Simultaneous measurement of strain and temperature with a long-period fiber grating inscribed Sagnac interferometer

A Sagnac interferometer with a long-period fiber grating (LPG) inscribed in the polarization-maintaining fiber (PMF) is proposed and experimentally demonstrated for simultaneous measurement of strain and temperature. Due to the different responses of the LPG and the Sagnac interferometer to strain and temperature, simultaneous measurement can be achieved by monitoring the wavelength shifts and the intensity changes of a resonance dip of the sensor setup. The experimental results show that the achieved sensitivities to strain and temperature are 6.4 × 10^− 3 dB/με and 0.65 nm/°C, respectively.     

White light interferometry test and analysis of LiNbO3 polarizer

White light interferometer can be used to measure the amplitude extinction ratio (ER) of polarizer and coupling distribution in fiber. A LiNbO₃ polarizer coupled with a polarization maintaining fiber and a silica planar waveguide at the two ends was measured using white light interferometer. According to the principles of optical coherence domain polarimeter (OCDP) technique, the test scheme is analyzed and presented to measure the ER of LiNbO₃ polarizer with its apparatus proposed correspondingly. By analyzing the interference intensity, both the ER of LiNbO₃ polarizer and its coupling crosstalk with optical fiber and waveguide are obtained. The results illustrate that the ER of a 5 mm-long LiNbO₃ polarizer is 71 dB and the crosstalk of the coupling points are around 40 dB. The results have good agreement with analysis.     

Temperature-insensitive strain measurement using a birefringent interferometer based on a polarization-maintaining photonic crystal fiber

We propose a novel and simple scheme for a temperature-insensitive strain measurement by using a birefringent interferometer configured by a polarization-maintaining photonic crystal fiber (PM-PCF). The wavelength-dependent periodic transmission in a birefringent interferometer can be achieved by using a PM-PCF between two linear polarizers. Since the PM-PCF is composed of a single material, such as silica, the peak wavelength shift with temperature variation can be negligible because of the small amount of the birefringence change of the PM-PCF with temperature change. The measured temperature sensitivity is −0.3 pm/°C. However, the peak wavelength can be changed by strain because the peak wavelength shift is directly proportion to strain change. The strain sensitivity is measured to be 1.3 pm/με in a strain range from 0 to 1600 με. The measurement resolution of the strain is estimated to be 2.1 με. The proposed scheme has advantages of simple structure and low loss without a Sagnac loop, temperature insensitivity, ease installation, and short length of a sensing probe compared with a conventional PMF-based Sagnac loop interferometer.     

Switchable dual-wavelength erbium-doped fiber-ring laser based on one polarization maintaining fiber Bragg grating in a Sagnac loop interferometer

A switchable erbium-doped fiber-ring laser providing dual-wavelength outputs with orthogonal polarizations when operating at room temperature is proposed. One polarization-maintaining fiber Bragg grating (PMFBG) in a Sagnac loop interferometer is used as the wavelength-selective filter. Due to the enhancement of the polarization hole burning (PHB) by the PMFBG, the laser can be designed to operate in stable dual-wavelength or wavelength-switching modes with a wavelength spacing of 0.336 nm at room temperature by adjusting a polarization controller (PC). The optical signal-to-noise ratio (OSNR) is over 42 dB. The amplitude variation over 90 min is less than 0.6 dB for both wavelengths.     

Broad tunability of erbium-doped fiber ring laser based on few-mode polarization maintaining fiber Sagnac interferometer

A highly stable erbium-doped fiber (EDF) ring laser with broad tunability is proposed and experimentally demonstrated. It is accomplished by using a few-mode polarization maintaining fiber (FM-PMF) Sagnac interferometer, in which simultaneous Sagnac and modal interferences occur. Continuously tunable output is obtained by exerting the longitudinal strain on the FM-PMF in combination with adjusting a polarization controller (PC) next to the FM-PMF in the Sagnac interferometer. In addition, the adverse impact of uneven EDF gain distribution on the laser output power uniformity may be offset by the PC-dependent transmission loss of the FM-PMF Sagnac interferometer and reflected backward C-band amplifier spontaneous emission from the pumped EDF. During the whole tuning process, the tunable span covers more than 40 nm with the output power flatness better than 1 dB, 3 dB spectral linewidth narrower than 0.1 nm and optical signal-to-noise extinction ratio higher than 45 dB.     

