Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

Low temperature synthesis of nanosized ZnNb<Subscript>2</Subscript>O<Subscript>6</Subscript> photocatalysts by a citrate complex method

Nanosized ZnNb₂O₆ photocatalysts (band gaps ~4.0 eV) were successfully synthesized via a citrate complex method. Their particle sizes ranged from 50 to 150 nm. The result of Mott–Schottky measurement revealed that the flat-band potential of ZnNb₂O₆ was ca. −1.3 V versus Ag/AgCl at pH 6.6. The photocatalytic activities of the samples for the degradation of methyl orange were evaluated under UV-light (λ = 254 nm). It was found that the sample obtained at 850 °C showed the highest photocatalytic activity due to its opportune crystallinity and surface area. Furthermore, ·OH radicals were detected as the major oxidation agents responsible for the decomposition of methyl orange.     

Optical,magnetic and photocatalytic properties of magnetically separable Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>-doped ZnO and pristine ZnO nanospheres

This work focussed on the optical, magnetic and photocatalytic properties of sol–gel-synthesized Fe₃O₄-doped ZnO nanospheres and was compared with pristine ZnO nanospheres. The crystalline phase of Fe₃O₄-doped ZnO nanospheres was studied with X-ray diffraction analysis and was well matched with standard pattern. Surface morphology was studied with HR-SEM images and EDAX spectrum. Furthermore, elemental mapping analysis was carried out to confirm the presence of Fe₃O₄ phase in Fe₃O₄-doped ZnO nanospheres. FT-Raman spectral studies show that a strong intense peak at 670 cm^?1 indicates the presence of Fe₃O₄ in Fe₃O₄-doped ZnO nanospheres. The mean crystallite size of Fe₃O₄-doped ZnO nanospheres was 34 nm as calculated by Debye–Scherrer’s formula which confirmed with HR-TEM image. The SAED pattern shows the presence of (100), (101), (102) and (202) of ZnO phase and (400) of Fe₃O₄ phase, confirming the crystalline nature of Fe₃O₄-doped ZnO nanospheres. The vibrating sample magnetometer (VSM) result shows that Fe₃O₄-doped ZnO nanospheres possess superparamagnetic nature and the composite nanospheres are magnetically separable. The optical properties have been studied by diffuse reflectance spectroscopy and time-resolved photoluminescence spectra. Implantation of Fe₃O₄ in ZnO nanospheres modifies the UV absorption edge, and it displays near-band gap emission and deep-level emission. The photocatalytic activity of Fe₃O₄-doped ZnO nanospheres studied against rhodamine B dye is found higher than that of pristine ZnO nanospheres which shows that Fe₃O₄-doped ZnO nanospheres are a promising photocatalyst.     

Preparation of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by mechanical alloying and annealing for sensitizing C-modified TiO<Subscript>2</Subscript> and acquirement of efficient photocatalyst

ZnFe₂O₄ nanoparticles sensitized by C-modified TiO₂ hybrids (ZnFe₂O₄–TiO₂/C) were successfully prepared by a feasible method. The ZnFe₂O₄ nanoparticles were prepared by mechanical alloying and annealing. The residual organic compounds in the synthetic process of TiO₂ were selected as the carbon source. The as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, transmission electron microscopy, X-ray photoelectron spectroscopy, ultraviolet–visible light diffuse reflectance spectroscopy (UV–Vis) and N₂ adsorption–desorption analysis. The photocatalytic activity of the photocatalysts was measured by degradation of methyl orange under ultraviolet (UV) light and simulated solar irradiation, respectively. The results show that the carbon did not enter the TiO₂ lattice but adhered to the surface of TiO₂. The photocatalytic activity of the as-prepared C-modified TiO₂ (TiO₂/C) improved both under UV and simulated solar light irradiation, but the improvement was not dramatic. Introduction of ZnFe₂O₄ into the TiO₂/C could enhance the absorption spectrum range. The ZnFe₂O₄–TiO₂/C hybrids exhibited a higher photocatalytic activity both than that of the pure TiO₂ and TiO₂/C under either UV or simulated solar light irradiation. The complex synergistic effect plays an important role in improving the photocatalytic performance of ZnFe₂O₄–TiO₂/C composites. The optimum photocatalytic performance was obtained from the ZnFe₂O₄(0.8 wt%)–TiO₂/C sample.     

