Synthesis and characterization of a nanocomposite of goethite nanorods and reduced graphene oxide for electrochemical capacitors

We report a one-step synthesis of a nanocomposite of goethite (α-FeOOH) nanorods and reduced graphene oxide (RGO) using a solution method in which ferrous cations serve as a reducing agent of graphite oxide (GO) to graphene and a precursor to grow goethite nanorods. As-prepared goethite nanorods have an average length of 200 nm and a diameter of 30 nm and are densely attached on both sides of the RGO sheets. The electrochemical properties of the nanocomposite were characterized by cyclic voltammetry (CV) and chronopotentiometry (CP) charge–discharge tests. The results showed that goethite/RGO composites have a high electrochemical capacitance of 165.5 F g^?1 with an excellent recycling capability making the material promising for electrochemical capacitors.     

Influence of Al2O3/ Y-TSZ Mixture as Filler Loading on the Radiopacity of PMMA Denture Base Composites

The radiopacity of alumina/yttrium stabilizer zirconia (Al₂O₃/Y-TSZ) particles with nitrile butadiene rubber (NBR) dispersed in PMMA denture base material has been investigated. PMMA matrix without filler was prepared from PMMA powder with 0.5% benzoyl peroxide (PBO) as the control material. The similar PMMA matrix was mixed with Al₂O₃/Y-TSZ (1:1) together with NBR particles as the reinforcement. The amount of NBR was fixed at 7.5 wt %, however, Al₂O₃/Y-TSZ varied from 1 to 10 wt %, respectively. Samples with 4 mm thickness for each composition were irradiated using 60 KV, 10 mA, 0.4 s to examine their radiopacity. This radiopacity was compared to radiopacity of aluminum plate which having the same thickness. The result shows that the radiopacity (i.e. the lower optical density the higher radiopacity) of reinforced PMMA matrix slightly increased from 1.40 to 1.05, respectively, with the increased of filler loading compared to unreinforced PMMA matrix.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

Graphene oxide doped polyaniline for supercapacitors

A novel high-performance electrode material based on fibrillar polyaniline (PANI) doped with graphene oxide sheets was synthesized via in situ polymerization of monomer in the presence of graphene oxide, with a high conductivity of 10 S cm^?1 at 22 °C for the obtained nanocomposite with a mass ratio of aniline/graphite oxide, 100:1. Its high specific capacitance of 531 F/g was obtained in the potential range from 0 to 0.45 V at 200 mA/g by charge–discharge analysis compared to 216 F/g of individual PANI. The doping and the ratio of graphene oxide have a pronounced effect on the electrochemical capacitance performance of the nanocomposites.     

Graphene supported electrocatalysts for methanol oxidation

Graphene nanosheet was prepared by modified Hummer’s chemical method and utilized as a catalyst support of PtRu nanoparticles for the electro-oxidation of methanol. Home-made graphene nanosheet was clearly characterized by Raman spectroscopy and we applied colloidal method to synthesize with high metal content of 80 wt.% Pt–Ru catalyst, which is extensively clarified by HR-TEM and XRD analysis. 80 wt.% Pt–Ru/graphene nanosheet catalyst showed superior electrochemical activity toward methanol oxidation compared to Pt–Ru/Vulcan XC-72R. It is due to the significant increase of electrochemical active surface area for better catalyst utilization.     

Controlled synthesis of MnSn(OH)6/graphene nanocomposites and their electrochemical properties as capacitive materials

We report the synthesis of novel MnSn(OH)₆/graphene nanocomposites produced by a co-precipitation method and their potential application for electrochemical energy storage. The hydroxide decorated graphene nanocomposites display better performance over pure MnSn(OH)₆ nanoparticles because the graphene sheets act as conductive bridges improving the ionic and electronic transport. The crystallinity of MnSn(OH)₆ nanoparticles deposited on the surface of graphene sheets also impacts the capacitive properties as electrodes. The maximum capacitance of 31.2 F/g (59.4 F/g based on the mass of MnSn(OH)₆ nanoparticles) was achieved for the sample with a low degree of crystallinity. No significant degradation of capacitance occurred after 500 cycles at a current density of 1.5 A/g in 1 M Na₂SO₄ aqueous solution, indicating an excellent electrochemical stability. The results serve as an example demonstrating the potential of integrating highly conductive graphene networks into binary metal hydroxide in improving the performance of active electrode materials for electrochemical energy storage applications.     