Tunable dual-wavelength fiber laser based on a single fiber Bragg grating in a Sagnac loop interferometer

We propose a simple dual-wavelength Er-doped fiber laser configuration based on a dual-wavelength fiber Bragg grating written on the splice joint between two different fibers for wavelength-selective filter in the Sagnac loop interferometer. The wavelength separation between the adjacent lasing wavelengths is 1.12 nm and the side-mode suppression ratio (SMSR) is over 55 dB. The output power variation is less than 0.8 dB over a two-minute period. Moreover, the lasing wavelength can be effectively tuned using the thermal heating method.     

Curvature measurement by using low-birefringence photonic crystal fiber based Sagnac loop

An optical fiber curvature sensor with low-birefringence photonic crystal fiber (PCF) based Sagnac loop is demonstrated experimentally. The low-birefringence PCF of about 40 cm long is inserted into Sagnac loop, and a section of it about 155 mm is used as the sensing element. The Sagnac output spectra under different curvatures are measured and analyzed. The results show that the wavelength shift of the transmission dip has a linear relationship with the curvature. The sensitivity of the curvature measurement of − 0.337 nm is achieved in the range of 0-9.92 m^− 1. And the temperature effect of the proposed sensor is also analyzed.     

A tunable and switchable single-longitudinal-mode dual-wavelength fiber laser incorporating a reconfigurable dual-pass Mach-Zehnder interferometer and its application in microwave generation

A tunable and switchable single-longitudinal-mode (SLM) dual-wavelength fiber laser incorporating a reconfigurable dual-pass Mach-Zehnder interferometer (MZI) filter was proposed and demonstrated, which can be applied in microwave generation. By incorporating a high extinction ratio (ER) dual-pass MZI into an erbium-doped fiber ring cavity, SLM dual-wavelength lasing can be achieved even using a MZI with relatively little free spectrum range (FSR), and by beating the two wavelengths at a photodetector, a 9.76 GHz microwave signal with a 3-dB bandwidth of less than 10 kHz is obtained. Moreover, by direct linking the two outputs of the MZI, the high ER dual-pass MZI is easily reconfigured as a half FSR dual-pass MZI. Using this structure, switchable SLM dual-wavelength lasing can be conveniently realized.     

Modified super-wide-angle Sagnac imaging interferometer based on LCoS for atmospheric wind measurement

The modified super-wide-angle Sagnac imaging interferometer (MSASII) based on liquid crystals on silicon (LCoS) is proposed as a novel device for the detection of the upper atmospheric wind field. This device employs the phase-only modulation (POM) of LCoS coupled with the MSASII, and can measure phase changes in multi-band emissions without moving mirror. It can be used to replace the conventional Michelson’s interferometer with step-moving mirror device. The optical path difference (OPD) equation of MSASII-LCoS is derived, and the four compensation conditions (field, chromatics, thermal and achromaticity of thermal compensations) are discussed within the scope of wind measurement. The real parameters of LCoS and optical glasses are selected for numerical simulation and analysis. Three aurora lines (732.0, 630.0 and 557.7 nm) are considered, and their phase variations are 3.61, 2.02 and 0.15 fringes at the same incident angle of 3°, respectively. The rate of change of OPD with temperature is the magnitude of 10⁻⁶ cm/K, and the corresponding phase variations are within 0.09 fringes. The accuracy of phase modulation can be 0.614×10⁻² rad when LCoS of 10-bits is used. The novel model MSASII-LCoS shows its advantage for atmospheric wind measurement in the aspects of the overall structure, anti-vibration, operational flexibility and detection accuracy.     

Magneto-optic fiber Sagnac modulator based on magnetic fluids

A magneto-optic modulator with a magnetic fluid film inserted into an optical fiber Sagnac interferometer is proposed. The magnetic fluid exhibits variable birefringence and Faraday effect under external magnetic field that will lead to a phase difference and polarization state rotation in the Sagnac interferometer. As a result, the intensity of the output light is modulated under the external magnetic field. Moreover, the modulator has a high extinction ratio and can easily be integrated in a single-mode fiber system. The performance of the modulator is not affected by ambient temperature variation from room temperature to 40 °C.     