Synthesis and Characterization of the Superparamagnetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Ag Nanocomposites

The study of superparamagnetic Fe₃O₄/Ag nanocomposites have received great research attention due to their wide range of potential applications in biomedicine. In this report, an easy microemulsion reaction was employed to synthesis Fe₃O₄/Ag nanocomposites with self-aggregated branch like nanostructures. The Fe₃O₄ nanoparticles were initially prepared and subsequently AgNO₃ was reduced as Ag by chemical reduction method. The results showed that the average size of the Fe₃O₄/Ag nanocomposites were in the range of 10 ± 2 nm. These nanoparticles were self-aggregated as a branch like nanostructure. The optical properties of Fe₃O₄ nanoparticles were modified with surface plasmon resonance of Ag nanoparticles. The observed saturation magnetization of superparamagnetic Fe₃O₄/Ag nanocomposites were 40 emu/g.     

Facile ultrasonic-assisted preparation of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Ag<Subscript>3</Subscript>VO<Subscript>4</Subscript> nanocomposites as magnetically recoverable visible-light-driven photocatalysts with considerable activity

In this work, a facile ultrasonic-assisted method was applied for preparation of Fe₃O₄/Ag₃VO₄ nanocomposites with different compositions. The as-prepared products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive analysis of X-rays, UV–Vis diffuse reflectance spectroscopy, Fourier transform infrared spectroscopy, and vibrating sample magnetometery. Photocatalytic degradation of rhodamine B under visible-light irradiation was investigated, and it was found that weight ratio of Fe₃O₄–Ag₃VO₄ has significant influence on the photocatalytic activity and the nanocomposite with 1:4 weight ratio of Fe₃O₄–Ag₃VO₄ has superior activity. In addition, the nanocomposite showed great activities in degradations of methylene blue and fuchsine, which are comparable with activity of the pure Ag₃VO₄. More importantly, this nanocomposite displayed remarkable saturation magnetization, leading to easily and quickly separation of its suspension from treated system by applying a magnetic field.     

Novel Visible-Light-Driven Photocatalyst Co<Subscript>3</Subscript>O<Subscript>4</Subscript>/FeWO<Subscript>4</Subscript> for Efficient Decomposition of Organic Pollutants

A highly efficient and visible light (λ ≥ 420 nm) responsive composite photocatalyst, Co₃O₄/FeWO₄ was prepared by simple impregnation method. The heterojunction semiconductors Co₃O₄/FeWO₄ demonstrated notably high photocatalytic activity over a wide range of composition than the individual component Co₃O₄ or FeWO₄ for the complete degradation of 1,4-dichlorobenzene (DCB) in aqueous phase under visible light irradiation. The photocatalytic activity of composite was optimized at 1/99 Co₃O₄/FeWO₄ composition. After 2 h of visible light irradiation 51% decomposition of 1,4-dichlorobenzene (DCB) was observed utilizing 1/99 Co₃O₄/FeWO₄ photocatalyst while the end members demonstrated a negligible degradation under the same experimental condition. The valence band (VB) and conduction band (CB) of Co₃O₄ is located above the VB and CB of FeWO₄, respectively. Both the semiconductors Co₃O₄ and FeWO₄ exhibit strong absorption over the wide range of visible light. The obviously enhanced photocatalytic performance of Co₃O₄/FeWO₄ composite has been discussed on the hole (h⁺) as well as electron (e^?) transfer mechanism between the VB and CB of individual semiconductors.     

