Enzymatic surface modification of Kevlar fibers

Horseradish peroxidase catalyzed grafting of acrylamide (AM) onto Kevlar fibers has been studied. The modified fiber has been characterized with scanning electron microscopy (SEM), elemental analysis and the grafting yield. From the SEM micrographs, the surface of the grafted Kevlar fiber is rougher than that of the untreated fiber, and the elemental analysis indicated that the nitrogen content of the treated fibers is higher than that of the untreated fiber. All the results suggested that AM must have been grafted onto the Kevlar surface through HRP-mediated radical initiated grafting reaction. The probably mechanism of HRP catalyzed grafting of AM onto Kevlar surface is proposed.     

Grafting of acrylamide onto cellulosic fibers via dielectric-barrier discharge

Fully bleached kraft pulp (BKP) and thermomechanical pulp (TMP) fibers were grafted with acrylamide via dielectric-barrier discharge treatment at various treatment dosages. The results indicate that increased dielectric-barrier discharge treatment leads to the increased polymerization and incorporation of acrylamide onto fiber surfaces. Greater incorporation of poly(acrylamide) occurs on the BKP fibers than the TMP at the same treatment conditions. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) and scanning electron microscopy (SEM) indicate that dielectric-barrier discharge initiated modifications to fiber surface topo-chemistry occur across the fiber such that the sheet is randomly peppered with modified areas; however, it occurs in patches on individual fibers as opposed to occurring as an evenly distributed thin film. SEM and elemental analysis also showed that the incorporation of acrylamide onto the fiber surface increases with increased treatment dosages.     

丙烯酸改性聚醚砜中空纤维渗透汽化膜的研究

采用自由基聚合反应制备了丙烯酸接枝改性的聚醚砜中空纤维渗透汽化膜,该膜用于醇／水分离获得了良好的效果。结果表明,通过改变聚合单体的浓度可以控制膜的接枝率,并调节膜的选择性和通量。改性膜的红外光谱和电镜分析结果表明：膜的接枝反应主要发生在中空纤维膜的内表面,膜的外表面接枝程度很低。力学性能测试表明接枝后膜的拉伸强度减弱。     

Polypropylene fibers modified by plasma treatment for preparation of Ag nanoparticles

A novel method for preparing poly(propylene-graft-2-methacrylic acid 3-(bis-carboxymethylamino)-2-hydroxy-propyl ester)-silver fibers (PPG-IAg fibers) by plasma-induced grafting polymerization is presented in this study. The chelating groups, -N(CH2COO-)2 (GMA-IDA), on the surface of the PPG-I fibers are the coordination sites for chelating silver ions. At these sites, Ag nanoparticles were grown first by reduction with UV light with a wavelength of 366 nm, and second, through immersion in a 24% formaldehyde solution with pH values set variously at 2, 5, 8, and 11. The characteristics of the PPG-I fibers with differing durations of plasma treatment were monitored by using a Fourier transform infrared (FT-IR) spectroscope. Scanning electronic microscopy (SEM) and elemental analysis show that the percentage of GMA-IDA grafted onto PP fiber reaches a maximum when the plasma treatment time is 3 min. Plasma treatment time beyond a certain length of time results in an abundance of free radicals and causes considerable cross-linking on the fiber surface which thus decreases the extent of grafting. Moreover, the crystalline phase of Ag nanoparticles is identified by using X-ray diffraction (XRD). When the PPG-I fibers are reduced by the UV light method, SEM and TEM microscopes reveal that the size of the Ag nanoparticles on the fiber surface decreases significantly with the increase of pH values in aqueous solutions. Notably, in the reduction of formaldehyde solution, the particle size of Ag nanoparticles reaches a minimum at the lowest pH value. The TEM observations show that Ag nanoparticles are distributed both in the exterior and interior of the grafting layer. In addition, under high pH values the distribution of the Ag nanoparticles permeate more deeply in the GMA-IDA grafting layer due to the swelling effect of the GMA-IDA polymer.     

