ene in [bmim][PF₆] or [bmim][BF₄] (where bmim=1-butyl-3-methyl-imidazolium cation) ionic liquids was also carried out and the ionic liquid-catalyst mixtures have been reused several times with only a small loss of activity.     

Solubility of H2S in ionic liquids [hmim][PF6], [hmim][BF4], and [hmim][Tf2N]

The solubility of hydrogen sulphide in three ionic liquids, viz. 1-hexyl-3-methylilmidazolium hexafluorophosphate ([hmim][PF₆]), 1-hexyl-3-methylimidazolium tetrafluoroborate ([hmim][BF₄]), and 1-hexyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([hmim][Tf₂N]), at temperatures ranging from 303.15 K to 343.15 K and pressures up to 1.1 MPa were determined. The solubility values were correlated using the Krichevsky–Kasarnovsky equation and Henry’s constants were obtained at different temperatures. Partial molar thermodynamic functions of solvation such as standard Gibbs free energy, enthalpy, and entropy were calculated from the solubility results. Comparison of the values obtained show that the solubility of H₂S in these three ionic liquids was in the sequence: [hmim][BF₄] > [hmim][PF₆] ≈ [hmim][Tf₂N].     

Synthesis of fused tetrahydro-β-carbolinequinoxalinones in 1-n-butyl-2,3-dimethylimidazolium bis(trifluoromethylsulfonyl)imide ([bdmim][Tf2N]) and 1-n-butyl-2,3-dimethylimidazolium perfluorobutylsulfonate ([bdmim][PFBuSO3]) ionic liquids

Starting from tryptophan methyl ester, a three-step synthesis of fused tetrahydro-β-carbolinequinoxalinones in two new ionic liquids, [bdmim][Tf₂N] and [bdmim][PFBuSO₃], was described. Both ionic liquids can be readily prepared from commercially available starting materials in high yields. Unlike the commonly used [PF₆]-based ionic liquids that evidently undergo slow hydrolysis of the PF₆ anion with the concomitant release of HF, ionic liquids of [bdmim][Tf₂N] and [bdmim][PFBuSO₃] are not only chemically stable but also apparently inert to hydrolysis and therefore organic reactions carried out in both ionic liquids proceed smoothly with good yields. The overall isolated yields for this three-step synthesis of tetrahydro-β-carbolinequinoxalinones were 34-55%. To the best of our knowledge, the preparation of fused tetrahydro-β-carbolinequinoxalinones was unprecedented.     

Imidazolium ionic liquids with short polyoxyethylene chains

It has been observed by us earlier that imidazolium ionic liquids ([bmim][BF₄] react with paraformaldehyde giving in nearly quantitative yield imidazolium ionic liquids substituted at 2‐position with hydroxymethyl group ([bhmim][BF₄]). In this article, we describe the application of those ionic liquids (after converting hydroxyl group into alkoxide anion by reaction with sodium hydride) as initiators for anionic polymerization of ethylene oxide (EO). Up to DP_n ～ 30 polymerization proceeds without side reactions, and the product is exclusively low‐molecular‐weight polyoxyethylene containing imidazolium head group (POE‐IL) with DP_n equal to [EO]/[bhmim] ratio. By increasing [EO]/[bhmim] ratio further, side reaction start to interfere, and macromolecules that does not contain imidazolium head groups are also formed, as evidenced by analysis of MALDI TOF spectra. Blending of POE‐IL with high‐molecular‐weight POE leads to significant reduction of crystallinity of POE. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6961–6968, 2008     

Solvent relaxation of a room-temperature ionic liquid [bmim][PF6] confined in a ternary microemulsion

In this paper we have reported the solvent and rotational relaxation of 1-butyl-3-methyl-imidazolium hexafluorophosphate ([bmim][PF₆]) confined in tween 20/([bmim][PF₆]/water microemulsion using coumarin 153 (C-153) as probe. The most interesting feature of our experiment was that we observed an increase in solvent relaxation time with increase in R (R = tween 20-to-[bmim][PF₆] molar ratio). This is due to the fact that with increase in [bmim][PF₆] content of the microemulsions, the microviscosity of the pool of the microemulsions increases, and motion of ions of [bmim][PF₆] is hindered in the pool of microemulsions. Since motion of ions is responsible for solvation in room-temperature ionic liquids (RTILs), solvent-relaxation time increases with increase in R.     