One-dimensional porous Ag/AgBr/TiO<Subscript>2</Subscript> nanofibres with enhanced visible light photocatalytic activity

One-dimensional (1D) Ag/AgBr/TiO₂ nanofibres (NFs) have been successfully fabricated by the one-pot electrospinning method. In comparison with bare TiO₂ NFs and Ag/AgBr/PVP (polyvinylpyrrolidone) NFs, the 1D Ag/AgBr/TiO₂ NFs photocatalyst exhibits much higher photocatalytic activity in the degradation of a commonly used dye, methylene blue (MB), under visible light. The photocatalytic removal efficiency of MB over Ag/AgBr/TiO₂ NFs achieves almost 100 % in 20 min. The photocatalytic reaction follows the first-order kinetics and the rate constant (k) for the degradation of MB by Ag/AgBr/TiO₂ NFs is 5.2 times and 6.6 times that of Ag/AgBr/PVP NFs and TiO₂ NFs, respectively. The enhanced photocatalytic activity is ascribed to the stronger visible light absorption, more effective separation of photogenerated electron-hole pairs, and faster charge transfer in the long nanofibrous structure. The Ag/AgBr/TiO₂ NFs maintain a highly stable photocatalytic activity due to its good structural stability and the self-stability system of Ag/AgBr. The mechanisms for photocatalysis associated with Ag/AgBr/TiO₂ NFs are proposed. The degradation of MB in the presence of scavengers reveals that h⁺ and ^?O ₂ ^? significantly contribute to the degradation of MB.     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.     

Nonstoichiometric Zn Ferrite and ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Composite Spheres: Preparation,Magnetic Properties,and Chromium Removal

Monodisperse and porous nonstoichiometric Zn ferrite can be prepared by a solvothermal method. Such non-Zn ferrite was used to be the precursor for synthesis of ZnFe₂O₄/Fe₂O₃ composite via calcination at 600°C for 3 h in air. X-ray powder diffractometer (XRD) and Energy Dispersive Spectrometer (EDS) proved the nonstoichiometry of Zn ferrite synthesized by solvothermal method and the formation of ZnFe₂O₄/Fe₂O₃ composite via calcination. TEM image showed that non-Zn ferrite spheres with wormlike nanopore structure were made of primary nanocrystals. BET surface area of non-Zn ferrite was much higher than that of ZnFe₂O₄/Fe₂O₃ composite. Saturation magnetization of non-Zn ferrites was significantly higher than that of ZnFe₂O₄/Fe₂O₃ composites. Calcination of non-Zn ferrite resulted in the formation of large amount of non-magnetic Fe₂O₃,which caused a low magnetization of composite. Because of higher BET surface area and higher saturation magnetization, non-Zn ferrite presented better Cr⁶⁺ adsorption property than ZnFe₂O₄/Fe₂O₃ composites.     

Green synthesis and characterization of Ag and Ag/Fe3O4 nanocomposites for antimicrobial effect and rhodamine- B dye degradation

We used a simple two-stage tactic to design and synthesize a magnetically separable catalyst (MSC) Ag/Fe₃O₄ by combining independently synthesized Fe₃O₄ and Jatropha curcas root functionalized Ag nanoparticles (NPs) at room temperature. The phase composition of Ag/Fe₃O₄ NCs was revealed by morphological and structural assessment. The derived Ag/Fe₃O₄ nanocomposites demonstrated outstanding antimicrobial activity against Gram-negative Pseudomonas aeruginosa comparing to Gram-positive Bacillus subtilis which was determined by the agar well diffusion method. This is due to positively charged surface of metal oxide NPs that may bind to cell membrane. Interestingly, Ag–Fe₃O₄ NCs demonstrated good photocatalytic activity for organic dye degradation. According to a kinetic study, Ag/Fe₃O₄ MSC removed 99% of Rhodamine B at a rate constant of 1.89 min^?1. The photoelectron could perhaps ultimately collide only with dissolved solids in the substrate to form superoxides, which can damage the dye. Notably, the MSCs reusability was tested using magnetic detachment without sacrificing photocatalytic efficiency. This finding represents a significant breakthrough in the domain of wastewater treatment and biomedicine.     