Effect of surface modification by bromination and metalation on Kevlar fibre-epoxy adhesion

This research uses metalation, bromination, and grafting to modify the surface of Kevlar fibre. The resulting fibre was characterized with tensile measurement, infrared spectroscopy, intrinsic viscosity, and scanning electron microscopy (SEM). From the SEM micrographs, the surface morphology of the bromine etched Kevlar fibre has a rougher surface than the untreated fibre. Furthermore, the tensile strength of Kevlar fibre decreases with the increase of bromine treating time. The interlaminar shear strength (ILSS) of the fibre-reinforced epoxy composite was measured. The results show that the ILSS of the bromoacetic acid-grafted Kevlar sample can be increased by 12%, while that of epichlorohydrin-grafted Kevlar can be increased by 8%.     

MODIFICATION OF SILK FIBER via EMULSION GRAFT COPOLYMERIZATION WITH FLUOROACRYLATE

2,2,3,3,4,4,5,5-Octafluoropentyl acrylate was grafted onto silk fiber in a two-step heterogeneous system through the vinyl bonds of acryloyloxyethyl isocyanate modified on the silk.The grafted copolylner was analyzed by FTIR and WAXD,and the results revealed that the fluoroacrylate was successfully grafted onto silk fiber and the crystalline structure of silk fibroin withβ-sheet structure was not changed after graft copolymerization.The FT-IR corrected method was used to simulate the grafting yield onto ...     

Characterization and Studies on Grafting of Methyl Methacrylate onto PAN Fibers

The graft copolymerization of methyl methacrylate (MMA) onto commercial acrylic fibers (PAN) has been studied using Azobis(isobutyro)nitrile (AIBN) as an initiator. MMA grafting initiated by radicals formed from thermal decomposition of AIBN. In this study, the effects of monomer and initiator concentration, time and temperature reaction on the grafting yield have been investigated.

The optimum conditions for this grafting reaction were obtained with an MMA concentration of 0.7 M, an AIBN concentration of 0.0073 M, a reaction temperature of T=85°C and with a 60 min reaction time.

The fiber structure has been investigated by different experimental techniques of characterization such as Fourier transform infrared spectroscopy (FT‐IR), calorimetric analysis (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), water absorption and the physical and mechanical properties has also been investigated in this study. The thermal analysis data showed that by increasing grafting yield, little changes have occurred in fibers samples up to 13.5% of grafting yield and the thermal transitions of grafted fibers have approximately the same behavior compared with the raw fibers sample. Grafting also slightly affected the fiber morphology. The experimental data of mechanical properties clearly show that by increasing grafting yield, max extension will decrease but this change up to 13.5% grafting yield is barely noticeable. Grafting of poly MMA improved water absorption.     

Preparation and Antibacterial Function of Quaternary Ammonium Salts Grafted Cellulose Fiber Initiated by Fe2 +-H2O2 Redox

The surface contact disinfecting technique is a newly developed method for water sterilization. In this paper, the grafted quaternary ammonium salts (QAS) antibacterial fibers were prepared and designed to apply for the surface contact disinfecting process in water treatment. The antibacterial fibers were directly prepared by grafting methacryloxylethyl benzyl dimethyl ammonium chloride (DMAE-BC) onto cellulose fiber using thiocarbonate-H₂O₂ redox system. All kinds of factors in the grafting reactions, such as reaction time, reaction temperature, monomer concentration, initiator concentration, which influence the percentage of grafting, were studied and optimized. The modified cellulose fibers were characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscope(SEM). The effects of the percentage of grafting of the grafted cellulose fibers on bactericidal activity were also studied. The spread plate method was used to characterize the bactericidal activity. The disinfection process was further investigated by directly observing the morphology of the bacterial cells adsorbed on the antibacterial fibers with SEM and measuring extracelluar total protein concentration in suspension. The poly(DMAE-BC)-grafted cellulose ?ber was found to exhibit particularly high activity against E.coli.     