Preparation of Nylon-6 Particles in Ionic Liquids

Summary: Utilizing the thermal stability of ionic liquid, micrometer-sized Nylon-6 particles were successfully prepared by hydrolytic polymerization of ε-caprolactam at high temperature with polyvinyl pyrrolidone as stabilizer in ionic liquids, 1-butyl-3-methyl imidazolium tetrafluoroborate, [Bmim][BF₄] and N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium bis(trifluoro-methanesulfonyl)amide, [DEME][TFSA]. The obtained particles had a unique shape because Nylon-6 is a crystalline polymer. Viscosity-average molecular weights of Nylon-6 prepared in [Bmim][BF₄] and [DEME][TFSA] at 180 °C for 48 h were 4200 and 2200, respectively.     

Acceleration of the Baylis–Hillman Reaction in the Presence of Ionic Liquids

The Baylis–Hillman reaction is accelerated in the presence of ionic liquids. Of various 1‐butyl‐3‐methylimidazolium (bmim)‐based ionic liquids tested, [bmim][PF₆] has been found to result in the highest rate increase. In the company of Lewis acid and H‐bond‐donor additives, the reaction rates further improve, albeit only modestly. A preparatively useful Baylis–Hillman procedure prescribes the use of [bmim][PF₆] with La(OTf)₃ and 2,2′2″‐nitrilotris[ethanol], in which the net effect of the ionic liquid is to bring about a more than twofold rate increase over the otherwise same reaction in MeCN.     

Extraction and high performance liquid chromatographic determination of 3-indole butyric acid in pea plants by using imidazolium-based ionic liquids as extractant

In this paper, imidazolium-based ionic liquids [C₄mim][PF₆], [C₆mim][PF₆], [C₈mim][PF₆], [C₆mim][BF₄] and [C₈mim][BF₄] were tested as extracting solvents for removal of 3-indole butyric acid (IBA) from aqueous media with subsequent determination using HPLC. Percent extraction of IBA was strongly affected by pH of aqueous phases and the chemical structures of ionic liquids (ILs). Extraction of IBA was quantitative in the pH values lower than pK_a of IBA. Considering both extraction and stripping efficiencies of IBA, [C₄mim][PF₆] was found to act more efficient than other studied ILs. Capacity of [C₄mim][PF₆] was 17.6 × 10⁻⁴ mmol IBA per 1.0 mL of IL. Ionic strength of aqueous phase and temperature had shown no serious effects on extraction efficiency of IBA. A preconcentration factor of 100 and a relative standard deviation of 1.16% were obtained. It was found that ionic liquid phase was reusable almost five times for extraction/stripping purposes. 3-Indole acetic acid showed interferential effect in the extraction step. In order to assess the applicability of the method, extraction and stripping of IBA from pea plants and some other samples were studied.     

Influence of ionic liquids on the phase transfer-catalysed enantioselective Michael reaction

The enantioselective Michael addition of dimethyl malonate to 1,3-diphenylprop-2-en-1-one promoted by a quaternary derived ammonium salt from quinine as a phase transfer catalyst in different ionic liquids, 1-butyl-3-methyl imidazolium hexafluorophosphate, [bmim]PF₆, 1-butyl-3-methyl pyridinium tetrafluoroborate, [bpy]BF₄, 1-butyl-3-methyl imidazolium tetrafluoroborate [bmim]BF₄ as well as in conventional organic solvents was studied.     

Cationic Polymerization of 3‐Ethyl‐3‐hydroxymethyloxetane in an Ionic Liquid

Summary: Cationic ring‐opening polymerization of 3‐ethyl‐3‐hydroxymethyloxetane (EOX) in a neutral ionic liquid (1‐butyl‐3‐methylimidazolium tetrafluoroborate, [bmim][BF₄]) leading to a multihydroxyl, branched polyether proceeds readily to nearly quantitative conversion. Because of the relatively high polarity of ionic liquids, intermolecular hydrogen bonding leading to the formation of aggregates is reduced considerably. On the other hand, intramolecular hydrogen bonding facilitating intramolecular chain transfer is not significantly affected and the molecular weights of polymers are in the same range as those obtained in bulk polymerization or polymerization in organic solvents.