Photocatalysis enhancement of CaAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>, Nd<Superscript>3+</Superscript>@TiO<Subscript>2</Subscript> composite powders

CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were synthesized by a sol–gel method under mild conditions (i.e. low temperature and ambient pressure). The as-prepared powders were characterized by transmission electron microscopy (TEM) and analyzed by X-ray diffraction (XRD). The photocatalytic behavior of the TiO₂-base surfaces was evaluated by the degradation of nitrogen monoxide gas. It suggested that CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were composed of anatase titania and that CaAl₂O₄:Eu²⁺, Nd³⁺. TiO₂ particles were deposited on the surface of CaAl₂O₄:Eu²⁺, Nd³⁺ to form uniform film. CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders exhibited higher photocatalytic activity compared with pure TiO₂ under visible light. And the result also clearly indicated that the long afterglow phosphor absorbed and stored lights for the TiO₂ to remain photocatalytic activity in the dark.     

Fabrication of noble-metal-free NiS<Subscript>2</Subscript>/g-C<Subscript>3</Subscript>N<Subscript>4</Subscript> hybrid photocatalysts with visible light-responsive photocatalytic activities

Nanocomposites of NiS₂ with graphitic carbon nitride (NiS₂/g-C₃N₄) have been successfully synthesized by means of a facile hydrothermal method. The photocatalytic activities of as-prepared samples were evaluated by monitoring the photodecomposition of rhodamine B under visible light irradiation. The experimental results indicated that visible light-driven NiS₂/g-C₃N₄ composites exhibited an enhanced photocatalytic activity compared to that of pure NiS₂, due to the fast generation, separation and transportation of the photogenerated carriers resulting from the addition of NiS₂ nanoparticles (NPs). Interestingly, different amounts of NiS₂ deposition can affect the photocatalytic activities of the NiS₂/g-C₃N₄ composites. A suitable loading amount of NiS₂ NPs presents the best photodegradation performance. The photocatalytic reaction mechanism for the improved photocatalytic performance of NiS₂/g-C₃N₄ catalyst was proposed which was supported by PL, PEC, EIS and active species trapping results. A promising strategy presented here provides a facile route towards the development of economical, noble metal-free composites as photocatalysts for the applications in environmental remediation.     

Enhancement of thermoelectric performance of Na<Subscript>x</Subscript>Co<Subscript>2</Subscript>O<Subscript>4</Subscript> with Ag dispersion by precipitation from Ag<Superscript>+</Superscript> aqueous solution

Thermoelectric Na_xCo₂O₄/Ag composites were synthesized by citric acid complex (CAC) method and Ag precipitation from CH₃COOAg aqueous solution on the Na_xCo₂O₄ powders. Effects of the synthesis process on microstructure and thermoelectric performance of Na_xCo₂O₄/Ag composites were investigated. When the Na_xCo₂O₄ CAC powders were dipped in CH₃COOAg aqueous solution and dried, fine Ag particles less than around 300 nm in size were precipitated on the surface of Na_xCo₂O₄ powders. After the subsequent sintering process, the flaky Ag phase, the length and thickness of which were up to 5 and 1 μm, respectively, existed along interfaces between Na_xCo₂O₄ grains. The sizes of Ag particles obtained in this study were found to be smaller than those of the conventionally prepared Na_xCo₂O₄/Ag composites. The fine dispersion of Ag grains was effective for suppressing the increase in thermal conductivity due to the addition of metallic phase, Ag, and for improving the thermoelectric performance of Na_xCo₂O₄/Ag composites, suggesting that the synthesis technique composed of the CAC method and Ag precipitation from CH₃COOAg aqueous solution is significantly important process for thermoelectric Na_xCo₂O₄/Ag composites.     