Radiation-induced grafting of acrylamide onto guar gum in aqueous medium: Synthesis and characterization of grafted polymer guar-g-acrylamide

Mutual radiation grafting technique has been applied to carry out grafting of acrylamide (AAm) onto guar gum (GG) using high-energy Co⁶⁰ γ radiation to enhance its flocculating properties for industrial effluents. The grafted product was characterized using analytical probes like elemental analysis, thermal analysis, Fourier transformed infrared (FTIR), X-ray diffraction (XRD) and scanning electron microscope (SEM). The grafting extent was observed to decrease with the dose rate and increase with the concentration of AAm. Thermo gravimetric analysis (TGA) of grafted and ungrafted samples indicated better stability of grafted product. γ and microwave radiation effect on grafted and virgin GG has also been reported.     

Surface modification of polyethylene fiber by graft polymerization

To improve the wettability and adhesion, graft polymerization of acrylamide (AAm) and glycidyl methacrylate (GMA) was performed onto the surface of ultra-high modulus polyethylene (UHMPE) fiber pretreated with Ar plasma. Following the plasma treatment and the subsequent exposure to air to introduce peroxides onto the fiber surface, graft polymerization onto the UHMPE fiber was allowed to proceed from the polymer peroxides either in deaerated monomer solution at an elevated temperature (degassing method), or in aerated monomer solution containing riboflavin at 30°C under UV irradiation (photoinduction method). The monomer solution was prepared from water and dioxane for AAm and GMA, respectively. After rigorous removal of homopolymers, surface analysis of the grafted fibers was performed with ATR-FTIR and XPS, which revealed that PAAm and PGMA chains were grafted in the surface region of fibers. The grafting rate of PAAm by the photoinduction method was much higher than that by the degassing method when compared at the same concentration of the AAm solution. The amount of PGMA grafted was greatly affected by UV irradiation time, but depended on plasma treatment time to an insignificant extent if the treatment was carried out for longer than 30 s. Reaction of propylamine with the PGMA-grafted surface resulted in the appearance of a nitrogen peak in the XPS spectrum, suggesting the presence of epoxy groups on the surface of PGMA grafted fiber. © 1994 John Wiley & Sons, Inc.     

Liquid crystal of nanocellulose whiskers’ grafted with acrylamide

12%acrylamide(AM) was grafted onto the surface of nanocellulose whiskers(NCW),which was self-assembled to be the chiral nematic suspension at 3%content.The acrylamide grafted NCW(AM-g-NCW) was characterized with Fourier Transform Infrared Spectroscopy(FTIR).The grafting ratio was measured by elemental analysis.The degrees of crystallinity of the AM-g-NCW were measured by X-ray diffraction(XRD).The liquid crystalline properties of the AM-g-NCW were investigated by the polarizing optical microscopy(POM).The AM-g-NCW was found to self-assembly to be a lyotropic state.     

Irradiation‐induced grafting of acrylonitrile onto activated carbon fiber

Viscose‐based activated carbon fiber (VACF) was modified with acrylonitrile (AN) by γ‐irradiation‐induced grafting polymerization. Effects of the grafting conditions, such as concentrations of AN and divinylbenzene (DVB), pH value, and solvent on the grafting process were studied. The physicochemical properties of the fibers were characterized. The results show that AN can be effectively grafted onto the surface of VACF with the addition of DVB. The grafting yield is higher than 12% according to thermogravimetric (TG) analysis. The study shows that DVB can improve the grafting degree of AN in the form of grafting chains or agglomerate materials. After grafting modification, VACF shows a small decrease in the specific surface area. Copyright © 2009 John Wiley & Sons, Ltd.     

Improvement of interfacial adhesion and nondestructive damage evaluation for plasma-treated PBO and Kevlar fibers/epoxy composites using micromechanical techniques and surface wettability