Cocontinuous morphology of immiscible high density polyethylene/polyamide 6 blend induced by multiwalled carbon nanotubes network

The effect of functionalized multiwalled carbon nanotubes (FMWCNTs) on the phase morphology of immiscible high density polyethylene/polyamide 6 (HDPE/PA6, 50/50) blend has been investigated. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to study both the morphology variation of the nanocomposites and the selective distribution of FMWCNTs in the nanocomposites. It is clear that adding small amount of FMWCNTs (<2.0 wt.%) does not exert profound influence on the sea-island morphology of the nanocomposites. However, at moderate content of FMWCNTs (2.0 and 5.0 wt.%), a typical cocontinuous morphology is detected. Further increasing FMWCNTs content (10.0 wt.%) induces phase inversion. The crystallization behaviors of both HDPE and PA6 components were investigated by using differential scanning calorimetry (DSC) and wide angle X-ray diffraction (WAXD). The results show the apparent nucleation effect of FMWCNTs for PA6 crystallization due to the selective distribution of FMWCNTs in PA6 phase. Rheological measurements exhibit the presence of FMWCNTs network structure in the nanocomposites. It is suggested that the formation of the cocontinuous morphology and the novel crystallization behaviors of PA6 at high content of FMWCNTs are ascribed to the formation of the FMWCNTs network structure.     

Dielectric properties of onion-like carbon based polymer films: Experiment and modeling

Dielectric analysis of a novel polymer composite based on onion-like carbon (OLC) has been carried out by varying the temperature between 240 and 460 K within a wide frequency range (20 Hz–1 MHz). A small effect of the OLC inclusions on the beta transition of OLC/polymethylmethacrylate (PMMA) composite has been observed, which indicates a weak affinity of the OLC to the host matrix. At the same time, an increase in concentration of the OLC has been found to strongly influence the glass and melting temperatures of the nanocomposites. These structural properties of the OLC/PMMA composite materials should be taken into account when a new family of effective wide-band electromagnetic materials are designed and fabricated.     

Application of Potassium Carbonate as Space Holder for Metal Injection Molding Process of Open Pore Copper Foam

Copper foam has recently being applied to replace aluminium as heat sink. In this study, copper foam was manufactured via metal injection molding technique. Copper feedstock were prepared comprising 0 wt.%, 30 wt.% and 40 wt.% of potassium carbonate into copper powder to produce open pore cell structure, which also mixed together with a binder system consisting palm stearin (PS), polyethylene (PE) and stearic acid (SA). The feedstock was then injection molded into tensile shape test piece prior to solvent extracted in heptane prior to sintering using tube furnace at 850^oC for 4 hours in nitrogen atmosphere. The sintered samples were immersed in warm water to dissolve the carbonates. Copper foam has successfully manufactured at 850^oC for 4 hours in nitrogen atmosphere followed by the dissolution process. The porosity value increased as the addition of potassium carbonate increased from 0 to 40 wt.% which given the highest value of 52.985% porosity and thermal conductivity of 520.46 W/m.K.     

Synthesis of waterborne acrylic/clay nanocomposites by controlled surface initiation from macroinitiator modified montmorillonite

The nitroxide mediated controlled surface initiated polymerization of methyl methacrylate (MMA)/butyl acrylate (n-BA) was carried out with a macroinitiator modified montmorillonite. The macroinitiator was synthesized by the nitroxide mediated polymerization of vinylbenzyl trimethylammonium chloride (VBTMACl), methylmethacrylate (MMA) and styrene (S) at 90 °C using BlocBuilder®. The macroinitiator was exchanged with the sodium cations of the montmorillonite, to yield surface modified reactive montmorillonite. The bulk polymerizations of BA/MMA from the clay surface produced controlled molecular weight polymers that were able to exfoliate the clay. This controlled polymer/clay nanocomposite was used as masterbatch and further dispersed in monomers and miniemulsified to perform miniemulsion polymerization of BA/MMA (90/10 wt.%) at 30 wt.% solids content at low emulsifier concentration. The adhesive properties of the nanocomposites prepared with the masterbatch were proved to be better than those prepared with an organically modified clay.     

Application of Raman spectroscopy to study of the polymer foams modified in the volume and on the surface by carbon nanotubes

Polylactide nanocomposites with multi-walled carbon nanotubes (PLA/MWCNT) in the form of porous foams made of a biocompatible, biodegradable and environmentally friendly polymer with a small amount of carbon nanotubes, were investigated in this work. Additionally, PLA/MWCNT porous nanocomposites were coated with MWCNTs using the electrophoretic deposition method (EPD). All samples were characterized by a porosity of about 90%, showing pore sizes in the range of 100 to 200 μm, for PLA/MWCNT foam, however, EPD deposition resulted in an decrease in the number of smaller pores in PLA/MWCNT + MWCNT (EPD) foam. The porous polymer (PLA) matrix, shows almost twofold increase in crystallinity while depth penetrating the volume of the sample. The crystallinity, of the PLA/MWCNT foam, at first is growing then it gradually lowers, while for the PLA/MWCNT + MWCNT(EPD) foam almost does not change. This behavior points toward significant distinction between surface and interior of the samples. A detailed analysis of Raman spectra indicates related carbon structures occurring in the nanomaterial foams: graphene and graphite phases, CNT and also carbon amorphous phases. The characteristics of a single-shell vibration are visible by the character of the G-band. The estimated crystallite size in PLA/MWCNT + MWCNT(EPD) is about 3 times smaller than that in the PLA/MWCNT.     