Switchable multi-wavelength erbium-doped fiber ring laser based on cascaded polarization maintaining fiber Bragg gratings in a Sagnac loop interferometer

A switchable multi-wavelength erbium-doped fiber (EDF) ring laser based on cascaded polarization maintaining fiber Bragg gratings (PMFBGs) in a Sagnac loop interferometer as the wavelength-selective filter at room temperature is proposed. Due to the polarization hole burning (PHB) enhanced by the PMFBGs, stable single-, dual-, three- and four-wavelength lasing operations can be obtained. The laser can be switched among the stable single-, dual-, three- and four-wavelength lasing operations by adjusting the polarization controllers (PCs). The optical signal-to-noise ratio (OSNR) is over 50 dB.     

Ultrafast all-optical XOR logic gate based on a symmetrical Mach-Zehnder interferometer employing SOI waveguides

We present an integrated Silicon-on-Insulator (SOI) based Mach-Zehnder interferometer (MZI) in order to perform ultrafast all-optical XOR logic gate operation with a bit rate of ∼ 0.33 Tb/s. A numerical simulation is carried out in order to study various parameters such as extinction ratio and eye-opening parameters, characterizing the performance of the XOR logic gate. The output XOR logic gate signal can have improved extinction and eye margin if the initial powers of primary signals and the probe continuous-wave (CW), and SOI waveguide length are judiciously adjusted.     

Fiber optic Fabry-Perot pressure sensor with low sensitivity to temperature changes for downhole application

Pressure and temperature are two important parameters in reservoir engineering. The fiber optic sensors can be used for permanent downhole monitoring. In this paper, we propose an extrinsic fiber Fabry-Perot interferometer (EFPI) sensor for pressure measurement with low sensitivity variation. The pressure sensitivity of EFPI sensor and of the fiber Bragg grating (FBG) sensors have been measured. The experimental pressure sensitivity for EFPI and FBG sensors are measured to be 2.75 × 10⁻⁸ 1/kPa and 1.52 × 10⁻⁸ 1/kPa, respectively. The temperature cross-sensitivity problem of the EFPI sensor has been solved by a new technique. The temperature sensitivity of EFPI sensor has been decreased to 1.2 × 10⁻⁶/°C, while the temperature sensitivity of non-compensated EFPI sensor has been measured to be 16.4 × 10⁻⁶/°C. The results show that the EFPI sensor has a higher pressure sensitivity and good capability to decrease temperature sensitivity in comparison to FBG sensor.     

Switchable erbium-doped fiber ring laser based on Sagnac loop mirror incorporating few-mode high birefringence fiber

Without the need of any other additional filtering device, a triple-wavelength switchable erbium-doped fiber ring laser based on Sagnac loop mirror incorporating a piece of few-mode high birefringence fiber is newly proposed and experimentally demonstrated. Three potential lasing wavelengths at about 2.0 nm interval with the side mode suppression ratio higher than 40 dB can be switched mainly by adjusting a polarization controller next to the few-mode high birefringence fiber in the Sagnac loop. In addition to the stable single-line lasing operation, simultaneous dual- and triple-line oscillations are also highly stable at room temperature with suppressing the intrinsic homogeneous gain broadening of the erbium-doped fiber.     

Real-time surface profile measurement using a feedback type of sinusoidal phase modulating interferometer

In this paper, we propose a sinusoidal phase modulating (SPM) interferometer that is insensitive to external disturbances, and its measuring principle is analyzed theoretically. In the SPM interferometer, the interference signal is detected by a high-speed image sensor based on a low-speed CCD and a signal processing circuit is used to obtain the phase of each point on the surface. Therefore, the surface profile can be measured real-time. The experiments measuring the surface profile of a wedge-shaped optical flat show that the measurement time of the SPM interferometer is less than 10 ms, the repetitive measurement accuracy is 4.2 nm. The results show that the impacts of nonlinear distortion of the piezoelectric transducer (PZT) and part external disturbance are removed.     