Comparison of interfacial properties and microfailure mechanisms of oxygen-plasma treated poly(p-phenylene-2,6-benzobisoxazole (PBO, Zylon) and poly(p-phenylene terephthalamide) (PPTA, Kevlar) fibers/epoxy composites were investigated using a micromechanical technique and nondestructive acoustic emission (AE). The interfacial shear strength (IFSS) and work of adhesion, Wa, of PBO or Kevlar fiber/epoxy composites increased with oxygen-plasma treatment, due to induced hydrogen and covalent bondings at their interface. Plasma-treated Kevlar fiber showed the maximum critical surface tension and polar term, whereas the untreated PBO fiber showed the minimum values. The work of adhesion and the polar term were proportional to the IFSS directly for both PBO and Kevlar fibers. The microfibril fracture pattern of two plasma-treated fibers appeared obviously. Unlike in slow cooling, in rapid cooling, case kink band and kicking in PBO fiber appeared, whereas buckling in the Kevlar fiber was observed mainly due to compressive and residual stresses. Based on the propagation of microfibril failure toward the core region, the number of AE events for plasma-treated PBO and Kevlar fibers increased significantly compared to the untreated case. The results of nondestructive AE were consistent with microfailure modes.     

Mechanical properties of fiber reinforced styrene-butadiene rubbers using surface-modified UHMWPE fibers under EB irradiation

Aiming to develop a high performance fiber reinforced rubber of SBR, a special technique using electron beam (EB) irradiation-induced graft-polymerization was applied to ultra-high molecular-weight polyethylene (UHMWPE) fibers. Although UHMWPE is chemically inert, N-vinyl formamide (NVF) could be graft-polymerized onto the UHMWPE fiber surface with this special technique. A maximum grafting percentage of 23.6% was achieved. The composite of SBR and grafted UHMWPE fibers with maximum grafting indicated a linear increase in the initial modulus and strength with the fiber content. At the fiber content of 10%, the initial modulus was improved about five times with respect to that of the pure SBR, while the strength was done about twice. At this moment, only a small reduction could be observed in the strain compared with that of pure SBR. The fiber reinforced rubber with a good performance was obtained in the system of SBR and grafted UHMWPE fibers.     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

含季铵基离子交换纤维的制备研究

以辐射接枝丙烯酸(AA)后的聚丙烯(PP)无纺布(PP-g-AA)为基材,采用紫外引发的方法接枝甲基丙烯酰氧乙基三甲基氯化铵(DMC),建立了一种制备阴离子交换纤维的新方法,得到了PP-g-AA-DMC纤维.研究了丙烯酸接枝率、DMC浓度、溶剂种类、光照时间,浸泡时间等因素对DMC接枝率的影响,结果表明,DMC的接枝率随着丙烯酸接枝率、DMC浓度、光照时间和纤维浸泡时间的增加而增大.接枝前后纤维的红外光谱分析表明,DMC被成功接枝在PP-g-AA基材上.吸附性能测定结果表明,纤维对水中以阴阳离子存在的金属铬均具有较好的吸附性能.     

Preparation, telomerization, immobilization and application of N-alkyl L-phenylalanine-derived polymerizable organogelator for reversed-phase high-performance liquid chromatography

Silica-polymer hybrid materials (Sil-T1) have been successfully synthesized from a self-assembling polymerizable organogelator; N'-octadecyl-N(alpha)-(4-vinyl)-benzoyl-L-phenylalanineamide (C(18)-L-Phe-St or 1). Telomerization of compound 1 has been done with commonly used silane coupling agent; 3-mercaptopropyltrimethoxysilane (MPS), and the telomer (T1) was grafted onto porous silica surface to prepare a stationary phase (Sil-T1) for reversed-phase high-performance liquid chromatography. The composition of the new hybrid material (Sil-T1) was determined by elemental analysis, DRIFT-IR, TGA and by (13)C and (29)Si (CP/MAS) NMR spectroscopic measurements. The elemental analysis measurements revealed that the surface coverage by organic phase in Sil-T1 is significantly (about 135%) lower than commercial polymeric octadecylsilyalted silica (ODS-p). In addition, the results of (13)C CP/MAS NMR demonstrated that the N-alkyl moieties of the grafted polymers chain in Sil-T1 remained disordered, amorphous, and mobile represented by gauche conformational form. Furthermore, from the characterization data, the successful grafting process and unagglomerated state of the grafted particles (as observed by scanning electron microscopic, SEM measurements) prove the material to be suitable for HPLC application. The evaluation of chromatographic performance has been done from the retention studies of different size and shape PAHs and aromatic positional isomers. Significantly higher selectivity for PAHs was attributed by Sil-T1 than ODS-p regardless it has low surface coverage and lower order of alkyl chain. The enhancement of selectivity obtained by Sil-T1 can be explained by the contribution of multiple pi-pi interactions between the guest PAHs and the pi-electrons sources (carbonyls and aromatic moieties) of the organic phase of Sil-T1.     