Graphene prepared by one-pot solvent exfoliation as a highly sensitive platform for electrochemical sensing

Graphene was easily obtained via one-step ultrasonic exfoliation of graphite powder in N-methyl-2-pyrrolidone. Scanning electron microscopy, transmission electron microscopy, Raman and particle size measurements indicated that the exfoliation efficiency and the amount of produced graphene increased with ultrasonic time. The electrochemical properties and analytical applications of the resulting graphene were systematically studied. Compared with the predominantly-used reduced graphene oxides, the obtained graphene by one-step solvent exfoliation greatly enhanced the oxidation signals of various analytes, such as ascorbic acid (AA), dopamine (DA), uric acid (UA), xanthine (XA), hypoxanthine (HXA), bisphenol A (BPA), ponceau 4R, and sunset yellow. The detection limits of AA, DA, UA, XA, HXA, BPA, ponceau 4R, and sunset yellow were evaluated to be 0.8 μM, 7.5 nM, 2.5 nM, 4 nM, 10 nM, 20 nM, 2 nM, and 1 nM, which are much lower than the reported values. Thus, the prepared graphene via solvent exfoliation strategy displays strong signal amplification ability and holds great promise in constructing a universal and sensitive electrochemical sensing platform.     

Fabrication of super-macroporous nanocomposites by deposition of carbon nanotubes onto polymer cryogels

Electrically conducting super-macroporous carbon nanotube/polymer cryogel nanocomposites were fabricated by a novel approach based on deposition of carbon nanotubes (CNTs) onto the inner surface of pre-formed cryogels assisted by cryogenic treatment. Stable aqueous dispersions of multi-walled and single-walled carbon nanotubes were firstly obtained by non-covalent modification of pristine nanotubes with either pyrene containing polydimethylacrylamide or poly(ethylene oxide)₂₆-b-poly(propylene oxide)₄₀-b-poly(ethylene oxide)₂₆ copolymers and, then, exploited for the preparation of nanocomposites. The mechanical and electrical properties of nanocomposite materials were measured and compared to similar materials prepared by established method. The novel approach provided super-macroporous nanocomposites with high electrical conductivity (>10^?2 S/m) at much lower nanotube content (0.12 wt.%).     

Evaluation of Schiff bases of 2,5-dimercapto-1,3,4-thiadiazole as photostabilizer for poly(methyl methacrylate)

The photostabilization of poly(methyl methacrylate) (PMMA) films by Schiff bases of 2,5-dimercapto-1,3,4-thiadiazole compounds was investigated. The PMMA films containing concentration of complexes 0.5% by weight were produced by the casting method from chloroform solvent. The photostabilization activities of these compounds were determined by monitoring the hydroxyl index with irradiation time. The changes in viscosity average molecular weight of PMMA with irradiation time were also tracked (using benzene as a solvent). The quantum yield of the chain scission (Φ_cs) of these complexes in PMMA films was evaluated and found to range between 4.19 × 10^?5 and 8.75 × 10^?5. Results obtained showed that the rate of photostabilization of PMMA in the presence of the additive followed the trend:[1] > [2] > [3] > [4] > [5].According to the experimental results obtained, several mechanisms were suggested depending on the structure of the additive. Among them, UV absorption, peroxide decomposer, and radical scavenger for photostabilizer mechanisms were suggested.     

On the stability and properties of the polyacrylate/Na-MMT nanocomposite obtained by seeded emulsion polymerization

For high performance waterborne coatings usually polymer latexes with low emulsifier content are more preferred. Although polymer/clay nanocomposites offer improved properties, it is difficult to produce clay based nanocomposite latexes containing low emulsifier due to the stabilization problems especially caused by organoclays. Present study deals with the preparation of a tBA/BA/MAA ternary copolymer/clay nanocomposite containing 3 wt.% sodium montmorillonite (Na⁺-MMT) via seeded emulsion polymerization. Experimentally it was observed that even the usage of hydrophilic clay caused stabilization problem and a certain amount of emulsifier (>1 wt.%) was necessary to obtain stable latexes. In addition, the usage of a low molecular weight water soluble polymer as steric barrier was found to increase the stability of system. Obtained nanocomposite latex showed fine particle size diameter (127 nm) and very narrow size distribution (PDI = 0.06). The WAXD and TEM investigations indicated that a mostly exfoliated nanocomposite was obtained. Thermal analyses (DSC, DMTA and TGA) showed that there was no change at T_g of the copolymer while very high improvement was obtained for elastic modulus and a slight increase in thermal stability. According to the rheological measurements, the nanocomposite latex showed a higher low shear viscosity, a stronger shear thinning behavior and an improved physical stability in comparison to the reference latex.     