Adsorption behavior of <Superscript>99</Superscript>Tc on Fe,Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>

Summary The adsorption of ⁹⁹Tc on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ was studied by batch experiments under aerobic and anoxic conditions. The effects of pH and CO₃^2- concentration of the simulated ground water on the adsorption ratios were also investigated, and the valences of Tc in solution after the adsorption equilibrium were studied by solvent extraction. The adsorption isotherms of TcO₄- on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ were determined. Experimental results have shown that the adsorption ratio of Tc on Fe decreases with the increase of pH in the range of 5-12 and increases with the decrease of the CO₃^2- concentration in the range of 10^-8M-10^-2M. Under aerobic conditions, the adsorption ratios of ⁹⁹Tc on Fe₂O₃ and Fe₃O₄ were not influenced by pH and CO₃^2-concentration. When Fe was used as adsorbent, Tc existed mainly in the form of Tc(IV) after equilibrium and in the form of Tc(VII) when the adsorbent was Fe₂O₃ or Fe₃O₄ under aerobic conditions. The adsorption ratios of Tc on Fe, Fe₂O₃ and Fe₃O₄ decreased with the increase of pH in the range of 5-12 and increased with the decrease of the CO₃^2- concentration in the range of 10^-8M-10^-2M under anoxic conditions. Tc existed mainly in the form of Tc(IV) after equilibrium when Fe, Fe₂O₃ and Fe₃O₄ was the adsorbent under anoxic conditions. The adsorption isotherms of TcO_4- on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ are fairly in agreement with the Freundlich’s equation under both aerobic and anoxic conditions.     

Effective photocatalytic degradation of an azo dye over nanosized Ag/AgBr-modified TiO<Subscript>2</Subscript> loaded on zeolite

Zeolite-based photocatalysts were prepared by the sol-gel and deposition methods. The photocatalysts were characterised by X-ray diffraction, nitrogen adsorption-desorption isotherms, FTIR spectroscopy, scanning electron microscopy and energy-dispersive X-ray spectrometry. The activity of the prepared photocatalysts was evaluated by the UV-induced degradation of acid blue 92, a textile dye in common use. The effect of various parameters, such as catalyst concentration, initial dye concentration, thiosulphate concentration and pH, on the rate and efficiency of the photocatalytic degradation of acid blue 92 was investigated. The results showed that each parameter influenced the degradation rate and efficiency in a particular way. It was also found that, under optimised conditions, Ag/AgBr/TiO₂/zeolite exhibited the highest photocatalytic performance. A comparison of catalytic activity when exposed to visible light under the same conditions showed that the photocatalysts containing AgBr had the highest activity.     

Photocatalytic degradation of organic dyes by Er<Superscript>3+</Superscript>: YAlO<Subscript>3</Subscript>/Co- and Fe-doped ZnO coated composites under solar irradiation

In this work, the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites were prepared by the sol-gel method. Then, they were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy (EDX). Photo-degradation of azo fuchsine (AF) as a model dye under solar light irradiation was studied to evaluate the photocatalytic activity of the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites. It was found that the photocatalytic activity of Co- and Fe-doped ZnO composites can be obviously enhanced by upconversion luminescence agent (Er³⁺: YAlO₃). Besides, the photocatalytic activity of Er³⁺: YAlO₃/Fe-doped ZnO is better than that of Er³⁺: YAlO₃/Co-doped ZnO. The influence of experiment conditions, such as the concentration of Er³⁺: YAlO₃, heat-treatment temperature and time on the photocatalytic activity of the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites was studied. In addition, the effects of solar light irradiation time, dye initial concentration, Er³⁺: YAlO₃/Co- and Fe-doped ZnO amount on the photocatalytic degradation of azo fuchsine in aqueous solution were investigated in detail. Simultaneously, some other organic dyes, such as Methyl Orange (MO), Rhodamine B (RM-B), Acid Red B (AR-B), Congo Red (CR), and Methyl Blue (MB) were also studied. The possible excitation principle of Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites under solar light irradiation and the photocatalytic degradation mechanism of organic dyes were discussed.     

Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/BiFeO<Subscript>3</Subscript> heterostructure: preparation,characterization, and photocatalytic activity

Bi₂O₃/BiFeO₃ composite was successfully fabricated by a conventional sol–gel method and structural properties were characterized based on X-ray diffractometer, scanning electron microscope, transmission electron microscope, energy-dispersive X-ray analyzer, nitrogen adsorption–desorption measurement, and UV–visible diffuse reflectance spectroscopy. Bi₂O₃/BiFeO₃ had a good absorption for visible light, which was benefit to photocatalytic activity. The highest degradation efficiency was obtained when the content of Bi₂O₃ in Bi₂O₃/BiFeO₃ was 63.9%. Effect of experimental conditions was investigated, and the highest photocatalytic activity of Bi₂O₃/BiFeO₃ was observed at photocatalyst dosage of 0.5 g/L, initial BPA concentration of 10 mg/L, and solution pH of 6.3. Bi₂O₃/BiFeO₃ photocatalyst exhibited enhanced photocatalytic activity for BPA, and the reaction rate constant over Bi₂O₃/BiFeO₃ composite was 2.23, 3.65, and 8.71 times higher than that of BiFeO₃, Bi₂O₃ and commercial TiO₂ (P25), respectively. Bi₂O₃/BiFeO₃ showed high photocatalytic activity after three cycles, suggesting that it was a stable photocatalyst. The possible photocatalytic mechanism has been discussed on the basis of the theoretical calculation and the experimental results. The hydroxyl and superoxide radicals together with photogenerated holes played significant roles in the photocatalytic reaction.     

Statistical modeling of <Emphasis Type="Italic">p</Emphasis>-nitrophenol degradation using a response surface methodology (RSM) over nano zero-valent iron-modified Degussa P25-TiO<Subscript>2</Subscript>/ZnO photocatalyst with persulfate

Zero-valent iron-modified Degussa P25-TiO₂/ZnO nanocomposites (denoted as P25/Fe⁰/ZnO) were designed and prepared via Fe⁰ impregnation of P25-TiO₂/ZnO and then were employed in the visible-light photocatalytic degradation of p-nitrophenol (PNP) in the presence of [K₂S₂O₈]. Central composite design was applied for response surface modeling (RSM) to understand the influence of selected factors (pH, [Fe⁰] wt% and [K₂S₂O₈] concentration) on the degradation of PNP and to determine the interaction between the factors. The maximal PNP degradation efficiency (86.9%) was obtained with P25/1.5 wt% Fe⁰/ZnO at 3 mg/L of [K₂S₂O₈] concentration and pH 7.5. In addition, the RSM showed a satisfactory correlation between the experimental and predicted values of PNP degradation. The P25/Fe⁰/ZnO photocatalyst performance was also examined degrading methyl orange and phenol and high degradation efficiency, 82 and 99%, was achieved, respectively. The structure, morphology, light absorption and photocatalytic properties of as-prepared P25/Fe⁰/ZnO were studied using TEM, BET, XRD, FTIR and DRS.     

Hydrothermal synthesis of graphene-ZnTiO<Subscript>3</Subscript> nanocomposites with enhanced photocatalytic activities

Pure phase ZnTiO₃ was prepared through a sol–gel process, then graphene-ZnTiO₃ nanocomposites were synthesized by a hydrothermal method using the prepared ZnTiO₃ nanoparticles and graphene oxide as precursors. X-ray diffraction results revealed the production of pure cubic ZnTiO₃ at 600 °C. ZnTiO₃ was anchored on the graphene nanosheets, demonstrating a spherical morphology in transmission electron microscope images. The existence of chemical bond Ti–O–C in the nanocomposites was proved by Fourier-transforming infrared spectroscopy. UV–Vis diffusive reflection spectra indicated that the absorption edge of the nanocomposites shifted towards the visible region. The photocatalytic activity of the composites was tested through the photocatalytic degradation of methyl blue under simulated solar irradiation. The results showed that the photocatalytic activity of the nanocomposites was obviously increased in contrast to pure ZnTiO₃, which was strongly affected by the crystalline structure of ZnTiO₃ and the concentration of graphene. The enhanced photocatalytic activity was mainly attributed to the conglomeration inhibition of ZnTiO₃ nanoparticles, the electron transfer between ZnTiO₃ and graphene and the extended absorption range. Furthermore, other contaminants such as tetracycline, Rhodamine B and methyl orange were tested under the same conditions to investigate the photocatalytic performance of the photocatalysts. The reusability tests indicated that the prepared composites exhibited good stability.