玻璃纤维表面的乙烯基单体接枝聚合

用玻璃纤维表面处理剂ＭＡＣ处理玻璃纤维后，再进行臭氧处理，使玻璃纤维的表面产生活性中心，引发苯乙烯、甲基丙烯酸甲酯、及丙烯酸等乙烯基单体在玻璃纤维表面上接枝聚合。接枝纤维的密度减小，对水的浸润性下降，红外光谱及扫描电镜观察证明玻璃纤维表面上接枝聚合物的存在。     

Surface derivatization of poly(p-phenylene terephthalamide) fiber designed for novel separation and extraction media

The surface derivatization of poly(p-phenylene terephthalamide) fiber was studied. The obtained surface-derivatized filaments were packed into a fused-silica capillary to evaluate its surface characteristics by using GC. As the stationary phase for GC the surface-derivatized fibers showed higher retention for alkanes and alkylbenzenes than that with the untreated Kevlar fiber. The improvements on the retention power and the peak shape were observed on the benzyl-modified fibrous stationary phase. The derivatized fibrous materials were also evaluated as the extraction medium in fiber-in-tube SPE, and the effect of the surface modification on the extraction power was compared to the parent fiber. The results indicated that the modified fiber possessed a higher extraction power than the untreated fiber. Based on the facts, the successful modification of the fiber surface was estimated.     

“Surface-photografting”: new applications to synthetic fibers

“Surface-photografting” with UV-irradiation of polypropylene (PP) fiber and film and high-strength polyethylene (HSPE) yarn has been made with acrylic acid (AA) and acrylamide (AM) as monomers and benzophenone (BP), 4-chlorobenzophenone (4-BCP) and hydroxylcyclohexylacetophenone (HHA) as photoinitiators using a new continuous method. The grafting reaction occurs in a thin liquid layer on the fiber or film substrate, which is presoaked in a solution containing initiator and monomer. After irradiation with a highpressure mercury lamp, HPM 15 (2 kW) from Philips, for 5–20 sec at about 50°C the fiber and film surface is completely covered with a 2–8 nm thick layer of grafted polymer, analyzed by electron spectroscopy for chemical analysis. The grafting efficiency is 70–80%, i.e. only 20–30% of the polymer is homopolymer which can be removed by extraction. The grafted layers are so thin that they cannot be analyzed as weight increase (<0.1% of fiber weight). Absolute values for the amount of grafted AA polymer is analyzed by microtitration of the COOH groups at the fiber surface. The results agree well with the relative ESCA values. Grafting of commercial PP yarn with AA increases the adsorption of Crystal Violet dye with a factor of about 6. Grafting the same yarn with AM increases the adhesion to epoxy resin by a factor of 3–4 without affecting the mechanical properties of the fiber more than a few percent. For comparison, strips of blown PP film (5 mm wide) are modified by “surface-photografting” with AM. With increasing grafting, the contact angle for drops of distilled water decreases from 90° to 20°, indicating extensive wetting. The adhesion to epoxy resin increases from about 0.35 to 1.7 N/mm², i.e. with a factor of about 5 when the film surface is completely covered. Other comparisons are made with grafting of commercial HSPE yarn. Grafting with AA increases the adsorption of Crystal Violet dye by a factor of about 6. Grafting with AM increases the adhesion to epoxy resin from 0.25 to 1.3 N/nm², i.e. with a factor of 5. The bulk mechanical properties of the HSPE filaments are not affected by the grafting measured as tensile strength 2.7±0.1 GPa, elongation at break 4.8±0.3%, and Young's modulus 55±3 GPa, both before and after “surface-photografting”.