Enhanced reversible lithium storage in a nanosize silicon/graphene composite

Si/graphene composite was prepared by simply mixing of commercially available nanosize Si and graphene. Electrochemical tests show that the Si/graphene composite maintains a capacity of 1168 mAh g^?1 and an average coulombic efficiency of 93% up to 30 cycles. EIS indicates that the Si/graphene composite electrode has less than 50% of the charge-transfer resistance compared with nanosize Si electrode, evidencing the enhanced ionic conductivity of Si/graphene composite. The enhanced cycling stability is attributed to the fact that the Si/graphene composite can accommodate large volume charge of Si and maintain good electronic contact.     

Dual-doped graphene/perovskite bifunctional catalysts and the oxygen reduction reaction

We report the first investigation of dual-doped graphene/perovskite mixtures as catalysts for oxygen reduction. Pairwise combinations of boron, nitrogen, phosphorus and sulfur precursors were co-reduced with graphene oxide and mixed with La_0.8Sr_0.2MnO₃ (LSM) to produce SN-Gr/LSM, PN-Gr/LSM and BN-Gr/LSM catalysts. In addition, the dual-doped graphenes, graphene, LSM, and commercial Pt/C were used as controls. The addition of LSM to the dual-doped graphenes significantly improved their catalytic performance, with optimised composition ratios enabling PN-Gr/LSM to achieve 85% of the current density of commercial Pt/C at − 0.6 V (vs. Ag/AgCl) at the same loading. The effective number of electrons increased to ca. 3.8, and kinetic analysis confirms the direct 4 electron pathway is favoured over the stepwise (2e + 2e) route: the rate of peroxide production was also found to be lowered by the addition of LSM to less than 10%.     

Mechanoelectrochemical synthesis of porous Ti-based nanocomposite biomaterials

In this work we have synthesized a new class of nanocomposites based on Ti with the addition of hydroxyapatite (HA) and glass 45S5. The nanocomposites were prepared by mechanical alloying of the pure microcrystalline Ti powders with different amount of ceramics. The powder mixture was milled up to 48 h, pressed and sintered, which resulted in nanocomposite structure with the grain size of about 20–36 nm. The ultra low grain size structure improves mechanical properties of the implants in comparison to commonly used microcrystalline Ti-based implants. For example, the hardness of the Ti-HA nanocomposites reaches a value of 1500 HV and is five times greater than the microcrystalline Ti.To improve bonding of the implants with human tissue, the implants were electrochemically etched in 1 M H₃PO₄ + 2–10% HF electrolyte at 10 V vs. OCP for times up to 60 min. The treatment results in highly porous surface covered with Ti-oxide. The nanocrystalline structure is very useful during etching, due to the easy access of the electrolyte to the large volume of the grain boundaries. The nanocomposites with modified surface show very good corrosion resistance in Ringer’s solution.     

Effect of hydrogen-sulfide on the hydrogen permeance of palladium–copper alloys at elevated temperatures

The hydrogen permeance of several 0.1 mm thick Pd–Cu alloy foils (80 wt.% Pd–20 wt.% Cu, 60 wt.% Pd–40 wt.% Cu and 53 wt.% Pd–47 wt.% Cu) was evaluated using transient flux measurements at temperatures ranging from 603 to 1123 K and pressures up to 620 kPa both in the presence and absence of 1000 ppm H₂S. Sulfur resistance, as evidenced by no significant change in permeance, was correlated with the temperatures associated with the face-centered-cubic crystalline structure for the alloys in this study. The permeance of the body-centered cubic phase, however, was up to two orders of magnitude lower when exposed to H₂S. A smooth transition from sulfur poisoning to sulfur resistance with increasing temperature was correlated with the alloy transition from a body-centered-cubic structure to a face-centered-cubic structure.     

Gamma-ray response of a clear,crosslinked PMMA dosimeter,Radix W

Radix W, a clear poly(methyl-methacrylate) (PMMA) dosimeter was developed with improved properties compared to the conventional clear PMMA dosimeter, Radix RN15. PMMA with a glass transition temperature (T_g) higher than 120 °C was selected making it possible to measure doses in a wide range of 1 to 150 kGy. Dose rates of 2.5–10 kGy/h were tested and did not affect significantly the dose response. The influence of irradiation temperature was reduced compared with Radix RN15.