基于侧漏型光子晶体光纤高灵敏度宽线性范围弯曲传感器的研究

基于所研制的侧漏型光子晶体光纤, 提出并研制出一种Sagnac干涉仪型高灵敏度宽线性测量范围的弯曲传感器. 实验研究结果表明, 当侧漏型光子晶体光纤中的线性缺陷与弯曲方向一致时, 采用群双折射和波谷波长偏移量测量弯曲曲率均可获得高的弯曲灵敏度, 但线性测量范围小, 且不能进行小弯曲曲率的测量. 当线性缺陷与弯曲方向垂直时, 以波谷波长偏移量进行弯曲曲率检测, 可获得10.798 nm/m^-1高灵敏度的同时且可实现0–5.03 m^-1的宽线性测量范围, 结合测量矩阵的引入可实现温度和弯曲曲率的同时测量, 进而剔除环境温度变化对弯曲曲率检测的干扰, 实现了高灵敏度宽线性范围的弯曲传感; 而以群双折射进行弯曲曲率检测, 虽然检测灵敏度较低, 但可实现对环境温度不敏感的弯曲传感. 关键词： 弯曲传感器 侧漏型光子晶体光纤 高灵敏度 宽线性范围     

Designs of all-optical NOR gates using SOA based MZI

The paper investigates the non-linear behavior of semiconductor optical amplifier with Mach–Zehnder interferometer (SOA-MZI) configuration which makes it to work as a logic gate. The two designs of NOR gate based on SOA-MZI have been verified. The basic principal of both designs are same. The summation of data pulses have been taken and inverted to perform a NOR operation. In the design, the first 3 dB coupler creates a phase difference of π/2 in clock pulse and data pulse while passing through two interferometer arms. The clock and data pulses pass through SOA which attenuates the clock pulse wherever the data pulse is present. After passing through second 3 dB coupler a phase difference of π/2 is again created. Therefore, if the clock pulse is in the same phase will be added and if it is out of phase, will be canceled. The designs have been investigated at different bit-rates to achieve higher extinction ratio (ER), Q-factor and bit-error rate (BER) for different pump currents of SOA.     

Hybrid Mach-Zehnder interferometer and knot resonator based on silica microfibers

We propose and demonstrate an all-fiber high Q Mach-Zehnder interferometer (MZI)-coupled microknot resonator (MZKR) structure using optical microfibers drawn from silica fibers. The experimental results show that this microfiber-based structure achieved a high Q factor of ∼ 15,000 and good interference fringes with extinction ratio of up to ∼ 15 dB. By optimizing the loop-length of the microfiber knot and the optical path-difference of the MZI, the desired MZKR with higher Q factor and better extinction ratio could be obtained. A series of integrated all-fiber optical devices could be realized based on such a MZKR structure due to its outstanding advantages of easy fabrication, great flexibility, low cost, low loss, etc.     

Instantaneous frequency measurement based on complementary microwave photonic filters with a shared Mach-Zehnder interferometer

A novel configuration using only one Mach-Zehnder interferometer (MZI) for photonic-assisted instantaneous microwave frequency measurement is proposed. The amplitude comparison function (ACF), related to the input microwave frequency while independent of the input optical power and modulate index, is achieved by using a ratio of low-pass to bandpass frequency responses introduced by intensity and phase modulation with a shared MZI. The microwave frequency can be estimated by the measured ACF. A proof-of-concept experiment for measurement of RF from 5 to 10 GHz is successfully demonstrated with the measurement errors less than ± 0.2 GHz.     

Full L-band coverage of multiwavelength erbium-doped fiber laser

We propose and experimentally demonstrate a dual-pass unbalanced in-line Sagnac interferometer as a novel comb filter for implements in erbium-doped fiber lasers to obtain wide wavebands of multiwavelength radiations with enhancements of signal-to-noise ratios (SNRs). The hybrid combinations of the comb filter with the two schemes of nonlinear polarization rotation and intensity dependent loss have successfully not only enlarged the lasing bandwidth up to 47 nm but also enhanced the SNR up to 40 dB. The simultaneous lasing-wavelengths of 117 channels are also obtained. The multiwavelength lasing spectra with free spectral range of 0.4 nm covering the full L-band are useful for the applications of DWDM and WDM-PON systems.